Hardware is based of:
Empia EM2874B
Micronas DRX 3913KA2
NXP TDA18271HDC2
Only DVB-C supported currently since missing firmware.
According to my tests, DRX 3913KA2 demodulator requires firmware
in order to support DVB-T mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We still need to power up the controller to avoid unsightly self-immolation
should something try to access its registers, but the sensor can stay
powered down unless the camera was actually operating at suspend time.
This gets rid of the camera LED flash on resume, fixing OLPC bug #11644.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only one frame known to the DMA engine in scatter/gather mode, but
it still tells us that any or all of frames 1-3 are done at each completion
interrupt. Avoid the creation of junk frames by being sure to only
"complete" one on each interrupt.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I had learned through hard experience that dinking around with the DMA
descriptors while the C1_DESC_ENA enable bit was set is a recipe for all
kinds of truly malicious behavior on the hardware's part, regardless of
whether the DMA engine is actually operating at the time. That
notwithstanding, the driver did so dink, resulting in "green frame"
captures and the death of the system in random, spectacular ways.
Move the tweaking of C1_DESC_ENA to the same function that sets the
descriptor so we know that we'll never try to set a descriptor while that
bit is set.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Experience shows that, on the Armada platform, it can take as much as 120ms
for the DMA engine to actually shut down after it has been told to. So a
40ms timeout is not adequate; use 150ms instead. Also make sure we don't
leave the DMA_ACTIVE flag set once things are down.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The marvell cam driver retained just enough of the owner-tracking logic
from cafe_ccic to be broken; it could, conceivably, cause the driver to
release DMA memory while the controller is still active. Simply remove the
remaining pieces and ensure that the controller is stopped before we free
things.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The controller stop/restart logic could possibly restart DMA after the
driver things things have stopped, with suitably ugly results. Make sure
that we only restart the hardware if we're supposed to be streaming.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds clk_prepare/clk_unprepare calls to the pxa_camera
driver by using the helper functions clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer CEU versions, e.g., the one, used on sh7372, support image sizes
larger than 2560x1920. Retrieve maximum sizes from platform properties.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_power_on() calls client's .s_power(1) method, which can try to
access the client hardware. This, however, is typically only possible,
after calling host's .add() method, because that's where the host driver
usually turns the master clock on.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes rc_core to not load the IR decoders at load time,
postponing it to load only if a RC_DRIVER_IR_RAW device is
registered via rc_register_device.
We use a static boolean variable, to ensure decoders modules
are only loaded once.
Tested with rc-loopback device only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some of buttons, like power-on key or onkey, may only generate interrupts
when pressed and not actually be mapped as gpio in the system. Allow
setting gpio to invalid value and specify IRQ instead to support such
keys. The debounce timer is used not to debounce but to ignore new IRQs
coming while button is kept pressed.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
request_any_context_irq() should handle the case when using GPIO expanders
that themselves use threaded IRQs, and so the premise of change
7e2ecdf438 is incorrect.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pull core/iommu changes for v3.4 from Ingo Molnar
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/iommu/intel: Increase the number of iommus supported to MAX_IO_APICS
x86/iommu/intel: Fix identity mapping for sandy bridge
Add timing data for Hitachi SP10Q010 display and allow configuration
of the 4bpp palette. For 4bpp framebuffer enable reversed order of
pixels in a byte. This requires defining FB_CFB_REV_PIXELS_IN_BYTE
and additionally setting var.nonstd to the value FB_NONSTD_REV_PIX_IN_B.
Note that it is not enough to set da8xx_fb_var.nonstd to this value
statically, since FBIOPUT_VSCREENINFO ioctl might pass var struct with
.nonstd field set to zero or another value. Therefore this setting must
be adjusted in fb_check_var() according to the requested bpp value.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Remove incorrect SEC_MINI_B settings-TODO complete this section.
Correct break and remove return -EINVAL within set tone. It appears
there is a bug that occasionally something other than ON/OFF is
sent stalling the driver. Just continue and write back registers.
Set register b2 in setup. This is the set voltage pin which
isn't used in lmedm04 driver but it is always set to 0x1.
Correct the if statements in set_tuner_rf.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes for previous patch I liked to do.
Just move tuner init and sleep to own functions from the demod
init and sleep functions. Functionality remains still almost the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c failures were caused by enabling both i2c gates
at the same time while putting the tuners asleep.
This patch removes the init() and sleep() callbacks from the tuner,
to prevent frontend.c from calling
i2c_gate_ctrl
tuner init / sleep
i2c_gate_ctrl
without holding the lock.
tuner init() and sleep() are instead called in frontend init() and
sleep().
Signed-off-by: Gordon Hecker <ghecker@gmx.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct dvb_usb_device *d can never be NULL so don't waste time
checking for this.
Rationale: the urb's context is set when usb_fill_bulk_urb() is called
in dib0700_rc_setup(), and never changes after that. d is dereferenced
unconditionally in dib0700_rc_setup() so it can't be NULL or the
driver would crash right away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes:
drivers/built-in.o: In function `qmi_wwan_bind_shared':
qmi_wwan.c:(.text+0x25b686): undefined reference to `usb_cdc_wdm_register'
make[1]: *** [.tmp_vmlinux1] Error 1
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves 255 bytes of stack on usb_probe() by removing
a char array. In some platforms this is represents a substantial save.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The au8522 driver programs the tuner after programming the demodulator,
but the tuner should be programmed first. This patch fixes this behavior.
EDIT: Apparantly Devin created a similar patch some time ago, but hasn't
submitted it for merge. I never saw his patch, but I thank him anyhow
for his efforts. In addition, Devin pointed out a flaw in my patch:
This newly generated patch takes Devin's comments into account.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Yet another device ID that has started showing up in the wild.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Media-related drivers living outside drivers/media/ (such as the UVC
gadget driver in drivers/usb/gadget/) rely on the media core being
initialized before they're probed. As drivers/usb/ is linked before
drivers/media/, this is currently not the case and will lead to crashes
if the drivers are not compiled as modules.
Register media_devnode_init() as a subsys_initcall() instead of
module_init() to fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for TI's CPSW driver.
The three port switch gigabit ethernet subsystem provides ethernet packet
communication and can be configured as an ethernet switch. Supports
10/100/1000 Mbps.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPSW ethernet switch has a built-in address lookup engine. This patch adds
the code necessary for programming this module.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent race condition between commands on comm channel.
Happened while unloading the driver when switching from
event to polling mode. VF got completion on the last command
before switching to polling mode, but toggle was not changed.
After the fix - VF will not write the next command before
toggle is updated.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Liang Zheng(lzheng@redhat.com) found that in the following topo,
bonding does not send igmp report when we trigger a fail-over of bonding.
eth0--
|-- bond0 -- br0
eth1--
modprobe bonding mode=1 miimon=100 resend_igmp=10
ifconfig bond0 up
ifenslave bond0 eth0 eth1
brctl addbr br0
ifconfig br0 192.168.100.2/24 up
brctl addif br0 bond0
Add 192.168.100.2(br0) into a multicast group, like 224.10.10.10,
then trigger a fali-over in bonding.
You can see that parameter "resend_igmp" does not work.
The reason is that when we add br0 into a multicast group,
it does not propagate multicast knowledge down to its ports.
If we choose to propagate multicast knowledge down to all ports for bridge,
then we have to track every change that is done to bridge, and keep a backup
for all ports. It is hard to track, I think.
Instead I choose to modify bonding to send igmp report for its master.
Changelog:
V2: correct comments
V3: move this check into bond_resend_igmp_join_requests()
V4: only send igmp reports if bond is enslaved to a bridge
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string for MPC5125 FEC. The FEC on MPC5125 additionally
supports RMII PHY interface. Configure controller/PHY interface type
according to the optional phy-connection-type property in the ethernet
node. This property should be either "rmii" or "mii".
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT9M032 is a parallel 1.6MP sensor from Micron controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports cropping, gain,
exposure and v/h flipping controls in monochrome mode with an
external pixel clock.
[Lots of clean up, fixes and enhancements]
Signed-off-by: Martin Hostettler <martin@neutronstar.dyndns.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compute the PLL parameters at runtime using the generic Aptina PLL
helper.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a generic helper function to compute PLL parameters for PLL found in
several Aptina sensors.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fields are set but never used, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is called from non-__init context, just like
tegra_gpio_enable()/disable(). Remove the __init annotation to avoid
section mismatch warnings during compile.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix a bug when using 'ethtool -K ethx tx off' to turn off tx ip checksum,
FCoE CRC offload should not be impacte. The skb_checksum_help() is needed
only if it's not FCoE traffic for ip checksum, regardless of ethtool toggling
the tx ip checksum on or off. Instead of using CHECKSUM_PARTIAL, we will
use CHECKSUM_UNNECESSARY as a proper indication to avoid sw ip checksum
on FCoE frames.
Ref. to original discussion thread:
http://patchwork.ozlabs.org/patch/146567/
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Robert Love <robert.w.love@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows us to avoid a Tx hang when SR-IOV is enabled. This hang
can be triggered by sending small packets at a rate that was triggering Rx
missed errors from the adapter while the internal Tx switch and at least
one VF are enabled.
This was all due to the fact that under heavy stress the Rx FIFO never
drained below the flow control high water mark. This resulted in the Tx
FIFO being head of line blocked due to the fact that it relies on the flow
control high water mark to determine when it is acceptable for the Tx to
place a packet in the Rx FIFO.
The resolution for this is to set the FCRTH value to the RXPBSIZE - 32 so
that even if the ring is almost completely full we can still place Tx
packets on the Rx ring and drop incoming Rx traffic if we do not have
sufficient space available in the Rx FIFO.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of dropping the packet, we keep the skb buffer, and return
NETDEV_TX_BUSY to let upper layer retry send. This will not cause
endless loop, because the host is taking data away from ring buffer,
and we have called the stop_queue before returning NETDEV_TX_BUSY.
The stop_queue was called in the function netvsc_send() in file
netvsc.c, then it returns to rndis_filter_send(), which returns to
netvsc_start_xmit() in file netvsc_drv.c. So the NETDEV_TX_BUSY is
indeed returned AFTER queue is stopped.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve namespace issues when FCoE or DCB is not enabled.
The issue is with certain configurations we end up with namespace
problems. A simple example:
ixgbe_main.c
- defines func A()
- uses func A()
ixgbe_fcoe.c
- uses func A()
ixgbe.h
- has prototype for func A()
For default (FCoE included) all is good. But when it isn't the namespace
checker complains about how func A() could be static.
To resolve this, created a ixgbe_lib file to contain functions used
by DCB/FCoE and their helper functions so that they are always in
namespace whether or not DCB/FCoE is enabled.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Remove an unnecessary #define and use memcpy
instead of a loop to copy an ethernet address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>