Add support for byte queue limits (BQL), based on the similar
modifications made to intel/igb/igb_main.c from Eric Dumazet
in commit bdbc063129
"igb: Add support for byte queue limits."
A local variable for tx_queue->qindex was introduced in
gfar_clean_tx_ring, since it is now used often enough to warrant it,
and it cleans up the readability somewhat as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
libertas provides a dump_survey implementation based on reading of
a RSSI value. However, this RSSI value is calculated based on the
last received beacon from the associated AP - it is not a good
way of surveying a channel in general, and even causes an error
if the card is not associated to a network.
As this is not appropriate as a survey, remove it. This fixes an
issue where something in userspace is repeatedly calling site-survey
during boot, resulting in many repeated errors as the RSSI value cannot
be read before associating.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program tx gain through iniModesTxGain like on AR9287
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use iniModesFastClock for 5 ghz fast clock specific settings, and
iniAdditional for clock/chip specific initval overrides
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program the ah->ini_japan2484 INI values which were left out by accident
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be
cleared on all non-EDMA PCI/AHB based chipsets anyway.
Limit the memset to the rx status area to improve performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and
used together, and they share the same bitmask in enum ath9k_tx_queue_flags.
Simplify the code that tests for these flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX status fifo is limited to 16 elements. When we send more frames than
that, we can easily loose status, what is not good for rate scaling
algorithm.
On my testing the change does not degrade performance, actually make
is slightly better. Additionally with the patch I can see much less
various rt2x00 warnings in dmesg.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx statuses of aggregated subframes contain packetid of first subframe
in the AMPDU. We can not identify AMPDU subframes based on packedid, so
simply assume that status match first pending frame in the queue. Thats
mostly the same what 2800pci do.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we read tx status register after each urb data transfer. As
callback procedure also trigger reading, that causing we have many
"threads" of reading status. To prevent that introduce TX_STATUS_READING
flags, and check if we are already in process of sequential reading
TX_STA_FIFO, before requesting new reads.
Change timer to hrtimer, that make TX_STA_FIFO overruns less possible.
Use 200 us for initial timeout, and then reschedule in 100 us period,
this values probably have to be tuned.
Make changes on txdone work. Schedule it from
rt2800usb_tx_sta_fifo_read_completed() callback when first valid status
show up. Check in callback if tx status timeout happens, and schedule
work on that condition too. That make possible to remove tx status
timeout from generic watchdog. I moved that to rt2800usb.
Loop in txdone work, that should prevent situation when we queue work,
which is already processed, and after finish work is not rescheduled
again.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch change txdone code to make it similar like txdone in rt2800pci,
process only one entry from queue matching tx status.
Before we processed all pending entries from queue until PACKEDID match,
that caused that we do not report tx statuses correctly.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 provides short preamble information and ERP protection
information on a per-BSS basis, which can be used. Remove flags
stored in the driver, which was incorrect since they were being used
in a global manner.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed.
The HT capabilities of the station and HW can be used instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic to determine whether to use FCC is a bit convoluted.
Use a small helper function to decide whether FCC is to be
used.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not needed and will not be used anyway since
unsupported interfaces are not allowed to be created.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to mask out SWBA/BMISS from the
interrupt mask in start().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 already reports the tx ack status of each frame back to mac80211.
Advertise this by setting IEEE80211_HW_REPORTS_TX_ACK_STATUS for rt2800.
This allows some mac80211 features like frame loss notifications to work
with rt2800.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the system is under heavy load, there can be a significant delay
between the getscl() and time_after() calls inside sclhi(). That delay
may cause the time_after() check to trigger after SCL has gone high,
causing sclhi() to return -ETIMEDOUT.
To fix the problem, double check that SCL is still low after the
timeout has been reached, before deciding to return -ETIMEDOUT.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix that. Also convert this and the related comment to proper commenting
style.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow to compile it if AT91 is enable.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make the ECHI depends on ARCH_AT91
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: devicetree-discuss@lists.ozlabs.org
For interrupt remapping the enablement of the IOMMU MSI
interrupt needs to be deferred because the IOMMU itself will
be initialized before the io-apics are up and running. So
the code to setup the MSI is moved seperated from the
hardware-setup routine now.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Unfortunatly the interrupts for the event log and the
peripheral page-faults are only enabled at boot but not
re-enabled at resume. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
To achieve DT support, we need to populate a custom platform_data in a
private struct from DT information. To simplify code, the adapter and
algorithm are also put into the private struct.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
- nand-ecc-mode : String, operation mode of the NAND ecc mode.
Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
"soft_bch".
- nand-bus-width : 8 or 16 bus width if not present 8
- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stefan Roese <sr@denx.de>
This will allow to enable it from the board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc
and hardware).
Set ecc mode in the boards to soft as currently in the driver.
Move platform data to a common header
include/linux/platform_data/atmel_nand.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: David Woodhouse <dwmw2@infradead.org>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
Fix the following section warning in drivers/iommu/amd_iommu.c :
WARNING: vmlinux.o(.text+0x526e77): Section mismatch in reference from the function prealloc_protection_domains() to the function .init.text:alloc_passthrough_domain()
The function prealloc_protection_domains() references
the function __init alloc_passthrough_domain().
This is often because prealloc_protection_domains lacks a __init
annotation or the annotation of alloc_passthrough_domain is wrong.
Cc: stable@vger.kernel.org
Signed-off-by: Steffen Persvold <sp@numascale.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This is an initial drm/kms driver for the displaylink devices.
Supports fb_defio,
supports KMS dumb interface
supports 24bpp via conversion to 16bpp, hw can do this better.
supports hot unplug using new drm core features.
On an unplug, it disables connector polling, unplugs connectors
from sysfs, unplugs fbdev layer (using Kay's API), drops all the
USB device URBs, and call the drm core to unplug the device.
This driver is based in large parts on udlfb.c so I've licensed
it under GPLv2.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Two parts to this, one is simple unplug from sysfs for the device node.
The second adds an unplugged state, if we have device opens, we
just set the unplugged state and return, if we have no device
opens we drop the drm device.
If after a lastclose we discover we are unplugged we then
drop the drm device.
v2: use an atomic for unplugged and wrap it for users,
add checks on open + mmap + ioctl entry points.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to get correct ordering at hot-unplug for userspace,
we need to tear down all the sysfs bits at the correct time.
This adds a helper to allow drivers to remove the sysfs nodes
for all connectors.
Signed-off-by: Dave Airlie <airlied@redhat.com>
a step towards correct hot unplug for USB devices, we need to
remove the userspace facing bits at the unplug time for correct
udev operation.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The USB graphics card driver delays the unregistering of the framebuffer
device to a workqueue, which breaks the userspace visible remove uevent
sequence. Recent userspace tools started to support USB graphics card
hotplug out-of-the-box and rely on proper events sent by the kernel.
The framebuffer device is a direct child of the USB interface which is
removed immediately after the USB .disconnect() callback. But the fb device
in /sys stays around until its final cleanup, at a time where all the parent
devices have been removed already.
To work around that, we remove the sysfs fb device directly in the USB
.disconnect() callback and leave only the cleanup of the internal fb
data to the delayed work.
Before:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb0 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
remove /2-1.2:1.0/graphics/fb0 (graphics)
After:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
Cc: stable@vger.kernel.org
Tested-by: Bernie Thompson <bernie@plugable.com>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>