mactime was being overwritten by the function ath9k_rx_skb_preprocess. Fixed by
memsetting rx_status in ath_rx_tasklet.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The proper place to configure bss info is at assoc notification. So that
ath9k continues to work if the supirous bssid notification will be
removed in future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci is suffering from beacon skew in AP mode. Some powersaving
clients (like VOIP phones) are getting into trouble after some time
when the beacon skew is getting too big.
The ralink legacy drivers contain a function that indicates that the
beacon timer is off by 1us per tbtt. And this function works around
that by reducing the beacon interval for every 64th beacon transmission
by 64us (the smallest possible value). Do the same in rt2800pci.
This allows proper powersaving when rt2800pci is used in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tested in AR9462 Rev:2, both hardware capability flag are set
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2200 driver does not use these defines, it uses geo struct instead.
Therefore remove them from its header.
Note: we keep them in the ipw2100 driver's header, because the driver
still uses them.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On systems with multiple NICs, it's nice to know which
one is producing warnings. Here is an example of the
new ouput:
ath: wiphy0: Failed to stop TX DMA, queues=0x005!
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "mac80211_hwsim: Add tsf to beacons, probe responses and radiotap
header" was setting the mactime on wrong hwsim radio. This patch fixes it.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Is possible that we stop queue and then do not wake up it again,
especially when packets are transmitted fast. That can be easily
reproduced with modified tx queue entry_num to some small value e.g. 16.
If mac80211 already hold local->queue_stop_reason_lock, then we can wait
on that lock in both rt2x00queue_pause_queue() and
rt2x00queue_unpause_queue(). After drooping ->queue_stop_reason_lock
is possible that __ieee80211_wake_queue() will be performed before
__ieee80211_stop_queue(), hence we stop queue and newer wake up it
again.
Another race condition is possible when between rt2x00queue_threshold()
check and rt2x00queue_pause_queue() we will process all pending tx
buffers on different cpu. This might happen if for example interrupt
will be triggered on cpu performing rt2x00mac_tx().
To prevent race conditions serialize pause/unpause by queue->tx_lock.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On il3945_down procedure we free tx queue data and nullify il->txq
pointer. After that we drop mutex and then cancel delayed works. There
is possibility, that after drooping mutex and before the cancel, some
delayed work will start and crash while trying to send commands to
the device. For example, here is reported crash in
il3945_bg_reg_txpower_periodic():
https://bugzilla.kernel.org/show_bug.cgi?id=42766#c10
Patch fix problem by adding il->txq check on works that send commands,
hence utilize tx queue.
Reported-by: Clemens Eisserer <linuxhippy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unbanked GPIO IRQ handling code made a copy of just
the irq_chip structure for GPIO IRQ lines which caused
problems after the generic IRQ chip conversion because
there was no valid irq_chip_type structure with the
right "regs" populated. irq_gc_mask_set_bit() was
therefore accessing random addresses.
Fix it by making a copy of irq_chip_type structure
instead. This will ensure sane register offsets.
Cc: <stable@vger.kernel.org> # v3.0.x+
Reported-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Tested-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make omap_mpuio_alloc_gc() __devinit as omap_gpio_chip_init()
is __devinit. Otherwise we get:
WARNING: vmlinux.o(.devinit.text+0xa10): Section mismatch in reference
from the function omap_gpio_chip_init() to the function .init.text:omap_mpuio_alloc_gc()
The function __devinit omap_gpio_chip_init() references
a function __init omap_mpuio_alloc_gc().
If omap_mpuio_alloc_gc is only used by omap_gpio_chip_init then
annotate omap_mpuio_alloc_gc with a matching annotation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These two functions are used in drivers that can be
modules, so they need to be exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
NCT6775F and NCT6776F have their own set of registers for FAN_STOP_TIME. The
correct registers were used to read FAN_STOP_TIME, but writes used the wrong
registers. Fix it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
If we fail to locate a requested regulator return -EPROBE_DEFER. If drivers
pass this error code through to their caller (which they really should)
then this will ensure that the probe is retried later when further devices
become available. In the unusual case where a driver doesn't want this
it can override the default behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The present _get_value routine returns the contents of the GPIO Monitor Pin
Status Register(GPMR) starting from the bit whose value is requested to BIT 0
(irrelevant bits are replace by 0).
For e.g. if we request the value of GPIO 6 in the earlier implementation the
value returned is:
BIT6 followed by 6 0's
whereas it should just return BIT6.
This patch addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The chip offers the function to detect the current state of output of the GPO
P3 pins. Useful for reading GPIO output state in Linux' GPIO API, e.g. via
sysfs.
Please note that this only reads back the currently programmed output state,
not the actual electrical level in terms of a GPI function. Finally, GPO3 is
still just an output.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add missing mask to pin bit selection in gpio-lpc32xx.c
(#define GPIO3_PIN_IN_SEL)
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We forgot to set the "key_map" variable here, so it's still NULL. This
was introduced recently in 079c9534a9 "vt:tackle kbd_table".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes:
WARNING: drivers/tty/serial/built-in.o(.data+0x30): Section mismatch in reference from the variable vt8500_platform_driver to the function .init.text:vt8500_serial_probe()
The variable vt8500_platform_driver references
the function __init vt8500_serial_probe()
And mark the remove pointer while we are here.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__ffs() can tell us which is the SEGMENT_SHIFT value
to be used. This will prevent problems when users are
too fast and don't pay attention to the need of fixing
the Shift after changing TRBS_PER_SEGMENT.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The latest released errata for USB2.0 ECN LPM adds new fields to USB2.0
extension descriptor, defines two BESL values for device: baseline BESL
and deep BESL. Baseline BESL value communicates a nominal power savings
design point and the deep BESL value communicates a significant power
savings design point.
If device indicates BESL value, driver will use a value count in both
host BESL and device BESL. Use baseline BESL value as default.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Tested-by: Jason Fan <jcfan@qca.qualcomm.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This resolves the conflict with drivers/usb/host/ehci-fsl.h that
happened with changes in Linus's and this branch at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into gpio/next
Linux 3.3-rc7. Merged into the gpio branch to pick up gpio bugfixes already
in mainline before queueing up move v3.4 patches
Stylus buttons have to be resetted when going out-of-prox.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
num_sifr could go negative since acpi_pcc_get_sqty() returns -EINVAL
on error. Then it could bypass the sanity check (num_sifr > 255).
The subsequent call to kzalloc() would allocate a small buffer, leading
to a memory corruption.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We have several reports which says acer-wmi is loaded on ideapads
and register rfkill for wifi which can not be unblocked.
Since ideapad-laptop also register rfkill for wifi and it works
reliably, it will be fine acer-wmi is not going to register rfkill
for wifi once VPC2004 is found.
Also put IBM0068/LEN0068 in the list. Though thinkpad_acpi has no
wifi rfkill capability, there are reports which says acer-wmi also
block wireless on Thinkpad E520/E420.
Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This patch adds support for some of the devices within a wide variety
of Fujitsu Tablet Computers, both convertibles and slates. Primarily
it allows for the automatic detection of the tablet/notebook mode for
convertible tablet pc's, and orientation for docked slates. It also
adds support for the application panel buttons usually found next to
the tablet screen, and docking station detection for slates.
Signed-off-by: Robert Gerlach <khnz@gmx.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
An rfkill driver based on the fsaa1655g and fsam7440 drivers for
Fujitsu-Siemens Amilo A1655 and M7440 models found at:
http://sourceforge.net/projects/fsaa1655g/http://sourceforge.net/projects/fsam7440/
This adds DMI matching, replaces the procfs files with rfkill devices,
and uses the proper functions to write to the i8042 safely.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Microsoft's documentation about multitouch protocols tells that
if a device presents one touch per report, then it should be treated
as a serial protocol.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most callback functions implementation for tps65217_pmic_ldo234_ops and
tps65217_pmic_dcdc_ops are the same except the rid range checking.
This patch uses tps65217_pmic_ops for all DCDCx, LDO2, LDO3, and LDO4.
And rework tps65217_pmic_set_voltage to make it can be called for
DCDCx, LDO2, LDO3, and LDO4.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DIV_ROUND_CLOSEST performs the computation (x + d/2)/d with better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the quirk HID_QUIRK_MULTITOUCH is present and when hid-multitouch
is loaded, let's pass the device to hid-multitouch even if it has
not been registered in hid-multitouch.
If any other driver wants to take precedence over hid-multitouch,
the usual way of adding it to hid_have_special_driver will work as
the quirk HID_QUIRK_MULTITOUCH won't be set by the generic hid layer.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
LG multitouch panels, such as the one found in Dell ST2220T, has buggy
reports descriptors. With the previous implementation, it was impossible
to rely on the reports descriptors to determine how the different
touches are emitted from the device.
This patch changes the splitting of the different touches in the report
in a more robust way.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Portion of the commit id 080eec4fb4 ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.
kvalo: more details to the commit log
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for the Sitecom LN-031 USB adapter with a AX88178 chip.
Added USB id to find correct driver for AX88178 1000 Ethernet adapter.
Signed-off-by: Joerg Neikes <j.neikes@midlandgate.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has been tested on a machine with the Realtek
RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05).
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq. Without this
property, free_irq does nothing.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert calls to free_irq so that the second argument is the same as the
last argument of the corresponding call to request_irq. Without this
property, free_irq does nothing.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then we can use the regulator id as array index to access the array.
This change makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This function finds the smallest voltage that falls within the specified range,
and then returns the selector. This rename makes the intention more clear.
Also remove unneeded local variables min_vol and max_vol in s5m8767_set_voltage
and s5m8767_set_voltage_buck.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change improves readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the s5m8767_set_voltage_time_sel function, divisor unit is wrong.
ramp_delay is usec unit. So 1000 should be multiplied.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Keep the rails OFF in sleep mode only when the rails are
controlled by external sleep control.
The devices tps65910 and tps65911, both has the sleep input.
The tps65911's sleep input is not same as tps65910's EN3 and hence
taking care of SLEEP input as separate external sleep control input.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>