This patch converts the drivers in drivers/pcmcia/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Marc Zyngier <maz@misterjones.org> [for the viper part]
Acked-by: Manuel Lauss <manuel.lauss@googlemail.com> [for the db1xxx_ss.c part]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
{g|s}etnumtcs() today returns a u8 that is only used by the DCB code
to verify no error occurred. Today the driver implementations return
negative error codes which end up being non-zero so the logic works
out but triggers some sparse warnings.
To fix the sparse warnings convert the return value to an int.
CC: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
dcb netlink code calls setup_tc to init hardware traffic classes
to use for DCB. At some call sites the return values are not
checked for errors and in one case may return -EINVAL back to
the net/dcbnl.c caller which is expecting a u8.
This fixes some smatch hits and although failures are never
seen in practive its best to check return codes.
Reported-by: Dan Carenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old code would += the total errors every time
stats were gathered. Instead, keep a count of short-pkt
and long-pkt counters and then simply add them together
for the rx-over-length stat.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel already has a debug allocator, no need to have one unique to
a single driver. So delete it, replace with kfree, kmalloc, and, in a
few places that need it, kzalloc().
Cc: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory is being allocated by kmalloc and stored in
variable pstAddIndication. However, this memory is
not being freed in all cases. Therefore, this patch
frees it on several exit paths. This patch also
removes a whitespace.
Signed-off-by: Kevin McKinney <klmckinney1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems the USB device ID 0bda:8192 is wrongly assigned to the
RTL8192SU chip and not to the RTL8191SU chip in the USB database.
So this patch moves this device ID from the rtl8192u staging
driver to the rtl8712 staging driver.
This patch was tested with a Radicom WIFIHU embedded wireless
module with a RTL8191SU chip and the USB device ID 0bda:8192.
Without the patch the rtl8192u driver claims this device, but
it does not work. With the patch the rtl8712 driver services
this device and it works.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove copies of the double USB device IDs:
- 0bda:8172
- 0bda:8174
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers may not need setup_ops at all, so let the core supply
some empty ops.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes since V1:
Exclude iio debugfs code in case CONFIG_DEBUG_FS isn't enabled.
Introduce helper function iio_get_debugfs_dentry.
Document additions to struct iio_dev
iio_debugfs_read_reg:
Use snprintf.
Use a shorter fixed length.
Introduce len instead of pointer math.
iio_debugfs_write_reg:
Fix return value use PT_ERR.
Changes since V2:
Use debugfs_remove.
Fix whitespace damage.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The below patch fixes some comments and some typos that I have found
while reading drivers/staging/iio/*
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
app_id comes from the network and can't be trusted. If it's zero then
it will lead to a kernel crash.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chris Kelly <ckelly@ozmodevices.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes following compilation warning:
drivers/misc/bmp085.c: In function ‘bmp085_get_pressure’:
drivers/misc/bmp085.c:238:4: warning: comparison of distinct pointer
types lacks a cast [enabled by default]
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe() function will always fail because we're testing the wrong
variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A read from GadgetFS endpoint 0 during the data stage of a control
request would always return 0 on success (as returned by
wait_event_interruptible) despite having written data into the user
buffer.
This patch makes it correctly set the return value to the number of
bytes read.
Signed-off-by: Thomas Faber <thfabba@gmx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel doc entry for usb_unlink_urb() contains the phrase "This
request is always asynchronous.". The "always" leads to the assumption
that the ->complete() callback is not called from within
usb_unlink_urb(). This is not true. The HCD is allowed to call the
->complete() from within ->urb_dequeue() if it is appropriate for the
hardware.
This patch updates the kernel doc so usb-device driver authors make sure
to drop all locks (and make sure it is okay to drop them) which are
acquired by the complete callback before calling usb_unlink_urb().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the coverity checker puts it:
"Passing argument "sizeof (midi_function) /*8*/" to function "kcalloc"
and then casting the return value to "struct usb_descriptor_header **"
is suspicious. ... In this particular case sizeof(struct
usb_descriptor_header **) happens to be equal to sizeof(struct
usb_descriptor_header *), but this is not a portable assumption."
I believe we really do intend to use 'sizeof(*midi_function)' here, so
this patch makes that change.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"len" is unsigned so it's never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_platform_driver macro, move the usb_disabled() check to
the probe function and get rid of the rather pointless message on module
load.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the cp210x driver to support CP210x multiple
interface devices devices from Silicon Labs. The existing driver
always sends control requests to interface 0, which is hardcoded in
the usb_control_msg function calls. This only allows for single
interface devices to be used, and causes a bug when using ports on an
interface other than 0 in the multiple interface devices.
Here are the changes included in this patch:
- Updated the device list to contain the Silicon Labs factory default
VID/PID for multiple interface CP210x devices
- Created a cp210x_port_private struct created for each port on
startup, this struct holds the interface number
- Added a cp210x_release function to clean up the cp210x_port_private
memory created on startup
- Modified usb_get_config and usb_set_config to get a pointer to the
cp210x_port_private struct, and use the interface number there in the
usb_control_message wIndex param
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noticed with the 8168d (-vb-gr, aka RTL_GIGA_MAC_VER_26).
ConfigX registers should only be written while the Config9346 lock
is held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 529febeee6.
To quote Dirk:
This commit introduces a check for the USB PHY clock.
Problem is that CTRL_PHY_CLK_VALID bit seems not to be present
on all Freescale ehci implementations, at least P1022 does not
have it. So this check always fails and the driver never gets
loaded.
So we need to revert this patch.
Reported-by: Dirk Eibach <Eibach@gdsys.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the big network driver reorg, each vendor directory defaults to
yes, so that older config's can migrate correctly. Looks like this one
got missed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Z2+
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: changes for v3.4 merge window
Here are the changes for v3.4 merge window.
It includes a new glue layer for Samsung's Exynos platform, a simplification of
memory management on DWC3 driver by using dev_xxx functions, a few
optimizations to IRQ handling by dropping memcpy() and using bitshifts, a fix
for TI's OMAP5430 TX Fifo Allocation, two fixes on USB2 test mode
implementation (one on debugfs and one on ep0), and several minor changes such
as whitespace cleanups, simplification of a few parts of the code, decreasing a
long delay to something a bit saner, dropping a header which was included twice
and so on.
The highlight on this merge is the support for Samsung's Exynos platform,
increasing the number of different users for this driver to three.
Note that Samsung Exynos glue layer will only compile on platforms which
provide implementation for the clk API for now. Once Samsung supports
pm_runtime, that limitation can be dropped from the Makefile.
Conflicts:
drivers/usb/dwc3/gadget.c
15d1ad0 hwmon: (f75375s) Catch some attempts to write to r/o registers
b17d656 hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
edeea10 hwmon: (f75375s) Make pwm*_mode writable for the F75387
331255d hwmon: (f75375s) Fix writes to the pwm* attribute for the F75387
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=e4hU
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
hhwmon fixes for 3.3-rc6 from Guenter Roeck:
These patches are necessary for correct operation and management of
F75387.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (f75375s) Catch some attempts to write to r/o registers
hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
hwmon: (f75375s) Make pwm*_mode writable for the F75387
hwmon: (f75375s) Fix writes to the pwm* attribute for the F75387
It includes:
- two fixes for OMAP HDMI
- one fix to make new OMAP functions behave as they are supposed to
- one Kconfig dependency fix
- two fixes for viafb for modesetting on VX900 hardware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=+UnE
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3 from Florian Tobias Schandinat
It includes:
- two fixes for OMAP HDMI
- one fix to make new OMAP functions behave as they are supposed to
- one Kconfig dependency fix
- two fixes for viafb for modesetting on VX900 hardware
* tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6:
OMAPDSS: APPLY: make ovl_enable/disable synchronous
OMAPDSS: panel-dvi: Add Kconfig dependency on I2C
viafb: fix IGA1 modesetting on VX900
viafb: select HW scaling on VX900 for IGA2
OMAPDSS: HDMI: hot plug detect fix
OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Specify voltage in ranges for regulator. Range
used is tolerance specified for OPP.
This helps to achieve DVFS with a wider range of
regulators.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Some callbacks are set too early -- i.e. we can have dma capabilities but
we can't get a dma channel. So wait to get the dma channel before setting
callbacks and change logs consequently.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Should be applied to 3.2-stable.]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode. The corresponding
registers are then read-only. If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Minor formatting cleanup]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values. Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.
The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.
Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.
This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
According to the PRM (Vol3P2), the PCH FDI receiver ISR read for bit lock
should be retried at least once. This patch retries the read 5 times
with a small delay in between reads. I've had reports of display corruption
on resume with "FDI train 1 fail!", so I'm hoping that adding this retry
will mitigate the issue.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're not really errors (well actually I don't know; I don't
understand _DSM and _MUX well enough to say, but I do know they spam
people's logs and seem to be harmless).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: The _DSM error got remove in another patch already]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44250
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Git commit 25f269f173 "[S390] qdio: EQBS retry after CCQ 96"
introduced a regression in regard to the zfcp data router.
Revoke the incorrect simplification of the function call arguments
for the qdio handler to make the zfcp hardware data router working
again.
This is applicable to 3.2+ kernels.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Jan Glauber <jang@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The introduction of the owner field on the pin descriptor was not
properly documented so fix this up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_register_mappings() already requires that every mapping table
entry have a non-NULL name field.
Logically, this makes sense too; drivers should always request a specific
named state so they know what they're getting. Relying on getting the
first mentioned state in the mapping table is error-prone, and a nasty
special case to implement, given that a given the mapping table may define
multiple states for a device.
Remove a small part of the documentation that talked about optionally
requesting a specific state; it's mandatory now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a single centralized name for the default state.
Update PIN_MAP_* macros to use this state name, instead of requiring the
user to pass a state name in.
With this change, hog entries in the mapping table are defined as those
with state name PINCTRL_STATE_DEFAULT, i.e. all entries have the same
name. This interacts badly with the nested iteration over mapping table
entries in pinctrl_hog_maps() and pinctrl_hog_map() which would now
attempt to claim each hog mapping table entry multiple times. Replacing
the custom hog code with a simple pinctrl_get()/pinctrl_enable().
Update documentation and mapping tables to use this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At present, pinctrl_get() assumes that all matching mapping table entries
have the same "function" value, albeit potentially applied to different
pins/groups.
This change removes this restriction; pinctrl_get() can now handle a set
of mapping tables where different functions are applied to the various
pins/groups.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
ARM: at91/tclib: take iomem size from resource
ARM: at91/pit: add traces in case of error
ARM: at91: pit add DT support
ARM: at91: AIC and GPIO IRQ device tree initialization
ARM: at91/board-dt: remove AIC irq domain from board file
ARM: at91/gpio: remove the static specification of gpio_chip.base
ARM: at91/gpio: add .to_irq gpio_chip handler
ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node field
ARM: at91/gpio: add irqdomain and DT support
ARM: at91/gpio: change comments and one variable name
ARM/USB: at91/ohci-at91: remove the use of irq_to_gpio
...
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.
Conflicts:
drivers/rtc/rtc-at91sam9.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-omap1/gpio16xx.c
drivers/gpio/gpio-omap.c
Merge in the runtime-pm-cleanup branch from the gpio tree into
next/cleanup, this resolves a nonobvious merge conflict between
the two branches. Both branches move parts of the gpio-omap
driver into platform code, this takes the superset of both
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>