Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
CC: stable@kernel.org
Reported-by: Federico Quagliata <federico@quagliata.org>
Fixed-by: Federico Quagliata <federico@quagliata.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is the last user of the IRQF_SAMPLE_RANDOM flag for net drivers, and since add_*_randomness
interfaces have now deprecated the flag as a source of external noise, we can remove it.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the system to boot and enables the console and at least
some hardware drivers, as well as some platform error handling.
Tested on a variety of SGI Altix system without issues.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Tested-by: Raymund Will <rw@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pinconf_groups_show() wrote all debug information on one line. Fix it to
match pinconf_pins_show() and be legible.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When pins are requested/acquired/got, some device becomes the owner of
their mux setting. At this point, it isn't certain which mux function
will be selected for the pin, since this may vary between each of the
device's states in the pinctrl mapping table. As such, we should record
the owning device, not what we think the initial mux setting will be,
when requesting pins.
This doesn't make a lot of difference right now since pinctrl_get gets
only one single device/state combination, but this will make a difference
when pinctrl_get gets all states, and pinctrl_select_state can switch
between states.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a serious error, and the pin control system will not function
correctly if it ends up not programing the mapping table entries into
the HW. Instead of just ignoring this, error out.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[rebased to fit the applied patch series, cast error to pointer]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This may be perfectly legitimate. An IP block may get re-used
across SoCs. Not all of those SoCs may need pinmux settings for the
IP block, e.g. if one SoC dedicates pins to that function but
another doesn't. The driver won't know this, and will always
attempt to set up the pinmux. The mapping table defines whether any
HW programming is actually needed.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[rebased to fit the applied patch series]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are already disallowed. Clean up some code that doesn't assume this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This solves the riddle on how the U300 pin controller shall be
able to reference the struct gpio_chip even though these are
two separate drivers: spawn the pinctrl child from the GPIO
driver and pass in the struct gpio_chip as platform data.
In the process we rename the U300 "pinmux-u300" to
"pinctrl-u300" so as not to confuse.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Make all functions internal to core.c static. Remove any of these from
core.h.
* Add any missing EXPORT_SYMBOL_GPL().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify the two files so that the order of function prototypes in the
header matches the order of implementations in the .c file.
Don't prototype a couple of internal functions.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify the two files so that the order of function prototypes in the
header matches the order of implementations in the .c file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of storing a single array of mapping table entries, which
requires realloc()ing that array each time it's extended and copying
the new data, simply store a list of pointers to the individual chunks.
This also removes the need to copy the mapping table at all; a pointer
is maintained to the original table, this saving memory.
A macro for_each_maps() is introduced to hide the additional complexity
of iterating over the map entries.
This change will also simplify removing chunks of entries from the mapping
table. This isn't important right now, but will be in the future, when
mapping table entries are dynamically added when parsing them from the
device tree, and removed when drivers no longer need to interact with
pinctrl.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This mostly makes debugfs files print things in the order that they
were added or acquired, which just feels a little more consistent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It may be common for pinctrl_register_mappings() to be used from __init
context, but there's no reason that additional mappings shouldn't be
added at a later point, e.g. if loading modules that add pin controllers
and their mapping tables.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 77a5988 "pinctrl: changes hog mechanism to be self-referential"
modified the way "hog" entries were represented in the mapping table.
However, the new representation failed some error checks in
pinctrl_hog_map(). Remove the now-bogus error-check, and fix the code
to solve the issue the error-check used to avoid.
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We changed the signature of the pin multiplexing functions to
handle any pin business, so fix up the Sirf driver to call this
new interface and rename some variables to make the semantics
understandable.
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A lookup table would be easier to extend, and the resulting
code is a bit cleaner.
Reported-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
At this point we don't support remote processors that have
a different endianess than the host.
Look out for these unsupported scenarios, and bail out if
encountered.
Reported-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Mark Grosen <mgrosen@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
When creating a virtqueue for rpmsg, tell virtio we're not interested
in "weak" smp barriers, since we're talking to a real device.
On ARM, this means using a DSB instead of a DMB, which is needed
for platforms that kick the remote processor using some kind of
a mailbox device mapped to Device memory (otherwise the kick can
jump ahead and wake the remote processor before it has observed
the changes to the vrings).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Since commit 7bb7aef2 "virtio: rename virtqueue_add_buf_gfp to virtqueue_add_buf",
virtqueue_add_buf_gfp is already rename to virtqueue_add_buf now.
This patch fixes below build error:
CC [M] drivers/rpmsg/virtio_rpmsg_bus.o
drivers/rpmsg/virtio_rpmsg_bus.c: In function 'rpmsg_send_offchannel_raw':
drivers/rpmsg/virtio_rpmsg_bus.c:723: error: implicit declaration of function 'virtqueue_add_buf_gfp'
make[2]: *** [drivers/rpmsg/virtio_rpmsg_bus.o] Error 1
make[1]: *** [drivers/rpmsg] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
There isn't any binary change in sight or evidence of any stability
issue, but as we just begin to get traction we can't rule them out
completely.
To be on the safe side, let's mark rpmsg as EXPERIMENTAL, and remove
it later on after we have several happy users.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Clark <rob@ti.com>
Cc: Mark Grosen <mgrosen@ti.com>
Cc: Ludovic BARRE <ludovic.barre@stericsson.com>
Remoteproc is still under development and as it gets traction we
definitely expect to do some changes in the binary format (most probably
only in the resource table, e.g. the upcoming move to TLV-based entries).
Active testing and use of remoteproc is most welcome, but we don't want
users to expect backward binary compatibility with the preliminary
images we have today.
Therefore mark remoteproc as EXPERIMENTAL, and explicitly inform the user
about this when a new remote processor is registered.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Clark <rob@ti.com>
Cc: Mark Grosen <mgrosen@ti.com>
Cc: Ludovic BARRE <ludovic.barre@stericsson.com>
Add a file called 'name' containing the name of the driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* lpc32xx/drivers: (566 commits)
ARM: LPC32xx: ADC support for mach-lpc32xx
Includes an update to Linux 3.3-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Early revisions of several of the WM8994 variants have register updates
to improve performance. Move these over to using the regmap patch system
instead of open coding them in the audio driver. Since the regmap init
is done by the MFD the code is moved there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
The wm8994_device_init() and wm8994_device_exit() functions were not
annotated as device init and exit functions, meaning they shouldn't
reference __devinitdata.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Oritz <sameo@linux.intel.com>
To enable writing to the regmap debugfs registers file users will
need to modify the source directly and #define REGMAP_ALLOW_WRITE_DEBUGFS.
The reason for this is that it is dangerous to expose this
functionality in general where clients could potentially be PMICs.
[A couple of minor style updates -- broonie]
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are few existing user drivers of dw_dmac. They will break as soon as we
remove unused fields from struct dw_dma_slave. This patch focuses to fix these
user drivers to use dma_slave_config() routine.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds support for DMA_SLAVE_CONFIG in dwc DMAC controller. Fields in
struct dw_dma_slave for passing similar data are preserved in this patch untill
all existing users are fixed.
That will be handled later in this patchset.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
64 bit transfers are possible on both sides in slave transfers (memory as well
as peripherals). This patch adds support for it memory side 64 bit transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Block interrupts give interrupt on completion of every LLI, which is actually
too much interrupts. This is just not required for current functioning of
dw_dmac.
So, just don't handle them at all.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use already defined function dev_get_platdata() instead of accessing
pdev->dev.data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Total number of channels is passed in pdata->nr_channels variable, thus we must
not use magic number '7' for total number of channels.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Flow controller information is passed now from DMA_SLAVE_CONFIG option. This
patch makes changes in pl08x driver to use device_fc from it instead of platform
data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
.device_fc is added in struct dma_slave_config recently. All user drivers, which
want DMA to be the flow controller must pass this field as false. As earlier
driver don't look to use this feature, mark it false for now.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The suspend and resume implementation is through dev_pm_ops in dmac. So
in order to support hibernation, freeze, thaw, restore and poweroff
features are required.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Move pm_runtime_put() to the end of intel_mid_dma_free_chan_resources()
because there is no sense in allowing runtime suspend while the driver
is still accessing the device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The error status mask (MASK_ERR) has the same format as the other
masks (MASK_TFR, MASK_BLOCK etc) and must be cleared the same way.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This commit:
12d6d41276: clocksource: scx200_hrt: Convert scx200 to use clocksource_register_hz
Breaks the build on x86-32:
drivers/clocksource/scx200_hrt.c: In function ‘init_hrt_clocksource’:
drivers/clocksource/scx200_hrt.c:95:0: error: unterminated argument list invoking macro "pr_info"
drivers/clocksource/scx200_hrt.c:84:2: error: ‘pr_info’ undeclared (first use in this function)
It could not possibly have been build tested, because it had this mismerge:
pr_info("enabling scx200 high-res timer (%s MHz +%d ppm)\n",
printk(KERN_INFO "enabling scx200 high-res timer (%s MHz +%d ppm)\n",
mhz27 ? "27":"1", ppm);
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/n/tip-jceb26fns5w7tv8edlivhxpa@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The driver currently only supports the PS1000 controller.
It fixes the report descriptor by removing a non-existing axis and
clearing the constant bit on the d-pad and button input reports.
Signed-off-by: Andreas Hübner <andreas@k4n.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>