Commit graph

153,333 commits

Author SHA1 Message Date
Jarod Wilson
8791d63af0 [media] imon: don't wedge hardware after early callbacks
This patch is just a minor update to one titled "imon: Input from ffdc
device type ignored" from Corinna Vinschen. An earlier patch to prevent
an oops when we got early callbacks also has the nasty side-effect of
wedging imon hardware, as we don't acknowledge the urb. Rework the check
slightly here to bypass processing the packet, as the driver isn't yet
fully initialized, but still acknowlege the urb and submit a new rx_urb.
Do this for both interfaces -- irrelevant for ffdc hardware, but
relevant for newer hardware, though newer hardware doesn't spew the
constant stream of data as soon as the hardware is initialized like the
older ffdc devices, so they'd be less likely to trigger this anyway...

Tested with both an ffdc device and an 0042 device.

Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-26 17:04:29 -02:00
Eric Dumazet
bb349bb4b1 be2net: allocate more headroom in incoming skbs
Allocation of 64 bytes in skb headroom is not enough if we have to pull
ethernet + ipv6 + tcp headers, and/or extra tunneling header.

Its currently not noticed because netdev_alloc_skb_ip_align(64) give us
more room, thanks to power-of-two kmalloc() roundups.

Make sure we ask for 128 bytes so that side effects of upcoming patches
from Ian Campbell dont decrease benet rx performance, because of extra
skb head reallocations.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Vasundhara Volam <vasundhara.volam@emulex.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:51:00 -05:00
Wei Liu
40206dd98f xen-netfront: correct MAX_TX_TARGET calculation.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:48:35 -05:00
Ariel Elior
85b26ea18e bnx2x: Update version to 1.72.0 and copyrights
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:52 -05:00
Ariel Elior
7a752993fe bnx2x: Recoverable and unrecoverable error statistics
Add statistics for tracking parity errors from which we successfully
recovered and those which were deemed unrecoverable.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:52 -05:00
Ariel Elior
95c6c6165e bnx2x: Recovery flow bug fixes
1. Sample mcp pulse and mcp sequence in nic load instead of in init_one
as they may change by the time we want to use them.

2. Allow cnic to access device during nic load (by adding a new "LOADING" state
to recovery flow). This prevents the unnecessary cnic timeout which resulted
by cnic attempting to access because nic is loading, but being blocked because
of the Recovery state.

3. Issue 'fake' driver load command to mcp when last driver unloads to prevent
mcp from taking ownership. When recovery is complete unload fake driver to
allow mcp to initialize the hardware before first driver loads.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:52 -05:00
Ariel Elior
889b9af34f bnx2x: Track active PFs with bitmap
The recovery register (to which a hardware lock has been added in previous
patch) is used amongst other things to track the active PFs. The old
implementation which used a per path counter is not viable in a virtualized
environment where a pf may increment the counter and then have the kernel
crash around it preventing the counter from ever reaching zero.
In the new implementation the scenario described will result in the PF timing
out against the mcp, which will clear the PF's bit in the bitmask allowing
recovery process to proceed.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:52 -05:00
Ariel Elior
f16da43b5d bnx2x: Lock PF-common resources
Use hardware locks to protect resources common to several Physical Functions. In
a virtualized environment the RTNL lock only protects a PF's driver against
the PFs sharing it's VMs with regard to device resources. Other PFs may reside
in other VMs under other OSs, and are not subject to the lock. Such resources
which were previously protected implicitly by the RTNL lock must now be
protected explicitly with dedicated HW locks.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:52 -05:00
Ariel Elior
d1e2d9660e bnx2x: Loaded Firmware Version Validation
In a virtualized environment it is possible for a loading driver to discover
that Firmware is already loaded to the device, and that this FW does not match
its own. This can happen for example if different Physical Functions are
Assigned to different VMs in which different driver versions are loaded. The
code in this patch ensures that only drivers with matching FW are loaded over
the device, and that in the case described above where the Firmware version
doesn't match the driver load is aborted.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:51 -05:00
Ariel Elior
89db4ad830 bnx2x: Function Level Reset Final Cleanup
1. Fix bug where return value is ignored
2. Improve printouts
3. Fix typos

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:51 -05:00
Ariel Elior
c22610d000 bnx2x: Obtain Bus Device Function from register
BDF was obtained from kernel but since in virtualized environment
(e.g. physical device assigment in KVM) the function number may
not be the real one, the info must be obtained from the device.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:51 -05:00
Ariel Elior
127a425e8f bnx2x: Removing indirect register access
In virtualized environments indirect access to the device may not be supported
(depending on the Hypervisor type). Indirect device access was used since in
some harware contexts (i.e. certain chipset and BIOS) every access the driver
makes across the pci is followed by a BIOS initiated Zero Length Read to the
same address. When accessing widebus registers this zero length read corrupts
the serialization of the read/write sequence resulting with errors. To avoid
this problem widebus registers are always accessed via the DMAE or the indirect
interface. However, the 57712x and 578xx devices intercept the zero length read
and so using the indirect interface with these devices is not necessary. Since
PDA is only supported for 57712x and 578xx the indirect access to device was
restricted to 57710 and 57711x.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:51 -05:00
Ariel Elior
8d7b02783b bnx2x: Support Queue Per Cos in 5771xx devices
Enable the use of up to three hardware queues for transmission. The queues
are always dequed round robin (i.e. strict priority, PFC and ETS are not
supported). This does allow the allocation of a seperate HW queue for low
volume, high priority traffic which will be serviced more promptly.

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-26 13:39:51 -05:00
Michal Kubecek
590dfe2f3b agp: fix scratch page cleanup
In error cleanup of agp_backend_initialize() and in agp_backend_cleanup(),
agp_destroy_page() is passed virtual address of the scratch page. This
leads to a kernel warning if the initialization fails (or upon regular
cleanup) as pointer to struct page should be passed instead.

Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2012-01-26 18:36:48 +00:00
Mark Brown
a24f64a648 regmap: Reset device debugfs when reinitialising the cache
Most of the data exposed via debugfs is for or from the cache so reset
all the debugfs configuration to make sure everything is up to date with
the latest configuration, especially if we're changing cache type.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-26 18:34:49 +00:00
Dave Airlie
c8fe74ae9a Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux: (24 commits)
  drm/i915: fixup forcewake spinlock fallout in drpc debugfs function
  drm/i915: debugfs: show semaphore registers also on gen7
  drm/i915: allow userspace forcewake references also on gen7
  drm/i915: Re-enable gen7 RC6 and GPU turbo after resume.
  drm/i915: Correct debugfs printout for RC1e.
  Revert "drm/i915: Work around gen7 BLT ring synchronization issues."
  drm/i915: rip out the HWSTAM missed irq workaround
  drm/i915: paper over missed irq issues with force wake voodoo
  drm/i915: Hold gt_lock across forcewake register reads
  drm/i915: Hold gt_lock during reset
  drm/i915: Move reset forcewake processing to gen6_do_reset
  drm/i915: protect force_wake_(get|put) with the gt_lock
  drm/i915: convert force_wake_get to func pointer in the gpu reset code
  drm/i915: sprite init failure on pre-SNB is not a failure
  drm/i915: VBT Parser cleanup for eDP block
  drm/i915: mask transcoder select bits before setting them on LVDS
  drm/i915: Add Clientron E830 to the ignore LVDS list
  CHROMIUM: i915: Add DMI override to skip CRT initialization on ZGB
  drm/i915: handle 3rd pipe
  drm/i915: simplify pipe checking
  ...
2012-01-26 18:25:54 +00:00
Hans Verkuil
23268ae5f0 [media] vivi: don't set V4L2_CAP_DEVICE_CAPS for the device_caps field
V4L2_CAP_DEVICE_CAPS is valid for the capabilities field only as per
the spec.

Found with v4l2-compliance.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-26 15:35:54 -02:00
Jesper Juhl
e4b444369c [media] drxk_hard: does not need to include linux/version.h
This patch removes the unneeded include.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-26 15:35:25 -02:00
Antti Palosaari
cf427952ad [media] anysee: repeat failed USB control messages
Control message load increased heavily after CI/CAM support due
to dvb_ca_en50221. It looks like CI/CAM drops to non-working
state easily after error is returned to its callbacks. Due to
that, add some logic to avoid errors repeating failed messages.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-26 14:46:09 -02:00
Mark Brown
e8f00041a6 Provide managed versions of regulator_get() and regulator_bulk_get(),
saving code in error handling and cleanup paths by ensuring that that
 the regulators will be automatically unregistered when the device is
 unregistered.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPITWJAAoJEBus8iNuMP3defMP/0rHwUk/XEVZHj0OLdA6r33f
 mDATRNX40BAllDUinYyrEWBhEFDWSxJQ1lA6iustO529gkd66j0n24g702GdRnvQ
 Hh2tFS73lmU75JrdTKprVQVV1P0vwDPtm9BbWCbpKl1TJ77z396KrzrO+pHqEVdQ
 FkPweqqGhwBcA/FHy8k8nGiMWk/6pMIbOkaaWRtxCtMxhC05qKOpL90VOEwut2Hb
 0SL5QQUgYCjYzuIqdcOWBrgYcxt7COAS3Z0etgEgSIISdBa38SygRqiLnRZ1AqgX
 gWb7/+v3ont+PEEbjo4wsmO9anGamIUaHY449KKTY6EJnJxbJt6Z4wB86dT9C35s
 l3BjwCfROa+hs0HOS08ake9/y51dpIqiv+T5+jiY+h5dyt+lPxBRAZiVKP2jUo09
 5womi/gt9loy37iQRkMVCGK5ZBnyFet+KpCPYR0Bx3mjBt/O4sqGniZBN7FUx5KS
 ZDBzVFihKLxLFP5xCWi5+Z/sr+wiCGSLKelawznavYCUzo0WYfUo6UrBR2r8U2QI
 2xSE5qzRBLqvdwi/2NQnj/5kbuzv2iiOPAR2PZhwgWPxc0yj1icWCu8d2voKILag
 1I7qGAKaA0E/CXveaf/xlWEFMpuyE+THvXlE2q9s+giV9+DRcEXMbr3uX26xh4Vl
 vwPSfBApJLg7FerS6Lmj
 =Sj0B
 -----END PGP SIGNATURE-----

Merge tag 'topic/devm' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into HEAD

Provide managed versions of regulator_get() and regulator_bulk_get(),
saving code in error handling and cleanup paths by ensuring that that
the regulators will be automatically unregistered when the device is
unregistered.
2012-01-26 16:07:46 +00:00
Tony Lindgren
b9130b776e pinctrl: add checks for empty function names
This is needed as otherwise we can get the following when
dealing with buggy data in a pinmux driver for
pinmux_search_function:

Unable to handle kernel NULL pointer dereference at virtual
address 00000000
...
PC is at strcmp+0xc/0x34
LR is at pinmux_get+0x350/0x8f4
...

As we need pctldev initialized to call ops->list_functions,
let's initialize it before check_ops calls and pass the
pctldev to the check_ops functions. Do this for both pinmux
and pinconf check_ops functions.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-26 14:13:11 +01:00
Tony Lindgren
9e2551e10b pinctrl: fix pinmux_hog_maps when ctrl_dev_name is not set
The ctrl_dev_name is optional for struct pinmux_map assuming
that ctrl_dev is set. Without this patch we can get:

Unable to handle kernel NULL pointer dereference at virtual
address 00000000
...
(pinmux_hog_maps+0xa4/0x20c)
(pinctrl_register+0x2a4/0x378)
...

Fix this by adding adding a test for map->ctrl_dev.
Additionally move the test for map->ctrl_dev earlier
to optimize out the loop a bit.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-26 14:13:05 +01:00
Tony Lindgren
de849eecd0 pinctrl: fix some pinmux typos
Fix some pinmux typos so implementing pinmux drivers
is a bit easier.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-01-26 14:11:31 +01:00
Hiroshi DOYU
7a31f6f48b ARM: IOMMU: Tegra30: Add iommu_ops for SMMU driver
Tegra 30 IOMMU H/W, SMMU (System Memory Management Unit). This patch
implements struct iommu_ops for SMMU for the upper IOMMU API.

This H/W module supports multiple virtual address spaces(domain x4),
and manages 2 level H/W translation pagetable.

Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
2012-01-26 13:59:02 +01:00
Hiroshi DOYU
d53e54b4d4 ARM: IOMMU: Tegra20: Add iommu_ops for GART driver
Tegra 20 IOMMU H/W, GART (Graphics Address Relocation Table). This
patch implements struct iommu_ops for GART for the upper IOMMU API.

This H/W module supports only single virtual address space(domain),
and manages a single level 1-to-1 mapping H/W translation page table.

[With small fixes by Joerg Roedel]

Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
2012-01-26 13:50:28 +01:00
Tomi Valkeinen
c49d005b6c OMAPDSS: HDMI: PHY burnout fix
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.

This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.

The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.

The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2012-01-26 13:51:36 +02:00
Tomi Valkeinen
0eaf9f52e9 OMAPDSS: use sync versions of pm_runtime_put
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.

Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.

This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
2012-01-26 13:46:24 +02:00
Karol Lewandowski
8a093049c6 regulator: Set apply_uV only when min and max voltages are defined
apply_uV is errornously set when regulator is instantiated from device
tree, even when it doesn't contain any voltage constraints.

This commit fixes error:

  machine_constraints_voltage: CHARGER: failed to apply 0uV constraint

for following regulator description in DTS:

  CHARGER {
	regulator-min-microamp = <100000>;
	regulator-max-microamp = <200000>;
  }

Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-01-26 11:01:21 +00:00
Ingo Molnar
4e9f44ba29 MCE recovery (data path only)
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.10 (GNU/Linux)
 
 iQIcBAABAgAGBQJPHy7VAAoJEKurIx+X31iBHcsP/1VcGuxFAL5i/zBqUqhbS7BL
 s+4or1j3NOcxIePQ9egg1L/sLzD+jmo37ObFMTzFOLwuLeodtJF6e0DXQhR7bMKz
 UqOS4WAhNxRBtZtUqIbIiMoDG4Vny1atdqxDQKzmV88ulTG2+JE5U6sGjfTdWvX7
 gZA6Vj31Dz7p6scPT2j8tnLjFV+XvVJSBp/2rgi2Nw81UzBeIRZRiWZrBMLemPCU
 T82OEffnIpSdn60sktMN/ht99yGQO31zT0c+/72Z0ysZAPlTjFbW7CZJHPZmLIVB
 tPkoTRFOf4iwjy2pZNzs9bB8ord/As3IyTxAsfYUin4N2bX27n058uTQ3CqbgEz+
 pa6C5N0ZrV9plYa9BbgCHmNIkhEONIb3WtH27uh/hZOztDA2CXzPT5mm4FOzmrJ7
 DGVBqmXth6g2jYJNT/K2QgmVMZM0CeXQnoDJP54sXzv7F4dEM5P64Lz6E1kCd5Jf
 x9O1orDnEVXssgEPVtF/eEjIQK/vF7s1BUUlMBZJwdAyTwCiD8RvueG87bApnA2z
 eO8VS62akqjpDt5sHboAGJrjcuhqnkbgtG2dn0EqONzk8DJPnhFXVLmSbvH+KuTC
 OguH2LC5N7n9Wjr5a9Duw2DdIj8njvzFrKVzo/l6r3m99u/Jby54vGk2cPLwfGvp
 /9Y+SK2Ou6LSbPiRU4dP
 =ofSb
 -----END PGP SIGNATURE-----

Merge tag 'mce-recovery-for-tip' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/mce

Implement MCE recovery for the data load error path and assorted cleanups.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2012-01-26 11:40:13 +01:00
Ben Widawsky
6dc0e816bb drm/i915: correct lock type in destroy
This is only relevant when using module unloading, and really only helps
get rid of a probably benign warning.

I can't remember if I sent this out already, but it's not turning up in
any of my searches.

Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-01-26 11:29:23 +01:00
Ben Widawsky
8436473a4b drm/i915: drm/i915: Fix recursive calls to unmap
After the ILK vt-d workaround patches it became clear that we had
introduced a bug.  Chris Wilson tracked down the issue to recursive
calls to unmap. This happens because we try to optimize waiting on
requests by calling retire requests after the wait, which may drop the
last reference on an object and end up freeing the object (and then
unmap the object from the gtt).

After the last patch we can now choose to defer processing the retire
list.

Kudos to Chris Wilson for tracking this one down.

This patch fixes gem_unref_active_buffers from i-g-t. It was tested by
forcing do_idle_maps to true.

This also fixes tests/gem_linear_blits in intel-gpu-tools.

Reported-by: guang.a.yang@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42180
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-01-26 11:25:51 +01:00
Ben Widawsky
b93f9cf14e drm/i915: argument to control retiring behavior
Sometimes it may be the case when we idle the gpu or wait on something
we don't actually want to process the retiring list. This patch allows
callers to choose the behavior.

Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-01-26 11:19:19 +01:00
Bruce Allan
d6cb17d5f8 e1000e: 82574/82583 Tx hang workaround
On 82574/82583, there is a hardware bug which might cause a Tx hang when
the internal buffer is full.  Setting this bit enables a hardware fix to
work around the issue.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:13:21 -08:00
Bruce Allan
c550b12185 e1000e: use hardware default values for Transmit Control register
This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:13:15 -08:00
Bruce Allan
6a92f732f5 e1000e: use default settings for Tx Inter Packet Gap timer
Use the default hardware values for TIPG except for 80003es2lan(*).  The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs).  The only change in
functionality is setting the correct default TIPG for the latter devices.

(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:13:08 -08:00
Bruce Allan
4d24136c8e e1000e: 82579: workaround for link drop issue
When connected to certain switches, the 82579 PHY might drop link
unexpectedly.  Work around the issue by setting the Mean Square Error
higher than the hardware default.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:12:59 -08:00
Bruce Allan
56032be77c e1000e: always set transmit descriptor control registers the same
The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:12:53 -08:00
Bruce Allan
b6fbca2af3 e1000e: default IntMode based on kernel config & available hardware support
Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X.  Set the module parameter log message accordingly.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:12:36 -08:00
Bruce Allan
508da4264a e1000e: re-factor ethtool get/set ring parameter
Make it more like how igb does it, with some additional error checking.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:12:29 -08:00
Bruce Allan
55aa69854a e1000e: pass pointer to ring struct instead of adapter struct
For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:12:19 -08:00
Bruce Allan
c5083cf6d2 e1000e: convert head, tail and itr_register offsets to __iomem pointers
The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations.  Also, change current u8 __iomem pointers
to void __iomem pointers.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:12:13 -08:00
Bruce Allan
7ee913562f e1000e: re-enable alternate MAC address for all devices which support it
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:12:06 -08:00
Bruce Allan
70495a500d e1000e: add Receive Packet Steering (RPS) support
Enable RPS by default.  Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.

v2: added ethtool command to query flow hashing behavior per Ben Hutchings
    and changed the type of rsskey to cleanup the setting of the register
    array and avoid unnecessary casts (as pointed out by Joe Perches).
    The long error messages are not changed since there is nothing in
    the kernel ./Documentation that suggests the preferred method for
    dealing with long messages other than to never break strings; leaving
    them as-is for now.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:11:55 -08:00
Bruce Allan
afd12939a0 e1000e: cleanup Rx checksum offload code
1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
   e1000_rx_checksum() instead of in each call to the function

v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-01-25 23:11:43 -08:00
Rob Herring
0f55239348 sh: intc: remove dependency on NR_IRQS
SH intc has a compile time dependency on NR_IRQS. Make this dependency a
local define so that shmobile (and ARM in general) can have run-time
NR_IRQS setting.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-01-25 20:37:48 -06:00
Rob Herring
feefe73fcb gpio: pxa: explicitly include mach/irqs.h
In preparation to make mach/irqs.h optional and remove from asm/irq.h,
directly include mach/irq.h to get MMP_GPIO_TO_IRQ and PXA_GPIO_TO_IRQ.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-01-25 20:37:43 -06:00
Kim Phillips
65a4a573b7 crypto: caam - fix gcc 4.6 warning
drivers/crypto/caam/ctrl.c: In function 'caam_probe':
drivers/crypto/caam/ctrl.c:49:6: warning: unused variable 'd' [-Wunused-variable]

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2012-01-26 13:36:59 +11:00
David Miller
e55684fadb infiniband: nes: Convert nes_addr_resolve_neigh() over to dst_neigh_lookup().
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-25 21:30:37 -05:00
David Miller
64b7007eb9 infiniband: cxgb4: Convert import_ep() over to dst_neigh_lookup().
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-25 21:30:37 -05:00
David Miller
02b619555a infiniband: Convert dst_fetch_ha() over to dst_neigh_lookup().
Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-25 21:30:36 -05:00