Commit graph

153,333 commits

Author SHA1 Message Date
Florian Fainelli
e147763796 r6040: use definitions for MAC_SM register read/writes
Bit 1 is the reset bit of the MAC status machine register, define and
use it.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-04 15:55:53 -05:00
Florian Fainelli
58dbc691e6 r6040: use MAC_RST bit definition with MCR1 read/writes
MAC_RST bit is already defined, use it instead of 0x1 where applicable.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-04 15:55:53 -05:00
Florian Fainelli
4e16d6ebd6 r6040: define more MCR0 register bits
Define more MCR0-register bits and use them in place of the bits values.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-04 15:55:53 -05:00
Florian Fainelli
49f26720d4 r6040: remove unused variables and definitions
Since the conversion to phylib (3831861b: r6040: implement phylib) some
PHY-related variables and definitions are now useless, remove them.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-04 15:55:52 -05:00
Florian Fainelli
817380e1d0 r6040: use an unique MDIO bus name
We should use an unique MDIO bus name which does not clash with anything
else in the system like the Fixed MDIO bus. The bus is now named:
r6040-<card number> which is unique in the system.

Reported-by: Vladimir Kolpakov <vova.kolpakov@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-04 15:55:52 -05:00
Yogesh Ashok Powar
6b6accc383 mwl8k: Recover from firmware crash
In case of firmware crash, reload the firmware and reconfigure it
by triggering ieee80211_hw_restart; mac80211 utility function.

V2 Addressed following comments from Lennert:
 - Stop the queues during reload
 - Removed atomic_t declaration for hw_restart
 - Extend the firmware reload support for sta firmware as well
 - Other misc changes

Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:47 -05:00
Mohammed Shafi Shajakhan
98f0a5eb02 ath9k: tx queue enable is read only for EDMA chipsets
for EDMA chip AR_Q_TXE (tx enable for each queue) is read only

Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:46 -05:00
Gertjan van Wingerde
7fbaf3efb0 rt2x00: Change RF3853 to RF3053.
According to the latest Ralink vendor drivers, this seems to be the real
RF chipset type.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:46 -05:00
Gertjan van Wingerde
5a87e7a706 rt2x00: RT3593 is also applicable to USB.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:46 -05:00
Jakub Kiciński
d823a50e55 rt2x00usb: Zero USB padding before sending URB
When USB driver requires padding at the end of frame or URB it will report
this need by increasing return value of get_tx_data_len callback. Common
USB code uses that return value as desired URB length.

Ensure that appropriate part of skb's tailroom exists and is zeroed.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
--
 drivers/net/wireless/rt2x00/rt2x00usb.c |   16 +++++++++++++---
 1 files changed, 13 insertions(+), 3 deletions(-)
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:46 -05:00
Jakub Kiciński
4bcafac8c6 rt2800usb: Let rt2x00usb handle USB padding
Older USB drivers does not append end padding to skb but instead report
it in size of data to be transmitted to HW. rt2800usb should follow that
behaviour. Custom write_tx_data callback which was adding pad to skb
is not be needed any more.

Thanks to this patch frames handed back from rt2800usb to mac80211 will
no longer contain end padding.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:46 -05:00
Gertjan van Wingerde
5aa5701590 rt2x00: Convert big if-statements to switch-statements.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:45 -05:00
Gertjan van Wingerde
70127cb694 rt2x00: Whitespace cleanup.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:45 -05:00
Gertjan van Wingerde
bc93eda7e9 rt2x00: Identify rt2800usb chipsets.
According to the latest USB ID database these are all RT2770 / RT2870 / RT307x
devices.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:31:45 -05:00
Christian Lamparter
65a692284d carl9170: move checksum and txseq into subfunctions
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:47 -05:00
Larry Finger
3f81f8f152 rt2800usb: Move ID out of unknown
Testing on the openSUSE wireless forum has shown that a Linksys
WUSB54GC v3 with USB ID 1737:0077 works with rt2800usb when the ID is
written to /sys/.../new_id. This ID can therefore be moved out of UNKNOWN.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:47 -05:00
Stanislav Yakovlev
f961e34ebe ipw2x00: remove reset_port functionality
Removes reset_port since it isn't used anywhere as suggested by Johannes Berg.

Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:46 -05:00
Rajkumar Manoharan
016c217791 ath9k_hw: increase tx status ring buffer size
AR9003 chips read tx status from ring buffer whose max number of
status descriptor is mininal compared to max number of tx buffers.
On a stress condition, it can be easily overflown which might cause
false tx hung detection. Though increasing number of max status
descriptors consumes more memory, it helps to avoid false positive
chip resets.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:46 -05:00
Stanislaw Gruszka
68acc4afb0 iwlegacy: 3945: fix hw passive scan on radar channels
Patch fix firmware error on "iw dev wlan0 scan passive" for
hardware scanning (with disable_hw_scan=0 module parameter).

 iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008.
 iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9
 iwl3945 0000:03:00.0: Start IWL Error Log Dump:
 iwl3945 0000:03:00.0: Status: 0x0002A2E4, count: 1
 iwl3945 0000:03:00.0: Desc       Time       asrtPC blink2 ilink1  nmiPC   Line
 iwl3945 0000:03:00.0: SYSASSERT     (0x5) 0041263900 0x13756 0x0031C 0x00000 764
 iwl3945 0000:03:00.0: Error Reply type 0x000002FC cmd C_SCAN (0x80) seq 0x443E ser 0x00340000
 iwl3945 0000:03:00.0: Command C_SCAN failed: FW Error
 iwl3945 0000:03:00.0: Can't stop Rx DMA.

We have disable ability to change passive scanning to active on
particular channel when traffic is detected on that channel. Otherwise
firmware will report error, when we try to do passive scan on radar
channels.

Reported-and-debugged-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:45 -05:00
Stanislaw Gruszka
81fb461395 iwlegacy: 3945: simplify calculations of retry limit
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:45 -05:00
Stanislaw Gruszka
5d0bef903a iwlegacy: random 3945-rs.c cleanups
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:45 -05:00
Stanislaw Gruszka
5bf0dac47f iwlegacy: 4965: remove one il4965_hdl_beacon
We have two such functions.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:45 -05:00
Stanislaw Gruszka
280ade5ea9 iwlegacy: 3945: get rid of hw_{set,get}_rate
Remove these helpers, some are not unused at all, one can be
unrolled in place of use.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:44 -05:00
Stanislaw Gruszka
616107ed81 iwlegacy: 4965: small tx_cmd build cleanup
Get rid of two inline functions related and simplify a bit
rts_retry_limit calculations.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:44 -05:00
Stanislaw Gruszka
a0c1ef3b12 iwlegacy: 4965: toggle tx antenna inline
Make function static and change antenna number inline.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:44 -05:00
Stanislaw Gruszka
17d4eca643 iwlegacy: move some i/o helpers out of inline
This save us about 20k of text size, and should have no impact on
performance as hot paths do not use much I/O.

Before:
   text	   data	    bss	    dec	    hex	filename
 108512	   1784	    168	 110464	  1af80	drivers/net/wireless/iwlegacy/iwl3945.ko
 165730	   2164	    156	 168050	  29072	drivers/net/wireless/iwlegacy/iwl4965.ko
  91942	    328	     48	  92318	  1689e	drivers/net/wireless/iwlegacy/iwlegacy.ko

After:
   text	   data	    bss	    dec	    hex	filename
  95556	   1784	    168	  97508	  17ce4	drivers/net/wireless/iwlegacy/iwl3945.ko
 154853	   2164	    156	 157173	  265f5	drivers/net/wireless/iwlegacy/iwl4965.ko
  91634	    328	     48	  92010	  1676a	drivers/net/wireless/iwlegacy/iwlegacy.ko

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:44 -05:00
Dan Carpenter
d71be93720 iwlegacy: off by one in iwl3945_hw_build_tx_cmd_rate()
We use "rate_index" like this:
	rate = iwl3945_rates[rate_index].plcp;
The iwl3945_rates[] array has IWL_RATE_COUNT_3945 elements so the
limit here is off by one.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:44 -05:00
Stanislaw Gruszka
2b20920d63 iwlegacy: remove iwl-sta.c
I forgot to remove this file before.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:43 -05:00
Helmut Schaa
9931df2692 rt2x00: Mark active channel's survey data as "in use"
This is just a cosmetical fix since we only return survey data for the
active channel but it allows iw to show that the survey data is
for the currently used channel.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:43 -05:00
Larry Finger
5d07a3d62f b43legacy: Avoid packet losses in the dma worker code
This patch addresses a bug in the dma worker code that keeps draining
packets even when the hardware queues are full. In such cases packets
can not be passed down to the device and are erroneusly dropped by the
code. It is based on commit bad6919469,
which fixes the same problem in b43.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:43 -05:00
Rafał Miłecki
9bd2857188 b43: N-PHY: fix typo in TX power fix
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:42 -05:00
Rafał Miłecki
b97c071840 b43: N-PHY: fix controling RF override
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:42 -05:00
Rafał Miłecki
ed5103edc2 b43: N-PHY: update gain ctl workarounds
Specs were updated, now we match wl according to MMIO dumps.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:42 -05:00
Rafał Miłecki
cc96adddbb b43: add lacking boardflags defines
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:42 -05:00
Luis R. Rodriguez
6ec414fd12 ath9k: make ath_mci_duty_cycle static
This fixes this sparse warning:

  CHECK   drivers/net/wireless/ath/ath9k/mci.c
drivers/net/wireless/ath/ath9k/mci.c:23:4: warning: symbol 'ath_mci_duty_cycle' was not declared. Should it be static?

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:42 -05:00
Djalal Harouni
84c816dad5 drivers/iwlwifi: use dma_zalloc_coherent() for DMA allocation
Replace dma_alloc_coherent()+memset() with the new dma_zalloc_coherent()

Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:41 -05:00
Rafał Miłecki
3dda07b6f9 b43: N-PHY: get idle TSSI values
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:41 -05:00
Rafał Miłecki
2c8ac7eb96 b43: N-PHY: fix success condition of running samples
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:41 -05:00
Rafał Miłecki
9dd4d9b992 b43: N-PHY: move common TX/RX functions
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:41 -05:00
Luis R. Rodriguez
a98aa7ae14 ath9k_hw: fix sparse complaint on ar9003_switch_com_spdt_get()
This fixes this sparse complaint:

make C=2 CF="-D__CHECK_ENDIAN__" M=drivers/net/wireless/ath/

  CHECK   drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21:    expected restricted __le32 [usertype] val
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3544:21:    got restricted __le16 [usertype] switchcomspdt
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21:    expected restricted __le32 [usertype] val
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c:3546:21:    got restricted __le16 [usertype] switchcomspdt

The eep->modalHeader5G.switchcomspdt is a le16 and we return u16,
so just return le16_to_cpu().

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:40 -05:00
Luis R. Rodriguez
76ff9a611d ath5k: avoid sparse warnings on tracing
Just skip the sparse checks on tracing.

  CHECK   drivers/net/wireless/ath/ath5k/base.c
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1: error: incompatible types for operation (<)
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1:    left side has type struct ath5k_hw *<noident>
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:19:1:    right side has type int
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1: error: incompatible types for operation (<)
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1:    left side has type struct ath5k_hw *<noident>
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:37:1:    right side has type int
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1: error: incompatible types for operation (<)
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1:    left side has type struct ath5k_hw *<noident>
include/trace/../../drivers/net/wireless/ath/ath5k/trace.h:63:1:    right side has type int
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
/home/mcgrof/wireless-testing/arch/x86/include/asm/jump_label.h:16:9: error: bad asm output
  CC [M]  drivers/net/wireless/ath/ath5k/base.o

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:40 -05:00
Luis R. Rodriguez
1512a48656 ath9k: fix tx queue sparse complaint
This fixes this rant from sparse:

  CHECK   drivers/net/wireless/ath/ath9k/xmit.c
drivers/net/wireless/ath/ath9k/xmit.c:107:13: warning: context imbalance in 'ath_txq_lock' - wrong count at exit
drivers/net/wireless/ath/ath9k/xmit.c:112:13: warning: context imbalance in 'ath_txq_unlock' - unexpected unlock
drivers/net/wireless/ath/ath9k/xmit.c:123:30: warning: context imbalance in 'ath_txq_unlock_complete' - unexpected unlock
  CC [M]  drivers/net/wireless/ath/ath9k/xmit.

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:40 -05:00
Luis R. Rodriguez
e01ff34edc ath9k_hw: fix sparse warnings on ar9003_rtt.c
This fixes these sparse warnings:

  CHECK   drivers/net/wireless/ath/ath9k/ar9003_rtt.c
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:36:6: warning: symbol 'ar9003_hw_rtt_enable' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:41:6: warning: symbol 'ar9003_hw_rtt_disable' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:46:6: warning: symbol 'ar9003_hw_rtt_set_mask' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:52:6: warning: symbol 'ar9003_hw_rtt_force_restore' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:102:6: warning: symbol 'ar9003_hw_rtt_load_hist' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:135:6: warning: symbol 'ar9003_hw_rtt_fill_hist' was not declared. Should it be static?
drivers/net/wireless/ath/ath9k/ar9003_rtt.c:143:6: warning: symbol 'ar9003_hw_rtt_clear_hist' was not declared. Should it be stati

Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-01-04 14:30:40 -05:00
Mauro Carvalho Chehab
7581e61d8d [media] dvb: Remove ops->info.type from frontends
Now that this field is deprecated, and core generates it for
DVBv3 calls, remove it from the drivers.

It also adds .delsys on the few drivers where this were missed.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04 17:30:34 -02:00
Mauro Carvalho Chehab
e399ce77e6 [media] dvb: get rid of fepriv->parameters_in
This var were used during DVBv3 times, in order to keep a copy
of the parameters used by the events. This is not needed anymore,
as the parameters are now dynamically generated from the DVBv5
structure.

So, just get rid of it. That means that a DVBv5 pure call won't
use anymore any DVBv3 parameters.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04 17:30:02 -02:00
Mauro Carvalho Chehab
a520ca97a5 [media] dvb-core: Fix ISDB-T defaults
using -1 for ISDB-T parameters do the wrong thing. Fix it.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04 17:29:55 -02:00
Mauro Carvalho Chehab
04be0f76a8 [media] dvb_frontend: Fix DVBv3 emulation
For frontends with ISDB-T, DVB-T2, CMDBTH, etc, some code is
needed, in order to provide emulation. Add such code, and check
if the desired delivery system is supported by the frontend.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04 17:29:50 -02:00
Mauro Carvalho Chehab
5bfaaddef8 [media] dvb_frontend: Don't use ops->info.type anymore
Get rid of using ops->info.type defined on DVB drivers,
as it doesn't apply anymore.

Currently, one driver (cxd2820) supports more than one different
info.type, as it can be used for DVB-T/T2 and DVB-C. There are more
drivers like that to come. So, the same frontend will have

different DVBv3 types, depending on the current delivery system.

This breaks the existing logic at dvb_frontend, that assumes that
just one delivery system DVBv3 type is supported by all delsys.

In order to easy the DVBv3->DVBv5 conversion, an ancillary function
that maps DVBv3 delivery systems into DVBv5 were added.

Also, on all places, except for the event logic, the DVBv5 cache
will be used to check parameters, instead of the DVBv5 copy.

This patch simplifies the cache sync logic, and warrants that the
cache will be in a clear state at DVB frontend register. This way,
ops->info.type will be filled to reflect the first delivery system,
providing backward compatibility support for it.

For example, in the cases like cxd2820, where the delivery systems
are defined as:
        .delsys = { SYS_DVBT, SYS_DVBT2, SYS_DVBC_ANNEX_A },

A pure DVBv3 will be able to use both DVB-T and DVB-T2, as, at
DVB cache clear, the ops->info.type will be equal to FE_OFDM.

However, DVB-C won't be visible. A quick workaround would be to
do a DVBv5 call to set the delivery system to SYS_DVBC_ANNEX_A.

After such call, ops->info.type will be equal to FE_QAM, and a
DVBv3 application will see the frontend as a DVB-C one.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04 17:29:36 -02:00
Mauro Carvalho Chehab
9682cea27e [media] dvb: move dvb_set_frontend logic into a separate routine
This change is there in order to prepare the code to avoid calling
 dvb_frontend_ioctl_legacy() from FE_SET_PROPERTY.

A call to dvb_frontend_ioctl_legacy() would require to update the
DVBv3 cache without need, mangling calls for newer delivery system
without any reason.

No functional changes here.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04 17:29:17 -02:00
Mauro Carvalho Chehab
9a27e6a0b7 [media] dvb_frontend: Handle all possible DVBv3 values for bandwidth
Due to DVB-T2, several new possible values for bandwidth were added.
As the DVBv3 struct were updated to handle them, the core needs to
handle all of them, as a DVBv3 application might try to use it.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-01-04 17:29:01 -02:00