The Xen changes were using DMA_ERROR_CODE which isn't defined on a few
platforms, however we reverted the Xen patch that caused use to try and
use this code path earlier in 2.6.39 cycle, so for now lets just force
the code to never take this path and allow it to build again on alpha.
The proper long term answer is probably to store if the dma_addr has
been assigned to alongside the dma_addr in the higher level code,
though I think Thomas wanted to rewrite most of this anyways properly.
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The TCC disable setup was incorrect. This
prevents the GPU from hanging when draw commands
are issued.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We are accessing totally the wrong struct in this case, and putting
uninitialised values into the GPU, which it doesn't like unsurprisingly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
slcan: fix ldisc->open retval
net/usb: mark LG VL600 LTE modem ethernet interface as WWAN
xfrm: Don't allow esn with disabled anti replay detection
xfrm: Assign the inner mode output function to the dst entry
net: dev_close() should check IFF_UP
vlan: fix GVRP at dismantle time
netfilter: revert a2361c8735
netfilter: IPv6: fix DSCP mangle code
netfilter: IPv6: initialize TOS field in REJECT target module
IPVS: init and cleanup restructuring
IPVS: Change of socket usage to enable name space exit.
netfilter: ebtables: only call xt_compat_add_offset once per rule
netfilter: fix ebtables compat support
netfilter: ctnetlink: fix timestamp support for new conntracks
pch_gbe: support ML7223 IOH
PCH_GbE : Fixed the issue of checksum judgment
PCH_GbE : Fixed the issue of collision detection
NET: slip, fix ldisc->open retval
be2net: Fixed bugs related to PVID.
ehea: fix wrongly reported speed and port
...
The following patch sets the MaxPayload setting to match the parent
reading when inserting a PCIE card into a hotplug slot. On our system,
the upstream bridge is set to 256, but when inserting a card, the card
setting defaults to 128. As soon as I/O is performed to the card it
starts receiving errors since the payload size is too small.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If an attempt to get _OSC control of the PCIe native features from the
BIOS fails, report the resulting mask of control flags the BIOS was
willing to grant in the error message. Moreover, if the _OSC support
mask is insufficient for requesting control of the PCIe native features
or pcie_ports_disabled is set, print a diagnostic message containing the
_OSC support mask. This helps to diagnose obscure _OSC-related problems
on a number machines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Callers expect pci_user_{read,write}_config_*() to indicate errors by
returning negative values. Prior to this change, the indicated routines
could return positive error codes (e.g. PCIBIOS_BAD_REGISTER_NUMBER)
which callers would mistakenly interpret as success.
This change converts any non-zero return from the mentioned routines
into unambiguous negative value return codes.
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_vpd_pci22_write() calls pci_vpd_pci22_wait() after writing
PCI_VPD_DATA and PCI_VPD_ADDR to wait for the VPD operation to complete.
The result pci_vpd_pci22_wait() was not checked for error.
This change checks for error.
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We were just lucky that ICH4_GPIO_EN and ICH6_GPIO_EN happen to have
the same value.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
TI816X (common name for DM816x/C6A816x/AM389x family) devices configured
to boot as PCIe Endpoint have class code = 0. This makes kernel PCI bus
code to skip allocating BARs to these devices resulting into following
type of error when trying to enable them:
"Device 0000:01:00.0 not available because of resource collisions"
The device cannot be operated because of the above issue.
This patch adds a ID specific (TI VENDOR ID and 816X DEVICE ID based)
'early' fixup quirk to replace class code with
PCI_CLASS_MULTIMEDIA_VIDEO as class.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If it was preempted, and the variable aer_mask_override is changed
after the spin_unlock_irqrestore it will write an uninitialized
variable by the pci_write_config_dword() function.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The pci_pm_reset() function is not a very nice interface due to its
limitations and conditional behavior (e.g. it doesn't affect devices
in low-power states), but it cannot be simply dropped, because
existing device drivers may depend on it. However, its behavior and
limitations should be well documented, so add an appropriate
kerneldoc comment to it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 2f671e2d allowed us to clear ASPM state when the FADT
tells us it isn't supported, but we don't put this into effect
if the aspm_policy is set to POLICY_POWERSAVE. Enable the
state to be cleared regardless of policy.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Samsung's S3C2416, S3C2443 and S3C2450 includes a USB High-Speed
device controller module. This driver enables support for USB high-speed
gadget functionality for the Samsung S3C24xx SoC's that include this
controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Alexander Neumann <alexander@bumpern.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Comparing an unsigned integer with greater than or equal to zero is
always true. So, it is safe to remove similar checks from
'f_mass_storage.c' and 'file_storage.c'
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On amd64 unsigned is not as wide as pointer and this causes a compiler
warning. Switching to unsigned long corrects the problem.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The __devinit and __devexit macros were added to probe and remove
functions. The macros move the probe and remove functions to the
devinit and devexit sections
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Defer the SET_CONFIG and SET_INTERFACE control transfer's data/status
stages till we are ready to process new CBW from the host. This way we
ensure that we don't loose any CBW during MSC compliance tests and cause
lock up.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB function drivers (e.g. f_mass_storage.c) need to delay or defer the
data/status stages of standard control requests like SET_CONFIGURATION or
SET_INTERFACE till they are done with their bookkeeping and are actually ready
for accepting new commands to their interface.
They can now achieve this functionality by returning USB_GADGET_DELAYED_STATUS
in their setup handlers (e.g. set_alt()). The composite framework will then
defer completion of the control transfer by not completing the data/status stages.
This ensures that the host does not send new packets to the interface till the
function driver is ready to take them.
When the function driver that requested for USB_GADGET_DELAYED_STATUS is done
with its bookkeeping, it should signal the composite framework to continue with
the data/status stages of the control transfer. It can do so by invoking
the new API usb_composite_setup_continue(). This is where the control transfer's
data/status stages are completed and host can initiate new transfers.
The DELAYED_STATUS mechanism is currently only supported if the expected data phase
is 0 bytes (i.e. w_length == 0). Since SET_CONFIGURATION and SET_INTERFACE are the
only cases that will use this mechanism, this is not a limitation.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xHCI 1.0: Max Exit Latency Too Large Error
xHCI 1.0: TT_THINK_TIME set
xHCI 1.0: Block Interrupts for Isoch transfer
xHCI 1.0: Isoch endpoint CErr field set
xHCI 1.0: Control endpoint average TRB length field set
xHCI 1.0: Setup Stage TRB Transfer Type flag
forcewake is controlled by the open and close of the debugfs file. This
assures that buggy applications cannot cause the GT to stay on forever.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The render P-state handling code requires reading from a GT register.
This means that FORCEWAKE must be written to, a resource which is shared
and should be protected by struct_mutex. Hence we can not manipulate
that register from within the interrupt handling and so must delegate
the task to a workqueue.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Found by the new strict checking for the mutex being held whilst
manipulating the forcewake status.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Provide a reference count to track the forcewake state of the GPU and
give a safe mechanism for userspace to wake the GT. This also potentially
saves a UC read if the GT is known to be awake already.
The reference count is atomic, but the register access and hardware wake
sequence is protected by struct_mutex.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Moved the macros around to properly do reads and writes for the given
GPU. This is to address special requirements for gen6 (SNB) reads and
writes.
Registers in the range 0-0x40000 on gen6 platforms require special
handling. Instead of relying on the callers to pick the registers
correctly, move the logic into the read and write functions.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the outputs are active and continuing to access the GATT when we
teardown the PTEs, then there is a potential for us to hang the GPU.
The hang tends to be a PGTBL_ER with either an invalid host access or
an invalid display plane fetch.
v2: Reorder IRQ initialisation to defer until after GEM is setup.
Reported-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch> (855GM)
Tested-by: Pekka Enberg <penberg@kernel.org>
# note that this doesn't fix the underlying problem of the
PGTBL_ER and pipe underruns being reported immediately upon
init on his 965GM MacBook
Reported-and-tested-by: Rick Bramley <richard.bramley@hp.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35635
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36048
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Rely on the GPU snooping into the CPU cache for appropriately bound
objects on MI_FLUSH. Or perhaps one day we will have a cache-coherent
CPU/GPU package...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
... to clarify just how we use it inside the driver and remove the
confusion of the poorly matching agp_type names. We still need to
translate through agp_type for interface into the fake AGP driver.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Currently this is only useful for the rc6 stuff. But this would also be
useful when I finally get around to the logical context + ppgtt stuff.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
For debug & testing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is a race condition between setting PWRCTXA and executing
MI_SET_CONTEXT. PWRCTXA must not be set until a valid context has been
written (or else the GPU could possible go into rc6, and return to an
invalid context).
Reported-and-Tested-by: Gu Rui <chaos.proton@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28582
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Added a new function which waits for the ringbuffer space to be equal to
(total - 8). This is the empty condition of the ringbuffer, and
equivalent to head==tail.
Also modified two users of this functionality elsewhere in the code.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In the failure cases during rc6 initialization, both the power context
and render context may get !refcount without holding struct_mutex.
However, on rc6 disabling, the lock is held by the caller.
Rearranged the locking so that it's safe in both cases.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
They're used in one place, and not providing any descriptive value,
with their names just being approximately the conjunction of the
struct name and the struct field.
This diff was produced with gcc -E, copying the new struct definitions
out, moving a couple of the old comments into place in the new
structs, and reindenting.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We used to have these from the product of (pch, non-pch) * (pipe a,
pipe b). Now we can just use the nice per-pipe reg macros in the
split out crtc_mode_sets.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While g4x had DP, eDP came with Ironlake, so we don't need that code here.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This path, which shouldn't be *that* complicated, is now so littered
with per-chipset tweaks that it's hard to trace the order of what
happens. HAS_PCH_SPLIT() is the most radical change across chipsets,
so it seems like a natural split to simplify the code.
This first commit just copies the existing code without changing
anything.
v2: updated to track removal of call to intel_enable_plane from i9xx_crtc_mode_set
Signed-off-by: Eric Anholt <eric@anholt.net>
Hella-acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The struct sbp2_logical_unit.work items can all be executed in parallel
but are not reentrant. Furthermore, reconnect or re-login work must be
executed in a WQ_MEM_RECLAIM workqueue.
Hence replace the old single-threaded firewire-sbp2 workqueue by a
concurrency-managed but non-reentrant workqueue with rescuer.
firewire-core already maintains one, hence use this one.
In earlier versions of this change, I observed occasional failures of
parallel INQUIRY to an Initio INIC-2430 FireWire 800 to dual IDE bridge.
More testing indicates that parallel INQUIRY is not actually a problem,
but too quick successions of logout and login + INQUIRY, e.g. a quick
sequence of cable plugout and plugin, can result in failed INQUIRY.
This does not seem to be something that should or could be addressed by
serialization.
Another dual-LU device to which I currently have access to, an
OXUF924DSB FireWire 800 to dual SATA bridge with firmware from MacPower,
has been successfully tested with this too.
This change is beneficial to environments with two or more FireWire
storage devices, especially if they are located on the same bus.
Management tasks that should be performed as soon and as quickly as
possible, especially reconnect, are no longer held up by tasks on other
devices that may take a long time, especially login with INQUIRY and sd
or sr driver probe.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We do not need slab allocations for ORB pointer write transactions
anymore in order to satisfy streaming DMA mapping constraints, thanks to
commit da28947e7e "firewire: ohci: avoid separate DMA mapping for
small AT payloads".
(Besides, the slab-allocated buffers that firewire-sbp2 used to provide
for 8-byte write requests were still not fully portable since they
shared a cacheline with unrelated CPU-accessed data.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
firewire-sbp2 already takes care for internal serialization where
required (ORB list accesses), and it does not use cmd->serial_number
internally. Hence it is safe to not grab the shost lock around
queuecommand.
While we are at housekeeping, drop a redundant struct member:
sbp2_command_orb.done is set once in a hot path and dereferenced once in
a hot path. We can as well dereference sbp2_command_orb.cmd->scsi_done
instead.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>