The content of every half of screen is sent out via one interface in
dual-DSI case. The content for every interface is blended by a LM
pair in quad-pipe case, thus a LM pair should not blend any content
that cross the half of screen in this case. Clip plane into pipes per
left and right half screen ROI if topology is quad pipe case.
The clipped rectangle on every half of screen is futher handled by two
pipes if its width exceeds a limit for a single pipe.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/675416/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-9-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Currently, SSPPs are assigned to a maximum of two pipes. However,
quad-pipe usage scenarios require four pipes and involve configuring
two stages. In quad-pipe case, the first two pipes share a set of
mixer configurations and enable multi-rect mode when certain
conditions are met. The same applies to the subsequent two pipes.
Assign SSPPs to the pipes in each stage using a unified method and
to loop the stages accordingly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/675414/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-8-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Currently, only 2 pipes are used at most for a plane. A stage structure
describes the configuration for a mixer pair. So only one stage is needed
for current usage cases. The quad-pipe case will be added in future and 2
stages are used in the case. So extend the stage to an array with array
size STAGES_PER_PLANE and blend pipes per mixer pair with configuration in
the stage structure.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675412/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-7-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Currently MAX_CHANNELS_PER_ENC is defined as 2, because 2 channels are
supported at most in one encoder. The case of 4 channels per encoder is
to be added. To avoid breaking current WB usage case, use dedicated WB
definition before 4 WB usage case is supported in future.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675410/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-6-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The stage contains configuration for a mixer pair. Currently the plane
supports just one stage and 2 pipes. Quad-pipe support will require
handling 2 stages and 4 pipes at the same time. In preparation for that
add a separate define, PIPES_PER_PLANE, to denote number of pipes that
can be used by the plane.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675408/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-5-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
There are 2 pipes in a drm plane at most currently, while 4 pipes are
required for quad-pipe case. Generalize the handling to pipe pair and
ease handling to another pipe pair later. Store pipes in array with
removing dedicated r_pipe.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675406/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-4-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Current code only supports usage cases with one pair of mixers at
most. To support quad-pipe usage case, two pairs of mixers need to
be reserved. The lm_count for all pairs is cleared if a peer
allocation fails in current implementation. Reset the current lm_count
to an even number instead of completely clearing it. This prevents all
pairs from being cleared in cases where multiple LM pairs are needed.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/675400/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-1-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Extend Samsung ACPM (Alive Clock and Power Manager) firmware drivers:
1. Add support for passing DVFS (Dynamic Voltage and Frequency) messages
to configure the clocks in ACPM device.
2. Add Exynos ACPM clock driver, which exposes to Linux several clocks
handled by the ACPM (firmware).
-----BEGIN PGP SIGNATURE-----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=4F4S
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=susi
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-firmware-clk-6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into clk-samsung
Pull Samsung clk driver updates from Krzysztof Kozlowski:
Extend Samsung ACPM (Alive Clock and Power Manager) firmware drivers:
- Add support for passing DVFS (Dynamic Voltage and Frequency) messages
to configure the clocks in ACPM device.
- Add Exynos ACPM clock driver, which exposes to Linux several clocks
handled by the ACPM (firmware)
* tag 'samsung-drivers-firmware-clk-6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
firmware: exynos-acpm: add empty method to allow compile test
MAINTAINERS: add ACPM clock bindings and driver
clk: samsung: add Exynos ACPM clock driver
firmware: exynos-acpm: register ACPM clocks pdev
firmware: exynos-acpm: add DVFS protocol
dt-bindings: firmware: google,gs101-acpm-ipc: add ACPM clocks
Some devices (such as Smaug) report having MOTION_SENSE_FIFO but do not
support controlling the behaviour of the FIFO interrupt via the
FIFO_INT_ENABLE command and in these cases the interrupt is always
enabled. However, currently the code assumes that if MOTION_SENSE_FIFO
is supported then so is FIFO_INT_ENABLE, and when it tries to enable
the interrupt via this command and an unsupported device reports a
failure it then propagates this into failing the sensors probe.
Interpret the return value -EINVAL as a device where FIFO_INT_ENABLE is
not present and the interrupt is always enabled.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Link: https://lore.kernel.org/r/20251112-diogo-smaug_ec_sensorhub-v1-1-f71d4e9eb9d4@tecnico.ulisboa.pt
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Fix incorrect comment to match the filename.
Reviewd-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Signed-off-by: Encrow Thorne <jyc0019@gmail.com>
Reviewed-by: Yixun Lan <dlan@gentoo.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add const qualifiers to the pointers returned from 'container_of' macro
to prevent breaking the const promise on const struct pointers from
parameters.
Once you have a mutable container structure pointer, you can change
structure fields through it, which violates the const guarantee.
Signed-off-by: Adrian Barnaś <abarnas@google.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Set the correct DMA mask. Without this DMA will fail on some setups.
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Message-ID: <20251110-gsp_boot-v9-2-8ae4058e3c0e@nvidia.com>
Compute more of the required FB layout information to boot the GSP
firmware.
This information is dependent on the firmware itself, so first we need
to import and abstract the required firmware bindings in the `nvfw`
module.
Then, a new FB HAL method is introduced in `fb::hal` that uses these
bindings and hardware information to compute the correct layout
information.
This information is then used in `fb` and the result made visible in
`FbLayout`.
These 3 things are grouped into the same patch to avoid lots of unused
warnings that would be tedious to work around. As they happen in
different files, they should not be too difficult to track separately.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Message-ID: <20251110-gsp_boot-v9-1-8ae4058e3c0e@nvidia.com>
Lad Prabhakar says:
====================
net: phy: mscc: Add support for PHY LED control
This patch series adds support for controlling the PHY LEDs on the
VSC85xx family of PHYs from Microsemi (now part of Renesas).
The first two patches simplify and consolidate existing probe code
the third patch introduces the LED control functionality.
The LED control feature allows users to configure the LED behavior
based on link activity, speed, and other criteria.
====================
Link: https://patch.msgid.link/20251112135715.1017117-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devm_phy_package_join() may fail and return a negative error code.
Update vsc85xx_probe_common() to properly handle this failure by
checking the return value and propagating the error to the caller.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251112135715.1017117-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the PHY LED controller in the MSCC VSC85xx driver. The
implementation provides LED brightness and hardware control through the
LED subsystem and integrates with the standard 'netdev' trigger.
Introduce new register definitions for the LED behavior register
(MSCC_PHY_LED_BEHAVIOR = 30) and the LED combine disable bits, which
control whether LEDs indicate link-only or combined link and activity
status. Implement a helper, vsc8541_led_combine_disable_set(), to update
these bits safely using phy_modify().
Add support for LED brightness control and hardware mode configuration.
The new callbacks implement the standard LED class operations, allowing
user control through sysfs. The brightness control maps to PHY LED force
on/off modes. The hardware control get and set functions translate
between the PHY-specific LED mode encodings and the LED subsystem
TRIGGER_NETDEV_* rules.
The combine feature is managed automatically based on the selected
rules. When both RX and TX activity are disabled, the combine feature is
turned off, causing LEDs to indicate link-only status. When either RX or
TX activity is enabled, the combine feature remains active and LEDs
indicate combined link and activity.
Register the LED callbacks for all VSC85xx PHY variants so that the LED
subsystem can manage their indicators consistently. Existing device tree
LED configuration and default behavior are preserved.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251112135715.1017117-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unify the probe implementations of the VSC85xx PHY family into a single
vsc85xx_probe_common() helper. The existing probe functions for the
vsc85xx, vsc8514, vsc8574, and vsc8584 variants contained almost
identical initialization logic, differing only in configuration
parameters such as the number of LEDs, supported LED modes, hardware
statistics, and PTP support.
Introduce a vsc85xx_probe_config structure to describe the per-variant
parameters, and move all common setup code into the shared helper. Each
variant's probe function now defines a constant configuration instance
and calls vsc85xx_probe_common().
Also mark the default LED mode array parameter as const to match its
usage.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251112135715.1017117-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The vsc85xx_led_cntl_set() function currently performs a manual
read-modify-write sequence protected by the PHY lock to update the
LED mode register (MSCC_PHY_LED_MODE_SEL).
Replace this sequence with a call to phy_modify(), which already
handles read-modify-write operations with proper locking inside
the PHY core.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251112135715.1017117-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since 93e86b3bc8 ("net: dsa: Remove legacy probing support")
this struct has no user any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/4053a98f-052f-4dc1-a3d4-ed9b3d3cc7cb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Documentation build reported:
Warning: drivers/dpll/zl3073x/fw.c:365 function parameter 'comp' not described in 'zl3073x_fw_component_flash'
Warning: drivers/dpll/zl3073x/fw.c:365 expecting prototype for zl3073x_flash_bundle_flash(). Prototype was for zl3073x_fw_component_flash() instead
Warning: drivers/dpll/zl3073x/fw.c:365 No description found for return value of 'zl3073x_fw_component_flash'
The kernel-doc comment above `zl3073x_fw_component_flash()` used
the wrong function name (`zl3073x_flash_bundle_flash`) and omitted
the `@comp` parameter. Update the comment to correctly document
the `zl3073x_fw_component_flash()` function and its arguments.
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Link: https://patch.msgid.link/20251112055642.2597450-1-kriish.sharma2006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function mlxsw_sp_flower_stats() calls mlxsw_sp_acl_ruleset_get() to
obtain a ruleset reference. If the subsequent call to
mlxsw_sp_acl_rule_lookup() fails to find a rule, the function returns
an error without releasing the ruleset reference, causing a memory leak.
Fix this by using a goto to the existing error handling label, which
calls mlxsw_sp_acl_ruleset_put() to properly release the reference.
Fixes: 7c1b8eb175 ("mlxsw: spectrum: Add support for TC flower offload statistics")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251112052114.1591695-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ethtool tsconfig Netlink path can trigger a null pointer
dereference. A call chain such as:
tsconfig_prepare_data() ->
dev_get_hwtstamp_phylib() ->
vlan_hwtstamp_get() ->
generic_hwtstamp_get_lower() ->
generic_hwtstamp_ioctl_lower()
results in generic_hwtstamp_ioctl_lower() being called with
kernel_cfg->ifr as NULL.
The generic_hwtstamp_ioctl_lower() function does not expect
a NULL ifr and dereferences it, leading to a system crash.
Fix this by adding a NULL check for kernel_cfg->ifr in
generic_hwtstamp_ioctl_lower(). If ifr is NULL, return -EINVAL.
Fixes: 6e9e2eed4f ("net: ethtool: Add support for tsconfig command to get/set hwtstamp config")
Closes: https://lore.kernel.org/cd6a7056-fa6d-43f8-b78a-f5e811247ba8@linux.dev
Signed-off-by: Jiaming Zhang <r772577952@gmail.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20251111173652.749159-2-r772577952@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace comma between expressions with semicolons.
Using a ',' in place of a ';' can have unintended side effects.
Although that is not the case here, it is seems best to use ';'
unless ',' is intended.
Found by inspection.
No functional change intended.
Compile tested only.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://patch.msgid.link/20251112072709.73755-1-nichen@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A PCI bridge resource lifecycle involves both a "request" and "assign"
phase. At any point in time that resource may not yet be assigned, or may
have failed to assign (because it does not fit).
There are multiple conventions to determine when assignment has not
completed: IORESOURCE_UNSET, IORESOURCE_DISABLED, and checking whether the
resource is parented.
In code paths that are known to not be racing assignment, e.g. post
subsys_initcall(), the most reliable method to judge that a bridge resource
is assigned is to check the resource is parented [1].
Introduce a resource_assigned() helper for this purpose.
Link: http://lore.kernel.org/2b9f7f7b-d6a4-be59-14d4-7b4ffccfe373@linux.intel.com [1]
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251113021446.436830-4-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All of the objects in drivers/virt/ have their own configuration symbols to
gate compilation. I.e. nothing gets added to the kernel with
CONFIG_VIRT_DRIVERS=y in isolation.
Unconditionally descend into drivers/virt/ so that consumers do not need to
add an additional CONFIG_VIRT_DRIVERS dependency.
Fix warnings of the form:
Kconfig warnings: (for reference only)
WARNING: unmet direct dependencies detected for TSM
Depends on [n]: VIRT_DRIVERS [=n]
Selected by [y]:
- PCI_TSM [=y] && PCI [=y]
...where PCI_TSM selects CONFIG_TSM, but fails to select
CONFIG_VIRT_DRIVERS.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511041832.ylcgIiqN-lkp@intel.com/
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251113021446.436830-2-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- Fix vfio selftests to remove the expectation that the IOMMU
supports a 64-bit IOVA space. These manifest both in the original
set of tests introduced this development cycle in identity mapping
the IOVA to buffer virtual address space, as well as the more
recent boundary testing. Implement facilities for collecting the
valid IOVA ranges from the backend, implement a simple IOVA
allocator, and use the information for determining extents.
(Alex Mastro)
-----BEGIN PGP SIGNATURE-----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=ywvT
-----END PGP SIGNATURE-----
Merge tag 'vfio-v6.18-rc6' of https://github.com/awilliam/linux-vfio
Pull VFIO seftest fixes from Alex Williamson:
- Fix vfio selftests to remove the expectation that the IOMMU supports
a 64-bit IOVA space.
These manifest both in the original set of tests introduced this
development cycle in identity mapping the IOVA to buffer virtual
address space, as well as the more recent boundary testing.
Implement facilities for collecting the valid IOVA ranges from the
backend, implement a simple IOVA allocator, and use the information
for determining extents (Alex Mastro)
* tag 'vfio-v6.18-rc6' of https://github.com/awilliam/linux-vfio:
vfio: selftests: replace iova=vaddr with allocated iovas
vfio: selftests: add iova allocator
vfio: selftests: fix map limit tests to use last available iova
vfio: selftests: add iova range query helpers
- Fix issues related to using inadequate data types and incorrect use
of atomic variables in the compressed hibernation images handling
code that were introduced during the 6.9 development cycle (Mario
Limonciello)
- Move a X86_FEATURE_IDA check from turbo_is_disabled() to the places
where a new value for MSR_IA32_PERF_CTL is computed in intel_pstate
to address a regression preventing users from enabling turbo
frequencies post-boot (Srinivas Pandruvada)
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmkWOnoSHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO14gkH/08TYjtNEvC6acD2r5gJTpacdnExWopL
NFmRyhuZM21Ja2gd1q0xtPvcTdAz3rkhB4vqn9KQ0oLkfXj08/+zpRyOP3PzVVSp
bvE/Am28s/VChjDg/MFcP7o/fLSNoL73wK6er+i721KIV1uscK4FydkPNs6gpBHw
03FkUJX8jRjil0Cp6km2O0Zo5SEgm/U6wDjR5Azpdru8VKbI1RaxCMsR0/HnlA9Y
pUAph9NX1UBBjdMFFdn8++Vna8XJX4qe9CiYT7KwGbGx5jUpVBaT9d/hPm0O/mJt
VvNe3Dl5soFM/3yibsvV4sTcZHNPTsIKjuKIqwL4F0TCGug9kxwjFBk=
=r3Fq
-----END PGP SIGNATURE-----
Merge tag 'pm-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix issues related to the handling of compressed hibernation
images and a recent intel_pstate driver regression:
- Fix issues related to using inadequate data types and incorrect use
of atomic variables in the compressed hibernation images handling
code that were introduced during the 6.9 development cycle (Mario
Limonciello)
- Move a X86_FEATURE_IDA check from turbo_is_disabled() to the places
where a new value for MSR_IA32_PERF_CTL is computed in intel_pstate
to address a regression preventing users from enabling turbo
frequencies post-boot (Srinivas Pandruvada)"
* tag 'pm-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Check IDA only before MSR_IA32_PERF_CTL writes
PM: hibernate: Fix style issues in save_compressed_image()
PM: hibernate: Use atomic64_t for compressed_size variable
PM: hibernate: Emit an error when image writing fails
- Limit some checks in the ACPI CPPC library to online CPUs to avoid
accessing uninitialized per-CPU variables when some CPUs are offline
to start with, like during boot with "nosmt=force" (Gautham Shenoy)
- Rework add_boot_memory_ranges() in the ACPI MRRM table parser to fix
memory leaks and improve error handling (Kaushlendra Kumar)
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEcM8Aw/RY0dgsiRUR7l+9nS/U47UFAmkWNu8SHHJqd0Byand5
c29ja2kubmV0AAoJEO5fvZ0v1OO1VsoIAIZJdKrHCGBveZP+Xo2GFhulHRq3534A
M0//mZ23iSXdP4U8lYkQDMOrfuDTqb6AMFKylgsFKh/+AWRtKHxOWoAbdF979xS5
doBdJn1aWt+oJAN/37rYn/cnk+AeTpyejJ94GYdMTHu+5PkoCEFBP7Ecn41ks0UM
0N0UDrxC6+2FwbPunnYFFMP9kSJj273ga3y9t1M2reKjNsjSoBoACuhkYVI/pL/n
Gl8r0Z63wDeN/4YIEOMFEjpdDfUY1HoXg7QQvYSPlWRuq/5OLYJowKumR816pt71
YIrafkZV1UzEKcHeDsmipGfWKghwotVy4XpR68div58iX0oPa7t6tWM=
=t6UM
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix issues in the ACPI CPPC library and in the recently added
parser for the ACPI MRRM table:
- Limit some checks in the ACPI CPPC library to online CPUs to avoid
accessing uninitialized per-CPU variables when some CPUs are
offline to start with, like during boot with 'nosmt=force' (Gautham
Shenoy)
- Rework add_boot_memory_ranges() in the ACPI MRRM table parser to
fix memory leaks and improve error handling (Kaushlendra Kumar)"
* tag 'acpi-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: MRRM: Fix memory leaks and improve error handling
ACPI: CPPC: Limit perf ctrs in PCC check only to online CPUs
ACPI: CPPC: Perform fast check switch only for online CPUs
ACPI: CPPC: Check _CPC validity for only the online CPUs
ACPI: CPPC: Detect preferred core availability on online CPUs
The vcc3v3_pcie20 fixed regulator powers the PCIe device-side 3.3V rail
for pcie2x1l2 via vpcie3v3-supply. The DTS mistakenly set its
regulator-min/max-microvolt to 1800000 (1.8 V). Correct both to 3300000
(3.3 V) to match the rail name, the PCIe/M.2 power requirement, and the
actual hardware wiring on Orange Pi 5.
Fixes: b6bc755d80 ("arm64: dts: rockchip: Add Orange Pi 5")
Cc: stable@vger.kernel.org
Signed-off-by: Mykola Kvach <xakep.amatop@gmail.com>
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Link: https://patch.msgid.link/cf6e08dfdfbf1c540685d12388baab1326f95d2c.1762165324.git.xakep.amatop@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We've had reports from the field that some RK3588 Tiger have random
issues with eMMC errors.
Applying commit a28352cf2d ("mmc: sdhci-of-dwcmshc: Change
DLL_STRBIN_TAPNUM_DEFAULT to 0x4") didn't help and seemed to have made
things worse for our board.
Our HW department checked the eMMC lines and reported that they are too
long and don't look great so signal integrity is probably not the best.
Note that not all Tigers with the same eMMC chip have errors, so the
suspicion is that we're really on the edge in terms of signal integrity
and only a handful devices are failing. Additionally, we have RK3588
Jaguars with the same eMMC chip but the layout is different and we also
haven't received reports about those so far.
Lowering the max-frequency to 150MHz from 200MHz instead of simply
disabling HS400 was briefly tested and seem to work as well. We've
disabled HS400 downstream and haven't received reports since so we'll go
with that instead of lowering the max-frequency.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Fixes: 6173ef24b3 ("arm64: dts: rockchip: add RK3588-Q7 (Tiger) SoM")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251112-tiger-hs200-v1-1-b50adac107c0@cherry.de
[added Fixes tag and stable-cc from 2nd mail]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The xfstests' test-case generic/070 leaves HFS+ volume
in corrupted state:
sudo ./check generic/070
FSTYP -- hfsplus
PLATFORM -- Linux/x86_64 hfsplus-testing-0001 6.17.0-rc1+ #4 SMP PREEMPT_DYNAMIC Wed Oct 1 15:02:44 PDT 2025
MKFS_OPTIONS -- /dev/loop51
MOUNT_OPTIONS -- /dev/loop51 /mnt/scratch
generic/070 _check_generic_filesystem: filesystem on /dev/loop50 is inconsistent
(see xfstests-dev/results//generic/070.full for details)
Ran: generic/070
Failures: generic/070
Failed 1 of 1 tests
sudo fsck.hfsplus -d /dev/loop50
** /dev/loop50
Using cacheBlockSize=32K cacheTotalBlock=1024 cacheSize=32768K.
Executing fsck_hfs (version 540.1-Linux).
** Checking non-journaled HFS Plus Volume.
The volume name is test
** Checking extents overflow file.
Unused node is not erased (node = 1)
** Checking catalog file.
** Checking multi-linked files.
** Checking catalog hierarchy.
** Checking extended attributes file.
** Checking volume bitmap.
** Checking volume information.
Verify Status: VIStat = 0x0000, ABTStat = 0x0000 EBTStat = 0x0004
CBTStat = 0x0000 CatStat = 0x00000000
** Repairing volume.
** Rechecking volume.
** Checking non-journaled HFS Plus Volume.
The volume name is test
** Checking extents overflow file.
** Checking catalog file.
** Checking multi-linked files.
** Checking catalog hierarchy.
** Checking extended attributes file.
** Checking volume bitmap.
** Checking volume information.
** The volume test was repaired successfully.
It is possible to see that fsck.hfsplus detected not
erased and unused node for the case of extents overflow file.
The HFS+ logic has special method that defines if the node
should be erased:
bool hfs_bnode_need_zeroout(struct hfs_btree *tree)
{
struct super_block *sb = tree->inode->i_sb;
struct hfsplus_sb_info *sbi = HFSPLUS_SB(sb);
const u32 volume_attr = be32_to_cpu(sbi->s_vhdr->attributes);
return tree->cnid == HFSPLUS_CAT_CNID &&
volume_attr & HFSPLUS_VOL_UNUSED_NODE_FIX;
}
However, it is possible to see that this method works
only for the case of catalog file. But debugging of the issue
has shown that HFSPLUS_VOL_UNUSED_NODE_FIX attribute has been
requested for the extents overflow file too:
catalog file
kernel: hfsplus: node 4, num_recs 0, flags 0x10
kernel: hfsplus: tree->cnid 4, volume_attr 0x80000800
extents overflow file
kernel: hfsplus: node 1, num_recs 0, flags 0x10
kernel: hfsplus: tree->cnid 3, volume_attr 0x80000800
This patch modifies the hfs_bnode_need_zeroout() by checking
only volume_attr but not the b-tree ID because node zeroing
can be requested for all HFS+ b-tree types.
sudo ./check generic/070
FSTYP -- hfsplus
PLATFORM -- Linux/x86_64 hfsplus-testing-0001 6.18.0-rc3+ #79 SMP PREEMPT_DYNAMIC Fri Oct 31 16:07:42 PDT 2025
MKFS_OPTIONS -- /dev/loop51
MOUNT_OPTIONS -- /dev/loop51 /mnt/scratch
generic/070 33s ... 34s
Ran: generic/070
Passed all 1 tests
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
cc: Yangtao Li <frank.li@vivo.com>
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/20251101001229.247432-1-slava@dubeyko.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Currently, Ethernet is unusable due to an incorrect PHY address.
This commit fixes this, removes the incorrect 25M clock pinctrl,
and adds the missing PHY supply.
Fixes: d809417c5a ("arm64: dts: rockchip: add DTs for 100ASK DShanPi A1")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://patch.msgid.link/20251101120010.41729-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When sync() and link() are called concurrently, both threads may
enter hfs_bnode_find() without finding the node in the hash table
and proceed to create it.
Thread A:
hfsplus_write_inode()
-> hfsplus_write_system_inode()
-> hfs_btree_write()
-> hfs_bnode_find(tree, 0)
-> __hfs_bnode_create(tree, 0)
Thread B:
hfsplus_create_cat()
-> hfs_brec_insert()
-> hfs_bnode_split()
-> hfs_bmap_alloc()
-> hfs_bnode_find(tree, 0)
-> __hfs_bnode_create(tree, 0)
In this case, thread A creates the bnode, sets refcnt=1, and hashes it.
Thread B also tries to create the same bnode, notices it has already
been inserted, drops its own instance, and uses the hashed one without
getting the node.
```
node2 = hfs_bnode_findhash(tree, cnid);
if (!node2) { <- Thread A
hash = hfs_bnode_hash(cnid);
node->next_hash = tree->node_hash[hash];
tree->node_hash[hash] = node;
tree->node_hash_cnt++;
} else { <- Thread B
spin_unlock(&tree->hash_lock);
kfree(node);
wait_event(node2->lock_wq,
!test_bit(HFS_BNODE_NEW, &node2->flags));
return node2;
}
```
However, hfs_bnode_find() requires each call to take a reference.
Here both threads end up setting refcnt=1. When they later put the node,
this triggers:
BUG_ON(!atomic_read(&node->refcnt))
In this scenario, Thread B in fact finds the node in the hash table
rather than creating a new one, and thus must take a reference.
Fix this by calling hfs_bnode_get() when reusing a bnode newly created by
another thread to ensure the refcount is updated correctly.
A similar bug was fixed in HFS long ago in commit
a9dc087fd3 ("fix missing hfs_bnode_get() in __hfs_bnode_create")
but the same issue remained in HFS+ until now.
Reported-by: syzbot+005d2a9ecd9fbf525f6a@syzkaller.appspotmail.com
Signed-off-by: Yang Chenzhi <yang.chenzhi@vivo.com>
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
Link: https://lore.kernel.org/r/20250829093912.611853-1-yang.chenzhi@vivo.com
Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com>
The reset property is not part of the binding, so drop it.
It is also not used by the driver, so it was likely copied
from some vendor-kernel node.
Fixes: 57b1ce9039 ("arm64: dts: rockchip: Add rk3576 SoC base DT")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://patch.msgid.link/20251101140101.302229-1-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Add support for voltage and temperature sensor
- Add a mutex to memory operations on Stratix10 service driver
- Add support for asynchronous communications in the service driver
- Replace scnprintf() with sysfs_emit()
-----BEGIN PGP SIGNATURE-----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=/N3t
-----END PGP SIGNATURE-----
Merge tag 'socfpga_firmware_updates_for_v6.19' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into char-misc-next
Dinh writes:
SoCFPGA firmware updates for v6.19
- Add support for voltage and temperature sensor
- Add a mutex to memory operations on Stratix10 service driver
- Add support for asynchronous communications in the service driver
- Replace scnprintf() with sysfs_emit()
* tag 'socfpga_firmware_updates_for_v6.19' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
firmware: stratix10-rsu: replace scnprintf() with sysfs_emit() in *_show() functions
firmware: stratix10-rsu: Migrate RSU driver to use stratix10 asynchronous framework.
firmware: stratix10-svc: Add support for RSU commands in asynchronous framework
firmware: stratix10-svc: Add support for async communication
firmware: stratix10-svc: Add mutex in stratix10 memory management
firmware: stratix10-svc: Add definition for voltage and temperature sensor
Due to some copy and paste from the manufacturer tree the property
assigned-clock-rate is missing a letter "s". Correct spelling to
reduce dtbs_check output.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://patch.msgid.link/92714b6c-6c0d-4a10-afe4-73ed313c87c0@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>