Analyzing the call frequency without actually using tracing is helpful for
analysis of this infrastructure. The overhead is minimal as it just
increments a per CPU counter associated to each operation.
The debugfs readout provides a racy sum of all counters.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084307.027916598@linutronix.de
Provide tracepoint wrappers for the upcoming RSEQ exit to user space inline
fast path, so that the header can be safely included by code which defines
actual trace points.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.967114316@linutronix.de
For RSEQ the only relevant reason to inspect and eventually fixup (abort)
user space critical sections is when user space was interrupted and the
task was scheduled out.
If the user to kernel entry was from a syscall no fixup is required. If
user space invokes a syscall from a critical section it can keep the
pieces as documented.
This is only supported on architectures which utilize the generic entry
code. If your architecture does not use it, bad luck.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.905067101@linutronix.de
In preparation for rewriting RSEQ exit to user space handling provide
storage to cache the CPU ID and MM CID values which were written to user
space. That prepares for a quick check, which avoids the update when
nothing changed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.841964081@linutronix.de
There is nothing mm specific in that and including mm.h can cause header
recursion hell.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.778457951@linutronix.de
There is no point to have this as a function which just inlines
enter_from_user_mode(). The function call overhead is larger than the
function itself.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.715309918@linutronix.de
Open code the only user in the x86 syscall code and reduce the zoo of
functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.652839989@linutronix.de
Clean up the include ordering, kernel-doc and other trivialities before
making further changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.590338411@linutronix.de
In preparation for a major rewrite of this code, provide a data structure
for rseq management.
Put all the rseq related data into it (except for the debug part), which
allows to simplify fork/execve by using memset() and memcpy() instead of
adding new fields to initialize over and over.
Create a storage struct for event management as well and put the
sched_switch event and a indicator for RSEQ on a task into it as a
start. That uses a union, which allows to mask and clear the whole lot
efficiently.
The indicators are explicitly not a bit field. Bit fields generate abysmal
code.
The boolean members are defined as u8 as that actually guarantees that it
fits. There seem to be strange architecture ABIs which need more than 8
bits for a boolean.
The has_rseq member is redundant vs. task::rseq, but it turns out that
boolean operations and quick checks on the union generate better code than
fiddling with separate entities and data types.
This struct will be extended over time to carry more information.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.527086690@linutronix.de
There is no need to update these values unconditionally if there is no
event pending.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.462964916@linutronix.de
Hypervisors invoke resume_user_mode_work() before entering the guest, which
clears TIF_NOTIFY_RESUME. The @regs argument is NULL as there is no user
space context available to them, so the rseq notify handler skips
inspecting the critical section, but updates the CPU/MM CID values
unconditionally so that the eventual pending rseq event is not lost on the
way to user space.
This is a pointless exercise as the task might be rescheduled before
actually returning to user space and it creates unnecessary work in the
vcpu_run() loops.
It's way more efficient to ignore that invocation based on @regs == NULL
and let the hypervisors re-raise TIF_NOTIFY_RESUME after returning from the
vcpu_run() loop before returning from the ioctl().
This ensures that a pending RSEQ update is not lost and the IDs are updated
before returning to user space.
Once the RSEQ handling is decoupled from TIF_NOTIFY_RESUME, this turns into
a NOOP.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Sean Christopherson <seanjc@google.com>
Link: https://patch.msgid.link/20251027084306.399495855@linutronix.de
Since commit 0190e4198e ("rseq: Deprecate RSEQ_CS_FLAG_NO_RESTART_ON_*
flags") the bits in task::rseq_event_mask are meaningless and just extra
work in terms of setting them individually.
Aside of that the only relevant point where an event has to be raised is
context switch. Neither the CPU nor MM CID can change without going through
a context switch.
Collapse them all into a single boolean which simplifies the code a lot and
remove the pointless invocations which have been sprinkled all over the
place for no value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.336978188@linutronix.de
There is no point to read the critical section element in the newly
registered user space RSEQ struct first in order to clear it.
Just clear it and be done with it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.274661227@linutronix.de
There is no point for this being visible in the resume_to_user_mode()
handling.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.211520245@linutronix.de
Move the comment which documents the RSEQ algorithm to the top of the file,
so it does not create horrible diffs later when the actual implementation
is fed into the mincer.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.149519580@linutronix.de
Scrolling over tons of pointless
{
}
lines to find the actual code is annoying at best.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.085971048@linutronix.de
The RSEQ critical section mechanism only clears the event mask when a
critical section is registered, otherwise it is stale and collects
bits.
That means once a critical section is installed the first invocation of
that code when TIF_NOTIFY_RESUME is set will abort the critical section,
even when the TIF bit was not raised by the rseq preempt/migrate/signal
helpers.
This also has a performance implication because TIF_NOTIFY_RESUME is a
multiplexing TIF bit, which is utilized by quite some infrastructure. That
means every invocation of __rseq_notify_resume() goes unconditionally
through the heavy lifting of user space access and consistency checks even
if there is no reason to do so.
Keeping the stale event mask around when exiting to user space also
prevents it from being utilized by the upcoming time slice extension
mechanism.
Avoid this by reading and clearing the event mask before doing the user
space critical section access with interrupts or preemption disabled, which
ensures that the read and clear operation is CPU local atomic versus
scheduling and the membarrier IPI.
This is correct as after re-enabling interrupts/preemption any relevant
event will set the bit again and raise TIF_NOTIFY_RESUME, which makes the
user space exit code take another round of TIF bit clearing.
If the event mask was non-zero, invoke the slow path. On debug kernels the
slow path is invoked unconditionally and the result of the event mask
evaluation is handed in.
Add a exit path check after the TIF bit loop, which validates on debug
kernels that the event mask is zero before exiting to user space.
While at it reword the convoluted comment why the pt_regs pointer can be
NULL under certain circumstances.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027084306.022571576@linutronix.de
Replace the open coded implementation with the scoped user access guard.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027083745.862419776@linutronix.de
Replace the open coded implementation with the scoped user access
guards
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://patch.msgid.link/20251027083745.799714344@linutronix.de
Replace the open coded implementation with the new get/put_user_inline()
helpers. This might be replaced by a regular get/put_user(), but that needs
a proper performance evaluation.
No functional change intended.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://patch.msgid.link/20251027083745.736737934@linutronix.de
Provide convenience wrappers around scoped user access similar to
put/get_user(), which reduce the usage sites to:
if (!get_user_inline(val, ptr))
return -EFAULT;
Should only be used if there is a demonstrable performance benefit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027083745.609031602@linutronix.de
User space access regions are tedious and require similar code patterns all
over the place:
if (!user_read_access_begin(from, sizeof(*from)))
return -EFAULT;
unsafe_get_user(val, from, Efault);
user_read_access_end();
return 0;
Efault:
user_read_access_end();
return -EFAULT;
This got worse with the recent addition of masked user access, which
optimizes the speculation prevention:
if (can_do_masked_user_access())
from = masked_user_read_access_begin((from));
else if (!user_read_access_begin(from, sizeof(*from)))
return -EFAULT;
unsafe_get_user(val, from, Efault);
user_read_access_end();
return 0;
Efault:
user_read_access_end();
return -EFAULT;
There have been issues with using the wrong user_*_access_end() variant in
the error path and other typical Copy&Pasta problems, e.g. using the wrong
fault label in the user accessor which ends up using the wrong accesss end
variant.
These patterns beg for scopes with automatic cleanup. The resulting outcome
is:
scoped_user_read_access(from, Efault)
unsafe_get_user(val, from, Efault);
return 0;
Efault:
return -EFAULT;
The scope guarantees the proper cleanup for the access mode is invoked both
in the success and the failure (fault) path.
The scoped_user_$MODE_access() macros are implemented as self terminating
nested for() loops. Thanks to Andrew Cooper for pointing me at them. The
scope can therefore be left with 'break', 'goto' and 'return'. Even
'continue' "works" due to the self termination mechanism. Both GCC and
clang optimize all the convoluted macro maze out and the above results with
clang in:
b80: f3 0f 1e fa endbr64
b84: 48 b8 ef cd ab 89 67 45 23 01 movabs $0x123456789abcdef,%rax
b8e: 48 39 c7 cmp %rax,%rdi
b91: 48 0f 47 f8 cmova %rax,%rdi
b95: 90 nop
b96: 90 nop
b97: 90 nop
b98: 31 c9 xor %ecx,%ecx
b9a: 8b 07 mov (%rdi),%eax
b9c: 89 06 mov %eax,(%rsi)
b9e: 85 c9 test %ecx,%ecx
ba0: 0f 94 c0 sete %al
ba3: 90 nop
ba4: 90 nop
ba5: 90 nop
ba6: c3 ret
Which looks as compact as it gets. The NOPs are placeholder for STAC/CLAC.
GCC emits the fault path seperately:
bf0: f3 0f 1e fa endbr64
bf4: 48 b8 ef cd ab 89 67 45 23 01 movabs $0x123456789abcdef,%rax
bfe: 48 39 c7 cmp %rax,%rdi
c01: 48 0f 47 f8 cmova %rax,%rdi
c05: 90 nop
c06: 90 nop
c07: 90 nop
c08: 31 d2 xor %edx,%edx
c0a: 8b 07 mov (%rdi),%eax
c0c: 89 06 mov %eax,(%rsi)
c0e: 85 d2 test %edx,%edx
c10: 75 09 jne c1b <afoo+0x2b>
c12: 90 nop
c13: 90 nop
c14: 90 nop
c15: b8 01 00 00 00 mov $0x1,%eax
c1a: c3 ret
c1b: 90 nop
c1c: 90 nop
c1d: 90 nop
c1e: 31 c0 xor %eax,%eax
c20: c3 ret
The fault labels for the scoped*() macros and the fault labels for the
actual user space accessors can be shared and must be placed outside of the
scope.
If masked user access is enabled on an architecture, then the pointer
handed in to scoped_user_$MODE_access() can be modified to point to a
guaranteed faulting user address. This modification is only scope local as
the pointer is aliased inside the scope. When the scope is left the alias
is not longer in effect. IOW the original pointer value is preserved so it
can be used e.g. for fixup or diagnostic purposes in the fault path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://patch.msgid.link/20251027083745.546420421@linutronix.de
Clang propagates a provided label, which is outside of a cleanup scope to
ASM GOTO despite the fact that __raw_get_mem() has a local label for that
purpose:
"error: cannot jump from this asm goto statement to one of its possible targets"
Using the unsafe wrapper with the extra local label indirection cures that.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/xXr
-----END PGP SIGNATURE-----
Merge tag 'for-6.18-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix memory leak in qgroup relation ioctl when qgroup levels are
invalid
- don't write back dirty metadata on filesystem with errors
- properly log renamed links
- properly mark prealloc extent range beyond inode size as dirty (when
no-noles is not enabled)
* tag 'for-6.18-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: mark dirty extent range for out of bound prealloc extents
btrfs: set inode flag BTRFS_INODE_COPY_EVERYTHING when logging new name
btrfs: fix memory leak of qgroup_list in btrfs_add_qgroup_relation
btrfs: ensure no dirty metadata is written back for an fs with errors
The tables created by jevents.py are only used within the pmu-events.c
file. Change the declarations of those global variables to be static
to encapsulate this.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
When copy metrics into a group also copy default information from the
original metrics.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
If an out-of-memory occurs the expr also needs freeing.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Update comment as the stat_config no longer holds all metrics.
Signed-off-by: Ian Rogers <irogers@google.com>
Fixes: faebee18d7 ("perf stat: Move metric list from config to evlist")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The metric_events exist in the metric_expr list and so this variable
has been unused for a while.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
There are a few situations in the driver where we convert a `usize` into
a `u32` using `as`. Even though most of these are obviously correct, use
`try_from` and let the compiler optimize wherever it is safe to do so.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Message-ID: <20251029-nova-as-v3-3-6a30c7333ad9@nvidia.com>
Use the `image_type` method and compare its result to avoid using `as`.
Reviewed-by: Joel Fernandes <joelagnelf@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Message-ID: <20251029-nova-as-v3-2-6a30c7333ad9@nvidia.com>
Given that the platform TSM owns IDE Stream ID allocation, report the
active streams via the TSM class device. Establish a symlink from the
class device to the PCI endpoint device consuming the stream, named by
the Stream ID.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Alexey Kardashevskiy <aik@amd.com>
Link: https://patch.msgid.link/20251031212902.2256310-10-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The limited number of link-encryption (IDE) streams that a given set of
host bridges supports is a platform specific detail. Provide
pci_ide_init_nr_streams() as a generic facility for either platform TSM
drivers, or PCI core native IDE, to report the number available streams.
After invoking pci_ide_init_nr_streams() an "available_secure_streams"
attribute appears in PCI host bridge sysfs to convey that count.
Introduce a device-type, @pci_host_bridge_type, now that both a release
method and sysfs attribute groups are being specified for all 'struct
pci_host_bridge' instances.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Samuel Ortiz <sameo@rivosinc.com>
Cc: Alexey Kardashevskiy <aik@amd.com>
Cc: Xu Yilun <yilun.xu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251031212902.2256310-9-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There are two components to establishing an encrypted link, provisioning
the stream in Partner Port config-space, and programming the keys into
the link layer via IDE_KM (IDE Key Management). This new library,
drivers/pci/ide.c, enables the former. IDE_KM, via a TSM low-level
driver, is saved for later.
With the platform TSM implementations of SEV-TIO and TDX Connect in mind
this library abstracts small differences in those implementations. For
example, TDX Connect handles Root Port register setup while SEV-TIO
expects System Software to update the Root Port registers. This is the
rationale for fine-grained 'setup' + 'enable' verbs.
The other design detail for TSM-coordinated IDE establishment is that
the TSM may manage allocation of Stream IDs, this is why the Stream ID
value is passed in to pci_ide_stream_setup().
The flow is:
pci_ide_stream_alloc():
Allocate a Selective IDE Stream Register Block in each Partner Port
(Endpoint + Root Port), and reserve a host bridge / platform stream
slot. Gather Partner Port specific stream settings like Requester ID.
pci_ide_stream_register():
Publish the stream in sysfs after allocating a Stream ID. In the TSM
case the TSM allocates the Stream ID for the Partner Port pair.
pci_ide_stream_setup():
Program the stream settings to a Partner Port. Caller is responsible
for optionally calling this for the Root Port as well if the TSM
implementation requires it.
pci_ide_stream_enable():
Enable the stream after IDE_KM.
In support of system administrators auditing where platform, Root Port,
and Endpoint IDE stream resources are being spent, the allocated stream
is reflected as a symlink from the host bridge to the endpoint with the
name:
stream%d.%d.%d
Where the tuple of integers reflects the allocated platform, Root Port,
and Endpoint stream index (Selective IDE Stream Register Block) values.
Thanks to Wu Hao for a draft implementation of this infrastructure.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Samuel Ortiz <sameo@rivosinc.com>
Co-developed-by: Alexey Kardashevskiy <aik@amd.com>
Signed-off-by: Alexey Kardashevskiy <aik@amd.com>
Co-developed-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251031212902.2256310-8-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for adding more host bridge sysfs attributes, document the
existing naming format and 'firmware_node' attribute.
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251031212902.2256310-7-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
PCIe r7.0 Section 7.7.9 Device 3 Extended Capability Structure, defines the
canonical location for determining the Flit Mode of a device. This status
is a dependency for PCIe IDE enabling. Add a new fm_enabled flag to 'struct
pci_dev'.
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Samuel Ortiz <sameo@rivosinc.com>
Cc: Alexey Kardashevskiy <aik@amd.com>
Cc: Xu Yilun <yilun.xu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251031212902.2256310-6-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The PCIe 7.0 specification, section 11, defines the Trusted Execution
Environment (TEE) Device Interface Security Protocol (TDISP). This
protocol definition builds upon Component Measurement and Authentication
(CMA), and link Integrity and Data Encryption (IDE). It adds support for
assigning devices (PCI physical or virtual function) to a confidential VM
such that the assigned device is enabled to access guest private memory
protected by technologies like Intel TDX, AMD SEV-SNP, RISCV COVE, or ARM
CCA.
The "TSM" (TEE Security Manager) is a concept in the TDISP specification
of an agent that mediates between a "DSM" (Device Security Manager) and
system software in both a VMM and a confidential VM. A VMM uses TSM ABIs
to setup link security and assign devices. A confidential VM uses TSM
ABIs to transition an assigned device into the TDISP "RUN" state and
validate its configuration. From a Linux perspective the TSM abstracts
many of the details of TDISP, IDE, and CMA. Some of those details leak
through at times, but for the most part TDISP is an internal
implementation detail of the TSM.
CONFIG_PCI_TSM adds an "authenticated" attribute and "tsm/" subdirectory
to pci-sysfs. Consider that the TSM driver may itself be a PCI driver.
Userspace can watch for the arrival of a "TSM" device,
/sys/class/tsm/tsm0/uevent KOBJ_CHANGE, to know when the PCI core has
initialized TSM services.
The operations that can be executed against a PCI device are split into
two mutually exclusive operation sets, "Link" and "Security" (struct
pci_tsm_{link,security}_ops). The "Link" operations manage physical link
security properties and communication with the device's Device Security
Manager firmware. These are the host side operations in TDISP. The
"Security" operations coordinate the security state of the assigned
virtual device (TDI). These are the guest side operations in TDISP.
Only "link" (Secure Session and physical Link Encryption) operations are
defined at this stage. There are placeholders for the device security
(Trusted Computing Base entry / exit) operations.
The locking allows for multiple devices to be executing commands
simultaneously, one outstanding command per-device and an rwsem
synchronizes the implementation relative to TSM registration/unregistration
events.
Thanks to Wu Hao for his work on an early draft of this support.
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Samuel Ortiz <sameo@rivosinc.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Alexey Kardashevskiy <aik@amd.com>
Co-developed-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Link: https://patch.msgid.link/20251031212902.2256310-5-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
PCI/TSM, the PCI core functionality for the PCIe TEE Device Interface
Security Protocol (TDISP), has a need to walk all subordinate functions of
a Device Security Manager (DSM) to setup a device security context. A DSM
is physical function 0 of multi-function or SR-IOV device endpoint, or it
is an upstream switch port.
In error scenarios or when a TEE Security Manager (TSM) device is removed
it needs to unwind all established DSM contexts.
Introduce reverse versions of PCI device iteration helpers to mirror the
setup path and ensure that dependent children are handled before parents.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Link: https://patch.msgid.link/20251031212902.2256310-4-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link encryption is a new PCIe feature enumerated by "PCIe r7.0 section
7.9.26 IDE Extended Capability".
It is both a standalone port + endpoint capability, and a building block
for the security protocol defined by "PCIe r7.0 section 11 TEE Device
Interface Security Protocol (TDISP)". That protocol coordinates device
security setup between a platform TSM (TEE Security Manager) and a
device DSM (Device Security Manager). While the platform TSM can
allocate resources like Stream ID and manage keys, it still requires
system software to manage the IDE capability register block.
Add register definitions and basic enumeration in preparation for
Selective IDE Stream establishment. A follow on change selects the new
CONFIG_PCI_IDE symbol. Note that while the IDE specification defines
both a point-to-point "Link Stream" and a Root Port to endpoint
"Selective Stream", only "Selective Stream" is considered for Linux as
that is the predominant mode expected by Trusted Execution Environment
Security Managers (TSMs), and it is the security model that limits the
number of PCI components within the TCB in a PCIe topology with
switches.
Co-developed-by: Alexey Kardashevskiy <aik@amd.com>
Signed-off-by: Alexey Kardashevskiy <aik@amd.com>
Co-developed-by: Xu Yilun <yilun.xu@linux.intel.com>
Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexey Kardashevskiy <aik@amd.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Link: https://patch.msgid.link/20251031212902.2256310-3-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A "TSM" is a platform component that provides an API for securely
provisioning resources for a confidential guest (TVM) to consume. The
name originates from the PCI specification for platform agent that
carries out operations for PCIe TDISP (TEE Device Interface Security
Protocol).
Instances of this core device are parented by a device representing the
platform security function like CONFIG_CRYPTO_DEV_CCP or
CONFIG_INTEL_TDX_HOST.
This device interface is a frontend to the aspects of a TSM and TEE I/O
that are cross-architecture common. This includes mechanisms like
enumerating available platform TEE I/O capabilities and provisioning
connections between the platform TSM and device DSMs (Device Security
Manager (TDISP)).
For now this is just the scaffolding for registering a TSM device sysfs
interface.
Cc: Xu Yilun <yilun.xu@linux.intel.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Co-developed-by: Aneesh Kumar K.V (Arm) <aneesh.kumar@kernel.org>
Signed-off-by: Aneesh Kumar K.V (Arm) <aneesh.kumar@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alexey Kardashevskiy <aik@amd.com>
Link: https://patch.msgid.link/20251031212902.2256310-2-dan.j.williams@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
SMEM_IMAGE_VERSION_TABLE contains the version of the first 32 images.
Add images beyond that and read these from SMEM_IMAGE_VERSION_TABLE_2.
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251031-image-crm-part2-v2-2-c224c45c381a@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
When a SMEM item is allocated or retrieved, sanity check on the SMEM item
is performed and backtrace is printed if it is invalid. But there is no
benefit in dumping that information in the logs. Lets drop it.
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251031-image-crm-part2-v2-1-c224c45c381a@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
NSS clock controller is needed for supplying clocks and resets to the
networking blocks for the Ethernet functions on the IPQ5424 platforms.
All boards based on the IPQ5424 SoC will require this driver to be enabled.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://lore.kernel.org/r/20251014-qcom_ipq5424_nsscc-v7-10-081f4956be02@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the ubwc configuration for Kaanapali chipset. This chipset brings
support for UBWC v6 version. The rest of the configurations remains
as usual.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-kaana-gpu-support-v1-1-73530b0700ed@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Oleksij Rempel says:
====================
ethtool: introduce PHY MSE diagnostics UAPI and drivers
This series introduces a generic kernel-userspace API for retrieving PHY
Mean Square Error (MSE) diagnostics, together with netlink integration,
a fast-path reporting hook in LINKSTATE_GET, and initial driver
implementations for the KSZ9477 and DP83TD510E PHYs.
MSE is defined by the OPEN Alliance "Advanced diagnostic features for
100BASE-T1 automotive Ethernet PHYs" specification [1] as a measure of
slicer error rate, typically used internally to derive the Signal
Quality Indicator (SQI). While SQI is useful as a normalized quality
index, it hides raw measurement data, varies in scaling and thresholds
between vendors, and may not indicate certain failure modes - for
example, cases where autonegotiation would fail even though SQI reports
a good link. In practice, such scenarios can only be investigated in
fixed-link mode; here, MSE can provide an empirically estimated value
indicating conditions under which autonegotiation would not succeed.
Example output with current implementation:
root@DistroKit:~ ethtool lan1
Settings for lan1:
...
Speed: 1000Mb/s
Duplex: Full
...
Link detected: yes
SQI: 5/7
MSE: 3/127 (channel: worst)
root@DistroKit:~ ethtool --show-mse lan1
MSE diagnostics for lan1:
MSE Configuration:
Max Average MSE: 127
Refresh Rate: 2000000 ps
Symbols per Sample: 250
Supported capabilities: average channel-a channel-b channel-c
channel-d worst
MSE Snapshot (Channel: a):
Average MSE: 4
MSE Snapshot (Channel: b):
Average MSE: 3
MSE Snapshot (Channel: c):
Average MSE: 2
MSE Snapshot (Channel: d):
Average MSE: 3
[1] https://opensig.org/wp-content/uploads/2024/01/Advanced_PHY_features_for_automotive_Ethernet_V1.0.pdf
====================
Link: https://patch.msgid.link/20251027122801.982364-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement get_mse_capability() and get_mse_snapshot() for the DP83TD510E
to expose its Mean Square Error (MSE) register via the new PHY MSE
UAPI.
The DP83TD510E does not document any peak MSE values; it only exposes
a single average MSE register used internally to derive SQI. This
implementation therefore advertises only PHY_MSE_CAP_AVG, along with
LINK and channel-A selectors. Scaling is fixed to 0xFFFF, and the
refresh interval/number of symbols are estimated from 10BASE-T1L
symbol rate (7.5 MBd) and typical diagnostic intervals (~1 ms).
For 10BASE-T1L deployments, SQI is a reliable indicator of link
modulation quality once the link is established, but it does not
indicate whether autonegotiation pulses will be correctly received
in marginal conditions. MSE provides a direct measurement of slicer
error rate that can be used to evaluate if autonegotiation is likely
to succeed under a given cable length and condition. In practice,
testing such scenarios often requires forcing a fixed-link setup to
isolate MSE behaviour from the autonegotiation process.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251027122801.982364-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the get_mse_capability() and get_mse_snapshot() PHY driver ops
for KSZ9477-series integrated PHYs to demonstrate the new PHY MSE
UAPI.
These PHYs do not expose a documented direct MSE register, but the
Signal Quality Indicator (SQI) registers are derived from the
internal MSE computation. This hook maps SQI readings into the MSE
interface so that tooling can retrieve the raw value together with
metadata for correct interpretation in userspace.
Behaviour:
- For 1000BASE-T, report per-channel (A–D) values and support a
WORST channel selector.
- For 100BASE-TX, only LINK-wide measurements are available.
- Report average MSE only, with a max scale based on
KSZ9477_MMD_SQI_MASK and a fixed refresh rate of 2 µs.
This mapping differs from the OPEN Alliance SQI definition, which
assigns thresholds such as pre-fail indices; the MSE interface
instead provides the raw measurement, leaving interpretation to
userspace.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251027122801.982364-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the userspace entry point for PHY MSE diagnostics via
ethtool netlink. This exposes the core API added previously and
returns both capability information and one or more snapshots.
Userspace sends ETHTOOL_MSG_MSE_GET. The reply carries:
- ETHTOOL_A_MSE_CAPABILITIES: scale limits and timing information
- ETHTOOL_A_MSE_CHANNEL_* nests: one or more snapshots (per-channel
if available, otherwise WORST, otherwise LINK)
Link down returns -ENETDOWN.
Changes:
- YAML: add attribute sets (mse, mse-capabilities, mse-snapshot)
and the mse-get operation
- UAPI (generated): add ETHTOOL_A_MSE_* enums and message IDs,
ETHTOOL_MSG_MSE_GET/REPLY
- ethtool core: add net/ethtool/mse.c implementing the request,
register genl op, and hook into ethnl dispatch
- docs: document MSE_GET in ethtool-netlink.rst
The include/uapi/linux/ethtool_netlink_generated.h is generated
from Documentation/netlink/specs/ethtool.yaml.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20251027122801.982364-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the base infrastructure for Mean Square Error (MSE) diagnostics,
as proposed by the OPEN Alliance "Advanced diagnostic features for
100BASE-T1 automotive Ethernet PHYs" [1] specification.
The OPEN Alliance spec defines only average MSE and average peak MSE
over a fixed number of symbols. However, other PHYs, such as the
KSZ9131, additionally expose a worst-peak MSE value latched since the
last channel capture. This API accounts for such vendor extensions by
adding a distinct capability bit and snapshot field.
Channel-to-pair mapping is normally straightforward, but in some cases
(e.g. 100BASE-TX with MDI-X resolution unknown) the mapping is ambiguous.
If hardware does not expose MDI-X status, the exact pair cannot be
determined. To avoid returning misleading per-channel data in this case,
a LINK selector is defined for aggregate MSE measurements.
All investigated devices differ in MSE capabilities, such
as sample rate, number of analyzed symbols, and scaling factors.
For example, the KSZ9131 uses different scaling for MSE and pMSE.
To make this visible to callers, scale limits and timing information
are returned via get_mse_capability().
Some PHYs sample very few symbols at high frequency (e.g. 2 us update
rate). To cover such cases and allow for future high-speed PHYs with
even shorter intervals, the refresh rate is reported as u64 in
picoseconds.
This patch introduces the internal PHY API for Mean Square Error
diagnostics. It defines new kernel-side data types and driver hooks:
- struct phy_mse_capability: describes supported metrics, scale
limits, update interval, and sampling length.
- struct phy_mse_snapshot: holds one correlated measurement set.
- New phy_driver ops: `get_mse_capability()` and `get_mse_snapshot()`.
These definitions form the core kernel API. No user-visible interfaces
are added in this commit.
Standardization notes:
OPEN Alliance defines presence and interpretation of some metrics but does
not fix numeric scales or sampling internals:
- SQI (3-bit, 0..7) is mandatory; correlation to SNR/BER is informative
(OA 100BASE-T1 TC1 v1.0 6.1.2; OA 1000BASE-T1 TC12 v2.2 6.1.2).
- MSE is optional; OA recommends 2^16 symbols and scaling to 0..511,
with a worst-case latch since last read (OA 100BASE-T1 TC1 v1.0 6.1.1; OA
1000BASE-T1 TC12 v2.2 6.1.1). Refresh is recommended (~0.8-2.0 ms for
100BASE-T1; ~80-200 us for 1000BASE-T1). Exact scaling/time windows
are vendor-specific.
- Peak MSE (pMSE) is defined only for 100BASE-T1 as optional, e.g.
128-symbol sliding window with 8-bit range and worst-case latch (OA
100BASE-T1 TC1 v1.0 6.1.3).
Therefore this API exposes which measures and selectors a PHY supports,
and documents where behavior is standard-referenced vs vendor-specific.
[1] <https://opensig.org/wp-content/uploads/2024/01/
Advanced_PHY_features_for_automotive_Ethernet_V1.0.pdf>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251027122801.982364-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>