Currently ethtool shows lbrx_packets and lbrx_bytes (Good RX
Packets/Octets loopback Count), but doesn't show the TX-side equivalents
(lbtx_packets and lbtx_bytes). Add visibility of those missing
statistics by adding them to ethtool statistics.
In addition, the order of lbrx_bytes and lbrx_packets is not consistent
with non-loopback statistics (rx_packets, rx_bytes). Therefore,
align the order by swapping positions of lbrx_bytes and lbrx_packets.
Tested on Intel Corporation I350 Gigabit Network Connection.
Before:
# ethtool -S ens5 | grep -E "x_(bytes|packets)"
rx_packets: 135
tx_packets: 106
rx_bytes: 16010
tx_bytes: 12451
lbrx_bytes: 1148
lbrx_packets: 12
After:
# ethtool -S ens5 | grep -E "x_(bytes|packets)"
rx_packets: 748
tx_packets: 304
rx_bytes: 81513
tx_bytes: 33698
lbrx_packets: 97
lbtx_packets: 109
lbrx_bytes: 12090
lbtx_bytes: 12401
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, during locating the CIVD section, the ixgbe driver loops
over the OROM area and at each iteration reads only OROM-datastruct-size
amount of data. This results in many small reads and is inefficient.
Optimize this by reading the entire OROM bank into memory once before
entering the loop. This significantly reduces the probing time.
Without this patch probing time may exceed over 25s, whereas with this
patch applied average time of probe is not greater than 5s.
without the patch:
[14:12:22] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[14:12:25] ixgbe 0000:21:00.0: Multiqueue Enabled: Rx Queue count = 63, Tx Queue count = 63 XDP Queue count = 0
[14:12:25] ixgbe 0000:21:00.0: 63.012 Gb/s available PCIe bandwidth (16.0 GT/s PCIe x4 link)
[14:12:26] ixgbe 0000:21:00.0: MAC: 7, PHY: 27, PBA No: N55484-001
[14:12:26] ixgbe 0000:21:00.0: 20:3a:43:09:3a:12
[14:12:26] ixgbe 0000:21:00.0: Intel(R) 10 Gigabit Network Connection
[14:12:50] ixgbe 0000:21:00.0 ens2f0np0: renamed from eth0
with the patch:
[14:18:18] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[14:18:19] ixgbe 0000:21:00.0: Multiqueue Enabled: Rx Queue count = 63, Tx Queue count = 63 XDP Queue count = 0
[14:18:19] ixgbe 0000:21:00.0: 63.012 Gb/s available PCIe bandwidth (16.0 GT/s PCIe x4 link)
[14:18:19] ixgbe 0000:21:00.0: MAC: 7, PHY: 27, PBA No: N55484-001
[14:18:19] ixgbe 0000:21:00.0: 20:3a:43:09:3a:12
[14:18:19] ixgbe 0000:21:00.0: Intel(R) 10 Gigabit Network Connection
[14:18:22] ixgbe 0000:21:00.0 ens2f0np0: renamed from eth0
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The auto-negotiation limitation for 2.5G and 5G speeds is no longer true
for X550 successors like E610 adapter. Enable the 2.5G and 5G speeds in
auto-negotiation for E610 at driver load.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
WLAN Host driver interacts with the Firmware and vice versa using
Host-To-Target (HTT) interface.
Relocate HTT specific code from dp_tx.c to dp_htt.c introduced for
HTT interface. These code is compiled as part of the common module
ath12k.ko.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harsh Kumar Bijlani <quic_hbijlani@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-20-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WLAN Host driver interacts with the Firmware and vice versa using
Host-To-Target (HTT) interface.
HTT interface code is spread across multiple files (ex dp_tx.c, dp_rx.c
etc) and this interface is independent of the underlying architecture Tx
and Rx. Relocate HTT specific code from dp_rx.c to newly introduced file
dp_htt.c for HTT interface. This new file is compiled as part of the
common module ath12k.ko.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harsh Kumar Bijlani <quic_hbijlani@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-19-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WLAN Host driver interacts with the Firmware and vice versa using
Host-To-Target (HTT) interface.
HTT interface code is spread across multiple files (ex dp_tx.c,
dp_rx.c, dp.h etc) and this interface is independent of the underlying
architecture Tx and Rx.
Relocate HTT specific code from dp.h to newly introduced file dp_htt.h
for HTT interface.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harsh Kumar Bijlani <quic_hbijlani@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-18-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move arch specific TX data path to wifi7 directory as part of Next
Generation (NG) Driver Framework.
Architecture specific APIs:
ath12k_hal_tx_cmd_ext_desc_setup
ath12k_dp_prepare_htt_metadata
ath12k_dp_tx
The moved APIs will be a part of dp_tx.c file inside wifi7 directory.
wifi7/dp_tx.c file will continue to be part of ath12k.ko temporarily
until the corresponding infra for movement to ath12k_wifi7.ko arrives
in upcoming patches.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-17-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move arch specific TX data path to wifi7 directory as part of Next
Generation (NG) Driver Framework.
Architecture specific APIs:
ath12k_dp_tx_htt_tx_complete_buf
ath12k_dp_tx_process_htt_tx_complete
ath12k_dp_tx_update_txcompl
ath12k_dp_tx_complete_msdu
ath12k_dp_tx_status_parse
ath12k_dp_tx_completion_handler
The moved APIs will be a part of dp_tx.c file inside wifi7 directory.
wifi7/dp_tx.c file will continue to be part of ath12k.ko temporarily
until the corresponding infra for movement to ath12k_wifi7.ko arrives
in upcoming patches.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-16-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move arch specific Rx tid related functions to wifi7 directory.
The moved APIs will be a part of dp_rx.c file inside wifi7 directory.
wifi7/dp_rx.c file will continue to be part of ath12k.ko
temporarily until the corresponding infra for movement
to ath12k_wifi7.ko arrives in upcoming patches.
Architecture specific APIs:
ath12k_peer_rx_tid_qref_reset
ath12k_dp_reo_cache_flush
ath12k_dp_reo_cmd_send
ath12k_peer_rx_tid_reo_update
ath12k_dp_rx_link_desc_return
ath12k_dp_rx_peer_tid_delete
ath12k_peer_rx_tid_qref_setup
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-15-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move arch specific REO functions to wifi7 directory.
The moved APIs will be a part of dp_rx.c file inside wifi7 directory.
wifi7/dp_rx.c file will continue to be part of ath12k.ko temporarily
until the corresponding infra for movement to ath12k_wifi7.ko arrives
in upcoming patches.
Architecture specific APIs:
ath12k_dp_setup_pn_check_reo_cmd
ath12k_dp_rx_assign_reoq
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-14-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Below API have architecture specific HAL macros.
ath12k_dp_rx_peer_pn_replay_config
Separate architecture specific parts from these APIs to
later move them to wifi7 directory.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-13-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move ath12k_dp_service_srng API and ath12k_dp_rx_process_reo_status
to wifi7 directory.
As srng processing is specific to architecture (wifi7 / wifi8), the
API ath12k_dp_service_srng is being moved to wifi7 directory. The
file wifi7/dp.c can be used to define wifi7-specifi functions that are
common to both tx and rx.
The API which is invoked as part of service srng,
ath12k_dp_rx_process_reo_status is also moved to wifi7 directory, as
the implementation is specific to HW due to the usage of wifi7
specific HAL macros.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-12-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move arch specific RX MSDU processing related functions to wifi7 directory.
The moved APIs will be a part of dp_rx.c file inside wifi7 directory.
wifi7/dp_rx.c file will continue to be part of ath12k.ko temporarily
until the corresponding infra for movement to ath12k_wifi7.ko arrives
in upcoming patches.
Architecture specific APIs:
ath12k_dp_rx_msdu_coalesce
ath12k_dp_rx_h_csum_offload
ath12k_dp_rx_h_mpdu
ath12k_dp_rx_process
ath12k_dp_rx_process_received_packets
ath12k_dp_rx_h_verify_tkip_mic
ath12k_dp_rx_process_msdu
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-11-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move arch specific RX error and defrag functions to wifi7 directory.
The moved APIs will be a part of dp_rx.c file inside wifi7 directory.
wifi7/dp_rx.c file will continue to be part of ath12k.ko
temporarily until the corresponding infra for movement
to ath12k_wifi7.ko arrives in upcoming patches.
Architecture specific APIs:
ath12k_dp_rx_h_defrag_validate_incr_pn
ath12k_dp_rx_h_defrag_reo_reinject
ath12k_dp_rx_h_defrag
ath12k_dp_rx_frag_h_mpdu
ath12k_dp_process_rx_err_buf
ath12k_dp_rx_process_err
ath12k_dp_rx_null_q_desc_sg_drop
ath12k_dp_rx_h_null_q_desc
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-10-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move architecture specific RxDMA functions to wifi7 directory.
The moved APIs will be a part of dp_rx.c file inside wifi7 directory.
wifi7/dp_rx.c file will continue to be part of ath12k.ko temporarily
until the corresponding infra for movement to ath12k_wifi7.ko arrives
in upcoming patches.
Architecture specific APIs:
ath12k_dp_rxdma_ring_sel_config_qcn9274
ath12k_dp_rxdma_ring_sel_config_wcn7850
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-9-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move wifi7 architecture specific file rx_desc.h to wifi7 directory
and rename it to hal_rx_desc.h to match the naming convention used,
and move the common part from it to hal.h file which is in the
common directory.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-8-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move wifi7 architecture specific file hal_desc.h to wifi7 directory,
and move the common part from it to hal.h file which is in the
common directory.
It is as part of a broader effort to separate common and hardware-specific
code into distinct modules. This modularization enables reuse of the common
driver components across multiple hardware architectures.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-7-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move wifi7 architecture specific Rx error functions from dp_rx.c to
wifi7 directory.
The new wifi7-specific dp_rx.c file will continue to be part of ath12k.ko
temporarily until the corresponding infra for movement to the
ath12k_wifi7.ko arrives in upcoming patches.
Move following architecture specific APIs to wifi7 directory:
ath12k_dp_rx_h_tkip_mic_err
ath12k_dp_rx_h_rxdma_err
ath12k_dp_rx_h_reo_err
ath12k_dp_rx_wbm_err
ath12k_dp_rx_process_wbm_err
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-6-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move wifi7 architecture specific file hal_rx.h to wifi7 directory, and move
the common part from it to hal.h file which is in the common directory.
It is as part of a broader effort to separate common and hardware-specific
code into distinct modules. This modularization enables reuse of the common
driver components across multiple hardware architectures.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-4-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move wifi7 architecture specific file hal_tx.h to wifi7 directory, and move
the common part from it to hal.h file which is in the common directory.
It is as part of a broader effort to separate common and hardware-specific
code into distinct modules. This modularization enables reuse of the common
driver components across multiple hardware architectures.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-3-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Move architecture-specific files hal_rx.c and hal_tx.c into the wifi7
directory as part of a broader effort to separate common and hardware
-specific code into distinct modules. This modularization enables reuse
of the common driver components across multiple hardware architectures.
The relocated files remain part of ath12k.ko temporarily, until the
corresponding infra for movement to the ath12k_wifi7.ko arrives in
upcoming patches.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pavankumar Nandeshwar <quic_pnandesh@quicinc.com>
Signed-off-by: Ripan Deuri <quic_rdeuri@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20250828173553.3341351-2-quic_rdeuri@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The SDMMC in this IP currently only supports legacy mode
due to a hardware quirk, setting the flags to reflect the limitation.
Fixes: deaa14ab6b ("ARM: dts: microchip: add support for sama7d65_curiosity board")
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20250819170528.126010-1-Ryan.Wanner@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Like with the ARM64 Microchip platforms, lets add a generic ARCH_MICROCHIP
symbol and select it so that drivers that are reused for multiple product
generation or lines, can just depend on it instead of adding each SoC
symbol as their dependencies.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Daniel Machon <daniel.machon@microchip.com>
Link: https://lore.kernel.org/r/20250813174720.540015-3-robert.marko@sartura.hr
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Add the hdp devicetree node for stm32mp15 SoC family
Keep the node disabled as HDP needs the pinctrl SoC configuration to be
able to output its mux output signal outside of the SoC, on the SoC pad.
This configuration is provided in the board dtsi file through 'pinctrl-*'
properties as well as HDP mux configuration.
Thus, if needed, HDP should be enabled in board dtsi file.
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Link: https://lore.kernel.org/r/20250711-hdp-upstream-v7-5-faeecf7aaee1@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add the hdp devicetree node for stm32mp13 SoC family.
Keep the node disabled as HDP needs the pinctrl SoC configuration to be
able to output its mux output signal outside of the SoC, on the SoC pad.
This configuration is provided in the board dtsi file through 'pinctrl-*'
properties as well as HDP mux configuration.
Thus, if needed, HDP should be enabled in board dtsi file.
Signed-off-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Link: https://lore.kernel.org/r/20250711-hdp-upstream-v7-4-faeecf7aaee1@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add to the node m4_rproc the pinctrl property corresponding to the
orange LED.
The GPIO is reserved for the coprocessor Cortex-M4 and will be
ignored by Linux.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Link: https://lore.kernel.org/r/20250610152309.299438-5-antonio.borneo@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO H7 on boards stm32mp15xx-dkx and the GPIO D8 on boards
stm32mp15xx-ed1 are used by the coprocessor Cortex-M4.
Linux running on Cortex-A should not use the GPIO and should left
it available for the coprocessor.
Add two pinmux groups, one for each families of boards, setting
the GPIO function as Reserved (RSVD).
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Link: https://lore.kernel.org/r/20250610152309.299438-4-antonio.borneo@foss.st.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Move startup code out of the __head section, now that this no longer has
a special significance. Move everything into .text or .init.text as
appropriate, so that startup code is not kept around unnecessarily.
[ bp: Fold in hunk to fix 32-bit CPU hotplug:
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202509022207.56fd97f4-lkp@intel.com ]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-45-ardb+git@google.com
Recent EFI x86 systems are more strict when it comes to mapping boot
images, and require that mappings are either read-write or read-execute.
Now that the boot code is being cleaned up and refactored, most of it is
being moved into .init.text [where it arguably belongs] but that implies
that when booting on such strict EFI firmware, we need to take care to
map .init.text (and the .altinstr_aux section that follows it)
read-execute as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-44-ardb+git@google.com
In order to be able to have tight control over which code may execute
from the early 1:1 mapping of memory, but still link vmlinux as a single
executable, prefix all symbol references in startup code with __pi_, and
invoke it from outside using the __pi_ prefix.
Use objtool to check that no absolute symbol references are present in
the startup code, as these cannot be used from code running from the 1:1
mapping.
Note that this also requires disabling the latent-entropy GCC plugin, as
the global symbol references that it injects would require explicit
exports, and given that the startup code rarely executes more than once,
it is not a useful source of entropy anyway.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-43-ardb+git@google.com
Using core-y is not the correct way to get kbuild to descend into
arch/x86/boot/startup. For instance, building an individual object does
not work as expected when the pattern rule is local to the Makefile
$ make arch/x86/boot/startup/map_kernel.pi.o
GEN Makefile
CALL /home/ardb/linux/scripts/checksyscalls.sh
DESCEND objtool
INSTALL libsubcmd_headers
make[3]: *** No rule to make target 'arch/x86/boot/startup/map_kernel.pi.o'. Stop.
make[2]: *** [/home/ardb/linux/scripts/Makefile.build:461: arch/x86] Error 2
make[1]: *** [/home/ardb/linux/Makefile:2011: .] Error 2
make: *** [/home/ardb/linux/Makefile:248: __sub-make] Error 2
So use obj-y from arch.x86/Kbuild instead, which makes things work as
expected.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-42-ardb+git@google.com
This reverts commit
faf0ed4874 ("x86/boot: Reject absolute references in .head.text")
The startup code is checked directly for the absence of absolute symbol
references, so checking the .head.text section in the relocs tool is no
longer needed.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-41-ardb+git@google.com
Invoke objtool on each startup code object individually to check for the
absence of absolute relocations. This is needed because this code will
be invoked from the 1:1 mapping of memory before those absolute virtual
addresses (which are derived from the kernel virtual base address
provided to the linker and possibly shifted at boot) are mapped.
Only objects built under arch/x86/boot/startup/ have this restriction,
and once they have been incorporated into vmlinux.o, this distinction is
difficult to make. So force the invocation of objtool for each object
file individually, even if objtool is deferred to vmlinux.o for the rest
of the build. In the latter case, only pass --noabs and nothing else;
otherwise, append it to the existing objtool command line.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-40-ardb+git@google.com
The x86 startup code must not use absolute references to code or data,
as it executes before the kernel virtual mapping is up.
Add an action to objtool to check all allocatable sections (with the
exception of __patchable_function_entries, which uses absolute
references for nebulous reasons) and raise an error if any absolute
references are found.
Note that debug sections typically contain lots of absolute references
too, but those are not allocatable so they will be ignored.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/20250828102202.1849035-39-ardb+git@google.com
Create aliases that expose routines that are part of the startup code to
other code in the core kernel, so that they can be called later as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-38-ardb+git@google.com
Rename sev-nmi.c to noinstr.c, and move the get/put GHCB routines into it too,
which are also annotated as 'noinstr' and suffer from the same problem as the
NMI code, i.e., that GCC may ignore the __no_sanitize_address__ function
attribute implied by 'noinstr' and insert KASAN instrumentation anyway.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-37-ardb+git@google.com
Provide PIC aliases for data objects that are shared between the SEV startup
code and the SEV code that executes later. This is needed so that the confined
startup code is permitted to access them.
This requires some of these variables to be moved into a source file that is
not part of the startup code, as the PIC alias is already implied, and
exporting variables in the opposite direction is not supported.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-36-ardb+git@google.com
Provide PIC aliases for the global variables related to 5-level paging, so
that the startup code can access them in order to populate the kernel page
tables.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-35-ardb+git@google.com
snp_vmpl will be assigned a non-zero value when executing at a VMPL other than
0, and this is inferred from a call to RMPADJUST, which only works when
running at VMPL0.
This means that testing snp_vmpl is sufficient, and there is no need to
perform the same check again.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-34-ardb+git@google.com
To avoid having to reason about whether or not to use the per-CPU SVSM calling
area when running startup and init code on the boot CPU, reuse the boot SVSM
calling area as the per-CPU area for the BSP.
Thus, remove the need to make the per-CPU variables and associated state in
sev_cfg accessible to the startup code once confined.
[ bp: Massage commit message. ]
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-33-ardb+git@google.com
The early page state change API is mostly only used very early, when only the
boot time SVSM calling area is in use. However, this API is also called by the
kexec finishing code, which runs very late, and potentially from a different
CPU (which uses a different calling area).
To avoid pulling the per-CPU SVSM calling area pointers and related SEV state
into the startup code, refactor the page state change API so the SVSM calling
area virtual and physical addresses can be provided by the caller.
No functional change intended.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-32-ardb+git@google.com
Both the decompressor and the SEV startup code implement the exact same
sequence for invoking the MSR based communication protocol to effectuate
a page state change.
Before tweaking the internal APIs used in both versions, merge them and
share them so those tweaks are only needed in a single place.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-31-ardb+git@google.com
The boottime SVSM calling area is used both by the startup code running from
a 1:1 mapping, and potentially later on running from the ordinary kernel
mapping.
This SVSM calling area is statically allocated, and so its physical address
doesn't change. However, its virtual address depends on the calling context
(1:1 mapping or kernel virtual mapping), and even though the variable that
holds the virtual address of this calling area gets updated from 1:1 address
to kernel address during the boot, it is hard to reason about why this is
guaranteed to be safe.
So instead, take the RIP-relative address of the boottime SVSM calling area
whenever its virtual address is required, and only use a global variable for
the physical address.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/20250828102202.1849035-30-ardb+git@google.com
Both the decompressor and the core kernel implement an early #VC handler,
which only deals with CPUID instructions, and full featured one, which can
handle any #VC exception.
The former communicates with the hypervisor using the MSR based protocol,
whereas the latter uses a shared GHCB page, which is configured a bit later
during the boot, when the kernel runs from its ordinary virtual mapping,
rather than the 1:1 mapping that the startup code uses.
Accessing this shared GHCB page from the core kernel's startup code is
problematic, because it involves converting the GHCB address provided by the
caller to a physical address. In the startup code, virtual to physical address
translations are problematic, given that the virtual address might be a 1:1
mapped address, and such translations should therefore be avoided.
This means that exposing startup code dealing with the GHCB to callers that
execute from the ordinary kernel virtual mapping should be avoided too. So
move all GHCB page based communication out of the startup code, now that all
communication occurring before the kernel virtual mapping is up relies on the
MSR protocol only.
As an exception, add a flag representing the need to apply the coherency
fix in order to avoid exporting CPUID* helpers because of the code
running too early for the *cpu_has* infrastructure.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/20250828102202.1849035-29-ardb+git@google.com
The "if" condition is also part of the "while" condition, remove the
"if" to reduce the amount of code.
Reported-by: Howard Chu <howardchu95@gmail.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Chun-Tse Shao <ctshao@google.com>
Cc: Collin Funk <collin.funk1@gmail.com>
Cc: Dr. David Alan Gilbert <linux@treblig.org>
Cc: Gautam Menghani <gautam@linux.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Falcon <thomas.falcon@intel.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Weilin Wang <weilin.wang@intel.com>
Cc: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250819013941.209033-12-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Change tree nodes to having a value of either Metric or PmuEvent,
these values have the ability to match searches, be parsed to create
evlists and to give a value per CPU and per thread to display.
Use perf.metrics to generate a tree of metrics. Most metrics are placed
under their metric group, if the metric group name ends with '_group'
then the metric group is placed next to the associated metric.
Reviewed-by: Howard Chu <howardchu95@gmail.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Chun-Tse Shao <ctshao@google.com>
Cc: Collin Funk <collin.funk1@gmail.com>
Cc: Dr. David Alan Gilbert <linux@treblig.org>
Cc: Gautam Menghani <gautam@linux.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Falcon <thomas.falcon@intel.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Weilin Wang <weilin.wang@intel.com>
Cc: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250819013941.209033-11-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>