Compute base inside intel_pinctrl_probe_pwm() only after the
PINCTRL_FEATURE_PWM and CONFIG_PWM_LPSS checks have passed. Tidy
up; no functional change.
Suggested-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/linux-gpio/aglu5jy5SbW9Wjwj@ashevche-desk.local/
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
By convention MODULE_DEVICE_TABLE() immediately follows the ID table it
exports, because this is easier to read and verify. It also makes more
sense since #ifdef for ACPI or OF could hide both of them.
Most of the privers already have this correctly placed, so adjust
the missing ones. No functional impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add &mac0, &mdio3, and the ethphy3 PHY node to enable BMC networking
on the AST2600-based NVIDIA MSX4 board. The PHY is attached to MDIO3
at address 2 and uses RGMII with PHY-internal delays.
These nodes were intentionally omitted in commit f28674fab3 ("ARM:
dts: aspeed: Add NVIDIA MSX4 HPM") at Andrew Lunn's request, pending
clarification of the RGMII delay handling. Following his guidance on
linux-aspeed, the bootloader has been modified to stop enabling MAC
clock delays on the SoC side, so phy-mode = "rgmii-id" correctly
results in the PHY adding the required ~2ns delay without any
double-delay from the MAC controller.
The corresponding U-Boot change has been submitted to openbmc/u-boot.
Link: https://patch.msgid.link/eac09481-0ba1-4ac2-ad8c-d859822ff0d5@lunn.ch
Link: https://patch.msgid.link/20260504044702.2613879-1-andhsieh@nvidia.com
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Marc Olberding <molberding@nvidia.com>
Signed-off-by: Ender Hsieh <andhsieh@nvidia.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
- tegra:
- drop runtime PM reference when exiting on mutex_lock failure
- preserve transfer errors when releasing the mutex
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQScDfrjQa34uOld1VLaeAVmJtMtbgUCagbyLwAKCRDaeAVmJtMt
bu7nAQCvlINIxjjP8xHbD1IEzI/DMZP2fEdvqUgEqNjRQwYCaQD+OOD3D63q/c93
t4pvPCAdueFWfK1+MWOYsXPKVkHglQE=
=IYx9
-----END PGP SIGNATURE-----
Merge tag 'i2c-host-fixes-7.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
i2c-host-fixes for v7.1-rc4
- tegra:
- drop runtime PM reference when exiting on mutex_lock failure
- preserve transfer errors when releasing the mutex
In Xe3p there is an HW optimization done. When there is an SU triggered in
Capture state, Link will be kept ON post Capture CRC SDP. Before valid SU
pixels Intel source will transmit dummy pixels. Some TCONS are improperly
considering these dummy pixels as a valid pixel data. Prior Xe3p link was
was turned off even if there was SU triggered in capture state and no dummy
pixels were transmitted. These dummy pixels are problem only if SDP on
prior scanline is used and Early Transport is not in use. The workaround is
to start SU area always at scanline 0.
v2: use intel_display_wa
Bspec: 74741, 79482
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260515095756.2799483-5-jouni.hogander@intel.com
There is Intel specific workaround DPCD address containing workaround for
case where SDP is on prior line. Apply this workaround according to values
in the offset.
Fixes: 61e887329e ("drm/i915/xelpd: Handle PSR2 SDP indication in the prior scanline")
Cc: <stable@vger.kernel.org> # v5.15+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260515095756.2799483-4-jouni.hogander@intel.com
Read Intel DPCD workaround register and store it into
intel_connector->dp.psr_caps. psr_caps was chosen as currently it contains
only PSR workaround for PSR2 SDP on prior scanline implementation.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260515095756.2799483-3-jouni.hogander@intel.com
EDP specification says:
"If either VSC SDP is unable to be transmitted 100 ns before the SU region,
the Source device may optionally transmit the VSC SDP during the prior
video scan line’s HBlank period There is a Intel specific drm dp register
currently containing bits related how TCON can support PSR2 with SDP on
prior line."
Unfortunately many panels are having problems in implementing this. So
there is a custom Intel specific DPCD register (INTEL_WA_REGISTER_CAPS) to
figure out if this is properly implemented on a panel or if panel doesn't
require that 100 ns delay before the SU region. Here are the definitions in
this custom DPCD address:
0 = Panel doesn't support SDP on prior line
1 = Panel supports SDP on prior line
2 = Panel doesn't have 100ns requirement
3 = Reserved
Add definitions for this new register and it's values into new header
intel_dpcd.h.
v2: add INTEL_DPCD_ prefix to definitions
Bspec: 74741
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patch.msgid.link/20260515095756.2799483-2-jouni.hogander@intel.com
Add JTAG_CPLD_TRST_R_N to the sgpiom0 pin name table on Facebook Anacapa
BMC. This exposes the CPLD JTAG TRST signal through SGPIO, allowing
proper JTAG reset control during debug.
[arj: Minor tidying of commit message formatting]
Signed-off-by: Colin Huang <u8813345@gmail.com>
Link: https://patch.msgid.link/20260511-add-jtag-trst-pin-v1-1-b0be2f7b2da5@gmail.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
The HP Z66 G6 14 inch laptop uses the ALC236 codec with subsystem ID
0x103c:8df7. Without a quirk entry, the PCI SSID falls back to the
generic 0x103c:0000 fixup, which does not configure the mute/micmute
LED GPIOs correctly.
Add the SND_PCI_QUIRK entry for this model using
ALC236_FIXUP_HP_GPIO_LED, matching the surrounding HP EliteBook G12
entries (0x8dec-0x8dfe) which share the same ALC236 codec and GPIO LED
layout.
Signed-off-by: Minxi Hou <houminxi@gmail.com>
Link: https://patch.msgid.link/20260518031542.2899188-1-houminxi@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The kvm_riscv_vcpu_mmio_return() function handles MMIO read results
by writing the data back to the guest register. For signed load
instructions (LB, LH, LW on RV64), the value needs sign-extension
from a smaller integer to unsigned long.
The current code uses:
(ulong)data << shift >> shift
but (ulong) makes the right shift a logical shift (zero-extend)
rather than an arithmetic shift (sign-extend), causing incorrect
results when the MMIO device returns a negative value. For example,
LB reading 0x80 would return 128 instead of -128.
Fix this by casting to (long) after the left shift so that the
subsequent right shift is arithmetic and correctly propagates
the sign bit:
(long)((ulong)data << shift) >> shift
Additionally, remove the unnecessary shift assignment for LBU
(unsigned byte load) since it does not need sign extension.
This makes LBU consistent with LHU and LWU which already keep
shift = 0.
Fixes: b91f0e4cb8 ("RISC-V: KVM: Factor-out instruction emulation into separate sources")
Signed-off-by: Jiakai Xu <jiakaiPeanut@gmail.com>
Signed-off-by: Jiakai Xu <xujiakai2025@iscas.ac.cn>
Assisted-by: OpenClaw:DeepSeek-V3.2
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20260514081752.472987-1-xujiakai2025@iscas.ac.cn
Signed-off-by: Anup Patel <anup@brainfault.org>
The SBI v0.1 SEND_IPI handler iterates over the hart mask and calls
kvm_get_vcpu_by_id() to find the target vcpu for each set bit. When a
guest provides a hart mask containing bits for non-existent vcpu_ids,
kvm_get_vcpu_by_id() returns NULL, which is then unconditionally
dereferenced by kvm_riscv_vcpu_set_interrupt(), causing a kernel crash.
Fix this by adding a NULL check before dereferencing the return value.
If the target vcpu is not found, skip it and continue processing the
remaining valid harts.
Fixes: a046c2d857 ("RISC-V: KVM: Reorganize SBI code by moving SBI v0.1 to its own file")
Signed-off-by: Jiakai Xu <jiakaiPeanut@gmail.com>
Signed-off-by: Jiakai Xu <xujiakai2025@iscas.ac.cn>
Assisted-by: OpenClaw:DeepSeek-V3.2
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20260517124414.420919-1-xujiakai2025@iscas.ac.cn
Signed-off-by: Anup Patel <anup@brainfault.org>
kvm_riscv_vcpu_pmu_event_info() returned -ENOMEM from the
SBI extension handler, which caused kvm_riscv_vcpu_sbi_ecall()
to abort KVM_RUN and surface the error to userspace instead of
completing the ECALL with a negative SBI error in a0.
Use SBI_ERR_FAILURE and the normal retdata path, matching other PMU
handlers and kvm_sbi_ext_pmu_handler comment.
Fixes: e309fd113b ("RISC-V: KVM: Implement get event info function")
Cc: stable@vger.kernel.org
Signed-off-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20260514173642.41448-2-osama.abdelkader@gmail.com
Signed-off-by: Anup Patel <anup@brainfault.org>
kvm_riscv_vcpu_pmu_snapshot_set_shmem() returned -ENOMEM from the
SBI extension handler, which caused kvm_riscv_vcpu_sbi_ecall() to
abort KVM_RUN and surface the error to userspace instead of
ompleting the ECALL with a negative SBI error in a0.
Use SBI_ERR_FAILURE and the normal retdata path, matching other PMU
handlers and kvm_sbi_ext_pmu_handler comment.
Fixes: c2f41ddbcd ("RISC-V: KVM: Implement SBI PMU Snapshot feature")
Cc: stable@vger.kernel.org
Signed-off-by: Osama Abdelkader <osama.abdelkader@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20260514173642.41448-1-osama.abdelkader@gmail.com
Signed-off-by: Anup Patel <anup@brainfault.org>
kvm_riscv_vcpu_record_steal_time() assumes that the steal-time shared
memory GPA (vcpu->arch.sta.shmem) is always backed by a valid guest
memory slot. However, this assumption is not guaranteed by the KVM
userspace ABI.
A malicious or buggy userspace can set the STA shared memory GPA via
KVM_SET_ONE_REG without establishing a corresponding memory region via
KVM_SET_USER_MEMORY_REGION. In such cases, the GPA cannot be translated
to a valid HVA and kvm_vcpu_gfn_to_hva() returns an error address.
The current implementation incorrectly treats this as a kernel warning
using WARN_ON(), which may escalate to a kernel panic when panic_on_warn
is enabled.
This is not a kernel bug condition but a normal invalid configuration
from userspace, and should be handled gracefully.
Fix it by removing WARN_ON() and treating invalid HVA as a normal
failure case, resetting the STA shared memory state.
Fixes: e9f12b5fff ("RISC-V: KVM: Implement SBI STA extension")
Signed-off-by: Jiakai Xu <xujiakai2025@iscas.ac.cn>
Signed-off-by: Jiakai Xu <jiakaiPeanut@gmail.com>
Assisted-by: OpenClaw:DeepSeek-V3.2
Reviewed-by: Nutty Liu <nutty.liu@hotmail.com>
Reviewed-by: Andrew Jones <andrew.jones@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260415075216.2757427-1-xujiakai2025@iscas.ac.cn
Signed-off-by: Anup Patel <anup@brainfault.org>
Add the i3c controller devices to the ast2600 g6 common dts. We add all
6 busses to the common g6 definition, but leave disabled through the
status property, to be enabled per-platform.
Suggested-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Dawid Glazik <dawid.glazik@linux.intel.com>
Link: https://patch.msgid.link/7a94a5f4cf84c11c7fba7485e666ecbaddfbe5cf.1777058942.git.dawid.glazik@linux.intel.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
We currently have the apb's mapping of the i2c controller space as a
labelled mostly-empty node:
apb {
i2c: bus@1e78a000 {
ranges = <...>;
};
}
... and then define the contents of the i2c block later:
i2c: {
i2c0: i2c-bus@80 {
reg = <0x80 0x80>;
};
i2c1: i2c-bus@100 {
reg = <0x100 0x80>;
};
}
Krzysztof mentions[1] that isn't convention though, with the top-level
simple-bus being empty and linked via the label. So, drop the label
usage and move the i2c bus definition into the simple-bus node directly
under the apb:
apb {
bus@1e78a000 {
ranges = <...>;
i2c0: i2c-bus@80 {
reg = <0x80 0x80>;
};
i2c1: i2c-bus@100 {
reg = <0x100 0x80>;
};
};
}
This will allow us to be consistent when we add new definitions for the
i3c nodes, which would require the latter format.
Link: https://lore.kernel.org/linux-devicetree/c5331cf8-7295-4e6a-ba39-e0751a2c357e@kernel.org/ [1]
Suggested-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Dawid Glazik <dawid.glazik@linux.intel.com>
Link: https://patch.msgid.link/7c7010a87bb70b9e2abdadfea76d41cdcb88a82f.1777058942.git.dawid.glazik@linux.intel.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add sdp_type in AS SDP unpack. Since the field sdp_type is not compared
in intel_compare_dp_as_sdp() it doesn't throw up any mismatch error yet.
In the subsequent change this field will be added along with other missing
fields for comparison.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260511123218.1589830-4-ankit.k.nautiyal@intel.com
Correct the bit-shift logic to properly readback the 10 bit target_rr from
DB3 and DB4.
v2: Align the style with readback for vtotal. (Ville)
Fixes: 12ea892916 ("drm/i915/dp: Add Read/Write support for Adaptive Sync SDP")
Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260511123218.1589830-2-ankit.k.nautiyal@intel.com
Add tests to verify that bpf_throw() correctly unwinds the stack
when the program uses outgoing stack arguments (functions with >5
args). Without the preceding x86 fix, these tests crash the kernel
on x86 due to corrupted callee-saved register restore. There is
no change for arm64 to support exception with stack arguments.
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20260517150707.289273-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When a main program with exception_boundary has outgoing stack
arguments (e.g. from calling subprogs with >5 args), bpf_throw() fails
to correctly restore callee-saved registers, causing a kernel crash.
The x86 JIT allocates the outgoing stack arg area below the
callee-saved registers via 'sub rsp, outgoing_rsp' in the prologue.
When bpf_throw() unwinds, it captures the main program's sp (which
includes this outgoing area) and passes it to the exception callback.
The callback gets rsp and rbp, followed by pop_callee_regs, but rsp
points into the outgoing arg area rather than the callee-saved
registers, so the pops restore garbage values. Returning to the
kernel with corrupted callee-saved registers causes a crash.
Fix this by adjusting the sp (adding stack_arg_sp_adjust) passed to
the exception callback, so it points to the bottom of the callee-saved
registers instead of the outgoing arg area. When stack_arg_sp_adjust
is 0 (the common case), this is a no-op.
Fixes: 324c3ca6ee ("bpf,x86: Implement JIT support for stack arguments")
Acked-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20260517150702.288031-1-yonghong.song@linux.dev
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull to receive:
39e25a2100 ("sched_ext: Drop NONE early return in scx_disable_and_exit_task()")
b273b75b8d ("sched_ext: INIT_LIST_HEAD() &sch->all in scx_alloc_and_add_sched()")
cceb874eee ("sched_ext: Defer sub_kset base put to scx_sched_free_rcu_work")
6ae315d379 ("sched_ext: Use HK_TYPE_DOMAIN_BOOT to detect isolcpus= domain isolation")
515e3996a4 ("sched_ext: Fix deadlock between scx_root_disable() and concurrent forks")
to prepare for-7.2 for further sub-sched changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
At transition to the iov_iter for PCM data transfer, we blindly
applied the iov_iter setup also for silencing (i.e. data = NULL), and
it leads to a calculation of bogus iov_iter. Fortunately this didn't
cause troubles on most of architectures but it goes wrong on RISC-V
now, causing a NULL dereference.
Handle the NULL data case to treat the silencing in interleaved_copy()
for addressing the bug above. noninterleaved_copy() has already the
NULL data handling, so it doesn't need changes.
Reported-by: Jiakai Xu <xujiakai24@mails.ucas.ac.cn>
Closes: https://lore.kernel.org/20260515051516.3103036-1-xujiakai24@mails.ucas.ac.cn
Fixes: cf393babb3 ("ALSA: pcm: Add copy ops with iov_iter")
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260517165121.31399-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion Plus 14-eh0xxx with subsystem ID 103c:8a36 needs the
ALC245 COEF bit mute LED quirk for the mute LED to follow the audio mute
state.
Add the missing quirk entry.
Signed-off-by: Aryan Kushwaha <aryankushwaha3101@gmail.com>
Link: https://patch.msgid.link/20260516144436.35022-1-aryankushwaha3101@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
scx_root_disable() enters SCX_DISABLING before it grabs scx_enable_mutex to
clear __scx_switched_all and scx_switching_all. task_should_scx() short-circuits on DISABLING,
so forks in that window land on fair while next_active_class() still skips
fair - the new tasks stall.
This can deadlock the disable path itself: scx_alloc_and_add_sched() runs
under scx_enable_mutex and creates a helper kthread; if that new kthread is
one of the stalled fair tasks, the mutex holder waits forever and
scx_root_disable() can never make progress. Only sub-sched support exposes
this, since sub-sched enables are the only path where
scx_alloc_and_add_sched() can race the root's disable.
Move the DISABLING check after @scx_switching_all. @scx_switching_all
serves as a proxy for __scx_switched_all, so while it's set, forks keep
going to scx. Once cleared, DISABLING applies normally.
v2: Reword in-source comment and description. (Andrea)
Fixes: 337ec00b1d ("sched_ext: Implement cgroup sub-sched enabling and disabling")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
- Add more functions to the remote allowed list
randconfig found more functions that are allowed for the remote code for
s390 and arm. Add them to the allowed list.
- Fix remote_test error path
If one of the simple ring buffers fails to load, the code is supposed to
rollback its initialized buffers. Instead of rolling back the buffers for
the failed load, it uses the global variable and rolls back all the
successfully loaded buffers.
-----BEGIN PGP SIGNATURE-----
iIoEABYKADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCagm9FRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qn0xAP0WSYmbUAGYnrq1o5L4EEM61ManFBfp
ta7dmx1Q5SYw6AEAtqbiH42VJZviAmajguyuL0cs9i9exFl+j4SaneejNwg=
=CLqK
-----END PGP SIGNATURE-----
Merge tag 'trace-v7.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Add more functions to the remote allowed list
randconfig found more functions that are allowed for the remote code
for s390 and arm. Add them to the allowed list.
- Fix remote_test error path
If one of the simple ring buffers fails to load, the code is supposed
to rollback its initialized buffers. Instead of rolling back the
buffers for the failed load, it uses the global variable and rolls
back all the successfully loaded buffers.
* tag 'trace-v7.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix desc in error path for the trace remote test module
ring-buffer remote: Avoid unexpected symbol warnings (arm, s390)
When issuing an extended guest request (SVM_VMGEXIT_EXT_GUEST_REQUEST),
get_ext_report() allocates a buffer to retrieve a certificate blob from the
host, keeping track of its size in report_req->certs_len.
However, the host may return SNP_GUEST_VMM_ERR_INVALID_LEN, indicating
an invalid buffer size, as well as the expected length of such buffer.
get_ext_report() subsequently updates report_req->certs_len with the
host-controlled value, and cleans up the buffer by computing a page order
from such value. This is incorrect, as the host-provided length may not
match the page order of the original allocation, potentially resulting
in corruption in the page allocator.
Fix this by using alloc_pages_exact() instead, and reusing @npages to
compute the size passed to free_pages_exact(). For consistency, also
use @npages to compute the size when allocating the pages, even though
this last change has no functional effect.
Fixes: 3e385c0d6c ("virt: sev-guest: Move SNP Guest Request data pages handling under snp_cmd_mutex")
Signed-off-by: Carlos López <clopez@suse.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Michael Roth <michael.roth@amd.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kumar Kartikeya Dwivedi says:
====================
Fix bpf_throw() vs global subprogs interaction
There is a bug where bpf_throw()'s reachability across global subprogs
is missed by the verifier, leading to successful verification when any
kernel resource or lock is held across global subprog call boundary.
Fix this by effect summarization like other related side effects and
propagate exception reachability into callees.
Changelog:
----------
v1 -> v2
v1: https://lore.kernel.org/bpf/20260516022426.2109698-1-memxor@gmail.com
* Reorder might_throw bit to avoid bpf-next conflicts. (Alexei)
====================
Link: https://patch.msgid.link/20260517075530.3461166-1-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a verifier failure case where the caller holds a reference across a
global subprog call that may throw. The program must be rejected because
the exceptional path would skip the caller's reference release.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20260517075530.3461166-3-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Global subprogs are verified independently and are not descended into
when their callers are symbolically executed. This means a caller can
hold references or locks across a global subprog call that may throw,
while the verifier only checks the non-exceptional return path at the
call site.
Record whether a subprog might throw in the CFG summary pass, alongside
the existing might_sleep and packet-data-changing summaries, and
propagate that effect through reachable callees.
When a global subprog is marked as possibly throwing, push the normal
continuation and validate the exceptional path immediately at the call
site, avoiding a synthetic exception state and associated special case
in the pruning checks.
Fixes: f18b03faba ("bpf: Implement BPF exceptions")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20260517075530.3461166-2-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- Fix use-after-free in irq_work_single() on PREEMPT_RT
(Jiayuan Chen)
- Don't call add_interrupt_randomness() for NMIs
in handle_percpu_devid_irq() (Mark Rutland)
- Remove unused function in the ath79-cpu irqchip driver
causing LKP CI build warnings (Rosen Penev)
- Fix IRQ allocation/teardown leakage regressions in the GICv5
irqchip driver (Sascha Bischoff)
- Fix an IRQ trigger type regression in the Meson S4 SoC irqchip
driver (Xianwei Zhao)
- Fix CPU offlining regression in the RiscV IMSIC irqchip driver
(Yong-Xuan Wang)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=rLcN
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2026-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull IRQ fixes from Ingo Molnar:
- Fix use-after-free in irq_work_single() on PREEMPT_RT (Jiayuan Chen)
- Don't call add_interrupt_randomness() for NMIs in
handle_percpu_devid_irq() (Mark Rutland)
- Remove unused function in the ath79-cpu irqchip driver causing LKP
CI build warnings (Rosen Penev)
- Fix IRQ allocation/teardown leakage regressions in the GICv5 irqchip
driver (Sascha Bischoff)
- Fix an IRQ trigger type regression in the Meson S4 SoC irqchip driver
(Xianwei Zhao)
- Fix CPU offlining regression in the RiscV IMSIC irqchip driver
(Yong-Xuan Wang)
* tag 'irq-urgent-2026-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT
irqchip/riscv-imsic: Clear interrupt move state during CPU offlining
irqchip/meson-gpio: Use the correct register in meson_s4_gpio_irq_set_type()
irqchip/ath79-cpu: Remove unused function
genirq/chip: Don't call add_interrupt_randomness() for NMIs
irqchip/gic-v5: Allocate ITS parent LPIs as a range
irqchip/gic-v5: Support range allocation for LPIs
irqchip/gic-v5: Move LPI allocation into the LPI domain
Add Vol+/Vol-/Mute panel button mappings for iMON VFD HID OEM v1.2.
This version differs in the codes that generate the
KEY_VOLUMEUP, KEY_VOLUMEDOWN and KEY_MUTE events.
Signed-off-by: Alessandro Baldi <baldovic@virgilio.it>
Signed-off-by: Sean Young <sean@mess.org>
- Disable satp register probing when no5lvl is specified on the kernel
command line
- Fix a CFI-related issue with the misaligned access speed measurement
code
- Reduce the CFI shadow stack size limit from 4GB to 2GB (following
ARM64 GCS)
- Prevent the kernel from requesting delegation of misaligned access
faults unless a new Kconfig option,
CONFIG_RISCV_SBI_FWFT_DELEGATE_MISALIGNED, is enabled. This will
depend on CONFIG_NONPORTABLE until the deficiencies of the kernel
misaligned access fixup code are fixed
- Fix some potential uninitialized memory accesses in error paths in
compat_riscv_gpr_set() and compat_restore_sigcontext()
- Fix a bug in the RISC-V MIPS vendor errata patching code where a
logical-and was used in place of a bitwise-and
- Drop some unnecessary code in riscv_fill_hwcap_from_isa_string()
- Use macros for isa2hwcap indices in riscv_fill_hwcap(), rather than
open-coding them
- Fix some documentation typos (one affecting "make htmldocs")
-----BEGIN PGP SIGNATURE-----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=yOtI
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-7.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Relatively low-impact fixes. Probably the most notable one is that we
no longer ask the monitor-mode firmware to delegate misaligned access
handling to the kernel by default, since the kernel code needs
significant improvement to match the functionality of the firmware.
This change avoids functional problems at some cost in performance,
but shouldn't affect any system with misaligned access handling in
hardware.
- Disable satp register probing when no5lvl is specified on the
kernel command line
- Fix a CFI-related issue with the misaligned access speed
measurement code
- Reduce the CFI shadow stack size limit from 4GB to 2GB (following
ARM64 GCS)
- Prevent the kernel from requesting delegation of misaligned access
faults unless a new Kconfig option, RISCV_SBI_FWFT_DELEGATE_MISALIGNED,
is enabled. This will depend on CONFIG_NONPORTABLE until the
deficiencies of the kernel misaligned access fixup code are fixed
- Fix some potential uninitialized memory accesses in error paths in
compat_riscv_gpr_set() and compat_restore_sigcontext()
- Fix a bug in the RISC-V MIPS vendor errata patching code where a
logical-and was used in place of a bitwise-and
- Drop some unnecessary code in riscv_fill_hwcap_from_isa_string()
- Use macros for isa2hwcap indices in riscv_fill_hwcap(), rather than
open-coding them
- Fix some documentation typos (one affecting 'make htmldocs')"
* tag 'riscv-for-linus-7.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: misaligned: Make enabling delegation depend on NONPORTABLE
riscv: Docs: fix unmatched quote warning
riscv: cfi: reduce shadow stack size limit from 4GB to 2GB
riscv: cpufeature: Use pre-defined ISA ext macros to index isa2hwcap
riscv: mm: Fixup no5lvl failure when vaddr is invalid
riscv: Fix register corruption from uninitialized cregs on error
riscv: errata: Fix bitwise vs logical AND in MIPS errata patching
Documentation: riscv: cmodx: fix typos
riscv: cpufeature: Drop this_hwcap clear in T-Head vector workaround
riscv: Define __riscv_copy_{,vec_}{words,bytes}_unaligned() using SYM_TYPED_FUNC_START
The BPT stream was allocated in intel_ace2x_bpt_open_stream(), we need
to free it in intel_ace2x_bpt_close_stream().
Fixes: 4c1ce9f37d ("soundwire: intel_ace2x: add BPT send_async/wait callbacks")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Simon Trimmer <simont@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.dev>
Link: https://patch.msgid.link/20260514141625.1834216-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the typo "clocks-names" to "clock-names" in the allOf/if conditional
blocks.
Fixes: 9be5c47908 ("dt-bindings: display/msm: expand to support MST")
Fixes: 7403e87c13 ("dt-bindings: display: msm: Fix reg ranges and clocks on Glymur")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/721682/
Message-ID: <20260428100338.3179722-1-prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
When protected KVM is enabled, the kernel includes a pKVM FF-A proxy
that sits in front of the normal FF-A driver. The proxy has to perform
its own FF-A version negotiation and setup first, so that it can mediate
subsequent FF-A traffic correctly.
Defer FF-A core probing until pKVM has completed initialization. This
keeps the normal driver from negotiating the FF-A version or performing
other transport setup before the pKVM proxy is ready, and lets the
driver model retry probing once the protected KVM state required by the
FF-A transport is available.
Suggested-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Link: https://patch.msgid.link/20260508-b4-ffa_plat_dev-v1-4-c5a30f8cf7b8@kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@kernel.org>
Pass a parent device into ffa_device_register() and use the synthetic
arm-ffa platform device as the parent for each registered FF-A device.
This keeps the enumerated FF-A partition devices anchored below the FF-A
core device in the driver model, matching the platform-driver conversion
of the core transport.
Suggested-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Link: https://patch.msgid.link/20260508-b4-ffa_plat_dev-v1-3-c5a30f8cf7b8@kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@kernel.org>
Move the FF-A core bring-up and teardown paths into platform driver
probe and remove callbacks, and register a synthetic arm-ffa platform
device to bind the driver.
This makes the FF-A core lifetime follow the driver model while keeping
the device creation internal to the FF-A core. Use normal platform driver
registration so the probe path has standard driver-core semantics.
The synthetic platform device is a temporary bridge until ACPI and
devicetree describe the FF-A core device or object. Once those firmware
description paths are defined, the internal platform device creation can
be dropped and the driver can bind to the firmware-described device
directly.
Since the transport selection now happens from the platform probe path,
drop the __init annotation from ffa_transport_init().
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Link: https://patch.msgid.link/20260508-b4-ffa_plat_dev-v1-2-c5a30f8cf7b8@kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@kernel.org>
This reverts commit 0e0546eabc, which was
added to address ordering issues with the IMA LSM initialisation where
the TPM would not be fully ready by the time IMA wanted it. This has
been resolved within IMA by retrying setup during late_initcall_sync if
the TPM is not available at first.
Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com>
Link: https://patch.msgid.link/20260508-b4-ffa_plat_dev-v1-1-c5a30f8cf7b8@kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@kernel.org>
Enable the QSPI controller and the XM25QU128C SPI NOR flash on the
OrangePi RV2 board. Add a flash partition layout from vendor UBoot.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Link: https://patch.msgid.link/20260516080030.1736836-1-amadeus@jmu.edu.cn
Signed-off-by: Yixun Lan <dlan@kernel.org>
The PANEL_BOOT_MESSAGE dependency uses a quoted-string comparison
against the PANEL_CHANGE_MESSAGE bool symbol:
depends on PANEL_CHANGE_MESSAGE="y"
This is the only such pattern under drivers/auxdisplay/ (grep shows
no other Kconfig file in the tree uses depends on FOO="y" with
quotes for a plain bool symbol). The quoted form is parsed by
Kconfig but is not idiomatic; the common form for the same intent
is the unquoted tristate-style dependency:
depends on PANEL_CHANGE_MESSAGE
which evaluates true when PANEL_CHANGE_MESSAGE is y or m. Since
PANEL_CHANGE_MESSAGE is declared as bool (not tristate), there is
no behaviour change in practice: y is the only enabled value
either form can match.
Drop the quoted comparison so the dependency matches the prevailing
kernel Kconfig style and so it is obvious to readers that the
comparison works.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/CAHp75VfsA_LsbEKjxoeMdbhPbWj7OHZ7=0SYNA3c=ZLj_M94Bw@mail.gmail.com
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
linedisp_display() unconditionally reads msg[count - 1] before
checking whether count is zero, so a write of zero bytes to the
message sysfs attribute hits msg[-1]:
write(fd, "", 0);
-> message_store(..., buf, count=0)
-> linedisp_display(linedisp, buf, count=0)
-> msg[count - 1] == '\n' ; OOB read
The kernfs write buffer for that store is a 1-byte allocation
(kernfs_fop_write_iter() does kmalloc(len + 1) with len == 0),
so msg[-1] is a 1-byte read before the slab object. On a
KASAN-enabled kernel this trips an out-of-bounds report and
panics; on stock kernels it silently reads adjacent slab data
and, if that byte happens to be '\n', the following count--
wraps ssize_t 0 to -1 and is then passed to kmemdup_nul().
linedisp_display() is reached from the message_store() sysfs
callback (drivers/auxdisplay/line-display.c message attribute,
mode 0644) and from the in-tree initial-message setup with
count == -1, so the OOB path is only userspace-triggerable via
zero-byte writes; vfs_write() does not short-circuit on
count == 0 and kernfs_fop_write_iter() dispatches the store
callback regardless.
Guard the trailing-newline trim with a count check. The
existing if (!count) block then takes the clear-display path
unchanged.
Affects every auxdisplay driver that registers via
linedisp_register() / linedisp_attach(): ht16k33, max6959,
img-ascii-lcd, seg-led-gpio.
Fixes: 7e76aece6f ("auxdisplay: Extract character line display core support")
Signed-off-by: Stepan Ionichev <sozdayvek@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
