Use the AMD errata checking framework instead of open-coding the test.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
LKML-Reference: <1280336972-865982-3-git-send-email-hans.rosenfeld@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Remove check_c1e_idle() and use the new AMD errata checking framework
instead.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
LKML-Reference: <1280336972-865982-2-git-send-email-hans.rosenfeld@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Errata are defined using the AMD_LEGACY_ERRATUM() or AMD_OSVW_ERRATUM()
macros. The latter is intended for newer errata that have an OSVW id
assigned, which it takes as first argument. Both take a variable number
of family-specific model-stepping ranges created by AMD_MODEL_RANGE().
Iff an erratum has an OSVW id, OSVW is available on the CPU, and the
OSVW id is known to the hardware, it is used to determine whether an
erratum is present. Otherwise, the model-stepping ranges are matched
against the current CPU to find out whether the erratum applies.
For certain special errata, the code using this framework might have to
conduct further checks to make sure an erratum is really (not) present.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
LKML-Reference: <1280336972-865982-1-git-send-email-hans.rosenfeld@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Conflicts:
arch/powerpc/kernel/time.c
Reason: The powerpc next tree contains two commits which conflict with
the timekeeping changes:
8fd63a9e powerpc: Rework VDSO gettimeofday to prevent time going backwards
c1aa687d powerpc: Clean up obsolete code relating to decrementer and timebase
John Stultz identified them and provided the conflict resolution.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the decrementer and timekeeping code was moved over to using
the generic clockevents and timekeeping infrastructure, several
variables and functions have been obsolete and effectively unused.
This deletes them.
In particular, wakeup_decrementer() is no longer needed since the
generic code reprograms the decrementer as part of the process of
resuming the timekeeping code, which happens during sysdev resume.
Thus the wakeup_decrementer calls in the suspend_enter methods for
52xx platforms have been removed. The call in the powermac cpu
frequency change code has been replaced by set_dec(1), which will
cause a timer interrupt as soon as interrupts are enabled, and the
generic code will then reprogram the decrementer with the correct
value.
This also simplifies the generic_suspend_en/disable_irqs functions
and makes them static since they are not referenced outside time.c.
The preempt_enable/disable calls are removed because the generic
code has disabled all but the boot cpu at the point where these
functions are called, so we can't be moved to another cpu.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently it is possible for userspace to see the result of
gettimeofday() going backwards by 1 microsecond, assuming that
userspace is using the gettimeofday() in the VDSO. The VDSO
gettimeofday() algorithm computes the time in "xsecs", which are
units of 2^-20 seconds, or approximately 0.954 microseconds,
using the algorithm
now = (timebase - tb_orig_stamp) * tb_to_xs + stamp_xsec
and then converts the time in xsecs to seconds and microseconds.
The kernel updates the tb_orig_stamp and stamp_xsec values every
tick in update_vsyscall(). If the length of the tick is not an
integer number of xsecs, then some precision is lost in converting
the current time to xsecs. For example, with CONFIG_HZ=1000, the
tick is 1ms long, which is 1048.576 xsecs. That means that
stamp_xsec will advance by either 1048 or 1049 on each tick.
With the right conditions, it is possible for userspace to get
(timebase - tb_orig_stamp) * tb_to_xs being 1049 if the kernel is
slightly late in updating the vdso_datapage, and then for stamp_xsec
to advance by 1048 when the kernel does update it, and for userspace
to then see (timebase - tb_orig_stamp) * tb_to_xs being zero due to
integer truncation. The result is that time appears to go backwards
by 1 microsecond.
To fix this we change the VDSO gettimeofday to use a new field in the
VDSO datapage which stores the nanoseconds part of the time as a
fractional number of seconds in a 0.32 binary fraction format.
(Or put another way, as a 32-bit number in units of 0.23283 ns.)
This is convenient because we can use the mulhwu instruction to
convert it to either microseconds or nanoseconds.
Since it turns out that computing the time of day using this new field
is simpler than either using stamp_xsec (as gettimeofday does) or
stamp_xtime.tv_nsec (as clock_gettime does), this converts both
gettimeofday and clock_gettime to use the new field. The existing
__do_get_tspec function is converted to use the new field and take
a parameter in r7 that indicates the desired resolution, 1,000,000
for microseconds or 1,000,000,000 for nanoseconds. The __do_get_xsec
function is then unused and is deleted.
The new algorithm is
now = ((timebase - tb_orig_stamp) << 12) * tb_to_xs
+ (stamp_xtime_seconds << 32) + stamp_sec_fraction
with 'now' in units of 2^-32 seconds. That is then converted to
seconds and either microseconds or nanoseconds with
seconds = now >> 32
partseconds = ((now & 0xffffffff) * resolution) >> 32
The 32-bit VDSO code also makes a further simplification: it ignores
the bottom 32 bits of the tb_to_xs value, which is a 0.64 format binary
fraction. Doing so gets rid of 4 multiply instructions. Assuming
a timebase frequency of 1GHz or less and an update interval of no
more than 10ms, the upper 32 bits of tb_to_xs will be at least
4503599, so the error from ignoring the low 32 bits will be at most
2.2ns, which is more than an order of magnitude less than the time
taken to do gettimeofday or clock_gettime on our fastest processors,
so there is no possibility of seeing inconsistent values due to this.
This also moves update_gtod() down next to its only caller, and makes
update_vsyscall use the time passed in via the wall_time argument rather
than accessing xtime directly. At present, wall_time always points to
xtime, but that could change in future.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we don't need a huge amount of memory in ->readdir() then
we can use kmalloc rather than vmalloc to allocate it. This
should cut down on the greater overheads associated with
vmalloc for smaller directories.
We may be able to eliminate vmalloc entirely at some stage,
but this is easy to do right away.
Also using GFP_NOFS to avoid any issues wrt to deleting inodes
while under a glock, and suggestion from Linus to factor out
the alloc/dealloc.
I've given this a test with a variety of different sized
directories and it seems to work ok.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Long ago, when bridge was converted to RCU, rcu lock was equivalent
to having preempt disabled. RCU has changed a lot since then and
bridge code was still assuming the since transmit was called with
bottom half disabled, it was RCU safe.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts pci_table entries, where .subvendor=PCI_ANY_ID and
.subdevice=PCI_ANY_ID, .class=0 and .class_mask=0, to use the
PCI_VDEVICE macro, and thus improves readability.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable PC-beep as default for hardwares that aren't compliant with the
SSID value Realtek requires. In such a case, better to enable the beep
to avoid a regression.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We check now the availability of PC beep and skip the build of beep
mixers, but the driver still registers the input device. This should
be checked as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove find_gcf from nldr.c and use kernel function
gcd().
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove bridge_brd_delete() function since it is
doing the same that bridge_brd_stop().
Signed-off-by: Ernesto Ramos <ernesto@ernesto-desktop.(none)>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Regardless the IVA2 power state before bridgedriver is
installed, the driver must ensure that IVA2 power
state is OFF when the device driver is created.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a base image is being loaded or started and by some reason
the process fails, the IVA2 should be switched OFF.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
right now, bridge_brd_stop is not changing the IVA2 power state
to OFF since PM_PWSTST_IVA2 is not 0 after calling this function.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_FAILED
is not necessary anymore. This patch removes this
define.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is 0, DSP_FAILED macro
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore. This patch removes this
define.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since status succeeded is now 0 macro DSP_SUCCEEDED
is not necessary anymore.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove function delete_strm_mgr in strm.c and
use kfree instead.
Signed-off-by: Ernesto Ramos <ernesto@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
update TODO to reflect the items taken care of,
update ABI to reflect the new debugfs entries exposed.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the chip is in use, information like the chip's ROM version and the
protocols currently making use of the chip needs to be made known to
user-space.
Earlier the version and the protocol-list were exposed as sysfs entries
now cleanup by making them as debugfs entries, also in process remove
any unwanted/previously unused sysfs entries.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Exploit the cio siosl function to trigger logging in the FCP channel
on qdio error conditions. Add a helper function in zfcp_qdio to ensure
that tracing is only triggered once before calling qdio_shutdown.
Trigger in zfcp for hardware logs are:
- timeout for FSF requests to the FCP channel
- "no recommendation" status from FCP channel
- invalid FSF protocol status
- stalled outbound queue
- unknown request id on inbound queue
- QDIO_ERROR_SLSB_STATE
All of the above triggers run from the Linux qdio softirq context, so
no additional synchronization is necessary for the handling of the
ZFCP_STATUS_ADAPTER_SIOSL_ISSUED flag.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Introduce support for DIF/DIX in zfcp: Report the capabilities for the
Scsi_host, map the protection data when issuing I/O requests and
handle the new error codes. Also add the fsf data_direction field to
the hba trace, it is useful information for debugging in that area.
This is an EXPERIMENTAL feature for now.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Try to enable data division support for FCP devices and indicate in
the adapter status flag if it succeeded.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Initialize allocated memory to zero to prevent access on error. This
prevents a possible error in the error handling path.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Post FC transport class netlink events for usage in the userspace,
e.g. for HBAAPI. Supported events are those required for the
polled events in HBAAPI.
- link up
- link down
- incoming RSCN
(events related to FC-AL are not supported, as zfcp has no support for FC-AL)
Signed-off-by: Sven Schuetz <sven@linux.vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some definitions and structures in the zfcp QDIO processing are
improved by the removal of not required variables and processing steps.
I addition the naming of some variables is changed to make their purpose
more clear.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A lot of functions require the amount of SBALs as one of their
parameter which is most times invariable. Therefore remove this
parameter and set the SBAL value explicitly if a non standard value is
required. In addition the warning message "oversized data" is
replaced with a BUG_ON() statement assuring the limits defined and
requested by zfcp.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The timer_interval is 14 bits in width. Introduce a define for
properly masking the value.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Configuring a LUN in zfcp, also creates a SCSI device. For
consistency, it makes sense to remove the SCSI device when the LUN is
deconfigured. Replace the flush_work with the call to
scsi_remove_device: scsi_remove_device also takes the scan_mutex that
synchronizes itself with any long running device discovery.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use the functions memdup_user and kstrdup to allocate memory and copy
the data in one step, saving some lines of code.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Trying to enqueue a port erp action from the port erp strategy will
fail in zfcp_erp_required_act. To try the same action again, return
ZFCP_ERP_FAILED.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After a timeout notification, do not try to run the erp strategy.
Return from the erp with "failed" to possibly trigger a retry.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When running in non-NPIV mode, the port_reopen in terminate_rport_io
might succeed even though the remote port is not available. If the
same port connection is held open from another operating system, the
reopen is only a virtual operation and might not hit the SAN. Fix this
by changing the call to forced_reopen that forces a logout/login
operation in the SAN.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>