For real HiperSockets the EBCDIC-ASCII conversion is not necessary.
This is only needed for z/VM GuestLAN devices.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modify carrier state determination for 802.3ad mode to comply
with section 43.3.9 of IEEE 802.3, which requires that "Links that are
not successful candidates for aggregation (e.g., links that are attached
to other devices that cannot perform aggregation or links that have been
manually configured to be non-aggregatable) are enabled to operate as
individual IEEE 802.3 links."
Bug reported by Laurent Chavey <chavey@google.com>. This patch
is an updated version of his patch that changes the wording of
commentary and adds an update to the driver version.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Laurent Chavey <chavey@google.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch (based on a patch from Stephen Hemminger
<shemminger@linux-foundation.org>) removes use after free conditions in
the unregister path for the bonding master. Without this patch, an
operation of the form "echo -bond0 > /sys/class/net/bonding_masters"
would trigger a NULL pointer dereference in sysfs. I was not able to
induce the failure with the non-sysfs code path, but for consistency I
updated that code as well.
I also did some testing of the bonding /proc file being open
while the bond is being deleted, and didn't see any problems there.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It doesn't look like spidernet hardware can really checksum all protocols,
the code looks like it does IPV4 only. If so, it should use NETIF_F_IP_CSUM
instead of NETIF_F_HW_CSUM.
The driver doesn't need it's own get/set for ethtool tx csum, and it
should use the standard ethtool_op_get_link.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At some point, the transmit descriptor chain end interrupt (TXDCEINT)
was turned on. This is a mistake; and it damages small packet
transmit performance, as it results in a huge storm of interrupts.
Turn it off.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Although the previous patch resolved issues with hangs when the
RX ram full interrupt is encountered, there are still situations
where lots of RX ramfull interrupts arrive, resulting in a noisy
log in syslog. There is no need for this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The terminated RX ring will cause trouble during the RX ram full
conditions, leading to a hung driver, as the hardware can't find
the next descr. There is no real reason to terminate the RX ring;
it doesn't make the operation any smooother, and it does
require an extra sync. So don't do it.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a rare deadlock that can occur when the kernel
is not able to empty out the RX ring quickly enough. Below follows
a detailed description of the bug and the fix.
As long as the OS can empty out the RX buffers at a rate faster than
the hardware can fill them, there is no problem. If, for some reason,
the OS fails to empty the RX ring fast enough, the hardware GDACTDPA
pointer will catch up to the head, notice the not-empty condition,
ad stop. However, RX packets may still continue arriving on the wire.
The spidernet chip can save some limited number of these in local RAM.
When this local ram fills up, the spider chip will issue an interrupt
indicating this (GHIINT0STS will show ERRINT, and the GRMFLLINT bit
will be set in GHIINT1STS). When te RX ram full condition occurs,
a certain bug/feature is triggered that has to be specially handled.
This section describes the special handling for this condition.
When the OS finally has a chance to run, it will empty out the RX ring.
In particular, it will clear the descriptor on which the hardware had
stopped. However, once the hardware has decided that a certain
descriptor is invalid, it will not restart at that descriptor; instead
it will restart at the next descr. This potentially will lead to a
deadlock condition, as the tail pointer will be pointing at this descr,
which, from the OS point of view, is empty; the OS will be waiting for
this descr to be filled. However, the hardware has skipped this descr,
and is filling the next descrs. Since the OS doesn't see this, there
is a potential deadlock, with the OS waiting for one descr to fill,
while the hardware is waiting for a differen set of descrs to become
empty.
A call to show_rx_chain() at this point indicates the nature of the
problem. A typical print when the network is hung shows the following:
net eth1: Spider RX RAM full, incoming packets might be discarded!
net eth1: Total number of descrs=256
net eth1: Chain tail located at descr=255
net eth1: Chain head is at 255
net eth1: HW curr desc (GDACTDPA) is at 0
net eth1: Have 1 descrs with stat=xa0800000
net eth1: HW next desc (GDACNEXTDA) is at 1
net eth1: Have 127 descrs with stat=x40800101
net eth1: Have 1 descrs with stat=x40800001
net eth1: Have 126 descrs with stat=x40800101
net eth1: Last 1 descrs with stat=xa0800000
Both the tail and head pointers are pointing at descr 255, which is
marked xa... which is "empty". Thus, from the OS point of view, there
is nothing to be done. In particular, there is the implicit assumption
that everything in front of the "empty" descr must surely also be empty,
as explained in the last section. The OS is waiting for descr 255 to
become non-empty, which, in this case, will never happen.
The HW pointer is at descr 0. This descr is marked 0x4.. or "full".
Since its already full, the hardware can do nothing more, and thus has
halted processing. Notice that descrs 0 through 254 are all marked
"full", while descr 254 and 255 are empty. (The "Last 1 descrs" is
descr 254, since tail was at 255.) Thus, the system is deadlocked,
and there can be no forward progress; the OS thinks there's nothing
to do, and the hardware has nowhere to put incoming data.
This bug/feature is worked around with the spider_net_resync_head_ptr()
routine. When the driver receives RX interrupts, but an examination
of the RX chain seems to show it is empty, then it is probable that
the hardware has skipped a descr or two (sometimes dozens under heavy
network conditions). The spider_net_resync_head_ptr() subroutine will
search the ring for the next full descr, and the driver will resume
operations there. Since this will leave "holes" in the ring, there
is also a spider_net_resync_tail_ptr() that will skip over such holes.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Avoid kernel crash in mm/slab.c due to double-free of pointer.
If the ethernet interface is brought down while there is still
RX traffic in flight, the device shutdown routine can end up
trying to double-free an skb, leading to a crash in mm/slab.c
Avoid the double-free by nulling out the skb pointer.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Only set client->iso_context if allocation was successful.
ieee1394: fix to ether1394_tx in ether1394.c
firewire: fix hang after card ejection
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure inline data segments don't cross a 64 byte boundary
IB/mlx4: Handle FW command interface rev 3
IB/mlx4: Handle buffer wraparound in __mlx4_ib_cq_clean()
IB/mlx4: Get rid of max_inline_data calculation
IB/mlx4: Handle new FW requirement for send request prefetching
IB/mlx4: Fix warning in rounding up queue sizes
IB/mlx4: Fix handling of wq->tail for send completions
This patch fixes an OOPS on cdev release for an fd where iso context
creation failed.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
It's already annoying that they appear on x86 now -- that's for the 3button
emulation needed on x86 macs -- but at least don't make them default.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not directly related to x86, but I got tired of seeing these warnings on every
kconfig update when building on a non m68k box:
drivers/input/keyboard/Kconfig:170:warning: 'select' used by config symbol 'KEYBOARD_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
drivers/input/mouse/Kconfig:182:warning: 'select' used by config symbol 'MOUSE_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
I moved the definition of ATARI_KBD_CORE into drivers/input/keyboard/Kconfig
so it's always seen by Kconfig.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some platforms it's definitions may conflict. So that's the one-liner.
The rest is 10 square kilometers of collateral damage fixup this include
used to paper over.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support displaying long serial number information. Reuse sysfs handler
internally as helper.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Dell PERC2/QC erroneously was listed as having the 31 bit limit
quirk on the interface allocations, removing the reference to repair
this oversight. Also, the 2 quad pci address (family) match catch-all
also retained the 31 bit limit and the 34 SG limit quirks in a paranoid
move. Now, many years later, we find that none of the Adapters that did
trigger with the family match had such quirks; these quirks are all
limited to the 4 quad pci address matches to select legacy adapters
already populated.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
asus_acpi_init() has a hack to prevent the driver from loading
when asus_hotk_add() fails. However, it was returning the successful
return value of acpi_bug_registger_driver() on failure. This caused
an oops on unload. Instead it should return -ENODEV.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is more like a spelling correction than a fix. It was
discovered that if we had a busy status return from the Adapter for the
SCSI srb command to a physical component, that we returned
DID_NO_CONNECT rather than what one would expect DID_BUS_BUSY.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- a4000t.c: Add missing include, needed in some configurations
- bvme6000_scsi.c: Kill bogus opening brace
- zorro7xx.c: Remove MODULE_DEVICE_TABLE, it should be part of another
patch
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove redundant defines from the header, replace all occurances in the
code with standard SAM_STAT_ macros. Also fix what seems to be a typo in
testing for (status == H_OVER_UNDER_RUN)...
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When reporting SCSI devices to the SCSI midlayer, use the FCP LUN as
LUN reported to the SCSI layer. With this approach, zfcp does not have
to create unique LUNS, and this code can be removed.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In some cases we did not reset some adapter status flags properly.
This patch clears these flags during FCP adapter shutdown.
Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added members for volume number and real memory size to header information.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
iscsi_iser: convert to use the data buffer accessors
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
TODO: use scsi_for_each_sg().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Inline data segments in send WQEs are not allowed to cross a 64 byte
boundary. We use inline data segments to hold the UD headers for MLX
QPs (QP0 and QP1). A send with GRH on QP1 will have a UD header that
is too big to fit in a single inline data segment without crossing a
64 byte boundary, so split the header into two inline data segments.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When compacting CQ entries, we need to set the correct value of the
ownership bit in case the value is different between the index we copy
the CQE from and the index we copy it to.
Found by Ronni Zimmerman of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The calculation of max_inline_data in set_kernel_sq_size() is bogus,
since it doesn't take into account the fact that inline segments may
not cross a 64-byte boundary, and hence multiple inline segments will
probably need to be used to post large inline sends.
We don't support inline sends for kernel QPs anyway, so there's no
point in doing this calculation anyway, since the field is just zeroed
out a little later. So just delete the bogus calculation.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New ConnectX firmware introduces FW command interface revision 2,
which requires that for each QP, a chunk of send queue entries (the
"headroom") is kept marked as invalid, so that the HCA doesn't get
confused if it prefetches entries that haven't been posted yet. Add
code to the driver to do this, and also update the user ABI so that
userspace can request that the prefetcher be turned off for userspace
QPs (we just leave the prefetcher on for all kernel QPs).
Unfortunately, marking send queue entries this way is confuses older
firmware, so we change the driver to allow only FW command interface
revisions 2. This means that users will have to update their firmware
to work with the new driver, but the firmware is changing quickly and
the old firmware has lots of other bugs anyway, so this shouldn't be too
big a deal.
Based on a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the routine acpi_ut_create_package_object(), if the
ACPI_ALLOCATE_ZEROED() fails then ACPI_FREE(package_desc) is called as
part of the cleanup. This should instead be
acpi_ut_remove_reference(package_desc) in order to remove the reference
acquired from acpi_ut_create_internal_object() [see the routine
acpi_ut_create_buffer_object() as an example of proper functionality].
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
if acpi_bus_get_device() returns NULL, print nothing
instead of "<NUL" in /proc/acpi/thermal_zone/*/trip_points
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch updates the driver version to 8.2.1
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is a reworked version of the data buffer accessors patch
so that it applies on the NPIV sources.
The original patch was developed and submitted by Fujita Tomonori:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
http://marc.info/?l=linux-scsi&m=117896446832171&w=2
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Following the NPIV support, the following changes have been accumulated
in the testing and qualification of the driver:
- Fix affinity of ELS ring to slow/deferred event processing
- Fix Ring attention masks
- Defer dev_loss_tmo timeout handling to worker thread
- Consolidate link down error classification for better error checking
- Remove unused/deprecated nlp_initiator_tmr timer
- Fix for async scan - move adapter init code back into pci_probe_one
context. Fix async scan interfaces.
- Expand validation of ability to create vports
- Extract VPI resource cnt from firmware
- Tuning of Login/Reject policies to better deal with overwhelmned targets
- Misc ELS and discovery fixes
- Export the npiv_enable attribute to sysfs
- Mailbox handling fix
- Add debugfs support
- A few other small misc fixes:
- wrong return values, double-frees, bad locking
- Added adapter failure heartbeat
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is added to the driver. It utilizes the interfaces of
the fc transport for the creation and deletion of vports. Within the
driver, a new Scsi_Host is created for each NPIV instance, and is
paired with a new instance of a FC port. This allows N FC Port
elements to share a single Adapter.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NPIV support is only available via new adapter interface extensions,
termed SLI-3. This interface changes some of the basic behaviors such
as command and response ring element sizes and data structures, as
well as a change in buffer posting. Note: the new firmware extensions
are found only on our mid-range and enterprise 4Gig adapters - so NPIV
support is available only on these newer adapters. The latest firmware
can be downloaded from the Emulex support page.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is reorganized to separate the handling of the adapter from
the handling of the FC port. Adapter handling includes submissions of
command requests, receiving responses, and managing adapter resources.
The FC port includes the discovery engine, login handling, and the
mapping of a Scsi_Host on the "port". Although not a large functional
change, as it touches core structures and functions, resulting in a
large text delta.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for Amiga Zorro bus NCR53c710 SCSI controllers, using the 53c700
SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the Amiga 4000T built-in NCR53c710 SCSI controller, using the
53c700 SCSI core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the MVME16x NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New driver for the BVME6000 NCR53C710 SCSI controller, using the 53c700 SCSI
core.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add m68k support to the 53c700 SCSI driver
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If there is IO going to the volume while a hidden disk is being torn down,
there is a case where we would return a DID_NO_CONNECT for IO sent to the
volume. The end result is the volume goes read-only. This problem is due to the
fact the firmware mapped target ids saved in per device object is phys_disk_num
for hidden raid components, and target_id for the volume. There is a single
case when both phys_disk_num and target_id are equal, so enters this issue. We
fix this issue by checking the tflags when the device is torned down,
insuring the IO being completed is meant for hidden raid component, not the
volume. In addition to this fix, there are a couple other cases to address
hidden raid components. For instance task_abort and device reset are not
supported by mpt fw for hidden raid components, a bus reset would be required
or target reset to volume.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
nice cosmetic cleaning of eh thread callback funtions
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>