Commit graph

89,737 commits

Author SHA1 Message Date
Stephen Hemminger
50432cb534 sky2: memory barriers change
Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.

Signed-off-by: Stephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:43:14 -04:00
Stephen Hemminger
84787e3fc3 sky2: remove dual port workaround
This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:43:14 -04:00
Stephen Hemminger
a3caeada94 sky2: MIB counter overflow handling
Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:43:14 -04:00
Stephen Hemminger
3225b91903 sky2: keep track of receive alloc failures
When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:43:13 -04:00
Stephen Hemminger
53419c6851 sky2: PHY register settings
Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:43:13 -04:00
Stephen Hemminger
abc368a17c sky2: remove Gigabyte 88e8056 restriction
The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:43:13 -04:00
David Woodhouse
b5b82df6f4 NS16550A: Restore HS settings in EXCR2 on resume
After a suspend/resume cycle, the UART may have been reset into
low-speed mode -- either because it's actually been reset, or because
the firmware pokes at the old-style divisor registers. If we detected it
as a NS16550A SuperIO chip in the first place and set baud_base to
921600, then we should do so again in the resume path.

This patch adds that code to serial8250_resume_port(), and also makes
serial8250_resume() actually call serial8250_resume_port() for each port
instead of just calling uart_resume_port() directly. And thus fixes
serial port operation after suspend/resume.

It also fixes a bogus comment where we write the EXCR2 register with a
comment saying /* EXCR1 */

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17 05:25:49 -07:00
wendy xiong
bc88d5d4e1 icom: add new sub-device-id to support new adapter
This patch add new sub-device-id to support new adapter and changed the
interrupt irq number for unsigned char to unsigned int.

[akpm@osdl.org: fix whitespace in device table]
Signed-off by: Wendy Xiong <wendyx@us.ibm.com>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17 05:23:05 -07:00
David Brownell
e40659c5ca rtc kconfig clarification
Make drivers/rtc/Kconfig be clearer about what the various "interfaces"
actually mean, by showing path names.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17 05:23:05 -07:00
David Brownell
558a40f708 rtc-omap build fix
Fix typo which breaks build.  How did that happen?

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17 05:23:05 -07:00
Gerd Hoffmann
a1a4849c41 Refine SCREEN_INFO sanity check for vgacon initialization
Refine SCREEN_INFO sanity check for vgacon initialization.

Checking video mode field only to see whenever SCREEN_INFO is
initialized is not enougth, in some cases it is zero although
a vga card is present.  Lets additionally check cols and lines.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17 05:23:04 -07:00
Aaron Durbin
f363d16fbb acpi: fix potential call to a freed memory section.
Strip __cpuinit[data] from Node <-> PXM routines and supporting data
structures.  Also make pxm_to_node_map and node_to_pxm_map local to the
numa acpi module.

This fixes a bug triggered by the following conditions:
- boot on a machine with a SLIT table defined
- kernel is configured w/ CONFIG_HOTPLUG_CPU=n
- cat /sys/devices/system/node/node*/distance
This will cause an oops by calling into a freed memory section.

In particular, on x86_64, __node_distance calls node_to_pxm().

Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17 05:23:04 -07:00
Christoph Lameter
a35afb830f Remove SLAB_CTOR_CONSTRUCTOR
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-17 05:23:04 -07:00
Stephen Rothwell
ccd308f09a [POWERPC] Remove build warnings in windfarm_core
drivers/macintosh/windfarm_core.c: In function 'wf_register_control':
drivers/macintosh/windfarm_core.c:219: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result
drivers/macintosh/windfarm_core.c: In function 'wf_register_sensor':
drivers/macintosh/windfarm_core.c:329: warning: ignoring return value of 'device_create_file', declared with attribute warn_unused_result

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-05-17 21:11:19 +10:00
Dave Jiang
40ebbcbf23 [POWERPC] Fix comment in booke_wdt
The early kernel parameter is wdt and not wdt_enable. according to
arch/powerpc/kernel/setup_32.c.

Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-05-17 21:10:15 +10:00
Linus Torvalds
b2cd64153b Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: track spindown status and skip spindown_compat if possible
  libata: fix shutdown warning message printing
  libata-acpi: add ATA_FLAG_ACPI_SATA port flag
  libata: during revalidation, check n_sectors after device is configured
  libata: separate out ata_dev_reread_id()
  pata_scc had been missed by ata_std_prereset() switch
2007-05-16 21:28:49 -07:00
Linus Torvalds
e0f88db302 Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Add hypervisor API negotiation and fix console bugs.
2007-05-16 21:19:45 -07:00
Andrew Morton
8382d2b9a7 parport_pc needs dma-mapping.h
alpha:

drivers/parport/parport_pc.c: In function 'parport_pc_fifo_write_block_dma':
drivers/parport/parport_pc.c:636: warning: implicit declaration of function 'dma_map_single'
drivers/parport/parport_pc.c:637: error: 'DMA_TO_DEVICE' undeclared (first use in this function)
drivers/parport/parport_pc.c:637: error: (Each undeclared identifier is reported only once
drivers/parport/parport_pc.c:637: error: for each function it appears in.)

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-16 21:19:15 -07:00
Domen Puncer
0a4dd7783d spi: fix spidev for >sizeof(long)/32 devices
find_first_zero_bit accepts number of bits, not longs.

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-16 21:19:15 -07:00
James Bottomley
cab537d609 [SCSI] aacraid: fix panic on short Inquiry
Unable to handle kernel paging request at ffff8101c0000000 RIP:
 [<ffffffff880b22a1>] :aacraid:aac_internal_transfer+0xd6/0xe3
PGD 8063 PUD 0
Oops: 0000 [1] SMP
last sysfs file: /block/sdb/removable
CPU 2
Modules linked in: autofs4(U) hidp(U) nfs(U) lockd(U)
fscache(U) nfs_acl(U) rfcomm(U) l2cap(U) bluetooth(U)
sunrpc(U) ipv6(U) cpufreq_ondemand(U) dm_mirror(U) dm_mod(U)
video(U) sbs(U) i2c_ec(U) button(U) battery(U) asus_acpi(U)
acpi_memhotplug(U) ac(U) parport_pc(U) lp(U) parport(U)
joydev(U) ide_cd(U) i2c_i801(U) i2c_core(U) shpchp(U)
cdrom(U) bnx2(U) sg(U) pcspkr(U) ata_piix(U) libata(U)
aacraid(U) sd_mod(U) scsi_mod(U) ext3(U) jbd(U) ehci_hcd(U)
ohci_hcd(U) uhci_hcd(U)
Pid: 2352, comm: syslogd Not tainted 2.6.18-prep #1
RIP: 0010:[<ffffffff880b22a1>]  [<ffffffff880b22a1>] :aacraid:aac_internal_transfer+0xd6/0xe3
RSP: 0000:ffff8101bfd1fe68  EFLAGS: 00010083
RAX: 0000000000000063 RBX: 0000000000000008 RCX: 00000000ffd1fea0
RDX: ffffffff802da628 RSI: ffff8101c0000000 RDI: ffff8101b2a08168
RBP: ffff8101b2728010 R08: ffffffff802da628 R09: 0000000000000046
R10: 0000000000000000 R11: 0000000000000080 R12: 0000000000000010
R13: ffff8101bfd1fea8 R14: ffff8101bc74df58 R15: ffff8101bc74df58
FS:  00002aaaab0146f0(0000) GS:ffff8101bfcd2e40(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff8101c0000000 CR3: 00000001bdecd000 CR4: 00000000000006e0
Process syslogd (pid: 2352, threadinfo ffff8101bc74c000, task ffff8101bd979040)
Stack:  0000000000000012 0000000000000036 0000000000000000 ffff8101bee9a800
 ffff8101be9d3a00 ffff8101be9d3a00 ffff8101be8014f8 ffffffff880b26cc
 40212227607e3141 2029282a26252423 0000000000000003 ffff810037e3a000
Call Trace:
 <IRQ [<ffffffff880b26cc>] :aacraid:get_container_name_callback+0x8b/0xb5
 [<ffffffff880b6f67>] :aacraid:aac_intr_normal+0x1b3/0x1f9
 [<ffffffff880b8007>] :aacraid:aac_rkt_intr+0x37/0x115
 [<ffffffff80099749>] __rcu_process_callbacks+0xf8/0x1a8
 [<ffffffff80010705>] handle_IRQ_event+0x29/0x58
 [<ffffffff800b2fe0>] __do_IRQ+0xa4/0x105
 [<ffffffff80011c19>] __do_softirq+0x5e/0xd5
 [<ffffffff8006a193>] do_IRQ+0xe7/0xf5
 [<ffffffff8005b649>] ret_from_intr+0x0/0xa

On digging into it, it turned out that the customer was probing an
aacraid device with an INQUIRY of 8 bytes.  The way aacraid works, it
was blindly trying to use aac_internal_transfer to copy the container
name to byte 16 of the inquiry data, resulting in a negative transfer
length.  It then copies over the whole of kernel memory before
dropping off the end.

Fix updated and corrected by Mark Salyzyn

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 18:16:13 -04:00
Salyzyn, Mark
2ab01efd1d [SCSI] aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1)
http://bugzilla.kernel.org/show_bug.cgi?id=8469

As discussed in the bugzilla outlined below, we have an sa based
(Mustang) RAID adapter on the system, a Dell PERC2/QC. Affected
controllers are HP NetRAID, Adaptec AAC-364, Dell PERC2/QC or Adaptec
5400S. This problem  coincides with the introduction of the adapter_comm
and adapter_deliver platform functions (Message [PATCH 1/4] aacraid:
rework communication support code, January 23 2007, which initially
migrated to 2.6.21)

The panic occurs with an uninitialized adapter_deliver platform function
pointer. The enclosed patch, unmodified as tested by Rainer, solves the
problem.

Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 13:06:26 -04:00
FUJITA Tomonori
bcd4e22540 [SCSI] tgt: fix a rdma indirect transfer error bug
This sets sg_dma_len to a proper value.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 12:45:17 -04:00
Ed Lin
c25da0afa7 [SCSI] stex: minor cleanup and version update
Add debug information into abort and host_reset routine.
Change ioremap to ioremap_nocache.
Version updated to 3.6.0000.1.

Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 12:41:39 -04:00
Ed Lin
d116a7bc6a [SCSI] stex: fix reset recovery for console device
After reset completed, the scsi error handler sends out TEST_UNIT_READY
to the device. For 'normal' devices the command will be handled by firmware.
However, because the RAID console only interfaces to scsi mid layer, the
firmware will not process the command for it. This will make the console to
be offlined right after reset. Add the handling in driver to fix this problem.

Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 12:41:23 -04:00
Ed Lin
69f4a51391 [SCSI] stex: extend hard reset wait time
During hard bus reset of st_shasta controllers, 1 ms is not enough for
16-port controllers, although it's good for 8-port controllers.  Extend the
wait time to 100  ms to allow bus resets finish successfully.

Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 12:40:51 -04:00
Ed Lin
e0b2e597d5 [SCSI] stex: fix id mapping issue
The correct internal mapping of stex controllers should be:
id:0~15, lun:0~7 (st_shasta)
id:0, lun:0~127 (st_yosemite)
id:0~127, lun:0 (st_vsc and st_vsc1)

This patch reports the internal mapping to scsi mid layer,  eliminating
the translation between scsi mid layer and firmware. To achieve this
goal, we also need to:
-- fail the REPORT_LUNS command for st_shasta because the
   firmware is known to not report all actual luns
-- add an entry in scsi_devindo.c to force sequential lun scan
   (for st_shasta controllers)
-- fail the REPORT_LUNS command for console device
-- remove special handling of REPORT_LUNS command for
   st_yosemite, as there is no translation mapping now

Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 12:40:21 -04:00
Brian King
5af23d263c [SCSI] ipr: Proper return codes for eh_dev_reset for SATA devices
Currently ipr always returns success from eh_dev_reset when
called for a SATA device. If ata_do_eh is unable to recover
for some reason, this can result in commands that are still
outstanding when ata_do_eh returns. Change ipr to verify no
commands are outstanding before returning success.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 12:39:33 -04:00
Andrew Victor
e45c7a4382 [ARM] 4378/1: KS8695: Serial driver fix
A fix for a really stupid typo in the KS8695 serial driver.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-05-16 15:35:25 +01:00
Michael Loehr
9f28745a6b [SCSI] zfcp: IO stall after deleting and path checker changes after reenabling zfcp devices
IO stall after deleting and path checker changes after reenabling zfcp device

Setting one zfcp device offline using chccwdev in a multipath
environment and waiting will lead to IO stall on all paths.
After setting the zfcp device back online using chccwdev,
the devices with io stall will have a different path checker.
Devices corresponding to the deleted units are never freed.
This has the effect that 'slave_destroy' is never called and zfcp
still thinks that this unit is registered
(ZFCP_STATUS_UNIT_REGISTERED is still set). Hence the erp
routine is not called correctly and the unit is not enabled properly.

Do not delete rport and the sdev. Just set the host to block on
'offline'. Setting host online again will then remove the blocked status
and everything is fine again.

Signed-off-by: Michael Loehr <mloehr2@linux.vnet.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 10:01:38 -04:00
Martin Peschke
869b2b444c [SCSI] zfcp: avoid clutter in erp_dbf
avoid clutter in erp_dbf

cleanup zfcp_fsf_req_dismiss functions:
- avoid clutter in erp_dbf (reqs_active is always 0)
- fold called three-line function into calling function
- add meaningful comment
- coding style

Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 10:01:38 -04:00
James Smart
a53eb5e060 [SCSI] FC Transport support for vports based on NPIV
This patch provides support for FC virtual ports based on NPIV.
For information on the interfaces and design, please read the
Documentation/scsi/scsi_fc_transport.txt file enclosed within
the patch.

The RFC was originally posted here:
http://marc.info/?l=linux-scsi&m=117226959918393&w=2

Changes from the initial RFC:
- Bug fix: needed a transport_class_unregister() for the vport class
- Create a symlink to the vport in the shost device if it is not the
    parent of the vport.
- Made symbolic name writable so it can be set after creation
- Made the temporary fc_vport_identifiers struct private to the
transport.
- Deleted the vport_id field from the vport. I couldn't find any good
  use for it (and symname is a good replacement).
- Made the vport_state and vport_last_state "private" attributes.
  Added the fc_vport_set_state() helper function to manage state
  transitions
- Updated vport_create() to allow a vport to be created in a disabled
  state.
- Added INITIALIZING and FAILED vport states
- Added VPCERR_xxx defines for errors to be returned from vport_create()
- Created a Documentation/scsi/scsi_fc_transport.txt file that describes
  the interfaces and expected LLDD behaviors.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-16 09:36:15 -04:00
Tejun Heo
13b8d09f5d libata: track spindown status and skip spindown_compat if possible
Our assumption that most distros issue STANDBYNOW seems wrong.  The
upstream sysvinit and thus many distros including gentoo and opensuse
don't take any action for libata disks on spindown.  We can skip
compat handling for these distros so that they don't need to update
anything to take advantage of kernel-side shutdown.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:31 -04:00
Tejun Heo
da071b42f7 libata: fix shutdown warning message printing
Unlocking ap->lock and ssleeping don't work because SCSI commands can
be issued from completion path without context.  Reimplement delayed
completion by allowing translation functions to override
qc->scsidone(), storing the original completion function to
scmd->scsi_done() and overriding qc->scsidone() with a function which
schedules delayed invocation of scmd->scsi_done().

This isn't pretty at all but all the ugly parts are thankfully
contained in the stop translation path where the compat feature is
implemented.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:31 -04:00
Tejun Heo
3cadbcc098 libata-acpi: add ATA_FLAG_ACPI_SATA port flag
Whether a controller needs IDE or SATA ACPI hierarchy is determined by
the programming interface of the controller not by whether the
controller is SATA or PATA, or it supports slave device or not.  This
patch adds ATA_FLAG_ACPI_SATA port flags which tells libata-acpi that
the port needs SATA ACPI nodes, and sets the flag for ahci and
sata_sil24.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:31 -04:00
Tejun Heo
6ddcd3b020 libata: during revalidation, check n_sectors after device is configured
Device might be resized during ata_dev_configure() due to HPA or
(later) ACPI _GTF.  Currently it's worked around by caching n_sectors
before turning off HPA.  The cached original size is overwritten if
the device is reconfigured without being hardreset - which always
happens after configuring trasnfer mode.  If the device gets hardreset
for some reason after that, revalidation fails with -ENODEV.

This patch makes size checking more robust by moving n_sectors check
from ata_dev_reread_id() to ata_dev_revalidate() after the device is
fully configured.  No matter what happens during configuration, a
device must have the same n_sectors after fully configured to be
treated as the same device.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:30 -04:00
Tejun Heo
fe30911b34 libata: separate out ata_dev_reread_id()
Separate out ata_dev_reread_id() from ata_dev_revalidate().
ata_dev_reread_id() reads IDENTIFY page and determines whether the
same device is still there.  ata_dev_revalidate() reconfigures after
reread completes.  This will be used by ACPI update.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:30 -04:00
Al Viro
d1c68fa6ce pata_scc had been missed by ata_std_prereset() switch
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:30 -04:00
David S. Miller
c7754d465b [SPARC64]: Add hypervisor API negotiation and fix console bugs.
Hypervisor interfaces need to be negotiated in order to use
some API calls reliably.  So add a small set of interfaces
to request API versions and query current settings.

This allows us to fix some bugs in the hypervisor console:

1) If we can negotiate API group CORE of at least major 1
   minor 1 we can use con_read and con_write which can improve
   console performance quite a bit.

2) When we do a console write request, we should hold the
   spinlock around the whole request, not a byte at a time.
   What would happen is that it's easy for output from
   different cpus to get mixed with each other.

3) Use consistent udelay() based polling, udelay(1) each
   loop with a limit of 1000 polls to handle stuck hypervisor
   console.

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-15 20:23:02 -07:00
Al Viro
8eafafb54b rpadlpar breakage - fallout of struct subsystem removal
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 18:56:37 -07:00
Al Viro
1b2bad2f04 em28xx and ivtv should depend on PCI
.. because video-buf.c requires PCI, and VIDEO_EM28XX selects it.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 18:56:37 -07:00
Al Viro
9cbe05c712 missing includes in mlx4
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 18:56:37 -07:00
Al Viro
7a86edef39 missing dependencies for USB drivers in input
stuff that does select USB should depend on USB_ARCH_HAS_HCD, or we'll
end up with unbuildable configs.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 18:56:37 -07:00
Al Viro
faa2fb4e67 missing mm.h in fw-ohci
need it for page_private(), not all targets have it pulled indirectly

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-15 18:56:37 -07:00
Linus Torvalds
e089d43fb1 Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  Use menuconfig objects: IDE
  sl82c105: Switch to ref counting API
  ide: remove ide_use_dma()
  ide: add missing validity checks for identify words 62 and 63
  ide: remove ide_dma_enable()
  sl82c105: add speedproc() method and MWDMA0/1 support
  cs5530/sc1200: add ->speedproc support
  cs5530/sc1200: DMA support cleanup
  ide: use ide_tune_dma() part #2
  cs5530/sc1200: add ->udma_filter methods
  ide: always disable DMA before tuning it
  pdc202xx_new: use ide_tune_dma()
  alim15x3: use ide_tune_dma()
  sis5513: PIO mode setup fixes
  serverworks: PIO mode setup fixes
  pdc202xx_old: rewrite mode programming code (v2)
2007-05-15 18:47:21 -07:00
Jan Engelhardt
e0ff9cd12a Use menuconfig objects: IDE
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.

Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Alan Cox
640b31bf12 sl82c105: Switch to ref counting API
Not sure how this one got missed in the great purge some time ago but it did.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
122ab0887c ide: remove ide_use_dma()
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.

There should be no functionality changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
3649c06e66 ide: add missing validity checks for identify words 62 and 63
Check validity of identify words 62 and 63 before using them in
ide_get_mode_mask().

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Bartlomiej Zolnierkiewicz
4728d546d7 ide: remove ide_dma_enable()
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:46 +02:00
Sergei Shtylyov
46cedc9b77 sl82c105: add speedproc() method and MWDMA0/1 support
Add the speedproc() method for setting transfer modes, modify config_for_dma()
to call it and use ide_max_dma_mode() to select the best DMA mode.
Add support for the multiword DMA modes 0 and 1, using the upper half of the
'drive_data' field to store the DMA timings to program into the drive control
register when DMA is turned on for real.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2007-05-16 00:51:44 +02:00