New module parameters have been added to nandsim to
simulate:
bitflips random bit flips
badblocks blocks that are initially marked bad
weakblocks blocks that fail to erase after a
small number of erase cycles
weakpages pages that fail to write after a
small number of successful writes
gravepages pages that fail to read after a
small number of successful reads
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Enhance nandsim to be able to create more than 1 partition.
A new module parameter 'parts' may be used to specify partition
sizes.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.
Tested only on AT26F004.
Signed-off-by: Hans-Jürgen Koch <hjk@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The ops.len member is not initialized, because it is unused for this
operation. The length check needs to use ops.ooblen instead
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
o A dependency on the processor architecture does not make sense;
delete it.
o The Alchemy and MTX drivers requires MTD_PARTITIONS and MTD_CFI to work,
make those dependencies.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In mthca_arbel_fmr_unmap(), the high bits of the key are masked off.
This gets rid of the effect of adjust_key(), which makes sure that
bits 3 and 23 of the key are equal when the Sinai throughput
optimization is enabled, and so it may happen that an FMR will end up
with bits 3 and 23 in the key being different. This causes data
corruption, because when enabling the throughput optimization, the
driver promises the HCA firmware that bits 3 and 23 of all memory keys
will always be equal.
Fix by re-applying adjust_key() after masking the key.
Thanks to Or Gerlitz for reproducing the problem, and Ariel Shahar for
help in debug.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We only map DMA when cmd->request_bufflen is non-zero for non-sg
buffers, we thus should make the same check when unmapping.
Based upon a report from Pasi Pirhonen.
Signed-off-by: David S. Miller <davem@davemloft.net>
3w-xxxx emulates a REQUEST_SENSE response by simply returning nothing.
Unfortunately, it's assuming that the REQUEST_SENSE command is
implemented with use_sg == 0, which is no longer the case. The oops
occurs because it's clearing the scatterlist in request_buffer instead
of the memory region.
This is fixed by using tw_transfer_internal() to transfer correctly to
the scatterlist.
Acked-by: adam radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
DVB USB remotes do not support changing keycode maps but set
input_dev->keycodesize and input_dev->keycodemax without setting
input_dev->keycode. This causes kernel oops when user tries to
look up (or change) current keymap.
While the proper fix would be to make remotes handle keymap changes
we'll just remove keycodemax and keycodesize initialization so
EVIOCGKEYCODE and EVIOCSKEYCODE will simply return -EINVAL.
http://bugzilla.kernel.org/show_bug.cgi?id=8312
Signed-off-by: olaf.kirch@oracle.com
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If 'num_pages' were ever 1 more than a multiple of 8 (32bit platforms)
or of 16 (64 bit platforms). filemap_attr would be allocated one
'unsigned long' shorter than required. We need a round-up in there.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The firmware assigns irq 20/21 to the VIA IDE device on Pegasos.
But the required interrupt is 14/15.
Maybe someone confused decimal vs. hexadecimal values.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the buf pointer is advanced too far during each iteration.
Also terminate the string with a newline.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows the PMU LED on both a PowerMac 7,2 (Dual G5 2.0GHz, June 2003)
and a PowerMac 7,3 (Dual G5 2.0GHz, June 2004) to be controlled.
The physical LED is never off, unlike an iBook/PowerBook LED.
It is rather dim ("off") or very bright ("on").
Signed-off-by: Tony Vroon <chainsaw@gentoo.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The generation of the uevent is now common to all bus using
of_device.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As of commit 6cdbd77e ("cxgb3 - missing CPL hanler and register
setting."), the cxgb3 ethernet NIC driver no longer handles SET_TCB
replies, so we need to do it in the iWARP driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It appears that if we turn on 6-byte Lifebook protocol on
Panasonic CF-28 its touchpad is left alone and generates
standard 3-byte PS/2 data stream with relative packets
instead of being converted in 3-byte Lifebook protocol with
absolute coordinates - in other words what get what we need
to distinguish between touchscreen and touchpad.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Panasonic CF18 has an active multiplexing controller with
touchscreen connected to one port and a touchpad to another.
Use "phys" from serio port to activate lifebook protoocol
only on the port that has touchscreen connected to it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Create platform device for cobalt buttons as part of arch setup.
This makes the driver follow current driver model more closely.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
ati_remote causes repeats after only .23 seconds with my remote and
makes it hard to use comfortably. Make a precise way of setting the
repeat delay time in milliseconds and default it to 500ms. The old
behavior can be had by setting repeat_delay = 0.
Signed-off-by: Karl Pickett <karl.pickett@gmail.com>
Signed-off-by: Vincent Vanackere <vincent.vanackere@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
IRQF_DISABLED is the proper name.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds module parameters for several timing values used
in the driver. These values can vary based on the hardware design
and how much capacitive filtering there is on the touch panel inputs,
and the resistance of the panel.
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation to switching to struct device and class device
going away provide an alias to allow drivers that create devices
to use either input_dev->cdev.dev or input_dev->dev.parent to
put them into sysfs tree. The former will go away once conversion
to struct device is complete.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>