Current 2.6.21 libata does the following:
void ata_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
tf->command = ata_check_status(ap);
...
if (tf->flags & ATA_TFLAG_LBA48) {
iowrite8(tf->ctl | ATA_HOB, ioaddr->ctl_addr);
tf->hob_feature = ioread8(ioaddr->error_addr);
...
}
}
...
static void fill_result_tf(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
ap->ops->tf_read(ap, &qc->result_tf);
qc->result_tf.flags = qc->tf.flags;
}
Based on this, those last two statements fill_result_tf()
appear to me to be in the wrong order, in that the tf->flags
are uninitialized at the point where tf_read() is invoked.
So for lba48 commands, tf_read() won't be reading back the
full lba48 register contents..
Correct?
This patch corrects fill_result_tf() so that the flags
get copied to result_tf before they are used by tf_read().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you set the IFF_ALLMULTI flag on a b44 device, or if you join more than
B44_MCAST_TABLE_SIZE multicast groups, the device will stop receiving unicast
messages. This is because the __b44_set_mac_addr call sets the zeroth CAM
entry to the MAC address of the device, and then the loop at line 1722
proceeds to overwrite it unless the value of i is set by the __b44_load_mcast
call. However, when IFF_ALLMULTI is set, that call is bypassed, leaving i set
to zero.
Fixed by starting the loop at 1 to make it skip the CAM entry for the MAC
address.
Signed-off-by: Bill Helfinstine <bhelf@flitterfly.whirpon.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Run the watchdog task when the link is up.
Flush the XGMAC Tx FIFO when the link drops.
Also remove a statistics update that should have gone
in the previous modification of xgmac.c.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Differentiate NIC only adapters from RNICs.
Initialize offload capabilities for RNICs only.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a simplified and actually more comprehensive form of a bug
fix from Mitch Williams <mitch.a.williams@intel.com>.
When we mask or unmask a msi-x irqs the writes may be posted because
we are writing to memory mapped region. This means the mask and
unmask don't happen immediately but at some unspecified time in the
future. Which is out of sync with how the mask/unmask logic work
for ioapic irqs.
The practical result is that we get very subtle and hard to track down
irq migration bugs.
This patch performs a read flush after writes to the MSI-X table for mask
and unmask operations. Since the SMP affinity is set while the interrupt
is masked, and since it's unmasked immediately after, no additional flushes
are required in the various affinity setting routines.
The testing by Mitch Williams on his especially problematic system should
still be valid as I have only simplified the code, not changed the
functionality.
We currently have 7 drivers: cciss, mthca, cxgb3, forceth, s2io,
pcie/portdrv_core, and qla2xxx in 2.6.21 that are affected by this
problem when the hardware they driver is plugged into the right slot.
Given the difficulty of reproducing this bug and tracing it down to
anything that even remotely resembles a cause, even if people are
being affected we aren't likely to see many meaningful bug reports, and
the people who see this bug aren't likely to be able to reproduce this
bug in a timely fashion. So it is best to get this problem fixed
as soon as we can so people don't have problems.
Then if people do have a kernel message stating "No irq for vector" we
will know it is yet another novel cause that needs a complete new
investigation.
Cc: Greg KH <greg@kroah.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SCSI]: Fix scsi_send_eh_cmnd scatterlist handling
[SPARC]: Add unsigned to unused bit field in a.out.h
This fixes a regression caused by commit:
2dc611de5a
The sense buffer code in scsi_send_eh_cmnd was changed to use
alloc_page() and a scatter list, but the sense data copy was not
updated to match so what we actually get in the sense buffer is total
grabage starting with the kernel address of the struct page we got.
Basically the stack frame of scsi_send_eh_cmd() is what ends up
in the sense buffer.
Depending upon how pointers look on a given platform, you can
end up getting sr_ioctl.c errors when you mount a cdrom. If
the CDROM gives a check condition for GPCMD_GET_CONFIGURATION issued
by drivers/cdrom/cdrom.c:cdrom_mmc_profile(), sr_ioctl will
spit out this error message in sr_do_ioctl() with the way pointers
are on sparc64:
default:
printk(KERN_ERR "%s: CDROM (ioctl) error, command: ", cd->cdi.name);
__scsi_print_command(cgc->cmd);
scsi_print_sense_hdr("sr", &sshdr);
err = -EIO;
This is the error Tom Callaway reported in:
http://marc.info/?l=linux-sparc&m=117407453208101&w=2
Anyways, fix this by using page_address(sgl.page) which is OK
because we know this is low-mem due to GFP_ATOMIC.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Christoph Hellwig <hch@lst.de>
The nvram dword alignment logic was broken when writing less than 4
bytes on a non-aligned offset. It was missing logic to round the
length to 4 bytes.
The page erase code is also moved so that it is only called when
using non-buffered flash for better code clarity.
Update version to 1.5.7.
Based on initial patch from Tony Cureington <tony.cureington@hp.com>.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto unlock sectors on resume for auto locking flash on power up.
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add flash and rootfs mappings for the PMC-Sierra MSP71xx devices.
This patch references some platform support files previously submitted to
the linux-mips@linux-mips.org list.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On a multiprocessor machine the VT_WAITACTIVE ioctl call may return 0 if
fg_console has already been updated in redraw_screen() but the console
switch itself hasn't been completed. Fix this by checking fg_console in
vt_waitactive() with the console sem held.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lockdep reported cmos_suspend() and cmos_resume() calling rtc_update_irq()
with IRQs enabled; not allowed.
Also fix problems seen on some hardware, whereby false alarm IRQs could be
reported (primarily to userspace); and update two comments to match changes
in ACPI. Those make up most of this patch, by volume.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change PnP resource handling code to use proper type for resource start and
length. Fixes bogus regions reported in /proc/iomem.
I've also made some pointer constant, as they are constant...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an off-by-one spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ADEF bits in the TSCR register have different meanings in read and
write mode. For this reason ADEF has to be reset on every
read-modify-write operation.
This patch introduces a special write function for this register, which
takes care of it.
Thanks to Holger Magnussen for pointing my nose at this problem.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Setting the message length to zero means to send one byte, so you need a
subtraction instead of an addition.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch addresses the following issues with the pxa2xx FIr driver:
1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.
Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ingo reported that built-in drivers suffered bootup hangs with certain
driver unregistry sequences, due to sysfs breakage.
Do the minimal fix for v2.6.21: only wait if the driver is a module.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Attached is the patch I feel will address this issue. As an added
'perk' I have also added the code to detect if the controller was
previously initialized for interrupted operations by ANY operating
system should the reset_devices kernel parameter not be set and we are
dealing with a naïve kexec without the addition of this kernel
parameter. The reset handler is also improved. Related to reset
operations, but not pertinent specifically to this issue, I have also
altered the handling somewhat so that we reset the adapter if we feel
it is taking too long (three minutes) to start up.
We have not unit tested the reset_devices flag propagation to this
driver code, nor have we unit tested the check for the interrupted
operations under the conditions of a naively issued kexec. We are
submitting this modified driver to our Q/A department for integration
testing in our current programs. I would appreciate an ACK to this
patch should it resolve the issue described in this thread...
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Improve overall command performance by embedding the scatterlist
in the command block used by the adapter. This decreases
the overall number of DMAs required for a single command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qc_issue fails for some reason, return a better error
to libata.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add entry in ipr error translation table for an error
received when a device is forced into the failed state
by the user.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add the ability to control how much error data gets logged
on a per error basis.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix to make sure user config accesses get re-enabled if the
PCI config write to start BIST fails.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a problem discovered on a system with some
bad SATA devices attached. If a command to a SATAPI device
times out and the device gets reset as part of error recovery,
its possible that ipr will set err_mask to indicate a device
error has occurred. If this happens, a request sense will get
issued by libata. Since scsi core thinks this scsi command is
now completed, because the device reset handler completed successfully,
scsi core will free the associated scsi command, which may
cause an oops when that request sense is completed later
by ipr. This patch ensures that any commands that get aborted
as a result of a device reset set err_mask appropriately so
that the request sense does not get sent.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For ipr SAS adapters that support dual pathing, this
patch modifies ipr to log an error when a path fails.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ipr driver has a sysfs attribute which can be used to
adjust the logging level of the driver for error events.
The error response data for commands can be dumped by
increasing the logging level of the ipr driver. This
currently only works for JBOD passthrough devices.
This patch enables this function for all devices, including
RAID devices, to aid in debugging problems.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds support for some new PCI-E ipr adapters.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the auto RAID 0 array creation module parameter, since
support for this function has been removed from the firmware.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some ipr adapters may take longer than others to come operational.
This patch makes this timeout different for different adapters,
while still preserving the module parameter which can be used
to globally override the default.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed the kernel-doc comment for ibmvscsi_slave_configure. Thanks to
Randy Dunlap for pointing this out.
Adding a slave_configure function for the driver. Now the disks can be
restarted by the scsi mid-layer when the are disconnected and reconnected.
Signed-off-by: "Robert Jennings" <rcj@linux.vnet.ibm.com>
Signed-off-by: "Santiago Leon" <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The request limit calculations used previously on the client failed to
mirror the state of the server. Additionally, when a value < 3 was provided
there could be problems setting can_queue and handling abort and reset
commands.
Signed-off-by: "Robert Jennings" <rcj@linux.vnet.ibm.com>
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Adapter build date that is to be printed on instantiation was not
displayed as a result of the supplemental adapter information structure
not being in sync with the Firmware; the driver took an early test cycle
version that had a miss-sized padded region at the head and the
structure was not re-checked at the end of qualification. The Build Date
was not a priority and is merely a cosmetic enhancement, and the wrong
location for the start of the structure member would not induce any
side-effect problems. We updated the structure to match the actual
format, and added the TSID (Tech Support Identification) value print,
should it be present, to the adapter instantiation announcements during
driver load.
This later enhancement should improve the relationship between Service
folk & Tech Support if the printed value of the TSID found it's way into
the circular file labeled G...
Neither of these values show in sysfs (yet).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Just sweeping the floor clean in one spot. Some of these constants have
never been used in the driver or in the firmware (and thus are
meaningless). Triggered this patch because I discovered one of the
unused constants was actually incorrect and figured it was better to
clean them out than correct and update. There are no side effects at all
regarding this patch, it is purely cosmetic.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On the path qla2x00_probe_one() -> probe_failed -> qla2x00_free_device(),
pci_disable_device() is executed twice, once in qla2x00_free_device()
and once in qla2x00_probe_one().
This patch removes the unnecessary call.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Unsigned long is not always the same size as a pointer, namely on 32 bit
systems with 64 bit address space. Ptrdiff_t is the same size as a
pointer in all configurations. By using ptrdiff_t we can mitigate the
warning messages on these configurations. There should be no side
effects of this patch.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- proper prototypes for global code in aacraid.h
- aac_rx_start_adapter() can now become static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker spotted this dead code introduced by
commit a07f353701.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the unused SCSI-related kernel config variables
SCSI_NCR53C8XX_PROFILE_SUPPORT
SCSI_NCR53C8XX_PROFILE
53C700_IO_MAPPED
AIC79XX_ENABLE_RD_STRM
AIC7XXX_PROBE_EISA_VL
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>