Found by manual code inspection.
Tested: compile, reboot, ethtool -d ethX
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA. The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).
Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tearing down a net namespace, ipv4 mr_table structures are freed
without first deactivating their timers. This can result in a crash in
run_timer_softirq.
This patch mimics the corresponding behaviour in ipv6.
Locking and synchronization seem to be adequate.
We are about to kfree mrt, so existing code should already make sure that
no other references to mrt are pending or can be created by incoming traffic.
The functions invoked here do not cause new references to mrt or other
race conditions to be created.
Invoking del_timer_sync guarantees that ipmr_expire_timer is inactive.
Both ipmr_expire_process (whose completion we may have to wait in
del_timer_sync) and mroute_clean_tables internally use mfc_unres_lock
or other synchronizations when needed, and they both only modify mrt.
Tested in Linux 3.4.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the way device tree support is added in mdio-gpio
driver. I found lot of code duplication which is not necessary.
Also strangely a new platform driver was also introduced for device tree
support. All this forced me to do this cleanup patch.
After this patch, the driver probe checks the of_node pointer to get the
data from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds dummy functions in of_mdio.h, so that driver need not
ifdef there code with CONFIG_OF.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's fill IP header ident field with a meaningful value,
it might help some setups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid to use synchronize_rcu in l2tp_tunnel_free because context may be
atomic.
Signed-off-by: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit -
"b852b72 gianfar: fix bug caused by
87c288c6e9"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're hitting bug while trying to reinsert an already existing
expectation:
kernel BUG at kernel/timer.c:895!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
<IRQ>
[<ffffffffa0069563>] nf_ct_expect_related_report+0x4a0/0x57a [nf_conntrack]
[<ffffffff812d423a>] ? in4_pton+0x72/0x131
[<ffffffffa00ca69e>] ip_nat_sdp_media+0xeb/0x185 [nf_nat_sip]
[<ffffffffa00b5b9b>] set_expected_rtp_rtcp+0x32d/0x39b [nf_conntrack_sip]
[<ffffffffa00b5f15>] process_sdp+0x30c/0x3ec [nf_conntrack_sip]
[<ffffffff8103f1eb>] ? irq_exit+0x9a/0x9c
[<ffffffffa00ca738>] ? ip_nat_sdp_media+0x185/0x185 [nf_nat_sip]
We have to remove the RTP expectation if the RTCP expectation hits EBUSY
since we keep trying with other ports until we succeed.
Reported-by: Rafal Fitt <rafalf@aplusc.com.pl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.
This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When moving a net device from one net namespace to another
net namespace,dev_change_net_namespace calls NETDEV_DOWN
event,so the original net namespace's dst entries which
beloned to this net device will be put into dst_garbage
list.
then dev_change_net_namespace will set this net device's
net to the new net namespace.
If we unregister this net device's driver, this will trigger
the NETDEV_UNREGISTER_FINAL event, dst_ifdown will be called,
and get this net device's dst entries from dst_garbage list,
put these entries' dev to the new net namespace's lo device.
It's not what we want,actually we need these dst entries hold
the original net namespace's lo device,this incorrect device
holding will trigger emg message like below.
unregister_netdevice: waiting for lo to become free. Usage count = 1
so we should call NETDEV_UNREGISTER_FINAL event in
dev_change_net_namespace too,in order to make sure dst entries
already in the dst_garbage list, we need rcu_barrier before we
call NETDEV_UNREGISTER_FINAL event.
With help form Eric Dumazet.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
nothing too shocking or different."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
gma500: Consider CRTC initially active.
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm: Check for invalid cursor flags
drm: Initialize object type when using DRM_MODE() macro
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Before:
testing speed of ctr(aes) encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 206 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 244 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 360 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 814 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 5021 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 206 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 240 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 378 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 939 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 6395 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 209 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 249 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 414 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1073 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 7110 cycles (8192 bytes)
testing speed of ctr(aes) decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 225 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 233 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 344 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 810 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 5021 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 206 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 240 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 376 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 938 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 6380 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 214 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 251 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 411 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1070 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 7114 cycles (8192 bytes)
After:
testing speed of ctr(aes) encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 211 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 246 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 344 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 799 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 4975 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 210 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 236 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 365 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 888 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 6055 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 209 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 255 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 404 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1010 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 6669 cycles (8192 bytes)
testing speed of ctr(aes) decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 210 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 233 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 340 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 818 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 4956 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 206 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 239 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 361 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 888 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 5996 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 214 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 248 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 395 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 1010 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 6664 cycles (8192 bytes)
Signed-off-by: David S. Miller <davem@davemloft.net>
Before:
testing speed of ecb(aes) decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 223 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 230 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 325 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 719 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 4266 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 211 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 234 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 353 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 808 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 5344 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 214 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 243 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 393 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 939 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 6039 cycles (8192 bytes)
After:
testing speed of ecb(aes) decryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 226 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 231 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 313 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 681 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 3964 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 205 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 240 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 341 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 770 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 5050 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 216 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 250 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 371 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 869 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 5494 cycles (8192 bytes)
Signed-off-by: David S. Miller <davem@davemloft.net>
k1212MinADCSens and k1212MaxADCSens are defined wrongly.
The max must be greater than the min by obvious reason.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46561
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AES opcodes have a 3 cycle latency, so by doing 32-bytes at a
time we avoid a pipeline bubble in between every round.
For the 256-bit key case, it looks like we're doing more work in
order to reload the KEY registers during the loop to make space
for scarce temporaries. But the load dual issues with the AES
operations so we get the KEY reloads essentially for free.
Before:
testing speed of ecb(aes) encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 264 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 231 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 329 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 715 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 4248 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 221 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 234 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 359 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 803 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 5366 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 209 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 255 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 379 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 938 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 6041 cycles (8192 bytes)
After:
testing speed of ecb(aes) encryption
test 0 (128 bit key, 16 byte blocks): 1 operation in 266 cycles (16 bytes)
test 1 (128 bit key, 64 byte blocks): 1 operation in 256 cycles (64 bytes)
test 2 (128 bit key, 256 byte blocks): 1 operation in 305 cycles (256 bytes)
test 3 (128 bit key, 1024 byte blocks): 1 operation in 676 cycles (1024 bytes)
test 4 (128 bit key, 8192 byte blocks): 1 operation in 3981 cycles (8192 bytes)
test 5 (192 bit key, 16 byte blocks): 1 operation in 210 cycles (16 bytes)
test 6 (192 bit key, 64 byte blocks): 1 operation in 233 cycles (64 bytes)
test 7 (192 bit key, 256 byte blocks): 1 operation in 340 cycles (256 bytes)
test 8 (192 bit key, 1024 byte blocks): 1 operation in 766 cycles (1024 bytes)
test 9 (192 bit key, 8192 byte blocks): 1 operation in 5136 cycles (8192 bytes)
test 10 (256 bit key, 16 byte blocks): 1 operation in 206 cycles (16 bytes)
test 11 (256 bit key, 64 byte blocks): 1 operation in 268 cycles (64 bytes)
test 12 (256 bit key, 256 byte blocks): 1 operation in 368 cycles (256 bytes)
test 13 (256 bit key, 1024 byte blocks): 1 operation in 890 cycles (1024 bytes)
test 14 (256 bit key, 8192 byte blocks): 1 operation in 5718 cycles (8192 bytes)
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_SND_HDA_POWER_SAVE is no longer an experimental feature and its
behavior can be well controlled via the default value and module
parameter. Let's just replace it with the standard CONFIG_PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec provides its own set_power_state op, the D3-clock-stop
isn't checked correctly. And the recent changes for repeating the
state-setting operation isn't applied to such a codec, too.
This patch fixes these issues by moving the call of codec's own op to
the place where the generic power-set operation is done, and move the
power-state synchronization code out of
snd_hda_set_power_state_to_all() so that it can be called always at
the end of power-up/down sequence, and updates the D3 clock-stop flag
properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the HD-audio is removed, it leaves the refcounts when codecs are
powered up (usually yes) in the destructor. For fixing the unbalance,
and cleaning up the code mess, this patch changes the following:
- change pm_notify callback to take the explicit power on/off state,
- check of D3 stop-clock and keep_link_on flags is moved to the caller
side,
- call pm_notify callback in snd_hda_codec_new() and snd_hda_codec_free()
so that the refcounts are proprely updated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Attempting to run 'firmware_install' with CONFIG_USB_SERIAL_TI=y when
using make 3.82 results in an error
make[2]: *** No rule to make target `/lib/firmware/./', needed by
`/lib/firmware/ti_3410.fw'. Stop.
It turns out make 3.82 is picky when matching directory names with
trailing slashes as a result, where make 3.81 would handle this
correctly make 3.82 does not find the rule needed to create the
directory.
The './' seen in the error is added by $(dir) for firmware which
resides in the base firmware src directory, such as
ti_3410.fw.ihex. By performing $(dir) after we prepend the
$(INSTALL_FW_PATH) we can ensure we don't end up with a './' in the
middle of the path and the directory will be properly created.
This change works with make 3.81 and should work with previous
versions as well.
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Since commit d0e1e09568 initscr() is called twice in mconf.
Do it only in init_dialog() in util.c and there also save the
cursor position for the signal handler in mconf.c.
Signed-off-by: Dirk Gouders <gouders@et.bocholt.fh-gelsenkirchen.de>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Commit e9ba389c5 ("ALSA: usb-audio: Fix scheduling-while-atomic bug in
PCM capture stream") fixed a scheduling-while-atomic bug that happened
when snd_usb_endpoint_start was called from the trigger callback, which
is an atmic context. However, the patch breaks the idea of the endpoints
reference counting, which is the reason why the driver has been
refactored lately.
Revert that commit and let snd_usb_endpoint_start() take care of the URB
cancellation again. As this function is called from both atomic and
non-atomic context, add a flag to denote whether the function may sleep.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dummy_supplies for smsc911x are registered as "smsc911x".
smsc911x driver needs id = -1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.
In commit bc42aabc [2]
commit bc42aabc6a
Author: Adam Jackson <ajax@redhat.com>
Date: Wed May 23 16:26:54 2012 -0400
drm/edid/quirks: ViewSonic VA2026w
Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.
All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.
Please note that this monitor only has a VGA (D-Sub) connector [1].
[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add IPv6 support to the SIP NAT helper. There are no functional differences
to IPv4 NAT, just different formats for addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add inet_proto_csum_replace16 for incrementally updating IPv6 pseudo header
checksums for IPv6 NAT.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: David S. Miller <davem@davemloft.net>
Convert the IPv4 NAT implementation to a protocol independent core and
address family specific modules.
Signed-off-by: Patrick McHardy <kaber@trash.net>
For mangling IPv6 packets the protocol header offset needs to be known
by the NAT packet mangling functions. Add a so far unused protoff argument
and convert the conntrack and NAT helpers to use it in preparation of
IPv6 NAT.
Signed-off-by: Patrick McHardy <kaber@trash.net>
The NAT helpers currently only handle IPv4 packets correctly. Restrict
invocation of the helpers to IPv4 in preparation of IPv6 NAT.
Signed-off-by: Patrick McHardy <kaber@trash.net>
ICMPv6 error messages are tracked by extracting the conntrack tuple of
the inner packet and looking up the corresponding conntrack entry. Tuple
extraction uses the ->get_l4proto() callback, which in case of fragments
returns NEXTHDR_FRAGMENT instead of the upper protocol, even for the
first fragment when the entire next header is present, resulting in a
failure to find the correct connection tracking entry.
This patch changes ipv6_get_l4proto() to use ipv6_skip_exthdr() instead
of nf_ct_ipv6_skip_exthdr() in order to skip fragment headers when the
fragment offset is zero.
Signed-off-by: Patrick McHardy <kaber@trash.net>
The IPv6 conntrack fragmentation currently has a couple of shortcomings.
Fragmentes are collected in PREROUTING/OUTPUT, are defragmented, the
defragmented packet is then passed to conntrack, the resulting conntrack
information is attached to each original fragment and the fragments then
continue their way through the stack.
Helper invocation occurs in the POSTROUTING hook, at which point only
the original fragments are available. The result of this is that
fragmented packets are never passed to helpers.
This patch improves the situation in the following way:
- If a reassembled packet belongs to a connection that has a helper
assigned, the reassembled packet is passed through the stack instead
of the original fragments.
- During defragmentation, the largest received fragment size is stored.
On output, the packet is refragmented if required. If the largest
received fragment size exceeds the outgoing MTU, a "packet too big"
message is generated, thus behaving as if the original fragments
were passed through the stack from an outside point of view.
- The ipv6_helper() hook function can't receive fragments anymore for
connections using a helper, so it is switched to use ipv6_skip_exthdr()
instead of the netfilter specific nf_ct_ipv6_skip_exthdr() and the
reassembled packets are passed to connection tracking helpers.
The result of this is that we can properly track fragmented packets, but
still generate ICMPv6 Packet too big messages if we would have before.
This patch is also required as a precondition for IPv6 NAT, where NAT
helpers might enlarge packets up to a point that they require
fragmentation. In that case we can't generate Packet too big messages
since the proper MTU can't be calculated in all cases (f.i. when
changing textual representation of a variable amount of addresses),
so the packet is transparently fragmented iff the original packet or
fragments would have fit the outgoing MTU.
IPVS parts by Jesper Dangaard Brouer <brouer@redhat.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Cleaning up the IPv6 MTU checking in the IPVS xmit code, by using
a common helper function __mtu_check_toobig_v6().
The MTU check for tunnel mode can also use this helper as
ntohs(old_iph->payload_len) + sizeof(struct ipv6hdr) is qual to
skb->len. And the 'mtu' variable have been adjusted before
calling helper.
Notice, this also fixes a bug, as the the MTU check in ip_vs_dr_xmit_v6()
were missing a check for skb_is_gso().
This bug e.g. caused issues for KVM IPVS setups, where different
Segmentation Offloading techniques are utilized, between guests,
via the virtio driver. This resulted in very bad performance,
due to the ICMPv6 "too big" messages didn't affect the sender.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
