Move iop33x and iop32x PCI to fixed i/o mapping and remove io.h. This
changes the PCI bus addresses from the cpu address to 0 based. It appears
that there is translation h/w for this, but its untested.
Not sure what to do with io_offset. I think it should always be 0.
AFAICT, PCI setup is skipped if the ATU is already setup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move mv78xx0 PCI to fixed i/o mapping and remove io.h. This changes the PCI
bus addresses from the cpu address to 0 based. It appears that there is
translation h/w for this, but its untested.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move iop13xx PCI to fixed i/o mapping and remove io.h.
This changes the PCIe bus address to start at 0x10000. Let's hope this
works. If it does not, the alternative would be to revert the value we
write into OIOTVR to zero and set sys->io_offset to 64K.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
iop13xx confuses I/O port numbers with physical addresses, which breaks
legacy ISA I/O access behind PCI bridges and makes it unnecessarily hard
to unify the inb/outb accessors with other platforms. This removes the
special-casing and just puts all I/O ports into a single 128KB virtually
mapped I/O port range starting at port zero.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move orion5x PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move kirkwood PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The i/o regions are changed from 1MB to 64KB. It's likely that the 2nd
bus is not setup correctly.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move footbridge PCI to fixed i/o mapping. io.h is still needed for the
!MMU case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert shark to use the fixed i/o mapping and remove io.h.
This shrinks the mapping from 256MB to 1MB, but nothing is using that much
space AFAICT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move tegra PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
With consolidation of the PCI i/o mappings, the i/o space is being
set to start at a PCI bus addr of 0x0 and fixed to 64K per bus. In
this case the core ARM PCI setup code can setup the i/o resource.
Currently, the resource is only setup if the platform did not setup
an i/o resource.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Default CoreNet Coherency Bus (CCB) frequency on P3041 is 750MHz, but espi
cannot work at 40MHz with this CCB frequency, so we need to slow down the
clock rate of espi to 35MHz to make it work stable at the CCB frequency.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Typically, the return value desired for the failure of a
function with an integer return value is a negative integer. In
these cases, the return value is sometimes a negative integer
and sometimes 0, due to a subsequent initialization of the
return variable within the loop.
A simplified version of the semantic match that finds this
problem is: (http://coccinelle.lip6.fr/)
//<smpl>
@r exists@
identifier ret;
position p;
constant C;
expression e1,e3,e4;
statement S;
@@
ret = -C
... when != ret = e3
when any
if@p (...) S
... when any
if (\(ret != 0\|ret < 0\|ret > 0\) || ...) { ... return ...; }
... when != ret = e3
when any
*if@p (...)
{
... when != ret = e4
return ret;
}
//</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Link: http://lkml.kernel.org/r/1342284188-19176-7-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Sandy Bridge processors follow the SDM (Vol 3B, Table 15-20) and
set both the RIPV and EIPV bits in the MCG_STATUS register to
zero for machine checks during instruction fetch. This is more
than a little counter-intuitive and means that Linux cannot
recover from these errors. Rather than insert special case code
at several places in mce.c and mce-severity.c, we pretend the
EIPV bit was set for just this case early in processing the
machine check.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/180a06f3f357cf9f78259ae443a082b14a29535b.1343078495.git.tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We will need some of these values in mce.c. Move them to the
appropriate header file so they are available.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/0ccfb1af5fe35e537b7cd8e4d448bf7d851dbfb9.1343078495.git.tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When CONFIG_PERF_EVENTS disabled, there will have a compiliation
error, because missing struct before structure name.
Signed-off-by: Jovi Zhang <bookjovi@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jiri Kosina <trivial@kernel.org>
Link: http://lkml.kernel.org/r/CACV3sbKF%3DCX%2B2jWEWesfCA6rBoQ3wDM4-5ac9MuBtVbCtMRHdQ@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the current kernel, percpu variable `vector_irq' is not always
cleared when a CPU is offlined. If the CPU that has the disabled
irqs in vector_irq is hotplugged again, __setup_vector_irq()
hits invalid irq vector and may crash.
This bug can be reproduced as following;
# echo 0 > /sys/devices/system/cpu/cpu7/online
# modprobe -r some_driver_using_interrupts # vector_irq@cpu7 uncleared
# echo 1 > /sys/devices/system/cpu/cpu7/online # kernel may crash
To fix this problem, this patch clears vector_irq in
__fixup_irqs() when the CPU is offlined.
This also reverts commit f6175f5bfb, which partially fixes
this bug by clearing vector in __clear_irq_vector(). But in
environments with IOMMU IRQ remapper, it could fail because
cfg->domain doesn't contain offlined CPUs. With this patch, the
fix in __clear_irq_vector() can be reverted because every
vector_irq is already cleared in __fixup_irqs() on offlined CPUs.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama.qu@hitachi.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20120726104732.2889.19144.stgit@kvmdev
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The make target 'oldnoconfig' is a misnomer. It doesn't set new symbols
to 'n', but instead sets it to their default values.
Unfortunately, assuming that it actually did this, broke ktest in some
of its tests. For example, the tests to create a minimum config and even
a config bisect, depends on removing various configs and using
oldnoconfig to get rid of other configs that may have depended on it.
But because some configs that it was trying to disable, were in fact
default enabled, this caused those configs to re-enable and corrupt the
test.
I thought about fixing oldnoconfig, but I'm afraid that people are
already dependent on its current behavior. Instead, I'm just updating
the documentation to state that it sets the new symbols to their default
values and not to 'n'.
Ideally, this would be called, 'olddefconfig' and we have an
'oldnoconfig' that actually disables the new symbols. But it's useless
for me now. If it changed, ktest would need to be consistent between
each version, and that would be to difficult to detect. I'll handle this
issue with ktest with other means.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
As we use a macro trick to sync each error codes with its
description string, teach [ce]tags to process them properly.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-qt5fv4pzigr2nnl27ydimg4h@git.kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Thought to be another merge error, board-mop500-msp.h has never existed
in the upstream kernel, only msp.h. This patch changes the include files
to match the existing file name.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We believe to have squashed all issues around the gen6+ rps interrupt
generation and why the gpu sometimes got stuck. With that cleared up,
there's no user left for the sanitize_pm infrastructure, so let's just
rip it out.
Note that 'intel_reg_write 0xa014 0x13070000' is the w/a if we find
ourselves stuck again.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power docs say that when the gt leaves rc6, it is in the lowest
frequency and only about 25 usec later will switch to the frequency
selected in GEN6_RPNSWREQ. If the downclock limit expires in that
window and the down limit is set to the lowest possible frequency, the
hw will not send the down interrupt. Which leads to a too high gpu
clock and wasted power.
Chris Wilson already worked on this with
commit 7b9e0ae6da
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sat Apr 28 08:56:39 2012 +0100
drm/i915: Always update RPS interrupts thresholds along with
frequency
but got the logic inverted: The current code set the down limit as
long as we haven't reached it. Instead of only once with reached the
lowest frequency.
Note that we can't always set the downclock limit to 0, because
otherwise the hw will keep on bugging us with downclock request irqs
once the lowest level is reached.
For similar reasons also always set the upclock limit, otherwise the
hw might poke us again with interrupts.
v2: Chris Wilson noticed that the limit reg is also computed in
sanitize_pm. To avoid duplication, extract the code into a common
function.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a new trace system, kvm-s390, for some kvm/s390 specific
trace points:
- injection of interrupts
- delivery of interrupts to the guest
- creation/destruction of kvm machines and vcpus
- stop actions for vcpus
- reset requests for userspace
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add trace events for several s390 architecture specifics:
- SIE entry/exit
- common intercepts
- common instructions (sigp/diagnose)
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Provide a new function, insn_to_mnemonic, by which e.g. kvm can obtain
a human-readable decoding of an instruction's opcode.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
By selecting the cache level (essentially whether or not the CPU snoops
any updates to the bo, and on more recent machines whether it resides
inside the CPU's last-level-cache) a userspace driver is able to then
manage all of its memory within buffer objects, if it so desires. This
enables the userspace driver to accelerate uploads and more importantly
downloads from the GPU and to able to mix CPU and GPU rendering/activity
efficiently.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Added code comment about where we plan to stuff platform
specific cacheing control bits in the ioctl struct.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Several functions of the GPU have the restriction that differing memory
domains cannot be placed next to each other (as the GPU may prefetch
beyond the end of one domain and hang as it crosses into the other
domain). We use the facility of the drm_mm to mark ranges with a
particular color that corresponds to the cache attributes of those pages
in order to prevent allocating adjacent blocks of differing memory
types.
v2: Rebase ontop of drm_mm coloring v2.
v3: Fix rebinding existing gtt_space and add a verification routine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The event control register of SNB-EP uncore QPI box has a one bit
extension at bit position 21.
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1343097850-4348-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
LLC-* and node-* events require using the OFFCORE_RESPONSE events
on SandyBridge, but the hw_cache_extra_regs is left uninitialized.
This patch adds the missing extra register configure table for
SandyBridge.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1342517275-2875-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The uncore subsystem in Nehalem-EX consists of 7 components
(U-Box, C-Box, B-Box, S-Box, R-Box, M-Box and W-Box). This
patch is large because the way to program these boxes is
diverse.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4FF534F1.3030307@intel.com
[ Improved the code. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The format definition of uncore PCU filter should be filter_band*
instead of filter_brand*.
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1343024611-4692-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Otherwise they can't be filtered for a defined task:
perf record -e sched:sched_switch ./foo
This command doesn't report any events without this patch.
I think it isn't a security concern if someone knows who will
be executed next - this can already be observed by polling /proc
state. By default perf is disabled for non-root users in any case.
I need these events for profiling sleep times. sched_switch is used for
getting callchains and sched_stat_* is used for getting time periods.
These events are combined in user space, then it can be analyzed by
perf tools.
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arun Sharma <asharma@fb.com>
Link: http://lkml.kernel.org/r/1342088069-1005148-1-git-send-email-avagin@openvz.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
They function just like they do in less(1).
Also correct some discrepancy between the help text and the code wrt
function keys.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: Michal Marek <mmarek@suse.cz>
When reporting a string value, only the first double-quote was
un-escaped. We need to un-escape all escaped double-quotes.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Michal Marek <mmarek@suse.cz>
It seems there's no specific reason to open-code it. I guess
commit 0122ec5b02 ("sched: Add p->pi_lock to task_rq_lock()")
simply missed it. Let's be consistent with others.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1341647342-6742-1-git-send-email-namhyung@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 8e7fbcbc22 ("sched: Remove stale power aware scheduling remnants
and dysfunctional knobs") removed SD_PERFER_SIBLING from the CPU domain.
On NUMA machines this causes that load_balance() doesn't perfer LCPU in
same physical CPU package.
It causes some actual performance regressions on our NUMA machines from
Core2 to NHM and SNB.
Adding this domain flag again recovers the performance drop.
This change doesn't have any bad impact on any of my benchmarks:
specjbb, kbuild, fio, hackbench .. etc, on all my machines.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1342765190-21540-1-git-send-email-alex.shi@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Handle KVM_IRQ_LINE and KVM_IRQ_LINE_STATUS in the generic
kvm_vm_ioctl() function and call into kvm_vm_ioctl_irq_line().
This is even more relevant when KVM/ARM also uses this ioctl.
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
setup_syscalls_segments() calls get_segment() and than overwrites all
but one of the structure fields and this one should also be overwritten
anyway, so we can drop call to get_segment() and avoid a couple of vmreads
on vmx. Also drop zeroing ss/cs structures since most of the fields are
set anyway. Just set those that were not set explicitly.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
After commit 242ec97c35 PIT interrupts are no longer delivered after
PIC reset. It happens because PIT injects interrupt only if previous one
was acked, but since on PIC reset it is dropped from irr it will never
be delivered and hence acknowledged. Fix that by calling ack notifier on
PIC reset.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
No need split mmio read region into 8-bits pieces since we do it in
emulator_read_write_onepage
Changelog:
Add a WARN_ON to check read-cache overflow
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently, kvm allocates some pages and use them as error indicators,
it wastes memory and is not good for scalability
Base on Avi's suggestion, we use the error codes instead of these pages
to indicate the error conditions
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In kvm_async_pf_wakeup_all, it uses bad_page to generate broadcast wakeup,
and uses put_page to release bad_page, the work depends on the fact that
bad_page is the normal page. But we will use the error code instead of
bad_page, so use kvm_release_page_clean to release the page which will
release the error code properly
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>