The codec ALC272X is a special codec for some Dell machines, and its
detection got broken in the recent kernel because SSID check (required
by ALC272X check) was moved to the later point. Now we need to move
this codec check to the right place, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After 934b9d1e (wl18xx: avoid some -Wformat warnings) there was still
a warning with (at least) ARM gcc version 4.4.1:
drivers/net/wireless/ti/wl18xx/main.c: In function 'wl18xx_conf_init':
drivers/net/wireless/ti/wl18xx/main.c:1026: warning: format '%ld' expects type 'long int', but argument 2 has type 'unsigned int'
Fix this by using %zu for the both formats, since the fw->size and the
macro (derived from sizeof()) are size_t.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove the cap IEEE80211_HT_CAP_DSSSCCK40 from the 5Ghz variant of
the siso40 HT capabilities. It is meaningless in 5Ghz.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Introduce a default set of HT capabilities that are set according to the
number of antennas on the board. Move the HT setting code down to allow
the number of antennas to be set (and optionally overridden) before it.
Remove the "mimo" HT option, since the default mode now enables MIMO is
possible.
Use this opportunity to add a helper function for setting HT
capabilities and reduce the volume of the code a bit.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 18xx chip does not support MIMO in 5Ghz. Use the siso20 HT cap as
fallback in 5Ghz when "mimo" is requested.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
FW uses a few memory blocks as a buffer to accumulate FW logs before
transmitting them to the host over SDIO. When FW WatchDog recovery
occurs, the last FW traces are still pending in the buffer. Driver is
to read these FW traces whether log mode is continuous or on demand.
FW memory blocks allocated for the log buffer are handled as a link list:
the first 4 bytes in each memory block contain FW address to the next block.
The end of list condition depends on FW log mode:
- on demand: the list is cyclic, the next address is equal to the first address
- continuous: the address is equal to 0x2000000
Log data resides inside FW memory block with offset depending on
logger mode:
- on demand: 4 bytes (address of the next memory block)
- continuous: 4 bytes and Rx Descriptor structure size
Described FW logger API is backward compatible with previous FW versions.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The get survey op expects the low level driver to report
the noise level for a a given channel.
The noise calculated in wlcore is (rssi-snr/2), but since
the snr reported by the FW is a derivative from the rssi
this calculation is useless, and should not be reported
to the user space.
Reporting incorrect noise, results in the wpa_supplicant
miscalculating the roaming candidate priority, thus causing
a situation where an AP with a lower rssi level would be
chosen over a better AP.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Before patch b5d6d9b (wlcore/wl12xx/wl18xx: don't use TX align quirk
for wl127x), this was automatically set for all platforms. As this
should now be set explicitly, set it for PG2 as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New PG2 firmwares have additional Rx descriptors.
Add a module parameter to manually set the number of Rx descriptors for
older versions (PG1). We cannot discriminate based on chip-id, since
this value must be set on probe.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
drivers/media/video/pms.c uses kzalloc() and kfree() so it should
include <linux/slab.h> to fix build errors and a warning.
drivers/media/video/pms.c:1047:2: error: implicit declaration of function 'kzalloc'
drivers/media/video/pms.c:1047:6: warning: assignment makes pointer from integer without a cast
drivers/media/video/pms.c:1116:2: error: implicit declaration of function 'kfree'
Found in mmotm but applies to mainline.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is some concern that these iput()'s could be the final iputs and could
induce lockups on people waiting on writeback. This would happen in the
rare case that we don't create ordered extents because of an error, but it
is theoretically possible and we already have a mechanism to deal with this
so just make them delayed iputs to negate any worry.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
When fixing up the locking in the delayed ref destruction work I accidently
broke the locking myself ;(. Add back a spin_lock that should be there and
we are now all set. Thanks,
Btrfs: add a missing spin_lock
When fixing up the locking in the delayed ref destruction work I accidently
broke the locking myself ;(. Add back a spin_lock that should be there and
we are now all set. Thanks,
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
add_all_parents did assume that path is already at a correct extent data
item, which may not be true in case of data extents that were partly
rewritten and splitted.
We need to check if we're on a matching extent for every item and only
for the ones after the first. The loop is changed to do this now.
This patch also fixes a bug introduced with commit 3b127fd8 "Btrfs:
remove obsolete btrfs_next_leaf call from __resolve_indirect_ref".
The removal of next_leaf did sometimes result in slot==nritems when
the above described case happens, and thus resulting in invalid values
(e.g. wanted_obejctid) in add_all_parents (leading to missed backrefs
or even crashes).
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
We introduce btrfs_next_old_item that uses btrfs_next_old_leaf instead
of btrfs_next_leaf.
btrfs_next_item is also changed to simply call btrfs_next_old_item with
time_seq being 0.
Signed-off-by: Alexander Block <ablock84@googlemail.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
* 'next' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: replace cs_mutex with vm_mutex v3
drm/radeon: replace pflip and sw_int counters with atomics
drm/radeon: apply Murphy's law to the kms irq code v3
drm/radeon: fix & improve ih ring handling v3
drm/radeon: remove some unneeded structure members
drm/radeon: replace vmram_mutex with mclk_lock v2
drm/radeon: rework ring syncing code
drm/radeon: add infrastructure for advanced ring synchronization v2
drm/radeon: remove radeon_fence_create
Use err log rather than warning message when the platform data is NULL
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
KZM-A9-GT board has RTC device r2025d at I2C channel 0
with slave address 0x64.
This patch enables reading and writing hardware real time clock on
KZM-A9-GT board. Interrupt is not yet supported.
How to test this patch using user space command.
Read RTC
# hwclock -r
Copy system clock to RTC
# hwclock -w
Shutdown and power off the board, and wait a while, then power on again.
Check RTC still keeps correct date.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch enable camera support on CON1
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The sleep_auth value of the last interface to be set up prevailed when
an interface was removed. Take care of this by correctly configuring the
value according to the remaining STA/AP interfaces.
Take this opportunity to refactor the sleep_auth setting code for better
readability.
[Small style fix. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.
This makes debugging more intuitive using the debugfs value.
Increment the conf version since we added an element to the conf
structure.
Note: An AP going up will always set sleep_auth to PSM_CAM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For FW debugging purposes, we may need to change the sleep mode
(aka. sleep_auth) by hand, and set it to the mode we want. To allow
this, a debugfs entry is added.
Now we store the sleep_auth value that has been set and use that
instead of the quirk to decide whether we should enter ELP or not.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The ampdu_action() function is called on the reconfig() path to remove
existing Rx BA sessions. Since these don't exist for the low level
driver, we output an error message. Turn the message into a debug
message for now, until the mac80211 reconfig flow is changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In the recent code, the value shown there is a tag number, and it's no
longer same as the pin nid. Correct the message to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA codecs seem not returning the event tag in the unsolicited events,
thus the current code relying on the tag value doesn't work.
Since simple_hdmi stuff has only a single pin, we can use simply
snd_hda_jack_set_dirty_all() to activate the pin-detection
independently from the tag value.
Tested-by: Annie Liu <AnnieLiu@viatech.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kconfig doesn't do the right thing for us here.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 21cc1b7ede ("ARM: shmobile:
use machine specific hook for late init") suspend and CPU idle are not
initialized automatically anymore. Set shmobile_init_late() as the
machine late init hook to initialize them.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since commit 21cc1b7ede ("ARM: shmobile:
use machine specific hook for late init") suspend and CPU idle are not
initialized automatically anymore. Set shmobile_init_late() as the
machine late init hook to initialize them.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Since commit 21cc1b7ede ("ARM: shmobile:
use machine specific hook for late init") suspend and CPU idle are not
initialized automatically anymore. Set shmobile_init_late() as the
machine late init hook to initialize them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Just the OMAP part here, the rest goes via other patches and trees.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The beagleboard USB Host Port that is used is Port 2. The platform driver
sets MODE_PHY for port 1 causing pin muxing to override the pins on the
expansion connector P17 when using board_mux[]. Since USBHS Port 1 is not
connected remove the case for muxing the USB Port1 pins by default.
Tested with BeagleBoard xM revC and checked the userguides for Beagle xM
and revC to be sure USB Port2 is what is used.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the kernel is built only for OMAP2 the following warning will show up:
arch/arm/mach-omap2/twl-common.c:52: warning: ‘twl_set_voltage’ defined but not used
arch/arm/mach-omap2/twl-common.c:58: warning: ‘twl_get_voltage’ defined but not used
The twl_set/get_voltage callbacks only used when OMAP3/4 is selected.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case a board provides the gpio_pendown and not board_pdata,
the GPIO debounce is not taken care of.
Fix this by taking care of GPIO debounce in any case.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is more readable by printing "ret = -1" than "ret = 0xffffffff"
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to initialize this to false, because the is_rb callback only
ever sets it to true.
Noticed while reading through the code.
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes the following sparse warning:
drivers/gpu/drm/drm_info.c:238:5:
warning: symbol 'drm_gem_one_name_info' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently when mac80211 asks to change the interface
type, we will accept it for both the BSS and PAN
contexts. This is not terribly complicated today,
but with the addition of the P2P Device abstraction
the PAN context handling will get more complex, so
restrict mac_change_interface to the BSS context.
Also fix a small locking issue and use is_active
instead of the vif pointer to check if the other
context is activated, guarding exclusive interface
types on the BSS context (IBSS) against the PAN
context being used for something else.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the first interface is active, then scanning
on it or the second interface can take a little
longer than 7s (I observed around 8s.) Bump the
timeout to 15s to avoid aborting a scan that is
still running, just taking more time.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My previous commit to shorten the radio reset time
caused issues as the firmware checks the active
dwell time against the quiet time, asserting that
the dwell is >= quiet time. This isn't really
needed in case of passive scanning like here, but
of course we need to pass that check.
To fix this, override the quiet time to be the
same as the radio reset dwell time.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to remove or replace the cs_mutex with a
vm_mutex where it is still needed.
v2: fix locking order
v3: rebased on drm-next
Signed-off-by: Christian König <deathsimple@vodafone.de>
So we can skip the locking. Also renames sw_int to
ring_int, cause that better matches its purpose.
Signed-off-by: Christian Koenig <christian.koenig@amd.com>
1. It is really dangerous to have more than one
spinlock protecting the same information.
2. radeon_irq_set sometimes wasn't called with lock
protection, so it can happen that more than one
CPU would tamper with the irq regs at the same
time.
3. The pm.gui_idle variable was assuming that the 3D
engine wasn't becoming idle between testing the
register and setting the variable. So just remove
it and test the register directly.
v2: Also handle the hpd irq code the same way.
v3: Rename hpd parameter for clarification.
Signed-off-by: Christian Koenig <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The spinlock was actually there to protect the
rptr, but rptr was read outside of the locked area.
Also we don't really need a spinlock here, an
atomic should to quite fine since we only need to
prevent it from being reentrant.
v2: Keep the spinlock....
v3: Back to an atomic again after finding & fixing the real bug.
Signed-off-by: Christian Koenig <christian.koenig@amd.com>
It is a rw_semaphore now and only write locked
while changing the clock. Also the lock is renamed
to better reflect what it is protecting.
v2: Keep the ttm_vm_ops on IGPs
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Move inter ring syncing with semaphores into the
existing ring allocations, with that we need to
lock the ring mutex only once.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>