Problem Observed:
- interrupt status is set by rising or falling edge on CTS line
- interrupt status is cleared on a .0. to .1. transition of the
interrupt-clear register bit 1.
- interrupt-clear register is reset by hardware once the interrupt
status is .0..
Remark: It seems not possible to read this register back by the
CPU though, but internally this register exists.
- when simultaneous set and reset event on the interrupt status
happens, then the set-event has priority and the status remains
.1.. As a result the interrupt-clear register is not reset to
.0., and no new .0. to .1. transition can be detected on it when
writing a .1. to it.
This implies race condition, the clear must be performed at least
one UARTCLK the riding edge of CTS RIS interrupt.
Fix:
Instead of resetting UART as done in commit
c16d51a32b
"amba pl011: workaround for uart registers lockup" do the
following:
write .0. and then .1. to the interrupt-clear register to make
sure that this transition is detected. According to the datasheet
writing a .0. does not have any effect, but actually it allows to
reset the internal interrupt-clear register.
Take into account:
The .0. needs to last at least for one clk_uart clock period
(~ 38 MHz, 26.08ns)
This way we can do away with the tasklet and keep only a tiny
fix triggered by the variant flag introduced in this patch.
Signed-off-by: Guillaume Jaunet <guillaume.jaunet@stericsson.com>
Signed-off-by: Christophe Arnal <christophe.arnal@stericsson.com>
Signed-off-by: Matthias Locher <Matthias.Locher@stericsson.com>
Signed-off-by: Rajanikanth H.V <rajanikanth.hv@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updated the generic SPI EEPROM driver AT25 for support of an additional address
bit in the instruction byte. Certain EEPROMS have a size that is larger than the
number of address bytes would allow (e.g. like M95040 from ST that has 512 Byte
size but uses only one address byte (A0 to A7) for addressing.) For the extra
address bit (A8, A16 or A24) bit 3 of the instruction byte is used. This
instruction bit is normally defined as don't care for other AT25 like chips.
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bmp18x chip family comes in an I2C respectively SPI variant.
Hence, the bmp085 driver was split to support both buses.
Tested-by: Zhengguang Guo <zhengguang.guo@bosch-sensortec.com>
Reviewed-by: Stefan Nilsson <stefan.nilsson@unixphere.com>
Signed-off-by: Eric Andersson <eric.andersson@unixphere.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes various cleaning of the bmp085 driver including:
- Whitespaces and alignment fixes
- Minor typos
- Consistency fixes
Reviewed-by: Stefan Nilsson <stefan.nilsson@unixphere.com>
Signed-off-by: Eric Andersson <eric.andersson@unixphere.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No symbol can be exported when the section is discarded - the only
solution I could think of is not to mark symbols as __devexit
when they are exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers that refer to a __devexit function in an operations
structure need to annotate that pointer with __devexit_p so it
is replaced with a NULL pointer when the section gets discarded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code does not properly free allocated irqs if request_threaded_irq
returns error, fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
these drivers are used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for them.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This call is not needed; the IRQ controller should (and does) set up
interrupts correctly. set_irq_flags() isn't exported to modules, to
this also fixes compilation of ehci-tegra.c as a module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the two previously allocated buffers before exiting the function in an
error case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed the assignment statements found in if statements by the
checkpatch.pl tool.
Signed-off-by: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1541) corrects a small mistake in ehci-hcd. The IAAD
(Interrupt on Async Advance Doorbell) bit in the USBCMD register is
designed, as its name says, to act as a "doorbell". That is, the
driver activates the bit by setting it to 1, and the hardware
deactivates it later by setting it back to 0. The driver cannot clear
the bit by writing a 0 to it; such writes are simply ignored.
Therefore there is no reason for ehci-hcd to try to clear the bit.
The patch removes the two instances where such attempts occur.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to configure the SPEAr EHCI & OHCI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Beregalov reported skb_over_panic errors and provided stack
trace.
I occurs commit a21d45726a (tcp: avoid order-1 allocations on wifi and
tx path) added a regression, when a retransmit is done after a partial
ACK.
tcp_retransmit_skb() tries to aggregate several frames if the first one
has enough available room to hold the following ones payload. This is
controlled by /proc/sys/net/ipv4/tcp_retrans_collapse tunable (default :
enabled)
Problem is we must make sure _pskb_trim_head() doesnt fool
skb_availroom() when pulling some bytes from skb (this pull is done when
receiver ACK part of the frame).
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Marc MERLIN <marc@merlins.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds clock gating to suspend and resume functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In devices using ehci-sh, initialization of the PHY may be necessary.
This adds platform data to ehci-sh and provide function to initialize PHY.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Shimoda, Yoshihiro <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
release_firmware() tests for a NULL pointer, so it's redundant to do
that checking before calling it.
Additionally, in ene_load_bincode(), 'sd_fw' is a local variable so
setting it to NULL just before it goes out of scope is completely
pointless, so remove that assignment.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-arranged EHCI generic and tegra specific functions
into two separate groups for more readability.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After packetize_urb was called, we could still run into an error path
and will not hand over the prepared qtd to the qtd_list. Make sure to
free the prepared qtd in that case to avoid memory leaks.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that dequeued urbs get handled first
by collect_qtds. To achieve that we better move them
up to the head in the qh list.
This for instance fixes hanging serial devices, which wait
for dequeued urbs to properly close their device node.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DEBUG is defined, the kmem_cache_create call a
WARN_ON if the name of the cache uses a space.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch, the prepared disable routines
will not be called on module unloading.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the change to start adjusting the sync polarity of the LVDS mode
was introduced in
commit aa9b500ddf
Author: Bryan Freed <bfreed@google.com>
Date: Wed Jan 12 13:43:19 2011 -0800
drm/i915: Honour LVDS sync polarity from EDID
we made the change in state verbose so that we could quickly spot any
regressions that made have also been introduced with it. As there do not
appear to have been any, remove the extra logging.
v2: Remove the no longer used variables.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for ULPI and UTMI PHYs based on usb controller
version info read from device-tree
Example of USB Controller versioning info:
Version 1.2 and below : MPC8536, MPC8315, etc
Version 1.6 : P1020, P1010, P2020, P5020, etc
Version 2.2 : PSC9131, PSC9132, P3060, etc
No changes for non-DT users
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow drivers to return EOPNOTSUPP to user space even when filtered
through usb_translate_errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It displays wrong debug message if we plug in a full/low
speed device at port for builtin TT controller. We can get
device/port speed information at following code of hub_port_init,
so it is better to replace it with debug message of "reset complete".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch:
1. Renamed structure and function names to be more meaningful.
2. Removed unnecessary local variables.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now replaced by the new ssb USB driver, which also supports
devices with an EHCI controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom ssb bus. The ssb bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the ssb bus at the same time.
The old ssb OHCI USB driver will be removed in the next step as this
driver also provide an OHCI driver and an EHCI for the cores supporting
it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom bcma bus. The bcma bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the bcma bus at the same time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some cores like the USB core have two address spaces. In the USB host
controller one address space is used for the OHCI and the other for the
EHCI controller interface. The USB controller is the only core I found
with two address spaces. This code is based on the AI scan function
ai_scan() in shared/aiutils.c in the Broadcom SDK.
CC: Rafał Miłecki <zajec5@gmail.com>
CC: linux-wireless@vger.kernel.org
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Only provide debugfs-relates ops when CONFIG_DEBUG_FS is enabled.
* Implement pin_config_group_dbg_show op.
* Implement pin_config_config_dbg_show op.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Pull security subsystem fixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
fcaps: clear the same personality flags as suid when fcaps are used
mpi: Avoid using freed pointer in mpi_lshift_limbs()
Smack: move label list initialization
spi_board_info is not modified in any of the spi registeration
functions and passed along as-is to the generic SPI layer.
Mark spi_board_info arguments as const to signal this.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[nsekhar@ti.com: extended for dm365 and dm355]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fatal errors such as a device disconnect must not trigger
error handling. The error returns must be checked.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
del_timer_sync() cannot be used in interrupt.
Replace it with del_timer() and a flag
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds intel_pm routine for generic power-related infrastructure
initialization.
v2: now that all the platform-specific stuff is initialized in one place, we
can also add back the static definitions to platform-specific functions which
we abstract now.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BCJ filters were meant to be enabled already on these
archs, but the xz_wrap.sh script was buggy. Enabling the
filters should give smaller kernel images.
xz_wrap.sh will now use $SRCARCH instead of $ARCH to detect
the architecture. That way it doesn't need to care about the
subarchs (like i386 vs. x86_64) since the BCJ filters don't
care either.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Acked-by: Jan Beulich <jbeulich@suse.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PDCTL NEXT bit is incorrectly set to bit 1 instead of bit 0. This
patch fixes this issue
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This moves the clock gating-related functions into intel_pm module.
Also, please note that we do change the function type from static to
non-static in this patch for the move, to prevent breaking bisecting with
non-working intermediate commit. Those are returned back to static form in
the following patch which setups a generic PM initialization function,
which was split into a different one to simplify review.
v2: rebase on top of latest drm-intel-next-queued to incorporate all the
changes that went there meanwhile.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.
Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the Ironlake energy monitoring functionality into intel_pm
module.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
default, due to issues with suspend/resume and hotplug.
To re-enable, use sysfs.
2) make ata_print_id atomic, due to ref from multiple contexts
3) sata_mv warning fix
4) ata_piix new PCI ID
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Ku0x
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libara fixes from Jeff Garzik:
- Notable regression fix. Forbid dynamic runtime power management by
default, due to issues with suspend/resume and hotplug.
To re-enable, use sysfs.
- make ata_print_id atomic, due to ref from multiple contexts
- sata_mv warning fix
- ata_piix new PCI ID
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: forbid port runtime pm by default, fixing regression
libata: make ata_print_id atomic
sata_mv: silence an uninitialized variable warning
ata_piix: IDE-mode SATA patch for Intel DH89xxCC DeviceIDs