Add support for DH electronics i.MX8MP DHCOM SoM on DRC02 carrier board.
This system is populated with two ethernet ports, two CANs, RS485 and RS232,
USB, capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Document support for DH electronics i.MX8MP DHCOM SoM on DRC02 carrier board.
This system is populated with two ethernet ports, two CANs, RS485 and RS232,
USB, capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix typo in airoha_fe_init routine configuring CDM2_OAM_QSEL_MASK field
of REG_CDM2_FWD_CFG register.
This bug is not introducing any user visible problem since Frame Engine
CDM2 port is used just by the second QDMA block and we currently enable
just QDMA1 block connected to the MT7530 dsa switch via CDM1 port.
Introduced by commit 23020f0493 ("net: airoha: Introduce ethernet
support for EN7581 SoC")
Reported-by: ChihWei Cheng <chihwei.cheng@airoha.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241015-airoha-eth-cdm2-fixes-v1-1-9dc6993286c3@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The GbEth IP supports offloading checksum calculation for VLAN-tagged
packets, provided that the EtherType is 0x8100 and only one VLAN tag is
present.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The GbEth IP supports offloading IPv6 TCP, UDP & ICMPv6 checksums in the
TX path.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The GbEth IP supports offloading IPv6 TCP, UDP & ICMPv6 checksums in the
RX path.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The GbEth IP will pass through a zero UDP checksum without asserting any
error flags so we do not need to resort to software checksum calculation
in this case.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
For IPv4 packets, the header checksum will always be calculated in software
in the TX path (Documentation/networking/checksum-offloads.rst says "No
offloading of the IP header checksum is performed; it is always done in
software.") so there is no advantage in asking the hardware to also
calculate this checksum.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The hardware checksum value is used as a 16-bit flag, it is zero when
the checksum has been validated and non-zero otherwise. Therefore we
don't need to treat this as an actual __wsum type or call csum_unfold(),
we can just use a u16 pointer.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
We can merge the two if conditions on skb_is_nonlinear(). Since
skb_frag_size_sub() and skb_trim() do not free memory, it is still safe
to access the trimmed bytes at the end of the packet after these calls.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
We do not need to confirm that the protocol is IPv4. If the hardware
encounters an unsupported protocol, it will set the checksum value to
0xFFFF.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
For IPv4 packets, the header checksum will always be checked in software
in the RX path (inet_gro_receive() calls ip_fast_csum() unconditionally)
so there is no advantage in asking the hardware to also calculate this
checksum.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Introduce new constants for the CSR1 (TX) and CSR2 (RX) checksum enable
bits, removing the risk of inconsistency when we change which flags we
enable.
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
GCC is not happy with the current code, e.g.:
.../tg3.c:11313:37: error: ‘-txrx-’ directive output may be truncated writing 6 bytes into a region of size between 1 and 16 [-Werror=format-truncation=]
11313 | "%s-txrx-%d", tp->dev->name, irq_num);
| ^~~~~~
.../tg3.c:11313:34: note: using the range [-2147483648, 2147483647] for directive argument
11313 | "%s-txrx-%d", tp->dev->name, irq_num);
When `make W=1` is supplied, this prevents kernel building. Fix it by
increasing the buffer size for IRQ label and use sizeoF() instead of
hard coded constants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Message-ID: <20241016090647.691022-1-andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
as part of IBPB. Make sure that happens by doing the flushing in
software on those generations
-----BEGIN PGP SIGNATURE-----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=ovJa
-----END PGP SIGNATURE-----
Merge tag 'x86_bugs_post_ibpb' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 IBPB fixes from Borislav Petkov:
"This fixes the IBPB implementation of older AMDs (< gen4) that do not
flush the RSB (Return Address Stack) so you can still do some leaking
when using a "=ibpb" mitigation for Retbleed or SRSO. Fix it by doing
the flushing in software on those generations.
IBPB is not the default setting so this is not likely to affect
anybody in practice"
* tag 'x86_bugs_post_ibpb' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Do not use UNTRAIN_RET with IBPB on entry
x86/bugs: Skip RSB fill at VMEXIT
x86/entry: Have entry_ibpb() invalidate return predictions
x86/cpufeatures: Add a IBPB_NO_RET BUG flag
x86/cpufeatures: Define X86_FEATURE_AMD_IBPB_RET
The barrier_nospec() after the array bounds check is overkill and
painfully slow for arches which implement it.
Furthermore, most arches don't implement it, so they remain exposed to
Spectre v1 (which can affect pretty much any CPU with branch
prediction).
Instead, clamp the user pointer to a valid range so it's guaranteed to
be a valid array index even when the bounds check mispredicts.
Fixes: 8270cb10c0 ("cdrom: Fix spectre-v1 gadget")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/1d86f4d9d8fba68e5ca64cdeac2451b95a8bf872.1729202937.git.jpoimboe@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
drm-misc-next for v6.13:
Cross-subsystem Changes:
- Small fixes to dma-buf.
Core Changes:
- Convert many drivers to use video aperture helpers and remove the DRM
one.
Driver Changes:
- Add coredump, pantherlake support to accel/ivpu.
- Assorted bugfixes to ivpu, edp-panel, bochs, gcc-15, panel/s6e3ha8.
- Docbook fixes for TTM.
- Add Samsung AMS581VF01
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b9f475d2-d6e0-4f88-b533-1c674a293022@linux.intel.com
It is the usual shower of unrelated singletons - please see the individual
changelogs for details.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZxGY5wAKCRDdBJ7gKXxA
js6RAQC16zQ7WRV091i79cEi1C5648NbZjMCU626hZjuyfbzKgEA2v8PYtjj9w2e
UGLxMY+PYZki2XNEh75Sikdkiyl9Vgg=
=xcWT
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2024-10-17-16-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"28 hotfixes. 13 are cc:stable. 23 are MM.
It is the usual shower of unrelated singletons - please see the
individual changelogs for details"
* tag 'mm-hotfixes-stable-2024-10-17-16-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (28 commits)
maple_tree: add regression test for spanning store bug
maple_tree: correct tree corruption on spanning store
mm/mglru: only clear kswapd_failures if reclaimable
mm/swapfile: skip HugeTLB pages for unuse_vma
selftests: mm: fix the incorrect usage() info of khugepaged
MAINTAINERS: add Jann as memory mapping/VMA reviewer
mm: swap: prevent possible data-race in __try_to_reclaim_swap
mm: khugepaged: fix the incorrect statistics when collapsing large file folios
MAINTAINERS: kasan, kcov: add bugzilla links
mm: don't install PMD mappings when THPs are disabled by the hw/process/vma
mm: huge_memory: add vma_thp_disabled() and thp_disabled_by_hw()
Docs/damon/maintainer-profile: update deprecated awslabs GitHub URLs
Docs/damon/maintainer-profile: add missing '_' suffixes for external web links
maple_tree: check for MA_STATE_BULK on setting wr_rebalance
mm: khugepaged: fix the arguments order in khugepaged_collapse_file trace point
mm/damon/tests/sysfs-kunit.h: fix memory leak in damon_sysfs_test_add_targets()
mm: remove unused stub for can_swapin_thp()
mailmap: add an entry for Andy Chiu
MAINTAINERS: add memory mapping/VMA co-maintainers
fs/proc: fix build with GCC 15 due to -Werror=unterminated-string-initialization
...
- Terminate the of_device_id table in the Samsung exynosautov920 clk
driver so that device matching logic doesn't run off the end of the
array into other memory and break matching for any kernel with this
driver loaded
- Properly limit the max clk ID in the Rockchip clk driver
- Use clk kunit helpers in the clk tests so that memory isn't leaked
after the test concludes
-----BEGIN PGP SIGNATURE-----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=EKY/
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two clk driver fixes and a unit test fix:
- Terminate the of_device_id table in the Samsung exynosautov920 clk
driver so that device matching logic doesn't run off the end of the
array into other memory and break matching for any kernel with this
driver loaded
- Properly limit the max clk ID in the Rockchip clk driver
- Use clk kunit helpers in the clk tests so that memory isn't leaked
after the test concludes"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: test: Fix some memory leaks
clk: rockchip: fix finding of maximum clock ID
clk: samsung: Fix out-of-bound access of of_match_node()
With DSA's implementation of the mac_select_pcs() method removed, we
can now remove the detection of mac_select_pcs() implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
When the mac_select_pcs() method is not implemented, there is no way
for pl->pcs to be set to a non-NULL value. This was here to support
the old phylink_set_pcs() method which has been removed a few years
ago. Simplify the code in phylink_validate_mac_and_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
phylink has historically not permitted a PCS to be removed. An attempt
to permit this with phylink_set_pcs() resulted in comments indicating
that there was no need for this. This behaviour has been propagated
forward to the mac_select_pcs() approach as it was believed from these
comments that changing this would be NAK'd.
However, with mac_select_pcs(), it takes more code and thus complexity
to maintain this behaviour, which can - and in this case has - resulted
in a bug. If mac_select_pcs() returns NULL for a particular interface
type, but there is already a PCS in-use, then we skip the pcs_validate()
method, but continue using the old PCS. Also, it wouldn't be expected
behaviour by implementers of mac_select_pcs().
Allow this by removing this old unnecessary restriction.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Rather than returning an EOPNOTSUPP error pointer when the switch
has no support for PCS, return NULL to indicate that no PCS is
required.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
There is no longer any reason to implement the mac_select_pcs()
callback in DSA. Returning ERR_PTR(-EOPNOTSUPP) is functionally
equivalent to not providing the function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Use %*ph format to print small buffer as hex string. It will change
the output format from 32-bit words to byte hexdump, but this is not
critical as it's only a debug message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016132615.899037-1-andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
In sr_mdio_read() the local variable res is used to store both
little-endian and host byte order values. This prevents Sparse
from helping us by flagging when endian miss matches occur - the
detection process hinges on the type of variables matching the
byte order of values stored in them.
Address this by adding a new local variable, word, to store little-endian
values; change the type of res to int, and use it to store host-byte
order values.
Flagged by Sparse as:
.../sr9700.c:205:21: warning: incorrect type in assignment (different base types)
.../sr9700.c:205:21: expected restricted __le16 [addressable] [usertype] res
.../sr9700.c:205:21: got int
.../sr9700.c:207:21: warning: incorrect type in assignment (different base types)
.../sr9700.c:207:21: expected restricted __le16 [addressable] [usertype] res
.../sr9700.c:207:21: got int
.../sr9700.c:212:16: warning: incorrect type in return expression (different base types)
.../sr9700.c:212:16: expected int
.../sr9700.c:212:16: got restricted __le16 [addressable] [usertype] res
Compile tested only.
No functional change intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Message-ID: <20241016-blackbird-le16-v1-1-97ba8de6b38f@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The *ndev pointer needs to be set or it leads to an uninitialized variable
bug in the caller.
Fixes: 4a7b2ba94a ("net: ethernet: ti: am65-cpsw: Use tstats instead of open coded version")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Message-ID: <b168d5c7-704b-4452-84f9-1c1762b1f4ce@stanley.mountain>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Same as MT8195, MT8188 GPU clock is primarly supplied by the dedicated
mfgpll. The clock "mfg_core_tmp" is only used as an alt clock when
setting mfgpll clock rate.
If we keep the univpll parents from mfg_core_tmp, when setting
GPU frequency to 390000000, the common clock framework would switch
the parent to univpll, instead of setting mfgpll to 390000000:
mfgpll 0 0 0 949999756
univpll 2 2 0 2340000000
univpll_d6 1 1 0 390000000
top_mfg_core_tmp 1 1 0 390000000
mfg_ck_fast_ref 1 1 0 390000000
mfgcfg_bg3d 1 1 0 390000000
This results in failures when subsequent devfreq operations need to
switch to other frequencies. So remove univpll from the parent list.
This solution is taken from commit 72d38ed720 ("clk: mediatek:
clk-mt8195-topckgen: Drop univplls from mfg mux parents")
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240927103005.17605-3-pablo.sun@mediatek.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add auxiliary driver to support Nuvoton Arbel BMC NPCM8XX contains an
integrated clock controller which generates and supplies clocks to all
modules within the BMC.
The NPCM8xx clock controller is created using the auxiliary device
framework and set up in the npcm reset driver since the NPCM8xx clock is
using the same register region.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Tested-by: Benjamin Fair <benjaminfair@google.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20240912191038.981105-4-tmaimon77@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add NPCM8xx clock controller auxiliary bus device registration.
The NPCM8xx clock controller is registered as an aux device because the
reset and the clock controller share the same register region.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Tested-by: Benjamin Fair <benjaminfair@google.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240912191038.981105-3-tmaimon77@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This commit adds a 25MHz reference clock and clock-cell properties to
the NPCM reset document. The addition is necessitated by the integration
of the NPCM8xx clock auxiliary bus device into the NPCM reset driver.
The inclusion of the NPCM8xx clock properties in the reset document is
crucial as the reset block also serves as a clock provider for the
NPCM8xx clock. This enhancement is intended to facilitate the use of the
NPCM8xx clock driver.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240912191038.981105-2-tmaimon77@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This reverts commit c02904f05f.
Such commit assumed that only two symbols are relevant for the symbol
size calculation. However, this can lead to an incorrect symbol size
calculation when there are mapping symbols emitted by readelf.
For instance, when feeding 'update_irq_load_avg+0x1c/0x1c4', faddr2line
might need to process the following readelf lines:
784284: ffffffc0081cca30 428 FUNC GLOBAL DEFAULT 2 update_irq_load_avg
87319: ffffffc0081ccb0c 0 NOTYPE LOCAL DEFAULT 2 $x.62522
87321: ffffffc0081ccbdc 0 NOTYPE LOCAL DEFAULT 2 $x.62524
87323: ffffffc0081ccbe0 0 NOTYPE LOCAL DEFAULT 2 $x.62526
87325: ffffffc0081ccbe4 0 NOTYPE LOCAL DEFAULT 2 $x.62528
87327: ffffffc0081ccbe8 0 NOTYPE LOCAL DEFAULT 2 $x.62530
87329: ffffffc0081ccbec 0 NOTYPE LOCAL DEFAULT 2 $x.62532
87331: ffffffc0081ccbf0 0 NOTYPE LOCAL DEFAULT 2 $x.62534
87332: ffffffc0081ccbf4 0 NOTYPE LOCAL DEFAULT 2 $x.62535
783403: ffffffc0081ccbf4 424 FUNC GLOBAL DEFAULT 2 sched_pelt_multiplier
The symbol size of 'update_irq_load_avg' should be calculated with the
address of 'sched_pelt_multiplier', after skipping the mapping symbols
seen in between. However, the offending commit cuts the list short and
faddr2line incorrectly assumes 'update_irq_load_avg' is the last symbol
in the section, resulting in:
$ scripts/faddr2line vmlinux update_irq_load_avg+0x1c/0x1c4
skipping update_irq_load_avg address at 0xffffffc0081cca4c due to size mismatch (0x1c4 != 0x3ff9a59988)
no match for update_irq_load_avg+0x1c/0x1c4
After reverting the commit the issue is resolved:
$ scripts/faddr2line vmlinux update_irq_load_avg+0x1c/0x1c4
update_irq_load_avg+0x1c/0x1c4:
cpu_of at kernel/sched/sched.h:1109
(inlined by) update_irq_load_avg at kernel/sched/pelt.c:481
Fixes: c02904f05f ("scripts/faddr2line: Check only two symbols when calculating symbol size")
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
When arch_stack_walk_reliable() is called to unwind for newly forked
tasks, the return value is negative which means the call stack is
unreliable. This obviously does not meet expectations.
The root cause is that after commit 3aec4ecb3d ("x86: Rewrite
ret_from_fork() in C"), the 'ret_addr' of newly forked task is changed
to 'ret_from_fork_asm' (see copy_thread()), then at the start of the
unwind, it is incorrectly interprets not as a "signal" one because
'ret_from_fork' is still used to determine the initial "signal" (see
__unwind_start()). Then the address gets incorrectly decremented in the
call to orc_find() (see unwind_next_frame()) and resulting in the
incorrect ORC data.
To fix it, check 'ret_from_fork_asm' rather than 'ret_from_fork' in
__unwind_start().
Fixes: 3aec4ecb3d ("x86: Rewrite ret_from_fork() in C")
Signed-off-by: Zheng Yejian <zhengyejian@huaweicloud.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
When building objtool against a sysroot that contains a stripped down
version of the UAPI headers, the following error happens:
In file included from arch/x86/decode.c:10:
In file included from .../tools/arch/x86/include/asm/insn.h:10:
In file included from <sysroot>/include/asm/byteorder.h:9:
In file included from <sysroot>/include/linux/byteorder/little_endian.h:15:
In file included from <sysroot>/include/linux/stddef.h:9:
In file included from .../tools/include/linux/compiler_types.h:36:
.../tools/include/linux/compiler-gcc.h:3:2: error: "Please don't include <linux/compiler-gcc.h> directly, include <linux/compiler.h> instead."
3 | #error "Please don't include <linux/compiler-gcc.h> directly, include <linux/compiler.h> instead."
| ^
1 error generated.
As hinted by the error, this is because <sysroot>/include/linux/stddef.h
(a stripped-down version of uapi/include/linux/stddef.h) includes
linux/compiler_types.h directly. However, this gets resolved to
tools/include/linux/compiler_types.h, which is not expected to be
included directly.
To resolve this, I added tools/include/uapi to the include paths when
building objtool. With this trick, linux/stddef.h is resolved to
tools/include/uapi/linux/stddef.h, which doesn't include
linux/compiler_types.h.
Signed-off-by: HONG Yifan <elsk@google.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
When kernel IBT is enabled, objtool detects all text references in order
to determine which functions can be indirectly branched to.
In text, such references look like one of the following:
mov $0x0,%rax R_X86_64_32S .init.text+0x7e0a0
lea 0x0(%rip),%rax R_X86_64_PC32 autoremove_wake_function-0x4
Either way the function pointer is denoted by a relocation, so objtool
just reads that.
However there are some "lea xxx(%rip)" cases which don't use relocations
because they're referencing code in the same translation unit. Objtool
doesn't have visibility to those.
The only currently known instances of that are a few hand-coded asm text
references which don't actually need ENDBR. So it's not actually a
problem at the moment.
However if we enable -fpie, the compiler would start generating them and
there would definitely be bugs in the IBT sealing.
Detect non-relocated text references and handle them appropriately.
[ Note: I removed the manual static_call_tramp check -- that should
already be handled by the noendbr check. ]
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Add --deepest-idle-state to manpage and mention libcpupower dependency
in README.txt.
Link: https://lore.kernel.org/20241017140914.3200454-7-tglozar@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Add option to limit deepest idle state on CPUs where timerlat is running
for the duration of the workload.
Link: https://lore.kernel.org/20241017140914.3200454-5-tglozar@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Add functions to utils.c to disable idle states through functions of
libcpupower. This will serve as the basis for disabling idle states
per cpu when running timerlat.
Link: https://lore.kernel.org/20241017140914.3200454-4-tglozar@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
If libcpupower is present, set HAVE_LIBCPUPOWER_SUPPORT macro to allow
features depending on libcpupower in rtla.
Link: https://lore.kernel.org/20241017140914.3200454-3-tglozar@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Add the ability to detect the presence of libcpupower on a system to
the Makefiles in tools/build.
Link: https://lore.kernel.org/20241017140914.3200454-2-tglozar@redhat.com
Signed-off-by: Tomas Glozar <tglozar@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The interface of power_supply_hwmon.c is only meant to be used by the
psy core. Remove it from the public header file and use the private one
instead.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241017-power-supply-cleanups-v2-1-cb0f5deab088@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Now the attr tests are shell tests move the associated python and
configuration files. Update the installation build rules for the new
directories. Recycle the lib install rules for python files allowing
the explicit attr.py install line to be dropped.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: zhaimingbing <zhaimingbing@cmss.chinamobile.com>
Cc: Howard Chu <howardchu95@gmail.com>
Cc: Ze Gao <zegao2021@gmail.com>
Cc: Weilin Wang <weilin.wang@intel.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Leo Yan <leo.yan@linux.dev>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Veronika Molnarova <vmolnaro@redhat.com>
Link: https://lore.kernel.org/r/20241015000158.871828-4-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Remove the C wrapper now a shell script wrapper exists. Move
perf_event_attr dumping functions to evsel.c and reduce the scope of
variables/defines. Use fprintf to avoid snprintf complexities in
WRITE_ASS.
Add __SANE_USERSPACE_TYPES__ to evsel.c to fix format flag issues on
PowerPC triggered by moving attr.c functions to evsel.c.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: zhaimingbing <zhaimingbing@cmss.chinamobile.com>
Cc: Howard Chu <howardchu95@gmail.com>
Cc: Ze Gao <zegao2021@gmail.com>
Cc: Weilin Wang <weilin.wang@intel.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Leo Yan <leo.yan@linux.dev>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Veronika Molnarova <vmolnaro@redhat.com>
Link: https://lore.kernel.org/r/20241015000158.871828-3-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The "Setup struct perf_event_attr" test in attr.c does a bunch of
directory finding to set up running a python test that in general is
more brittle than similar logic we have in shell tests. Add a shell
test that invokes and runs the tests in the python attr.py script.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: zhaimingbing <zhaimingbing@cmss.chinamobile.com>
Cc: Howard Chu <howardchu95@gmail.com>
Cc: Ze Gao <zegao2021@gmail.com>
Cc: Weilin Wang <weilin.wang@intel.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Leo Yan <leo.yan@linux.dev>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Veronika Molnarova <vmolnaro@redhat.com>
Link: https://lore.kernel.org/r/20241015000158.871828-2-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
