Firmware is updated to send HSMP_ERR_PREREQ_NOT_SATISFIED(0xFD) and
HSMP_ERR_SMU_BUSY(0xFC) error codes. Add them here.
Add error logs to make it easy to understand the failure reason for
different error conditions.
Replace pr_err() with dev_err() to identify the driver printing the
error.
Signed-off-by: Suma Hegde <suma.hegde@amd.com>
Reviewed-by: Naveen Krishna Chatradhi <naveenkrishna.chatradhi@amd.com>
Link: https://lore.kernel.org/r/20241112120450.2407125-1-suma.hegde@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add documentation for the amd_3d_vcache sysfs bus platform driver
interface so that userspace applications can use it to change mode
preferences, either frequency or cache.
Co-developed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20241112170307.3745777-3-Basavaraj.Natikar@amd.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
AMD X3D processors, also known as AMD 3D V-Cache, feature dual Core
Complex Dies (CCDs) and enlarged L3 cache, enabling dynamic mode
switching between Frequency and Cache modes. To optimize performance,
implement the AMD 3D V-Cache Optimizer, which allows selecting either:
Frequency mode: cores within the faster CCD are prioritized before
those in the slower CCD.
Cache mode: cores within the larger L3 CCD are prioritized before
those in the smaller L3 CCD.
Co-developed-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20241112170307.3745777-2-Basavaraj.Natikar@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Since gcc supports flag out operands for inline assemblies there is always
the question when this feature should be used and if it is worth all the
ifdefs that come with that.
In order to avoid that provide similar macros like x86 which can be used
for all inline assemblies which extract the condition code. Depending on
compiler features the generated code will either always contain an ipm+srl
instruction pair, which extracts the condition code, or alternatively let
the compiler handle this completely.
Suggested-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The current "measurement_chars" CHPID sysfs attribute exposes only a
limited, validity-filtered portion of data from the associated Channel-
Measurements Characteristics Block (CMCB). New machine models add data
that is relevant for userspace tooling to the "header"-portion of the
CMCB. This data that is not currently accessible to userspace.
To prevent having to add new sysfs attributes whenever a new bit of data
is added to the CMCB "header", add a new sysfs attribute named
"measurement_chars_full" that exposes the full, unfiltered CMCB.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
OEMs can use the spk-id-gpios ACPI property to indicate the type of
speakers fitted to a device.
Attempt to read a spk-id value using the GPIO method when a usable
spk-id value is not obtained from the 01fa-spk-id-val ACPI property.
Obtaining the spk-id value has been moved earlier in the function to the
other sidecar block, so that an -EPROBE_DEFER from a GPIO driver is
handled more efficiently.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20241112131434.678882-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases the code uses goto labels to just return an error code.
Replace those with direct return:s and drop unneeded goto labels.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/20241110210040.18918-7-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we iterate through nports the iterator variable is effectively
being not used outside of the loop. Make it clear by moving its definition
into the for-loop. This makes code cleaner as well.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/20241110210040.18918-6-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use a temporary variable for the struct device pointers to avoid
dereferencing. This makes code a bit neater.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/20241110210040.18918-5-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device reset assert and deassert length was created by usleep_range()
but that does not ensure optimal handling of all the different values from
device tree properties. By switching to the new flexible sleeping helper
function, fsleep(), the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
While at it, move out GPIO consumer name setting of the reset conditional,
the all necessary checks are already done there, so logically that call is
not related to the reset sequence.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/20241110210040.18918-4-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver does not actively manage regulator state past probe() time,
so we can use devm_regulator_get_enable() to simplify the code.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/20241110210040.18918-3-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use 2-argument strscpy(), which is not only shorter but also provides
an additional check that destination buffer is an array.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/20241110210040.18918-2-andy.shevchenko@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The kdump kernel is broken on SME systems with CONFIG_IMA_KEXEC=y enabled.
Debugging traced the issue back to
b69a2afd5a ("x86/kexec: Carry forward IMA measurement log on kexec").
Testing was previously not conducted on SME systems with CONFIG_IMA_KEXEC
enabled, which led to the oversight, with the following incarnation:
...
ima: No TPM chip found, activating TPM-bypass!
Loading compiled-in module X.509 certificates
Loaded X.509 cert 'Build time autogenerated kernel key: 18ae0bc7e79b64700122bb1d6a904b070fef2656'
ima: Allocated hash algorithm: sha256
Oops: general protection fault, probably for non-canonical address 0xcfacfdfe6660003e: 0000 [#1] PREEMPT SMP NOPTI
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.11.0-rc2+ #14
Hardware name: Dell Inc. PowerEdge R7425/02MJ3T, BIOS 1.20.0 05/03/2023
RIP: 0010:ima_restore_measurement_list
Call Trace:
<TASK>
? show_trace_log_lvl
? show_trace_log_lvl
? ima_load_kexec_buffer
? __die_body.cold
? die_addr
? exc_general_protection
? asm_exc_general_protection
? ima_restore_measurement_list
? vprintk_emit
? ima_load_kexec_buffer
ima_load_kexec_buffer
ima_init
? __pfx_init_ima
init_ima
? __pfx_init_ima
do_one_initcall
do_initcalls
? __pfx_kernel_init
kernel_init_freeable
kernel_init
ret_from_fork
? __pfx_kernel_init
ret_from_fork_asm
</TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---
...
Kernel panic - not syncing: Fatal exception
Kernel Offset: disabled
Rebooting in 10 seconds..
Adding debug printks showed that the stored addr and size of ima_kexec buffer
are not decrypted correctly like:
ima: ima_load_kexec_buffer, buffer:0xcfacfdfe6660003e, size:0xe48066052d5df359
Three types of setup_data info
— SETUP_EFI,
- SETUP_IMA, and
- SETUP_RNG_SEED
are passed to the kexec/kdump kernel. Only the ima_kexec buffer
experienced incorrect decryption. Debugging identified a bug in
early_memremap_is_setup_data(), where an incorrect range calculation
occurred due to the len variable in struct setup_data ended up only
representing the length of the data field, excluding the struct's size,
and thus leading to miscalculation.
Address a similar issue in memremap_is_setup_data() while at it.
[ bp: Heavily massage. ]
Fixes: b3c72fc9a7 ("x86/boot: Introduce setup_indirect")
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20240911081615.262202-3-bhe@redhat.com
Christoph Hellwig <hch@lst.de> says:
This fixes one (of multiple) sparse warnings in fs-writeback.c, and
then reshuffles the code a bit that only the proper high level API
instead of low-level helpers is exported.
* patches from https://lore.kernel.org/r/20241112054403.1470586-1-hch@lst.de:
writeback: wbc_attach_fdatawrite_inode out of line
writeback: add a __releases annoation to wbc_attach_and_unlock_inode
Link: https://lore.kernel.org/r/20241112054403.1470586-1-hch@lst.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
Jeff Layton <jlayton@kernel.org> says:
Meta has some internal logging that scrapes /proc/self/mountinfo today.
I'd like to convert it to use listmount()/statmount(), so we can do a
better job of monitoring with containers. We're missing some fields
though. This patchset adds them.
* patches from https://lore.kernel.org/r/20241111-statmount-v4-0-2eaf35d07a80@kernel.org:
fs: add the ability for statmount() to report the sb_source
fs: add the ability for statmount() to report the fs_subtype
fs: don't let statmount return empty strings
Link: https://lore.kernel.org/r/20241111-statmount-v4-0-2eaf35d07a80@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
/proc/self/mountinfo displays the source for the mount, but statmount()
doesn't yet have a way to return it. Add a new STATMOUNT_SB_SOURCE flag,
claim the 32-bit __spare1 field to hold the offset into the str[] array.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20241111-statmount-v4-3-2eaf35d07a80@kernel.org
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Sky Huang says:
====================
Re-organize MediaTek ethernet phy drivers and propose mtk-phy-lib
This patchset comes from patch 1/9, 3/9, 4/9, 5/9 and 7/9 of:
https://lore.kernel.org/netdev/20241004102413.5838-1-SkyLake.Huang@mediatek.com/
This patchset changes MediaTek's ethernet phy's folder structure and
integrates helper functions, including LED & token ring manipulation,
into mtk-phy-lib.
---
Change in v2:
- Add correct Reviewed-by tag in each patch.
Change in v3:
[patch 4/5]
- Fix kernel test robot error by adding missing MTK_NET_PHYLIB.
====================
Signed-off-by: Sky Huang <skylake.huang@mediatek.com>
This patch adds MT7530 & MT7531's PHY ID macros in mtk-ge.c so that
it follows the same rule of mtk-ge-soc.c.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch integrates read/write page helper functions as MTK phy lib.
They are basically the same in mtk-ge.c & mtk-ge-soc.c.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes parens around TRIGGER_NETDEV_RX/TRIGGER_NETDEV_TX in
mtk_phy_led_hw_ctrl_set(), which improves readability.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates mtk-phy-lib.c & mtk-phy.h and integrates mtk-ge-soc.c's
LED helper functions so that we can use those helper functions in other
MTK's ethernet phy driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organize MediaTek ethernet phy driver files and get ready to integrate
some common functions and add new 2.5G phy driver.
mtk-ge.c: MT7530 Gphy on MT7621 & MT7531 Gphy
mtk-ge-soc.c: Built-in Gphy on MT7981 & Built-in switch Gphy on MT7988
mtk-2p5ge.c: Planned for built-in 2.5G phy on MT7988
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241104190505.272805-2-robh@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In the function gxp_timer_init, the 'int' type cast in front of the
PTR_ERR() macro is redundant, thus remove it.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20241107074619.2714-1-tangbin@cmss.chinamobile.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
of_find_compatible_node() increments the node's refcount, and it must be
decremented again with a call to of_node_put() when the pointer is no
longer required to avoid leaking the resource.
Instead of adding the missing calls to of_node_put() in all execution
paths, use the cleanup attribute for 'arm_timer' by means of the
__free() macro, which automatically calls of_node_put() when the
variable goes out of scope.
Fixes: 25de4ce5ed ("clocksource/drivers/timer-ti-dm: Handle dra7 timer wrap errata i940")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241031-timer-ti-dm-systimer-of_node_put-v3-1-063ee822b73a@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Convert the Actions Semi Owl timer bindings to DT schema.
Changes during conversion:
- Add a description
- Add "clocks" as a required property, since the driver searches for it
- Correct the given example according to owl-s500.dtsi
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241103123513.2890107-1-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
System Tick Counter is present on Ralink SoCs RT3352 and MT7620. This
driver has been in 'arch/mips/ralink' directory since the beggining of
Ralink architecture support. However, it can be moved into a more proper
place in 'drivers/clocksource'. Hence add it here adding also support for
compile test targets and reducing LOC in architecture code folder.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20241028203643.191268-2-sergio.paracuellos@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In a multi-cluster MIPS system, there are multiple GICs - one in each
cluster - each of which has its independent counter. The counters in
each GIC are not synchronized in any way, so they can drift relative
to one another through the lifetime of the system. This is problematic
for a clock source which ought to be global.
Avoid problems by always accessing cluster 0's counter, using
cross-cluster register access. This adds overhead so it is applied only
on multi-cluster systems.
Signed-off-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: Chao-ying Fu <cfu@wavecomp.com>
Signed-off-by: Dragan Mladjenovic <dragan.mladjenovic@syrmia.com>
Signed-off-by: Aleksandar Rikalo <arikalo@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20241019071037.145314-6-arikalo@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
