Alongside new drivers and device support there are several large
cleanups going on across the IIO tree and we see part of some of those
in this pull request.
Merged char-misc-next at point of 6.12-rc6 merge to avoid a
conflict with a fix for the ad7380 merged earlier this cycle.
Note that I previously messed this merge up and had to reconstruct
it this morning so a coherent pull request was possible. The new
stuff is all the same as has been in linux-next for some time with
the exception of the kernel-doc related __private ordering fix
that went in yesterday.
New device support
==================
adi,ad7380
- Support for adaq4370-4 and adaq4370 quad channel ADCs.
adi,ad7606
- Various cleanups preceeding support of AD7607, AD7608 and AD7609 ADCs.
adi,ad7779
- New driver supproting AD7770, AD7771 and AD7779 ADCs.
allegro,als31300
- New driver for this 3D Linear Hall Effect sensor.
bosch,bmi270
- Add support BMI260 which is similar but requires a different firmware image.
bosch,smi240
- New driver for this IMU.
ti,opt3001
- Add support opt3002 light sensor which has a wider spectral range than
the opt3001.
vishay,veml3235
- New driver for this ambient light sensor.
Features
========
hid-sensors
- Add support Human Proximity Range and Attention detection (requiring
a new classification style channel type)
adi,ad3552r
- Add backend support and related platform driver to support use
with an FPGA IP to allow QSPI + DDR bus operation and much higher
data aquisition rates. (various rework preceeded this feature)
adi,ad7606
- Various cleanup prior to enabling use with an IIO Backend and PWM trigger
enabling much higher speed data capture.
bosch,bme680
- Support control of preheat current
- Support triggered buffer capture
- Add SCALE and RAW channels (needed to enable the buffered capture).
bosch,bmp280
- Enable sleeping to save power.
- Add interrupt support for bmp3xx and bmp5xx devices. Also update bmp085
to new approach.
- Enable data ready trigger.
bosch,bmi270
- Add triggered buffer support
- Add scale and sampling frequency control.
vishay,veml6070
- Support integration time via DT binding for an external resistor value.
Cleanup and minor fixes
=======================
core
- Fix a longstanding issue with event codes for differential channels.
Note that not all drivers are yet fixed, but macros have been added
to avoid potential repeats of this in future.
- Tidy up handling in iio_read_acpi_mount matrix.
- Mark iio_dev::priv with __private. Later move the marking before the
field name to avoid a kernel-doc issue.
treewide
- Drop some pointless default n entries in Kconfig.
- Add an iio_get_acpi_device_name_and_data() handler to replace some
commonly repeated code.
- simplify use of 'state' in write_event_config() callback as it is
effectively a boolean. Once done make it a boolean (lots of drivers
were updated to enable this)
- some more use of devm_regulator_get_enable_read_voltage( to replace
open coded versions. Where this enables it convert all of remove
handling to devm based and drop the remove callback.
- check returns from devm_mutex_init()
accel drivers
- Use aligned_s64 instead of s64 __aligned(8)
adi,ad5791
- Add some missing GPIOs and power supplies that presumably were always
hard wired on previous boards.
- Refactor to use chip_info in device id tables.
- Convert probe entirely to devm based simplify code and allowing remove()
callback to be dropped.
adi,ad7192
- Check return from spi_get_device_match_data()
adi,ad74413r
- Don't keep an unnecessary copy of the gpio after probe.
- Use devm_regulator_get_enable_read_voltage() instead of open coding.
- Apply cleanup.h approach to reduce complexity.
adi,dac8460
- Fix a wrong compaitble ID due to a stray space.
- Add an spi_device_id table.
bosch,bmc150
- Drop some likely false ACPI IDs.
- Drop left over unused ACPI specific code.
bosch,bme680
- Add mising regmap.h include.
- Reduce excessive sleep on startup.
- Drop some cammelcase usage.
- Use fsleep
- Generalize read functions to allow for reuse.
- Use s16 variable to avoid some incorrect casting
bosch,bmg150
- Drop some likely false ACPI IDs.
bosch,bmi270
- Drop unused FREQUENCY and SCALE attributes that always returned an
error (they wil be back impelmented correctly).
- Factor out the chip specific data into a structure to enable simple
support for additional devices.
isil,isl29018
- Drop ACPI_PTR() and CONFIG_ACPI guards as not worth the trouble for very
minor saving.
invensense,mpu6050
- Use much simpler test for ACPI firmware.
kionix,kxcjk-1013
- Drop unnecessary ACPI entry in the i2c_device_id table.
- Drop support KX022-1020 to fix a bug that was introduced with that change.
Hopefully a fixed version will replace it soon.
- Drop CONFIG guards for PM in favor of pm_ptr() and the compiler removing
dead code.
- Switch from enum to chip_info structure and add ODR times to that structure.
- Deduplicate one of those ODR structures
- Drop ACPI_PTR() and move ID table out of config guards.
- Minor additional cleanup.
liteon,ltr401
- Drop some likely false ACPI Ids and add LTER0303 which is know to be in use.
microchip,pac1934
- Use much simpler test for ACPI firmware.
vishay,veml6070
- Use unsigned int instead of just unsigned.
- Use FIELD_PREP to make setting of field value explicit.
Various other minor fixes to documentation
-----BEGIN PGP SIGNATURE-----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=tB/u
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.13b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 2nd set of new device support, features and cleanup for 6.13
Alongside new drivers and device support there are several large
cleanups going on across the IIO tree and we see part of some of those
in this pull request.
Merged char-misc-next at point of 6.12-rc6 merge to avoid a
conflict with a fix for the ad7380 merged earlier this cycle.
Note that I previously messed this merge up and had to reconstruct
it this morning so a coherent pull request was possible. The new
stuff is all the same as has been in linux-next for some time with
the exception of the kernel-doc related __private ordering fix
that went in yesterday.
New device support
==================
adi,ad7380
- Support for adaq4370-4 and adaq4370 quad channel ADCs.
adi,ad7606
- Various cleanups preceeding support of AD7607, AD7608 and AD7609 ADCs.
adi,ad7779
- New driver supproting AD7770, AD7771 and AD7779 ADCs.
allegro,als31300
- New driver for this 3D Linear Hall Effect sensor.
bosch,bmi270
- Add support BMI260 which is similar but requires a different firmware image.
bosch,smi240
- New driver for this IMU.
ti,opt3001
- Add support opt3002 light sensor which has a wider spectral range than
the opt3001.
vishay,veml3235
- New driver for this ambient light sensor.
Features
========
hid-sensors
- Add support Human Proximity Range and Attention detection (requiring
a new classification style channel type)
adi,ad3552r
- Add backend support and related platform driver to support use
with an FPGA IP to allow QSPI + DDR bus operation and much higher
data aquisition rates. (various rework preceeded this feature)
adi,ad7606
- Various cleanup prior to enabling use with an IIO Backend and PWM trigger
enabling much higher speed data capture.
bosch,bme680
- Support control of preheat current
- Support triggered buffer capture
- Add SCALE and RAW channels (needed to enable the buffered capture).
bosch,bmp280
- Enable sleeping to save power.
- Add interrupt support for bmp3xx and bmp5xx devices. Also update bmp085
to new approach.
- Enable data ready trigger.
bosch,bmi270
- Add triggered buffer support
- Add scale and sampling frequency control.
vishay,veml6070
- Support integration time via DT binding for an external resistor value.
Cleanup and minor fixes
=======================
core
- Fix a longstanding issue with event codes for differential channels.
Note that not all drivers are yet fixed, but macros have been added
to avoid potential repeats of this in future.
- Tidy up handling in iio_read_acpi_mount matrix.
- Mark iio_dev::priv with __private. Later move the marking before the
field name to avoid a kernel-doc issue.
treewide
- Drop some pointless default n entries in Kconfig.
- Add an iio_get_acpi_device_name_and_data() handler to replace some
commonly repeated code.
- simplify use of 'state' in write_event_config() callback as it is
effectively a boolean. Once done make it a boolean (lots of drivers
were updated to enable this)
- some more use of devm_regulator_get_enable_read_voltage( to replace
open coded versions. Where this enables it convert all of remove
handling to devm based and drop the remove callback.
- check returns from devm_mutex_init()
accel drivers
- Use aligned_s64 instead of s64 __aligned(8)
adi,ad5791
- Add some missing GPIOs and power supplies that presumably were always
hard wired on previous boards.
- Refactor to use chip_info in device id tables.
- Convert probe entirely to devm based simplify code and allowing remove()
callback to be dropped.
adi,ad7192
- Check return from spi_get_device_match_data()
adi,ad74413r
- Don't keep an unnecessary copy of the gpio after probe.
- Use devm_regulator_get_enable_read_voltage() instead of open coding.
- Apply cleanup.h approach to reduce complexity.
adi,dac8460
- Fix a wrong compaitble ID due to a stray space.
- Add an spi_device_id table.
bosch,bmc150
- Drop some likely false ACPI IDs.
- Drop left over unused ACPI specific code.
bosch,bme680
- Add mising regmap.h include.
- Reduce excessive sleep on startup.
- Drop some cammelcase usage.
- Use fsleep
- Generalize read functions to allow for reuse.
- Use s16 variable to avoid some incorrect casting
bosch,bmg150
- Drop some likely false ACPI IDs.
bosch,bmi270
- Drop unused FREQUENCY and SCALE attributes that always returned an
error (they wil be back impelmented correctly).
- Factor out the chip specific data into a structure to enable simple
support for additional devices.
isil,isl29018
- Drop ACPI_PTR() and CONFIG_ACPI guards as not worth the trouble for very
minor saving.
invensense,mpu6050
- Use much simpler test for ACPI firmware.
kionix,kxcjk-1013
- Drop unnecessary ACPI entry in the i2c_device_id table.
- Drop support KX022-1020 to fix a bug that was introduced with that change.
Hopefully a fixed version will replace it soon.
- Drop CONFIG guards for PM in favor of pm_ptr() and the compiler removing
dead code.
- Switch from enum to chip_info structure and add ODR times to that structure.
- Deduplicate one of those ODR structures
- Drop ACPI_PTR() and move ID table out of config guards.
- Minor additional cleanup.
liteon,ltr401
- Drop some likely false ACPI Ids and add LTER0303 which is know to be in use.
microchip,pac1934
- Use much simpler test for ACPI firmware.
vishay,veml6070
- Use unsigned int instead of just unsigned.
- Use FIELD_PREP to make setting of field value explicit.
Various other minor fixes to documentation
* tag 'iio-for-6.13b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (153 commits)
iio: Move __private marking before struct element priv in struct iio_dev
docs: iio: ad7380: add adaq4370-4 and adaq4380-4
iio: adc: ad7380: add support for adaq4370-4 and adaq4380-4
iio: adc: ad7380: use local dev variable to shorten long lines
iio: adc: ad7380: fix oversampling formula
dt-bindings: iio: adc: ad7380: add adaq4370-4 and adaq4380-4 compatible parts
iio: chemical: bme680: Add support for preheat current
iio: chemical: bme680: Add triggered buffer support
iio: chemical: bme680: Add SCALE and RAW channels
iio: chemical: bme680: refactorize set_mode() mode
iio: events: make IIO_EVENT_CODE macro private
iio: accel: mma9553: use specialized event code macros
iio: dummy: use specialized event code macros
iio: adc: ad7280a: use IIO_DIFF_EVENT_CODE macro helper
iio: events.h: add event identifier macros for differential channel
iio: magnetometer: add Allegro MicroSystems ALS31300 3-D Linear Hall Effect driver
dt-bindings: iio: magnetometer: document the Allegro MicroSystems ALS31300 3-D Linear Hall Effect Sensor
dt-bindings: vendor-prefixes: Add Allegro MicroSystems, Inc
iio: light: apds9960: remove useless return
iio: light: apds9960: convert als_int and pxs_int to bool
...
This can lead to out of bounds writes since frames of this type were not
taken into account when calculating the size of the frames buffer in
uvc_parse_streaming.
Fixes: c0efd23292 ("V4L/DVB (8145a): USB Video Class driver")
Signed-off-by: Benoit Sevens <bsevens@google.com>
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Banana Pi P2 Pro is the SBC made by Shenzhen SINOVOIP based on
Rockchip RK3308.
Banana Pi P2 Pro features:
- Rockchip RK3308B-S
- DDR3 512 MB
- eMMC 8 GB
- 100M lan + onboard PoE
- 40 pin and 12 pin headers
- AP6256 BT + WIFI
- TF card slot
- 2x USB 2.0 (Type-C OTG and Type-A)
- Headphone jack
Add support for Banana Pi P2 Pro.
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
Link: https://lore.kernel.org/r/20241030202144.629956-3-dmt.yashin@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
BBanana Pi P2 Pro is the SBC made by Shenzhen SINOVOIP based on
Rockchip RK3308.
Banana Pi P2 Pro features:
- Rockchip RK3308B-S
- DDR3 512 MB
- eMMC 8 GB
- 100M lan + onboard PoE
- 40 pin and 12 pin headers
- AP6256 BT + WIFI
- TF card slot
- 2x USB 2.0 (Type-C OTG and Type-A)
- Headphone jack
Add devicetree binding for Banana Pi P2 Pro.
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241030202144.629956-2-dmt.yashin@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add new SoC dtsi file for the RK3566T variant of the Rockchip RK3566 SoC.
The difference between the RK3566T variant and the "full-fat" RK3566 variant
is in fewer supported CPU and GPU OPPs on the RK3566T, and in the absence of
a functional NPU, which we currently don't have to worry about.
Examples of the boards based on the RK3566T include the Pine64 Quartz64 Zero
SBC, [1] which is yet to be supported, the Radxa ROCK 3C, and the Radxa ZERO
3E/3W SBCs, which are both already supported. Though, Radxa doesn't mention
the use of RK3566T officially, but its official SBC specifications do state
that the maximum frequency for the Cortex-A55 cores on those SBCs is lower
than the "full-fat" RK3566's 1.8 GHz, which makes spotting the presence of
the RK3566T SoC variant rather easy. [2][3][4] An additional, helpful cue
is that Radxa handles the CPU and GPU OPPs for the RK3566T variant separately
in its downstream kernel source. [5]
The CPU and GPU OPPs supported on the RK3566T SoC variant are taken from the
vendor kernel source, [6] which uses the values of the "opp-supported-hw" OPP
properties to determine which ones are supported on a particular SoC variant.
The actual values of the "opp-supported-hw" properties make it rather easy
to see what OPPs are supported on the RK3566T SoC variant, but that, rather
unfortunately, clashes with the maximum frequencies advertised officially
for the Cortex-A55 CPU cores on the above-mentioned SBCs. [1][2][3][4] The
vendor kernel source indicates that the maximum frequency for the CPU cores
is 1.4 GHz, while the SBC specifications state that to be 1.6 GHz. Until
that discrepancy is resolved somehow, let's take the safe approach and use
the lower maximum frequency for the CPU cores.
Update the dts files of the currently supported RK3566T-based boards to use
the new SoC dtsi for the RK3566T variant. This actually takes the CPU cores
and the GPUs found on these boards out of their earlier overclocks, but it
also means that the officially advertised specifications [1][2][3][4] of the
highest supported frequencies for the Cortex-A55 CPU cores on these boards
may actually be wrong, as already explained above.
The correctness of the introduced changes was validated by decompiling and
comparing all affected board dtb files before and after these changes.
[1] https://wiki.pine64.org/wiki/Quartz64
[2] https://dl.radxa.com/rock3/docs/hw/3c/radxa_rock3c_product_brief.pdf
[3] https://dl.radxa.com/zero3/docs/hw/3e/radxa_zero_3e_product_brief.pdf
[4] https://dl.radxa.com/zero3/docs/hw/3w/radxa_zero_3w_product_brief.pdf
[5] 2dfd51da47
[6] https://raw.githubusercontent.com/rockchip-linux/kernel/f8b9431ee38ed561650be7092ab93f564598daa9/arch/arm64/boot/dts/rockchip/rk3568.dtsi
Cc: TL Lim <tllim@pine64.org>
Cc: Marek Kraus <gamiee@pine64.org>
Cc: Tom Cubie <tom@radxa.com>
Cc: FUKAUMI Naoki <naoki@radxa.com>
Helped-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Helped-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/a85b9bdc176c542fea261fe7ef37697aebb42e8b.1730516702.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rename the Rockchip RK356x SoC dtsi files and, consequently, adjust their
contents appropriately, to prepare them for the ability to specify different
CPU and GPU OPPs for each of the supported RK356x SoC variants.
The first new RK356x SoC variant to be introduced is the RK3566T, which the
Pine64 Quartz64 Zero SBC is officially based on. [1] Some other SBCs are
also based on the RK3566T variant, including Radxa ROCK 3C and ZERO 3E/3W,
but the slight trouble is that Radxa doesn't state that officially. Though,
it's rather easy to spot the RK3566T on such boards, because their official
specifications state that the maximum frequency for the Cortex-A55 cores is
lower than the "full-fat" RK3566's 1.8 GHz. [2][3][4]
These changes follow the approach used for the Rockchip RK3588 SoC variants,
which was introduced and described further in commit def88eb4d8 ("arm64:
dts: rockchip: Prepare RK3588 SoC dtsi files for per-variant OPPs"). Please
see that commit for a more detailed explanation.
No functional changes are introduced, which was validated by decompiling and
comparing all affected board dtb files before and after these changes. In
more detail, the affected dtb files have some of their blocks shuffled around
a bit and some of their phandles have different values, as a result of the
changes to the order in which the building blocks from the parent dtsi files
are included, but they effectively remain the same as the originals.
As a side note, due to the nature of introduced changes, this commit is a bit
more readable when viewed using the --break-rewrites option for git-log(1).
[1] https://wiki.pine64.org/wiki/Quartz64
[2] https://dl.radxa.com/rock3/docs/hw/3c/radxa_rock3c_product_brief.pdf
[3] https://dl.radxa.com/zero3/docs/hw/3e/radxa_zero_3e_product_brief.pdf
[4] https://dl.radxa.com/zero3/docs/hw/3w/radxa_zero_3w_product_brief.pdf
Related-to: def88eb4d8 ("arm64: dts: rockchip: Prepare RK3588 SoC dtsi files for per-variant OPPs")
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/77e7450b8280bbdf4e2dc47366c9da85d4d8d1de.1730516702.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for voltage ranges to the CPU, GPU and DMC OPPs defined in the
SoC dtsi for Rockchip OP1, as a variant of the Rockchip RK3399. This may be
useful if there are any OP1-based boards whose associated voltage regulators
are unable to deliver the exact voltages; otherwise, it causes no functional
changes to the resulting OPP voltages at runtime.
These changes cannot cause stability issues or any kind of damage, because
it's perfectly safe to use the highest voltage from an OPP group for each OPP
in the same group. The only possible negative effect of using higher voltages
is wasted energy in form of some additionally generated heat.
Reported-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/dbee35c002bda99e44f8533623d94f202a60da95.1730881777.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct the audio name for the Indiedroid Nova from
rockchip,es8388-codec to rockchip,es8388. This name change corrects a
kernel log error of "ASoC: driver name too long 'rockchip,es8388-codec'
-> 'rockchip_es8388'".
Fixes: 3900160e16 ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20241031150505.967909-2-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is to avoid tripping up kernel-doc which filters it out before
but not after the name.
Note the formatting is less than ideal as a result so we may revisit
in future.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adding documentation for adaq4370-4 and adaq4380-4 supported devices. In
particular, document the reference voltage mechanism and the gain
parameter that are specific to adaq devices.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241030-ad7380-add-adaq4380-4-support-v4-5-864ff02babae@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
adaq4370-4 (2MSPS) and adaq4380-4 (4MSPS) are quad-channel precision data
acquisition signal chain μModule solutions compatible with the ad738x
family, with the following differences:
- pin selectable gain in front of each 4 adc
- internal reference is 3V derived from refin-supply (5V)
- additional supplies
This implies that IIO_CHAN_INFO_SCALE can not be shared by type for
these new devices.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241030-ad7380-add-adaq4380-4-support-v4-4-864ff02babae@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The formula in the datasheet for oversampling time conversion seems to
be valid when device is at full speed using the maximum number of SDO
lines. The driver currently support only 1 SDO line. The correct formula
is: t_convert = T_CONVERT_0_NS + T_CONVERT_X_NS*(x -
1)*num_channel/number_of_sdo_lines.
It will produce larger delays than what is currently set, but some devices
actually require it.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241030-ad7380-add-adaq4380-4-support-v4-2-864ff02babae@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
adaq4370-4 (2MSPS) and adaq4380-4 (4MSPS) are quad-channel precision data
acquisition signal chain μModule solutions compatible with the ad738x
family, with the following differences:
- pin selectable gain in front of each 4 adc
- internal reference is 3V derived from refin-supply (5V)
- additional supplies
To select the gain a new patternProperties is added to describe each
channel. It is restricted to adaq devices.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241030-ad7380-add-adaq4380-4-support-v4-1-864ff02babae@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ensure initialization to avoid compiler warnings about potential use
of uninitialized variables.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Yoshihiro Furudera <fj5100bi@fujitsu.com>
Cc: Howard Chu <howardchu95@gmail.com>
Cc: Ze Gao <zegao2021@gmail.com>
Cc: Changbin Du <changbin.du@huawei.com>
Cc: Junhao He <hejunhao3@huawei.com>
Cc: Weilin Wang <weilin.wang@intel.com>
Cc: James Clark <james.clark@linaro.org>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20241109003759.473460-2-irogers@google.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Update the comments in sched_ext_ops to clarify this table is for
a BPF scheduler and a userland scheduler should also rely on the
sched_ext_ops table through the BPF scheduler.
Signed-off-by: Changwoo Min <changwoo@igalia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
Hi,
A recent attempt to fix a missing symbol when
CONFIG_SND_SOC_SDCA=m and CONFIG_SND_SOC_ACPI_INTEL_SDCA_QUIRKS=y
caused unmet direct dependency warning with randconig.
The reason is that SND_SOC_ACPI_INTEL_MATCH is needed to be compilable
even if ACPI is not selected, modules have dependency on exported
symbols from it.
The only solution for these kconfig dependencies seams to be to
only select SND_SOC_SDCA if ACPI is enabled from
SND_SOC_ACPI_INTEL_SDCA_QUIRKS.
Regards,
Peter
---
Peter Ujfalusi (2):
ASoC: Intel: Kconfig: Only select SND_SOC_SDCA if ACPI is enabled
ASoC: Intel: Kconfig: Revert make SND_SOC_ACPI_INTEL_MATCH depend on
ACPI
sound/soc/intel/Kconfig | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)
--
2.47.0
Add handling of clock related to secondary MI2S_RX in
sm8250_snd_startup().
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241018025452.1362293-2-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
- Allow tripless thermal zones defined in a DT to be registered in
accordance with the thermal DT bindings (Icenowy Zheng).
- Annotate LMH IRQs with lockdep classes to prevent lockdep from
reporting a possible recursive locking issue that cannot really
occur (Dmitry Baryshkov).
- Improve the thermal library "make clean" to remove a leftover
symbolic link created during compilation and fix the sampling
handler invocation in that library to pass the correct pointer
to it (Emil Dahl Juhl, zhang jiao).
-----BEGIN PGP SIGNATURE-----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=Fu7b
-----END PGP SIGNATURE-----
Merge tag 'thermal-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix one issue in the qcom lmh thermal driver, a DT handling
issue in the thermal core and two issues in the userspace thermal
library:
- Allow tripless thermal zones defined in a DT to be registered in
accordance with the thermal DT bindings (Icenowy Zheng)
- Annotate LMH IRQs with lockdep classes to prevent lockdep from
reporting a possible recursive locking issue that cannot really
occur (Dmitry Baryshkov)
- Improve the thermal library "make clean" to remove a leftover
symbolic link created during compilation and fix the sampling
handler invocation in that library to pass the correct pointer to
it (Emil Dahl Juhl, zhang jiao)"
* tag 'thermal-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/of: support thermal zones w/o trips subnode
tools/lib/thermal: Remove the thermal.h soft link when doing make clean
tools/lib/thermal: Fix sampling handler context ptr
thermal/drivers/qcom/lmh: Remove false lockdep backtrace
Fix the asymmetric CPU capacity support code in the intel_pstate driver,
added during this develompent cycle, to address a corner case in which
the capacity of a CPU going online is not updated (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----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=4Ngn
-----END PGP SIGNATURE-----
Merge tag 'pm-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix the asymmetric CPU capacity support code in the intel_pstate
driver, added during this develompent cycle, to address a corner case
in which the capacity of a CPU going online is not updated (Rafael
Wysocki)"
* tag 'pm-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Update asym capacity for CPUs that were offline initially
cpufreq: intel_pstate: Clear hybrid_max_perf_cpu before driver registration
Fix the ACPI processor driver initialization ordering after recent
changes to avoid calling init_freq_invariance_cppc() too early on
AMD platforms (Mario Limonciello).
-----BEGIN PGP SIGNATURE-----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=VPlW
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix the ACPI processor driver initialization ordering after recent
changes to avoid calling init_freq_invariance_cppc() too early on AMD
platforms (Mario Limonciello)"
* tag 'acpi-6.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Move arch_init_invariance_cppc() call later
-----BEGIN PGP SIGNATURE-----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=zTn6
-----END PGP SIGNATURE-----
Merge tag 'v6.12-rc6-ksmbd-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
"Four fixes, all also marked for stable:
- fix two potential use after free issues
- fix OOM issue with many simultaneous requests
- fix missing error check in RPC pipe handling"
* tag 'v6.12-rc6-ksmbd-fixes' of git://git.samba.org/ksmbd:
ksmbd: check outstanding simultaneous SMB operations
ksmbd: fix slab-use-after-free in smb3_preauth_hash_rsp
ksmbd: fix slab-use-after-free in ksmbd_smb2_session_create
ksmbd: Fix the missing xa_store error check
Some PCs with Intel N100 (with PCI device 8086:461c, DID_ADL_N_SKU4)
experienced issues with error interrupts not working, even with the
following configuration in the BIOS.
In-Band ECC Support: Enabled
In-Band ECC Operation Mode: 2 (make all requests protected and
ignore range checks)
IBECC Error Injection Control: Inject Correctable Error on insertion
counter
Error Injection Insertion Count: 251658240 (0xf000000)
Add polling mode support for these machines to ensure that memory error
events are handled.
Signed-off-by: Orange Kao <orange@aiven.io>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/all/20241106114024.941659-3-orange@aiven.io
Currently, igen6_edac sets edac_op_state to EDAC_OPSTATE_NMI, while the
driver also supports memory errors reported from Machine Check. Initialize
edac_op_state to the correct value according to the configuration data
that the driver probed.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/all/20241106114024.941659-2-orange@aiven.io
On 2 x Intel Sapphire Rapids machines with 224 logical CPUs, a poorly
behaving BPF scheduler can live-lock the system by making multiple CPUs bang
on the same DSQ to the point where soft-lockup detection triggers before
SCX's own watchdog can take action. It also seems possible that the machine
can be live-locked enough to prevent scx_ops_helper, which is an RT task,
from running in a timely manner.
Implement scx_softlockup() which is called when three quarters of
soft-lockup threshold has passed. The function immediately enables the ops
breather and triggers an ops error to initiate ejection of the BPF
scheduler.
The previous and this patch combined enable the kernel to reliably recover
the system from live-lock conditions that can be triggered by a poorly
behaving BPF scheduler on Intel dual socket systems.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
A poorly behaving BPF scheduler can live-lock the system by e.g. incessantly
banging on the same DSQ on a large NUMA system to the point where switching
to the bypass mode can take a long time. Turning on the bypass mode requires
dequeueing and re-enqueueing currently runnable tasks, if the DSQs that they
are on are live-locked, this can take tens of seconds cascading into other
failures. This was observed on 2 x Intel Sapphire Rapids machines with 224
logical CPUs.
Inject artifical delays while the bypass mode is switching to guarantee
timely completion.
While at it, move __scx_ops_bypass_lock into scx_ops_bypass() and rename it
to bypass_lock.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Valentin Andrei <vandrei@meta.com>
Reported-by: Patrick Lu <patlu@meta.com>
In the bpf_out_neigh_v6 function, rcu_read_lock() is used to begin an RCU
read-side critical section. However, when unlocking, one branch
incorrectly uses a different RCU unlock flavour rcu_read_unlock_bh()
instead of rcu_read_unlock(). This mismatch in RCU locking flavours can
lead to unexpected behavior and potential concurrency issues.
This possible bug was identified using a static analysis tool developed
by myself, specifically designed to detect RCU-related issues.
This patch corrects the mismatched unlock flavour by replacing the
incorrect rcu_read_unlock_bh() with the appropriate rcu_read_unlock(),
ensuring that the RCU critical section is properly exited. This change
prevents potential synchronization issues and aligns with proper RCU
usage patterns.
Fixes: 09eed1192c ("neighbour: switch to standard rcu, instead of rcu_bh")
Signed-off-by: Jiawei Ye <jiawei.ye@foxmail.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/tencent_CFD3D1C3D68B45EA9F52D8EC76D2C4134306@qq.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Pull sched_ext/for-6.12-fixes to receive 0e7ffff1b8 ("scx: Fix raciness in
scx_ops_bypass()"). Planned updates for scx_ops_bypass() depends on it.
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no reason to use a bitwise AND when checking the conditions to
enable NUMA optimization for the built-in CPU idle selection policy, so
use a logical AND instead.
Fixes: f6ce6b9493 ("sched_ext: Do not enable LLC/NUMA optimizations when domains overlap")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/lkml/20241108181753.GA2681424@thelio-3990X/
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Two small fixes, the drivers one in ufs simply delays running a work
queue and the generic one in zoned storage switches to a more correct
API that tries the standard buddy allocator first (for small
allocations); this fixes an allocation problem with small allocations
seen under memory pressure.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZy5pZSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdonAQCeHKnp
BkxbSls2uPQn4DAxak1tCfxTujMFWxQHP2Y92gEA2q3chF7P136z2rYp0wGfm7P4
ivxddAWZth4tV7TUUw8=
=by5B
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes, the drivers one in ufs simply delays running a work
queue and the generic one in zoned storage switches to a more correct
API that tries the standard buddy allocator first (for small
allocations); this fixes an allocation problem with small allocations
seen under memory pressure"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Start the RTC update work later
scsi: sd_zbc: Use kvzalloc() to allocate REPORT ZONES buffer
amdgpu:
- Brightness fix
- DC vbios parsing fix
- ACPI fix
- SMU 14.x fix
- Power workload profile fix
- GC partitioning fix
- Debugfs fixes
imagination:
- Track PVR context per file
- Break ref-counting cycle
panel-orientation-quirks:
- Fix matching Lenovo Yoga Tab 3 X90F
panthor:
- Lock VM array
- Be strict about I/O mapping flags
xe:
- Fix ccs_mode setting for Xe2 and later
- Synchronize ccs_mode setting with client creation
- Apply scheduling WA for LNL in additional places as needed
- Fix leak and lock handling in error paths of xe_exec ioctl
- Fix GGTT allocation leak leading to eventual crash in SR-IOV
- Move run_ticks update out of job handling to avoid synchronization
with reader
-----BEGIN PGP SIGNATURE-----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=/7AA
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2024-11-09' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Weekly fixes, usual leaders in amdgpu and xe, then a panel quirk, and
some fixes to imagination and panthor drivers. Seems around the usual
level for this time and don't know of any big problems.
amdgpu:
- Brightness fix
- DC vbios parsing fix
- ACPI fix
- SMU 14.x fix
- Power workload profile fix
- GC partitioning fix
- Debugfs fixes
imagination:
- Track PVR context per file
- Break ref-counting cycle
panel-orientation-quirks:
- Fix matching Lenovo Yoga Tab 3 X90F
panthor:
- Lock VM array
- Be strict about I/O mapping flags
xe:
- Fix ccs_mode setting for Xe2 and later
- Synchronize ccs_mode setting with client creation
- Apply scheduling WA for LNL in additional places as needed
- Fix leak and lock handling in error paths of xe_exec ioctl
- Fix GGTT allocation leak leading to eventual crash in SR-IOV
- Move run_ticks update out of job handling to avoid synchronization
with reader"
* tag 'drm-fixes-2024-11-09' of https://gitlab.freedesktop.org/drm/kernel: (23 commits)
drm/panthor: Be stricter about IO mapping flags
drm/panthor: Lock XArray when getting entries for the VM
drm: panel-orientation-quirks: Make Lenovo Yoga Tab 3 X90F DMI match less strict
drm/xe: Stop accumulating LRC timestamp on job_free
drm/xe/pf: Fix potential GGTT allocation leak
drm/xe: Drop VM dma-resv lock on xe_sync_in_fence_get failure in exec IOCTL
drm/xe: Fix possible exec queue leak in exec IOCTL
drm/amdgpu: add missing size check in amdgpu_debugfs_gprwave_read()
drm/amdgpu: Adjust debugfs eviction and IB access permissions
drm/amdgpu: Adjust debugfs register access permissions
drm/amdgpu: Fix DPX valid mode check on GC 9.4.3
drm/amd/pm: correct the workload setting
drm/amd/pm: always pick the pptable from IFWI
drm/amdgpu: prevent NULL pointer dereference if ATIF is not supported
drm/amd/display: parse umc_info or vram_info based on ASIC
drm/amd/display: Fix brightness level not retained over reboot
drm/xe/guc/tlb: Flush g2h worker in case of tlb timeout
drm/xe/ufence: Flush xe ordered_wq in case of ufence timeout
drm/xe: Move LNL scheduling WA to xe_device.h
drm/xe: Use the filelist from drm for ccs_mode change
...
With warnings added for deprecated #address-cells/#size-cells handling,
the DT address handling code causes warnings when used on nodes with no
address. This happens frequently with calls to of_platform_populate() as
it is perfectly acceptable to have devices without a 'reg' property. The
desired behavior is to just silently return an error when retrieving an
address.
The warnings can be avoided by checking for "#address-cells" presence
first and checking for an address property before fetching
"#address-cells" and "#size-cells".
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Steven Price <steven.price@arm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20241108193547.2647986-2-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
We've observed an NFS server shrink the TCP window and then reset the TCP
connection as part of a HA failover. When the connection has TLS, often
the NFS client will hang indefinitely in this stack:
wait_woken+0x70/0x80
wait_on_pending_writer+0xe4/0x110 [tls]
tls_sk_proto_close+0x368/0x3a0 [tls]
inet_release+0x54/0xb0
__sock_release+0x48/0xc8
sock_close+0x20/0x38
__fput+0xe0/0x2f0
__fput_sync+0x58/0x70
xs_reset_transport+0xe8/0x1f8 [sunrpc]
xs_tcp_shutdown+0xa4/0x190 [sunrpc]
xprt_autoclose+0x68/0x170 [sunrpc]
process_one_work+0x180/0x420
worker_thread+0x258/0x368
kthread+0x104/0x118
ret_from_fork+0x10/0x20
This hang prevents the client from closing the socket and reconnecting to
the server.
Because xs_nospace() elevates sk_write_pending, and sk_sndtimeo is
MAX_SCHEDULE_TIMEOUT, tls_sk_proto_close is never able to complete its wait
for pending writes to the socket. For this case where we are resetting the
transport anyway, we don't expect the socket to ever have write space, so
fix this by simply clearing the sock's sndtimeo under the sock's lock.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tracepoint strings don't require newlines (and in fact, they are
undesirable).
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Add the __counted_by compiler attribute to the flexible array member
buckets to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Compile-tested only.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
