Implement the enum_frame_size pad operation.
The sensor supports a continuous size range of resolutions.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Alvium camera by default is in free running mode. Datasheet say that
acquisition frame rate reg can only be used if frame start trigger
mode is set to off.
Enable r/w acquisition frame rate and turn off trigger mode.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
[Sakari Ailus: Fix spelling of "acquisition".]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acquisition frame rate enable reg have a very long name let's reduce this
with an abbreviation.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
[Sakari Ailus: Fix spelling of "acquisition".]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Instead of reading device_fw reg as multiple regs let's read the entire
64bit reg using one i2c read and use bit masks and bit shifts to get fw
info.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The privacy status is maintained by privacy_ctrl, on which all
of the privacy status changes will go through, so there is no
point in maintaining one more element any more.
Reported-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Prior to the ongoing command privacy is on, it would return -1 to
indicate the current privacy status, and the ongoing command would
be well executed by firmware as well, so this is not error. This
patch changes its behavior to notify privacy on directly by V4L2
privacy control instead of reporting error.
Fixes: 29006e196a ("media: pci: intel: ivsc: Add CSI submodule")
Cc: stable@vger.kernel.org # for 6.6 and later
Reported-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There're possibilities that privacy status change notification happens
in the middle of the ongoing mei command which already takes the command
lock, but v4l2_ctrl_s_ctrl() would also need the same lock prior to this
patch, so this may results in circular locking problem. This patch adds
one dedicated lock for v4l2 control handler to avoid described issue.
Fixes: 29006e196a ("media: pci: intel: ivsc: Add CSI submodule")
Cc: stable@vger.kernel.org # for 6.6 and later
Reported-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Tested-by: Jason Chen <jason.z.chen@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
clang 19 complains about the missing parameter name. Let's add it.
drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-debugfs.h:19:62: warning: omitting the parameter name in a function definition is a C23 extension [-Wc23-extensions]
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406050908.1kL1C69p-lkp@intel.com/
Fixes: e22b4973ee ("media: c8sectpfe: Do not depend on DEBUG_FS")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/tuners/tda9887.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/radio/si470x/radio-si470x-common.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/pci/ttpci/budget-core.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/pci/bt8xx/bt878.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/pci/ivtv/ivtvfb.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/usb/go7007/go7007.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/usb/go7007/go7007-usb.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/pci/saa7134/saa7134-empress.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/pci/saa7134/saa7134-go7007.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/pci/saa7134/saa7134-alsa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/pci/saa7134/saa7134-dvb.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/platform/marvell/mcam-core.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/platform/marvell/mmp_camera.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Return value of function 'i2c_transfer' is not checked that
may cause undefined behaviour.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2cf36ac447 ("[PATCH] v4l: 656: added support for the following cards")
Signed-off-by: Aleksandr Burakov <a.burakov@rosalinux.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Describe LVDS data mapping of the LVDS-to-DPI decoder input port.
This fixes a warning reported by lvds-codec driver:
"
lvds-codec lvds-decoder: missing 'data-mapping' DT property
"
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reorder the SAI dma-names to ensure "rx" precedes "tx" as required to fixes
the DTB_CHECK warning.
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: audio-controller@f100000: dma-names:1: 'tx' was expected
from schema $id: http://devicetree.org/schemas/sound/fsl,sai.yaml#
arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: audio-controller@f110000: dma-names:1: 'tx' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the undocumented compatible string 'fsl,ls-pcie-ep' property from
the ls1028a device tree source to fix DTB_CHECK warnings.
arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: pcie-ep@3400000: compatible: ['fsl,ls1028a-pcie-ep', 'fsl,ls-pcie-ep'] is too long
from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie-ep.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The only key that should wake up the phone is power button press. This
prevents accidental wakeup due to e.g. pressing the buttons in the
pocket or backpack and is in line what userspace uses to unblank the
device.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The kmemleak code sometimes complains about the following leak:
unreferenced object 0xffff8000102e0000 (size 32768):
comm "swapper/0", pid 1, jiffies 4294937323 (age 71.240s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000db9a88a3>] __vmalloc_node_range+0x324/0x450
[<00000000ff8903a4>] __vmalloc_node+0x90/0xd0
[<000000001a06634f>] arm64_efi_rt_init+0x64/0xdc
[<0000000007826a8d>] do_one_initcall+0x178/0xac0
[<0000000054a87017>] do_initcalls+0x190/0x1d0
[<00000000308092d0>] kernel_init_freeable+0x2c0/0x2f0
[<000000003e7b99e0>] kernel_init+0x28/0x14c
[<000000002246af5b>] ret_from_fork+0x10/0x20
The memory object in this case is for efi_rt_stack_top and is allocated
in an initcall. So this is certainly a false positive. Mark the object
as not a leak to quash it.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The logic in __efi_memmap_init() is shared between two different
execution flows:
- mapping the EFI memory map early or late into the kernel VA space, so
that its entries can be accessed;
- the x86 specific cloning of the EFI memory map in order to insert new
entries that are created as a result of making a memory reservation
via a call to efi_mem_reserve().
In the former case, the underlying memory containing the kernel's view
of the EFI memory map (which may be heavily modified by the kernel
itself on x86) is not modified at all, and the only thing that changes
is the virtual mapping of this memory, which is different between early
and late boot.
In the latter case, an entirely new allocation is created that carries a
new, updated version of the kernel's view of the EFI memory map. When
installing this new version, the old version will no longer be
referenced, and if the memory was allocated by the kernel, it will leak
unless it gets freed.
The logic that implements this freeing currently lives on the code path
that is shared between these two use cases, but it should only apply to
the latter. So move it to the correct spot.
While at it, drop the dummy definition for non-x86 architectures, as
that is no longer needed.
Cc: <stable@vger.kernel.org>
Fixes: f0ef652347 ("efi: Fix efi_memmap_alloc() leaks")
Tested-by: Ashish Kalra <Ashish.Kalra@amd.com>
Link: https://lore.kernel.org/all/36ad5079-4326-45ed-85f6-928ff76483d3@amd.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
EFI runtime services are remapped into the lower 1 GiB of virtual
address space at boot, so they are guaranteed to be able to co-exist
with the kernel virtual mappings without the need to allocate space for
them in the kernel's vmalloc region, which is rather small.
This means those mappings are covered by TTBR0 when LPAE PAN is enabled,
and so 'user' access must be enabled while such calls are in progress.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
This node is unused and origins from downstream kernel where it is
used for the DSP.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We cannot use /delete-node/ directive to delete a node in a DT
overlay. The node won't be deleted effectively. Instead, set
the node's status property to "disabled" to achieve something
similar.
Fixes: eeb403df95 ("ARM: dts: imx53-qsb: add support for the HDMI expander")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable HDMI output on i.MX8MP DHCOM PDK2 and PDK3. The I2C5 on PDK2 and
I2C mux port 1 on PDK3 respectively are used in regular I2C mode instead
of HDMI DDC mode to permit connection of other I2C devices on those buses.
The pinctrl_hdmi node is part of the SoM DTSI already.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IMX8MP_CLK_CLKOUT2 supplies the TC9595 bridge with 13 MHz reference
clock. The IMX8MP_CLK_CLKOUT2 is supplied from IMX8MP_AUDIO_PLL2_OUT.
The IMX8MP_CLK_CLKOUT2 operates only as a power-of-two divider, and the
current 156 MHz is not power-of-two divisible to achieve 13 MHz.
To achieve 13 MHz output from IMX8MP_CLK_CLKOUT2, set IMX8MP_AUDIO_PLL2_OUT
to 208 MHz, because 208 MHz / 16 = 13 MHz.
Fixes: 20d0b83e71 ("arm64: dts: imx8mp: Add TC9595 bridge on DH electronics i.MX8M Plus DHCOM")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Panel timing bindings do not allow 'panel-name' and there seems to be no
users of it: neither Linux kernel drivers, nor U-boot as of
v2024.07-rc2.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Panel timing bindings do not allow 'u-boot,panel-name' and there seems
to be no users of it: neither Linux kernel drivers, nor U-boot as of
v2024.07-rc2. Reported by dtbs_check:
imx6qp-tx6qp-8037.dtb: display-timings: timing-et0700: 'u-boot,panel-name' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LG4573 panel bindings do not allow 'power-on-delay' property. Linux
driver does not use it, either. Reported by dtbs_check:
imx6dl-aristainetos2_4.dtb: display@0: Unevaluated properties are not allowed ('power-on-delay' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bindings and Linux driver expect native-mode to be a phandle to one of
the timings node, not a boolean property. Correct the DTS to fix
dtbs_check warnings like:
imx53-m53evk.dtb: display-timings: timing-800x480p60: 'native-mode' does not match any of the regexes: 'pinctrl-[0-9]+'
This should not have actual effect for Linux kernel (no real bug
affecting choice of native-mode), because the first timing node is
chosen in absence of proper native-mode property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DT schema expects panel timings node to follow certain pattern,
dtbs_check warnings:
imx6dl-gw54xx.dtb: display-timings: 'hsd100pxn1' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
Linux drivers do not care about node name, so this should not have
effect on Linux.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initialize audio PLL1 as the parent clock for 8kHz series rates,
audio PLL2 as the parent clock for 11kHz series rates. that PLL1
and PLL2 can together support full range of audio sample rates.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The bus reset event occurs in the bus managed by one of 1394 OHCI
controller in Linux system, however the existing tracepoints events has
the lack of data about it to distinguish the issued hardware from the
others.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-9-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The asynchronous transmission of phy packet is initiated on one of 1394
OHCI controller, however the existing tracepoints events has the lack of
data about it.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-8-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The asynchronous transmission of phy packet is initiated on one of 1394
OHCI controller, however the existing tracepoints events has the lack of
data about it.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The asynchronous transmission of phy packet is initiated on one of 1394
OHCI controller, however the existing tracepoints events has the lack of
data about it.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The asynchronous transaction is initiated on one of 1394 OHCI
controller, however the existing tracepoints events has the lack of data
about it.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The asynchronous transaction is initiated on one of 1394 OHCI controller,
however the existing tracepoints events has the lack of data about it.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The asynchronous transaction is initiated on one of 1394 OHCI controller,
however the existing tracepoints events has the lack of data about it.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
The asynchronous transaction is initiated on one of 1394 OHCI controller,
however the existing tracepoints events has the lack of data about it.
This commit adds card_index member into event structure to store the index
of host controller in use, and prints it.
Link: https://lore.kernel.org/r/20240613131440.431766-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
We only use the mapping in a single context in a short and contained scope,
so kmap_local_page is sufficient and cheaper. This will also allow
skb_datagram_iter to be called from softirq context.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://lore.kernel.org/r/20240613113504.1079860-1-sagi@grimberg.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Petr Machata says:
====================
mlxsw: Handle MTU values
Amit Cohen writes:
The driver uses two values for maximum MTU, but neither is accurate.
In addition, the value which is configured to hardware is not calculated
correctly. Handle these issues and expose accurate values for minimum
and maximum MTU per netdevice.
Add test cases to check that the exposed values are really supported.
Patch set overview:
Patches #1-#3 set the driver to use accurate values for MTU
Patch #4 aligns the driver to always use the same value for maximum MTU
Patch #5 adds a test
====================
Link: https://lore.kernel.org/r/cover.1718275854.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add cases to check minimum and maximum MTU which are exposed via
"ip -d link show". Test configuration and traffic. Use VLAN devices as
usually VLAN header (4 bytes) is not included in the MTU, and drivers
should configure hardware correctly to send maximum MTU payload size
in VLAN tagged packets.
$ ./min_max_mtu.sh
TEST: ping [ OK ]
TEST: ping6 [ OK ]
TEST: Test maximum MTU configuration [ OK ]
TEST: Test traffic, packet size is maximum MTU [ OK ]
TEST: Test minimum MTU configuration [ OK ]
TEST: Test traffic, packet size is minimum MTU [ OK ]
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/89de8be8989db7a97f3b39e3c9da695673e78d2e.1718275854.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the driver uses two different values for maximum MTU, one is
stored in mlxsw_port->dev->max_mtu and the second is stored in
mlxsw_port->max_mtu. The second one is set to value which is queried from
firmware. This value was never tested, and unfortunately is not really
supported. That means that with the existing code, user can set MTU to
X, which is not really supported by firmware and which is bigger than
buffer size which is allocated in pci.
To make the driver consistent, use only mlxsw_port->dev->max_mtu for
maximum MTU value, for buffers headroom add Ethernet frame headers, which
are not included in mlxsw_port->dev->max_mtu. Remove mlxsw_port->max_mtu.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/89fa6f804386b918d337e736e14ac291bb947483.1718275854.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the driver uses ETH_MAX_MTU as maximum MTU of netdevices,
instead, use the accurate value which is supported by the driver.
Subtract Ethernet headers which are taken into account by hardware for
MTU checking, as described in the previous patch.
Set minimum MTU to ETH_MIN_MTU, as zero MTU is not really supported.
With this change:
a. The stack will do the MTU checking, so we can remove it from the driver.
b. User space will be able to query the actual MTU limits.
Before this patch:
$ ip -j -d link show dev swp1 | jq | grep mtu
"mtu": 1500,
"min_mtu": 0,
"max_mtu": 65535,
With this patch:
$ ip -j -d link show dev swp1 | jq | grep mtu
"mtu": 1500,
"min_mtu": 68,
"max_mtu": 10218,
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/be8232e38c196ecb607f82c5e000ea427ce22abb.1718275854.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethernet frame consists of - Ethernet header, payload, FCS. The MTU value
which is used by user is the size of the payload, which means that when
user sets MTU to X, the total frame size will be larger due to the addition
of the Ethernet header and FCS.
Spectrum ASICs take into account Ethernet header and FCS as part of packet
size for MTU check. Adjust MTU value when user sets MTU, to configure the
MTU size which is required by hardware. The Tx header length which was used
by the driver is not relevant for such calculation, take into account
Ethernet header (with VLAN extension) and FCS.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/f3203c2477bb8ed18b1e79642fa3e3713e1e55bb.1718275854.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>