There's no reason why only a clock of 19.2MHz is supported.
Indeed this isn't even a frequency listed in the datasheet.
Add support for 24MHz as well.
The PLL settings result in slightly different link frequencies,
so parameterise those.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Out of all the registers that are defined for each mode, only around
10 differ between the modes.
Split the table into common and mode specific ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The values and ranges of V4L2_CID_VBLANK are all computed,
so there is no reason for it to be a read only control.
Remove the register values from the mode lists, add the
handler, and remove the read only flag.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The device tree bindings define the relevant regulators for the
sensor, so update the driver to request the regulators and control
them at the appropriate times.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Registers 0x0202 and 0x0203 are written via the control handler
for V4L2_CID_EXPOSURE, so are not needed from the mode lists.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The binned modes set DIG_CROP_X_OFFSET and DIG_CROP_IMAGE_WIDTH
to less than the full image, even though the image being captured
is meant to be a scaled version of the full array size.
Reduce X_OFFSET to 0, and increase IMAGE_WIDTH to the full array.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The output image is defined as being 4208x3118 pixels in size.
Y_ADD_STA register was set to 0, and Y_ADD_END to 3118, giving
3119 lines total.
The datasheet lists a requirement for Y_ADD_STA to be a multiple
of a power of 2 depending on binning/scaling mode (2 for full pixel,
4 for x2-bin/scale, 8 for (x2-bin)+(x2-subsample) or x4-bin, or 16
for (x4-bin)+(x2-subsample)).
(Y_ADD_END – Y_ADD_STA + 1) also has to be a similar power of 2.
The current configuration for the full res modes breaks that second
requirement, and we can't increase Y_ADD_STA to 1 to retain exactly
the same field of view as that then breaks the first requirement.
For the binned modes, they are worse off as 3118 is not a multiple of
4.
Increase the main mode to 4208x3120 so that it is the same FOV as the
binned modes, with Y_ADD_STA at 0.
Fix Y_ADD_STA and Y_ADD_END for the binned modes so that they meet the
sensor requirements.
This does change the Bayer order as the default configuration is for
H&V flips to be enabled, so readout is from Y_STA_END to Y_ADD_STA,
and this patch has changed Y_STA_END.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The IMX258_FLL_* defines are unused. Remove them.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luis Garcia <git@luigi311.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In v4l2_async_create_ancillary_links(), ancillary links are created for
lens and flash sub-devices. These are sub-device to sub-device links and
if the async notifier is related to a V4L2 device, the source sub-device
of the ancillary link is NULL, leading to a NULL pointer dereference.
Check the notifier's sd field is non-NULL in
v4l2_async_create_ancillary_links().
Fixes: aa4faf6eb2 ("media: v4l2-async: Create links during v4l2_async_match_notify()")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
[Sakari Ailus: Reword the subject and commit messages slightly.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The current code does not return anything to the user.
Although the code looks a bit dangerous (using a pointer without
checking if it is valid), it should be fine. The core validates that
sel->pad has a valid value.
Fix the following smatch error:
drivers/media/i2c/hi846.c:1854 hi846_get_selection() warn: statement has no effect 31
Fixes: e8c0882685 ("media: i2c: add driver for the SK Hynix Hi-846 8M pixel camera")
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[Sakari Ailus: code -> core.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently we have the following algorithm to calculate what value should be
written to the exposure control of imx412.
lpfr = imx412->vblank + imx412->cur_mode->height;
shutter = lpfr - exposure;
The 'shutter' value is given to IMX412_REG_EXPOSURE_CIT however, the above
algorithm will result in the value given to IMX412_REG_EXPOSURE_CIT
decreasing as the requested exposure value from user-space goes up.
e.g.
[ 2255.713989] imx412 20-001a: Received exp 1608, analog gain 0
[ 2255.714002] imx412 20-001a: Set exp 1608, analog gain 0, shutter 1938, lpfr 3546
[ 2256.302770] imx412 20-001a: Received exp 2586, analog gain 100
[ 2256.302800] imx412 20-001a: Set exp 2586, analog gain 100, shutter 960, lpfr 3546
[ 2256.753755] imx412 20-001a: Received exp 3524, analog gain 110
[ 2256.753772] imx412 20-001a: Set exp 3524, analog gain 110, shutter 22, lpfr 3546
This behaviour results in the image having less exposure as the requested
exposure value from user-space increases.
Other sensor drivers such as ov5675, imx218, hid556 and others take the
requested exposure value and use the value directly.
Take the example of the above cited sensor drivers and directly apply the
requested exposure value from user-space. The 'lpfr' variable still
functions as before but the 'shutter' variable can be dispensed with as a
result.
Once done a similar run of the test application requesting higher exposure
looks like this, with 'exp' written directly to the sensor.
[ 133.207884] imx412 20-001a: Received exp 1608, analog gain 0
[ 133.207899] imx412 20-001a: Set exp 1608, analog gain 0, lpfr 3546
[ 133.905309] imx412 20-001a: Received exp 2844, analog gain 100
[ 133.905344] imx412 20-001a: Set exp 2844, analog gain 100, lpfr 3546
[ 134.241705] imx412 20-001a: Received exp 3524, analog gain 110
[ 134.241775] imx412 20-001a: Set exp 3524, analog gain 110, lpfr 3546
The result is then setting the sensor exposure to lower values results in
darker, less exposure images and vice versa with higher exposure values.
Fixes: 9214e86c0c ("media: i2c: Add imx412 camera sensor driver")
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5/imx577
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Gjorgji Rosikopulos <quic_grosikop@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
ACPI_ID_LEN is defined in mod_devicetable.h, so the header should
be guaranteed to included in ipu-bridge.h instead of the source
files which include ipu-bridge.h.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'options' has been unused since
commit fa7f7e7354 ("perf jit: Move test functionality in to a test").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20240602000505.213032-1-linux@treblig.org
Change "perf lock info" argument handling to:
Display both map and thread info (rather than an error) when neither are
specified.
Display both map and thread info (rather than just thread info) when
both are requested.
Signed-off-by: Nick Forrington <nick.forrington@arm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20240513091413.738537-2-nick.forrington@arm.com
Kui-Feng Lee says:
====================
Enable BPF programs to declare arrays of kptr, bpf_rb_root, and bpf_list_head.
Some types, such as type kptr, bpf_rb_root, and bpf_list_head, are
treated in a special way. Previously, these types could not be the
type of a field in a struct type that is used as the type of a global
variable. They could not be the type of a field in a struct type that
is used as the type of a field in the value type of a map either. They
could not even be the type of array elements. This means that they can
only be the type of global variables or of direct fields in the value
type of a map.
The patch set aims to enable the use of these specific types in arrays
and struct fields, providing flexibility. It examines the types of
global variables or the value types of maps, such as arrays and struct
types, recursively to identify these special types and generate field
information for them.
For example,
...
struct task_struct __kptr *ptr[3];
...
it will create 3 instances of "struct btf_field" in the "btf_record" of
the data section.
[...,
btf_field(offset=0x100, type=BPF_KPTR_REF),
btf_field(offset=0x108, type=BPF_KPTR_REF),
btf_field(offset=0x110, type=BPF_KPTR_REF),
...
]
It creates a record of each of three elements. These three records are
almost identical except their offsets.
Another example is
...
struct A {
...
struct task_struct __kptr *task;
struct bpf_rb_root root;
...
}
struct A foo[2];
it will create 4 records.
[...,
btf_field(offset=0x7100, type=BPF_KPTR_REF),
btf_field(offset=0x7108, type=BPF_RB_ROOT:),
btf_field(offset=0x7200, type=BPF_KPTR_REF),
btf_field(offset=0x7208, type=BPF_RB_ROOT:),
...
]
Assuming that the size of an element/struct A is 0x100 and "foo"
starts at 0x7000, it includes two kptr records at 0x7100 and 0x7200,
and two rbtree root records at 0x7108 and 0x7208.
All these field information will be flatten, for struct types, and
repeated, for arrays.
---
Changes from v6:
- Return BPF_KPTR_REF from btf_get_field_type() only if var_type is a
struct type.
- Pass btf and type to btf_get_field_type().
Changes from v5:
- Ensure field->offset values of kptrs are advanced correctly from
one nested struct/or array to another.
Changes from v4:
- Return -E2BIG for i == MAX_RESOLVE_DEPTH.
Changes from v3:
- Refactor the common code of btf_find_struct_field() and
btf_find_datasec_var().
- Limit the number of levels looking into a struct types.
Changes from v2:
- Support fields in nested struct type.
- Remove nelems and duplicate field information with offset
adjustments for arrays.
Changes from v1:
- Move the check of element alignment out of btf_field_cmp() to
btf_record_find().
- Change the order of the previous patch 4 "bpf:
check_map_kptr_access() compute the offset from the reg state" as
the patch 7 now.
- Reject BPF_RB_NODE and BPF_LIST_NODE with nelems > 1.
- Rephrase the commit log of the patch "bpf: check_map_access() with
the knowledge of arrays" to clarify the alignment on elements.
v6: https://lore.kernel.org/all/20240520204018.884515-1-thinker.li@gmail.com/
v5: https://lore.kernel.org/all/20240510011312.1488046-1-thinker.li@gmail.com/
v4: https://lore.kernel.org/all/20240508063218.2806447-1-thinker.li@gmail.com/
v3: https://lore.kernel.org/all/20240501204729.484085-1-thinker.li@gmail.com/
v2: https://lore.kernel.org/all/20240412210814.603377-1-thinker.li@gmail.com/
v1: https://lore.kernel.org/bpf/20240410004150.2917641-1-thinker.li@gmail.com/
Kui-Feng Lee (9):
bpf: Remove unnecessary checks on the offset of btf_field.
bpf: Remove unnecessary call to btf_field_type_size().
bpf: refactor btf_find_struct_field() and btf_find_datasec_var().
bpf: create repeated fields for arrays.
bpf: look into the types of the fields of a struct type recursively.
bpf: limit the number of levels of a nested struct type.
selftests/bpf: Test kptr arrays and kptrs in nested struct fields.
selftests/bpf: Test global bpf_rb_root arrays and fields in nested
struct types.
selftests/bpf: Test global bpf_list_head arrays.
kernel/bpf/btf.c | 310 ++++++++++++------
kernel/bpf/verifier.c | 4 +-
.../selftests/bpf/prog_tests/cpumask.c | 5 +
.../selftests/bpf/prog_tests/linked_list.c | 12 +
.../testing/selftests/bpf/prog_tests/rbtree.c | 47 +++
.../selftests/bpf/progs/cpumask_success.c | 171 ++++++++++
.../testing/selftests/bpf/progs/linked_list.c | 42 +++
tools/testing/selftests/bpf/progs/rbtree.c | 77 +++++
8 files changed, 558 insertions(+), 110 deletions(-)
====================
Link: https://lore.kernel.org/r/20240523174202.461236-1-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make sure global arrays of bpf_list_heads and fields of bpf_list_heads in
nested struct types work correctly.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-10-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make sure global arrays of bpf_rb_root and fields of bpf_rb_root in nested
struct types work correctly.
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-9-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make sure that BPF programs can declare global kptr arrays and kptr fields
in struct types that is the type of a global variable or the type of a
nested descendant field in a global variable.
An array with only one element is special case, that it treats the element
like a non-array kptr field. Nested arrays are also tested to ensure they
are handled properly.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-8-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Limit the number of levels looking into struct types to avoid running out
of stack space.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-7-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The verifier has field information for specific special types, such as
kptr, rbtree root, and list head. These types are handled
differently. However, we did not previously examine the types of fields of
a struct type variable. Field information records were not generated for
the kptrs, rbtree roots, and linked_list heads that are not located at the
outermost struct type of a variable.
For example,
struct A {
struct task_struct __kptr * task;
};
struct B {
struct A mem_a;
}
struct B var_b;
It did not examine "struct A" so as not to generate field information for
the kptr in "struct A" for "var_b".
This patch enables BPF programs to define fields of these special types in
a struct type other than the direct type of a variable or in a struct type
that is the type of a field in the value type of a map.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-6-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The verifier uses field information for certain special types, such as
kptr, rbtree root, and list head. These types are treated
differently. However, we did not previously support these types in
arrays. This update examines arrays and duplicates field information the
same number of times as the length of the array if the element type is one
of the special types.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-5-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Move common code of the two functions to btf_find_field_one().
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-4-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
field->size has been initialized by bpf_parse_fields() with the value
returned by btf_field_type_size(). Use it instead of calling
btf_field_type_size() again.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-3-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
reg_find_field_offset() always return a btf_field with a matching offset
value. Checking the offset of the returned btf_field is unnecessary.
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Link: https://lore.kernel.org/r/20240523174202.461236-2-thinker.li@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Several hardware monitoring chips optionally support Packet Error Checking
(PEC). For some chips, PEC support can be enabled simply by setting
I2C_CLIENT_PEC in the i2c client data structure. Others require chip
specific code to enable or disable PEC support.
Introduce hwmon_chip_pec and HWMON_C_PEC to simplify adding configurable
PEC support for hardware monitoring drivers. A driver can set HWMON_C_PEC
in its chip information data to indicate PEC support. If a chip requires
chip specific code to enable or disable PEC support, the driver only needs
to implement support for the hwmon_chip_pec attribute to its write
function.
Packet Error Checking is only supported for SMBus devices. HWMON_C_PEC
must therefore only be set by a driver if the parent device is an I2C
device. Attempts to set HWMON_C_PEC on any other device type is not
supported and rejected.
The code calls i2c_check_functionality() to check if PEC is supported
by the I2C/SMBus controller. This function is only available if CONFIG_I2C
is enabled and reachable. For this reason, the added code needs to depend
on reachability of CONFIG_I2C.
Cc: Radu Sabau <radu.sabau@analog.com>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The first fixes for v6.10. And we have a big one, I suspect the
biggest wireless pull request we ever had. There are fixes all over,
both in stack and drivers. Likely the most important here are mt76 not
working on mt7615 devices, ath11k not being able to connect to 6 GHz
networks and rtlwifi suffering from packet loss. But of course there's
much more.
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZdrSMRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuYnAgAqZMvSQKbhkYRfIua9Ygmdk8pDetEhaJg
HAUiW8ymLkWG1Md1V3tjY9Es66YeSr03Tx8xz/8pDWSaiUCdCs+u0zonhRK0sb3/
HAfyUpRIGDq/9kTM9lfL+yOTKwtRti+NmTXqeJr1CrpBejuXydRT+YYcIEmwQQxw
pm5xwLmrq74pMRE3VCTRbj2mfv/leFoDQasTeimUi6PgRrCeXSmUDy14k1zyAsI5
/uchvyvhgN54U2vIvO0RzW5zfS84cNEG+mW/+PpiuMftH2sYS1/UqT8BCQdrfzBz
PuiocUBXU68NzB4iLZhzPSDirOsYVaYpgKPfLPF1jNoj+iEQh1HhCA==
=5my7
-----END PGP SIGNATURE-----
Merge tag 'wireless-2024-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.10-rc3
The first fixes for v6.10. And we have a big one, I suspect the
biggest wireless pull request we ever had. There are fixes all over,
both in stack and drivers. Likely the most important here are mt76 not
working on mt7615 devices, ath11k not being able to connect to 6 GHz
networks and rtlwifi suffering from packet loss. But of course there's
much more.
* tag 'wireless-2024-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (37 commits)
wifi: rtlwifi: Ignore IEEE80211_CONF_CHANGE_RETRY_LIMITS
wifi: mt76: mt7615: add missing chanctx ops
wifi: wilc1000: document SRCU usage instead of SRCU
Revert "wifi: wilc1000: set atomic flag on kmemdup in srcu critical section"
Revert "wifi: wilc1000: convert list management to RCU"
wifi: mac80211: fix UBSAN noise in ieee80211_prep_hw_scan()
wifi: mac80211: correctly parse Spatial Reuse Parameter Set element
wifi: mac80211: fix Spatial Reuse element size check
wifi: iwlwifi: mvm: don't read past the mfuart notifcation
wifi: iwlwifi: mvm: Fix scan abort handling with HW rfkill
wifi: iwlwifi: mvm: check n_ssids before accessing the ssids
wifi: iwlwifi: mvm: properly set 6 GHz channel direct probe option
wifi: iwlwifi: mvm: handle BA session teardown in RF-kill
wifi: iwlwifi: mvm: Handle BIGTK cipher in kek_kck cmd
wifi: iwlwifi: mvm: remove stale STA link data during restart
wifi: iwlwifi: dbg_ini: move iwl_dbg_tlv_free outside of debugfs ifdef
wifi: iwlwifi: mvm: set properly mac header
wifi: iwlwifi: mvm: revert gen2 TX A-MPDU size to 64
wifi: iwlwifi: mvm: d3: fix WoWLAN command version lookup
wifi: iwlwifi: mvm: fix a crash on 7265
...
====================
Link: https://lore.kernel.org/r/20240603115129.9494CC2BD10@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in lib/test_rhashtable.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240531-md-lib-test_rhashtable-v1-1-cd6d4138f1b6@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
dst_cache: fix possible races
This series is inspired by various undisclosed syzbot
reports hinting at corruptions in dst_cache structures.
It seems at least four users of dst_cache are racy against
BH reentrancy.
Last patch is adding a DEBUG_NET check to catch future misuses.
====================
Link: https://lore.kernel.org/r/20240531132636.2637995-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After fixing four different bugs involving dst_cache
users, it might be worth adding a check about BH being
blocked by dst_cache callers.
DEBUG_NET_WARN_ON_ONCE(!in_softirq());
It is not fatal, if we missed valid case where no
BH deadlock is to be feared, we might change this.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
ila_output() is called from lwtunnel_output()
possibly from process context, and under rcu_read_lock().
We might be interrupted by a softirq, re-enter ila_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in seg6_output_core() is not good enough,
because seg6_output_core() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter seg6_output_core()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in seg6_input_core().
Fixes: fa79581ea6 ("ipv6: sr: fix several BUGs when preemption is enabled")
Fixes: 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Lebrun <dlebrun@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in rpl_output() is not good enough,
because rpl_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter rpl_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Apply a similar change in rpl_input().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Aring <aahringo@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 1378817486 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
Disabling preemption in ioam6_output() is not good enough,
because ioam6_output() is called from process context,
lwtunnel_output() only uses rcu_read_lock().
We might be interrupted by a softirq, re-enter ioam6_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable() instead of
preempt_disable().
Fixes: 8cb3bf8bff ("ipv6: ioam: Add support for the ip6ip6 encapsulation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Justin Iurman <justin.iurman@uliege.be>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240531132636.2637995-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we get to the end of the r8152's suspend() routine and we find that
the USB device is INACCESSIBLE then it means that some of our
preparation for suspend didn't take place. We need a USB reset to get
ourselves back in a consistent state so we can try again and that
can't happen during system suspend. Call pm_wakeup_event() to wake the
system up in this case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f25.170a0220.8b5ad.1752@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we happened to get a USB transfer error during the transition to
suspend then the usb_queue_reset_device() that r8152_control_msg()
calls will get dropped on the floor. This is because
usb_lock_device_for_reset() (which usb_queue_reset_device() uses)
silently fails if it's called when a device is suspended or if too
much time passes.
Let's resolve this by resetting the device ourselves in r8152's
resume() function.
NOTE: due to timing, it's _possible_ that we could end up with two USB
resets: the one queued previously and the one called from the resume()
patch. This didn't happen in test cases I ran, though it's conceivably
possible. We can't easily know if this happened since
usb_queue_reset_device() can just silently drop the reset request. In
any case, it's not expected that this is a problem since the two
resets can't run at the same time (because of the device lock) and it
should be OK to reset the device twice. If somehow the double-reset
causes problems we could prevent resets from being queued up while
suspend is running.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f22.170a0220.8b5ad.1750@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This commit allows rcutorture to test double-call_srcu() when the
CONFIG_DEBUG_OBJECTS_RCU_HEAD Kconfig option is enabled. The non-raw
sdp structure's ->spinlock will be acquired in call_srcu(), hence this
commit also removes the current IRQ and preemption disabling so as to
avoid lockdep complaints.
Link: https://lore.kernel.org/all/20240407112714.24460-1-qiang.zhang1211@gmail.com/
Signed-off-by: Zqiang <qiang.zhang1211@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
This reverts commit 28319d6dc5. The race
it fixed was subject to conditions that don't exist anymore since:
1612160b91 ("rcu-tasks: Eliminate deadlocks involving do_exit() and RCU tasks")
This latter commit removes the use of SRCU that used to cover the
RCU-tasks blind spot on exit between the tasklist's removal and the
final preemption disabling. The task is now placed instead into a
temporary list inside which voluntary sleeps are accounted as RCU-tasks
quiescent states. This would disarm the deadlock initially reported
against PID namespace exit.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The bypass lock contention mitigation assumes there can be at most
2 contenders on the bypass lock, following this scheme:
1) One kthread takes the bypass lock
2) Another one spins on it and increment the contended counter
3) A third one (a bypass enqueuer) sees the contended counter on and
busy loops waiting on it to decrement.
However this assumption is wrong. There can be only one CPU to find the
lock contended because call_rcu() (the bypass enqueuer) is the only
bypass lock acquire site that may not already hold the NOCB lock
beforehand, all the other sites must first contend on the NOCB lock.
Therefore step 2) is impossible.
The other problem is that the mitigation assumes that contenders all
belong to the same rdp CPU, which is also impossible for a raw spinlock.
In theory the warning could trigger if the enqueuer holds the bypass
lock and another CPU flushes the bypass queue concurrently but this is
prevented from all flush users:
1) NOCB kthreads only flush if they successfully _tried_ to lock the
bypass lock. So no contention management here.
2) Flush on callbacks migration happen remotely when the CPU is offline.
No concurrency against bypass enqueue.
3) Flush on deoffloading happen either locally with IRQs disabled or
remotely when the CPU is not yet online. No concurrency against
bypass enqueue.
4) Flush on barrier entrain happen either locally with IRQs disabled or
remotely when the CPU is offline. No concurrency against
bypass enqueue.
For those reasons, the bypass lock contention mitigation isn't needed
and is even wrong. Remove it but keep the warning reporting a contended
bypass lock on a remote CPU, to keep unexpected contention awareness.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Upon NOCB deoffloading, the rcuo kthread must be forced to sleep
until the corresponding rdp is ever offloaded again. The deoffloader
clears the SEGCBLIST_OFFLOADED flag, wakes up the rcuo kthread which
then notices that change and clears in turn its SEGCBLIST_KTHREAD_CB
flag before going to sleep, until it ever sees the SEGCBLIST_OFFLOADED
flag again, should a re-offloading happen.
Upon NOCB offloading, the rcuo kthread must be forced to wake up and
handle callbacks until the corresponding rdp is ever deoffloaded again.
The offloader sets the SEGCBLIST_OFFLOADED flag, wakes up the rcuo
kthread which then notices that change and sets in turn its
SEGCBLIST_KTHREAD_CB flag before going to check callbacks, until it
ever sees the SEGCBLIST_OFFLOADED flag cleared again, should a
de-offloading happen again.
This is all a crude ad-hoc and error-prone kthread (un-)parking
re-implementation.
Consolidate the behaviour with the appropriate API instead.
[ paulmck: Apply Qiang Zhang feedback provided in Link: below. ]
Link: https://lore.kernel.org/all/20240509074046.15629-1-qiang.zhang1211@gmail.com/
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The (de-)offloading process used to take care about the NOCB timer when
it depended on the per-rdp NOCB locking. However this isn't the case
anymore for a long while. It can now safely be armed and run during the
(de-)offloading process, which doesn't care about it anymore.
Update the comments accordingly.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
The parts explaining the bypass lifecycle in (de-)offloading are out
of date and/or wrong. Bypass is simply enabled whenever SEGCBLIST_RCU_CORE
flag is off.
Fix the comments accordingly.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
There is no direct RCU counterpart to lockdep_assert_irqs_disabled()
and friends. Although it is possible to construct them, it would
be more convenient to have the following lockdep assertions:
lockdep_assert_in_rcu_read_lock()
lockdep_assert_in_rcu_read_lock_bh()
lockdep_assert_in_rcu_read_lock_sched()
lockdep_assert_in_rcu_reader()
This commit therefore creates them.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Convention for examples is to only show what's covered by the binding,
so drop the consumer "socionext,milbeaut-usio-uart" and input clock
provider "fixed-clock" from the example. "socionext,milbeaut-usio-uart"
is also not documented by a schema which caused a warning.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240520222646.1741958-1-robh@kernel.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a MODULE_DESCRIPTION() on all drivers that miss it to avoid
modpost warnings.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240528121320.160685-1-angelogioacchino.delregno@collabora.com
Tested-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
save_area of per-CPU svm_data are dominantly accessed from their
own local CPUs, so allocate them node-local for performance reason
so rename __snp_safe_alloc_page as snp_safe_alloc_page_node which
accepts numa node id as input parameter, svm_cpu_init call it with
node id switched from cpu id
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240520120858.13117-4-lirongqing@baidu.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
The allocation for the per-CPU save area in svm_cpu_init shouldn't
be accounted, So introduce __snp_safe_alloc_page helper, which has
gfp flag as input, svm_cpu_init calls __snp_safe_alloc_page with
GFP_KERNEL, snp_safe_alloc_page calls __snp_safe_alloc_page with
GFP_KERNEL_ACCOUNT as input
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240520120858.13117-3-lirongqing@baidu.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
The input parameter 'vcpu' in snp_safe_alloc_page is not used.
Therefore, remove it.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240520120858.13117-2-lirongqing@baidu.com
Signed-off-by: Sean Christopherson <seanjc@google.com>