This patch fixes a problem where our Tools MAC Loopback test, after
driver unbind would fail. This was because the hw was configured
for multiqueue and unbind operation did not clear this configuration.
The problem is fixed by resetting this configuration in i40e_remove.
Change-ID: I130c05138319182ed1476d3a0b5222d6a6320af9
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dynamic algorithm, while now working, doesn't have good
performance in 40G mode.
One part of this patch addresses the high CPU utilization of some small
streaming workloads that the driver should reduce CPU in.
It also changes the minimum ITR that the dynamic algorithm
will settle on, causing our minimum latency to go from 12us
to about 14us, when using adaptive mode.
It also changes the BULK interrupt rate to allow maximum throughput
on a 40Gb connection with a single thread of transmit, clamping
interrupt rate to 8000 for TX makes single thread traffic go too
slow.
The new ULTRA bulk setting is introduced and is used
when the Rx packet rate on this queue exceeds 40000 packets per
second. This value of 40000 was chosen because the automatic tuning
of minimum ITR=20us means that a single queue can't quite achieve
that many packets per second from a round-robin test.
Change-ID: Icce8faa128688ca5fd2c4229bdd9726877a92ea2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was using a value expressed in 2us increments
for the divisor to figure out our bytes/usec values.
Fix the usecs variable to contain a value in microseconds.
Change-ID: I5c20493103c295d6f201947bb908add7040b7c41
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves a multi-line register setting into a function
which simplifies reading the flow of the enable function.
This also fixes a bug where the enable function was enabling
the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx.
Change-ID: Ie308f9d0d48540204590cb9d7a5a7b1196f959bb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VF driver is unable to communicate with the PF, it just gives
up and never tries again. Aside from the obvious character flaw that
this shows, it's also a lousy user experience.
When PF communications fail, wait five seconds, and try again. And
again. Don't give up, little VF driver! Your prince will come!
Change-ID: Ia1378a39879883563b8faffce819f375821f9585
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_intr and i40e/i40evf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acquire NVM, before issuing an AQ read nvm command for X722.
We need to acquire the NVM before issuing an AQ read to the NVM
otherwise we will get EBUSY from the FW. Also release when done.
This fixes the two X722 issues with respect to eeprom checksum verify
and reading NVM version info.
With this patch in place, i40e driver will provide basic support
for X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The defines from the RSS enabling call were mistakenly
missed in the patches to the i40e which should have been
to i40evf as well.
This is a follow up to (commit ed921559886dd40528) "fix
32 bit build warnings".
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a spinlock which is to be used for synchronizing
access to VSI's MAC filter list.
This patch also synchronizes execution of other codepaths which are
accessing VSI's MAC filter list with execution of
service_task:sync_vsi_filters.
In function i40e_add_vsi, copied out LAA MAC address instead of cloning
MAC filter entry because only MAC address is needed to remove MAC VLAN
filter from FW/HW.
Change-ID: I0e10ac7c715d44aa994239642aa4d57c998573a2
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BITS_RX_EN is an 'unsigned long' constant, so the ones complement of that
has bits set that do not fit into a 32-bit variable on 64-bit architectures,
which causes a harmless gcc warning:
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c: In function 'hix5hd2_port_disable':
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c:374:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel_relaxed(~(BITS_RX_EN | BITS_TX_EN), priv->base + PORT_EN);
This adds a cast to (u32) to tell gcc that the code is indeed fine.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS MDIO driver fails to build on older ARM machines that are not
yet converted to CONFIG_OF:
drivers/net/ethernet/hisilicon/hns_mdio.c: In function 'hns_mdio_bus_name':
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: error: 'OF_BAD_ADDR' undeclared (first use in this function)
u64 taddr = OF_BAD_ADDR;
^
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/hisilicon/hns_mdio.c:409:11: error: implicit declaration of function 'of_translate_address' [-Werror=implicit-function-declaration]
taddr = of_translate_address(np, addr);
^
This clarifies the dependency to ensure we don't attempt to build these
drivers without CONFIG_OF, but also adds a COMPILE_TEST alternative to
give us better build coverage testing.
Build-tested on x86 as well to ensure this actually works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations fail to build the hns dsaf code because of
a missing header file:
ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_init':
ethernet/hisilicon/hns/hns_dsaf_main.c:1096:2: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
priv->soft_mac_tbl = vzalloc(sizeof(*priv->soft_mac_tbl)
This adds the correct #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes the bug triggered timeout sequence. when the connective
ports cannot accept the packets with higher speed, they will send out the
pause frame to the Soc's mac. At that time, the driver resets the relevant
of the Soc, then it causes the packets cannot be sent out immediately.
this patch fixes the issue.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
before this patch, hns driver only permits user to set the net device
by using ethtool -s when the device is link up. it is obviously not so
good. it needs to be set no matter it is link up or down. so this patch
fixes this issue.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Chenny Xu <chenny.xu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the wrong judgement of mac_id when get port num.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the hns driver hnae sysfs interface according to
Arnd's review comments.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'bcm-phy-lib.c', added as a part of the commit
"net: phy: Add Broadcom phy library for common interfaces"
was missing the module license. This was causing an issue
when the library is built as a module; "module license
'unspecified' taints kernel".
This patch fixes the issue by adding the module license,
author and description to the bcm-phy-lib.c file.
Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for
common interfaces")
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new generation Mellanox Spectrum ASIC, 10/25/40/50 and
100Gb/s Ethernet Switch.
The initial driver implements bridge forwarding offload including
bridge internal VLAN support, FDB static entries, FDB learning and
HW ageing including their setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we currently do not support the offloading of 802.1D bridges, we
need to be able to let the device know it should not learn MAC addresses
on specific {Port, VID} pairs.
Add the SPVMLR register, which controls the learning enablement of
{Port, VID} pairs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SFDAT which is used to control switch ageing time.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for a port to support {Port, VID} to FID mapping it needs to be
configured to a virtual port mode (as opposed to VLAN mode).
Add the SVPE register, which enables port virtualization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An incoming packet can be classified into a filtering identifer (FID)
based on its VID or incoming port and VID ({Port, VID}).
Add the SVFA register, which controls this mapping.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filtering identifiers (FIDs) are unique identifers of bridge instances
in the hardware.
Add the SFMR register, which is responsible for the creation and
configuration of these FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of SBPR, SBCM, SBPM, SBMM and PBMC registers that are
used to configure shared buffers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPVID and SPVM registers responsible for default port VID
configuration and VLAN membership of a port.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SFN register which is used to poll for newly added and aged-out FDB
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SFD register which is responsible for filtering database
manipulation, including static and dynamic FDB entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing item helper which allows to access char bufs on multiple
offsets. This is needed by SFD and SFN register definitions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets destined to offloaded netdevs will be classified to FIDs in the
device and flooded in case of BUM.
The flooding table used is of type FID-offset, which allows one to
create different flooding domains for different FIDs and specify the
offset in the flooding table for each FID (not necessarily equal to FID
or VID).
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the newly introduced Spectrum switch ASIC, packets destined to not
offloaded netdevs will be classified to special FIDs (vFIDs) in the
device and flooded to the CPU port.
The flooding table used is of type per-FID, which allows one to create
different flooding domains for different vFIDs.
While using a simple single-entry flood table is certainly sufficient at
this point, we do plan to offload 802.1D bridges involving VLAN
interfaces, thus making this change necessary.
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the introduction of L2 offloads, allow different ports to
join/leave the flooding domain, according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 64 VFs, we can easily overwhelm the AQ on the PF if we have too low
a limit on the number of AQ requests. This leads to ARQ overflow errors,
and occasionally VFs that fail to initialize.
Since we really only hit this condition on initial VF driver load, the
requests that we process are lightweight, so this extra work doesn't
cause problems for the PF driver.
Change-ID: I620221520d8af987df6ace9ba938ffaf22107681
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some devices, in some systems, in some configurations, the VFs would
fail to initialize the first time you loaded the driver.
To correct this, increase the delay time for the init task slightly, and
wait longer before giving up.
If we enable VFs and load the VF driver in the same kernel as the PF
driver, we can totally overwhelm the PF driver with AQ requests because
all of the instances try to initialize at the same time.
To help alleviate this, stagger the initial scheduling of the init task
using the PCIe function as a multiplier. We mask off the function to
only three bits so no instance has to wait too long.
With these two changes, initializing 128 VFs on a single device goes
from four minutes to just a few seconds.
Change-ID: If3d8720c1c4e838ab36d8781d9ec295a62380936
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1000Base_T_Optical got added to the function that figures out what
is supported when link is down but not when link is up. Add it in there
too so that we display the correct information.
Change-ID: I85ebcdfa7c02d898c44c673b1500552a53c8042e
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vlan_features field was correctly being set to the same value as the
netdev features field. However, this was being done before the features
were actually being set up, leaving the vlan_features empty.
Also, after a reset, vlan_features will be incorrectly assigned the
previous netdev feature flags, which can contain VLAN feature bits. This
makes the VLAN code angry and will cause a stack dump.
To fix these issues, set up the netdev features first, then mask out the
VLAN feature bits when assigning vlan_features.
Change-ID: Ib0548869dc83cf6a841cb8697dd94c12359ba4d2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the number of invalid messages from a VF is exceeded, the VF
will be disabled, due to the invalid messages. This happens if
other VF drivers (like DPDK) send a message through the driver's
mailbox (aka virtchannel) interface, but the message is not
supported by the i40e pf driver, such as CONFIG_PROMISCUOUS_MODE.
This patch changes the num_invalid_msgs in struct i40e_vf to record
the continuous invalid msgs, and it will be reset when a valid msg
is received.
Change-ID: Iaec42fd3dcdd281476b3518be23261dd46fc3718
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds support for setting a new bit in the Set Local LLDP MIB AQ command
Type field. When set to 1, the bit indicates to FW that Apps should be
treated as non-willing. When 0, FW behaves as before.
Change-ID: I0d2101c1606c59c7188d3e6a0c7810e0f205233a
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an ethtool priv flag to enable and disable printing
the VEB statistics.
Change-ID: I7654054a3a73b08aa8310d94ee8fce6219107dd8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two defines that are not used are causing customer confusion - remove
them.
Change-ID: Icef0325aca8e0f4fcdfc519e026bdd375e791200
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the nvmupdate application to decide when a read or write error
should be exposed to the user. Since the application needs to use
write probes to find the ReadOnly sections on a potentially unknown NVM
version in the HW and read probes to check the status of the last write,
some error messages are expected, but need not be shown to the users.
The driver doesn't know which are ignorable from real errors, so needs
to let the application make the decision.
Change-ID: I78fca8ab672bede11c10c820b83c26adfd536d03
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.
Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.
Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per Eric Dumazet's previous patches:
(see commit (24d2e4a507) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The polling routine for i40e was rounding up the budget for Rx cleanup to
1. This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>