We don't currently support the MT ASE for microMIPS kernels, and there
are no CPUs currently in existence that use both. They can however both
be enabled in Kconfig, resulting in build failures such as:
AS arch/mips/kernel/cps-vec.o
arch/mips/kernel/cps-vec.S: Assembler messages:
arch/mips/kernel/cps-vec.S:242: Warning: the 32-bit microMIPS architecture does not support the `mt' extension
arch/mips/kernel/cps-vec.S:276: Error: unrecognized opcode `mttc0 $13,$2,2'
arch/mips/kernel/cps-vec.S:282: Error: unrecognized opcode `mttc0 $8,$1,2'
arch/mips/kernel/cps-vec.S:285: Error: unrecognized opcode `mttc0 $0,$2,1'
...
Fix this by preventing MT from being enabled when targeting microMIPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Set RX_FLAG_DECRYPTED in case of MMIC failure so that
ieee80211_rx_h_decrypt() doesnt drop the frame before getting to
ieee80211_rx_h_michael_mic_verify().
Signed-off-by: Michael Skeffington <mike@astro.ai>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rate_control_ops structure is only passed as an argument to the
function ieee80211_rate_control_{register/unregister}. This argument
is of type const, so declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add const to bin_attribute structure as it is only passed to the
functions sysfs_{remove/create}_bin_file. The corresponding arguments
are of type const, so declare the structure to be const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After association, ping is not working when sweeping the channel at the
AP side. It is caused by having incorrect carrier state (OFF) for the STA
in successful roaming. This patch sets the carrier state ON for the case.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the device/firmware supports multi-channel, it can have P2P
connection and regular connection with AP simultaneous. In this case,
the num_different_channels in wiphy info was not correct when firmware
supports multi-channel (The iw wiphy# info showed "#channels <= 1" in
interface combinations). It caused association failed and error message
"CTRL-EVENT-FREQ-CONFLICT error" in wpa_supplicant when P2P GO interface
was running at the same time.
The root cause is that the num_different_channels was always overridden
to 1 in brcmf_setup_ifmodes even multi-channel was enabled.
We correct the logic by moving num_different_channels setting forward.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When setting wpa_auth to WPA_AUTH_NONE(1) in AP mode with WEP security,
firmware will set privacy bit and add WPA OUI in VENDOR IE in beacon and
probe response. The security type in softAP beacons confuse the
supplicant in client side, and the user client will see [WPA-?] in
supplicant scan result. So we set WPA_AUTH_DISABLED in softAP mode with
OPEN security.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per below statement about p2p device address in WFA P2P
spec $2.4.3:
The P2P Device Address of a P2P Device shall be its globally
administered MAC address, or its globally administered MAC
address with the locally administered bit set.
This patch follow above statement, using a separate device
address for p2p interface
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch wrapper wps ie in pass through tlv, so that
firmware could parse correctly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 4d7ab36f0c ("mwifiex: Do not change bss_type in
change_virtual_intf") kept original bss_type unchanged. bss_num should
keep the same style, in this way. Unique tuple (bss_type, bss_num) will
be able to locate the right priv structure.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver is doing netif_carrier_off during suspend, which will set
the IFF_LOWER_UP flag to 0. As a result certain applications
will think this as a real carrier down and behave accordingly.
This will cause issues like loss of IP address, for example. To
fix this use netif_device_dettach during suspend.
Fixes: 0026b32d72 ('mwifiex: fix Tx timeout issue during suspend test')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Provision is added for configuring RTS threshold by sending
vap dynamic update frame to firmware.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BUFFER_AVAILABLE interrupt is sent by firmware to indicate
change in buffer status. We should check buffer status while
handling this interrupt. Currently buffer status is checked
only while dequeueing packets. This patch fixes a data
traffic stuck problem observed occasionally.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We get buffer full event from firmware whenever Tx queue is full
Host should stop writing packets after this and resume after
buffer free event.
Buffer status checking is optimized for once in 4 times if
BUFF_FULL condition is not set, otherwise once for every
packet.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi_sdio_check_buffer_status would be the appropriate name
for this function as we are checking hardware buffers
availability status.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for U-APSD power save. Configuration
frame is downloaded to firmware with default settings and
support is advertised to mac80211
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame set_antenna is modified to use common
descriptor structure. Also it's subframe type is set.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements rfkill_poll handler. Also, necessary changes
are done in interface up and down handler to support rfkill
functionality.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the uninitialized descriptor pointer
issue in function rsi_send_internal_mgmt_frame().
Descriptor should point to start of the skb data.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9a629fafe7 ("rsi: immediate wakeup bit and priority for TX command packets")
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No need to get into the submenu to disable all BCMA-related config entries.
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use of_device_get_match_data to identify QUP version instead
of of_device_is_compatible.
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes an issue where a SPI transaction has completed, but the
done condition is missed. This occurs because at the time of interrupt the
MAX_INPUT_DONE_FLAG is not asserted. However, in the process of reading
blocks of data from the FIFO, the last portion of data comes in.
The opflags read at the beginning of the irq handler no longer matches the
current opflag state. To get around this condition, the block read
function should update the opflags so that done detection is correct after
the return.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Much like the block mode changes, we are breaking up DMA transactions
into 64K chunks so we can reset the QUP engine.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Take specific sgl and nent to be prepared. This is in
preparation for splitting DMA into multiple transacations, this
contains no code changes just refactoring.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This let's you write more to the SPI bus than 64K-1 which is important
if the block size of a SPI device is >= 64K or some other device wants
to do something larger.
This has the benefit of completely removing spi_message from the spi-qup
transactions
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA transactions should only only need to call io_config only once, but
block mode might call it several times to setup several transactions so
it can handle reads/writes larger than the max size per transaction, so
we move the call to the do_ functions.
This is just refactoring, there should be no functional change
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is in preparation for handling transactions larger than
64K-1 bytes in block mode, which is currently unsupported and
quietly fails.
We need to break these into two functions 1) prep is
called once per spi_message and 2) io_config is called
once per spi-qup bus transaction
This is just refactoring, there should be no functional
change
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch corrects the behavior of the BLOCK
transactions. During block transactions, the controller
must be read/written to in block size transactions.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Wait to signal done until we get all of the interrupts we are expecting
to get for a transaction. If we don't wait for the input done flag, we
can be in between transactions when the done flag comes in and this can
mess up the next transaction.
While here cleaning up the code which sets controller->xfer = NULL and
restores it in the ISR. This looks to be some debug code which is not
required.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add i/o completion timeout for DMA and PIO modes.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To operate in DMA mode, the buffer should be aligned and
the size of the transfer should be a multiple of block size
(for v1). And the no. of words being transferred should
be programmed in the count registers appropriately.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable chip select support for QUP versions later than v1. The
chip select support was broken in QUP version 1. Hence the chip
select support was removed earlier in an earlier commit
(4a8573abe "spi: qup: Remove chip select function"). Since the
chip select support is functional in recent versions of QUP,
re-enabling it for QUP versions later than v1.
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ath_ps_ops structures are only stored as a reference in the ps_ops
field of a ath_common structure. This field is of type const, so make
the structures as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As the association status changes the driver needs to configure the
hardware. This is done based on information in the "sta" acquired by
ieee80211_find_sta(), which requires the caller to ensure that the "sta"
is valid while its being used; generally by entering an rcu read
section.
But the operations acting on the "sta" has to communicate with the
firmware and may therefor sleep, resulting in the following report:
[ 31.418190] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:238
[ 31.425919] in_atomic(): 0, irqs_disabled(): 0, pid: 34, name:
kworker/u8:1
[ 31.434609] CPU: 0 PID: 34 Comm: kworker/u8:1 Tainted: G W
4.12.0-rc4-next-20170607+ #993
[ 31.441002] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[ 31.450380] Workqueue: phy0 ieee80211_iface_work
[ 31.457226] Call trace:
[ 31.461830] [<ffffff8008088c58>] dump_backtrace+0x0/0x260
[ 31.464004] [<ffffff8008088f7c>] show_stack+0x14/0x20
[ 31.469557] [<ffffff8008392e70>] dump_stack+0x98/0xb8
[ 31.474592] [<ffffff80080e4330>] ___might_sleep+0xf0/0x118
[ 31.479626] [<ffffff80080e43a8>] __might_sleep+0x50/0x88
[ 31.485010] [<ffffff80088ff9a4>] mutex_lock+0x24/0x60
[ 31.490479] [<ffffff8008595c38>] wcn36xx_smd_set_link_st+0x30/0x130
[ 31.495428] [<ffffff8008591ed8>] wcn36xx_bss_info_changed+0x148/0x448
[ 31.501504] [<ffffff80088ab3c4>]
ieee80211_bss_info_change_notify+0xbc/0x118
[ 31.508102] [<ffffff80088f841c>] ieee80211_assoc_success+0x664/0x7f8
[ 31.515220] [<ffffff80088e13d4>]
ieee80211_rx_mgmt_assoc_resp+0x144/0x2d8
[ 31.521555] [<ffffff80088e1e20>]
ieee80211_sta_rx_queued_mgmt+0x190/0x698
[ 31.528239] [<ffffff80088bc44c>] ieee80211_iface_work+0x234/0x368
[ 31.535011] [<ffffff80080d81ac>] process_one_work+0x1cc/0x340
[ 31.541086] [<ffffff80080d8368>] worker_thread+0x48/0x430
[ 31.546814] [<ffffff80080de448>] kthread+0x108/0x138
[ 31.552195] [<ffffff8008082ec0>] ret_from_fork+0x10/0x50
In order to ensure that the "sta" remains alive (and consistent) for the
duration of bss_info_changed() mutual exclusion has to be ensured with
sta_remove().
This is done by introducing a mutex to cover firmware configuration
changes, which is made to also ensure mutual exclusion between other
operations changing the state or configuration of the firmware. With
this we can drop the rcu read lock.
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Each time we get disconnected from AP we get flooded with messages like:
...
ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
<until ratelimit kicks in>
ath10k_warn: 155 callbacks suppressed
...
Use ath10k_dbg() here too.
Signed-off-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The SMPTE-2084 transfer functions maps to the luminance range of
0-10000 cd/m^2. Other transfer functions use the traditional range of
0-100 cd/m^2.
I didn't take this into account so the luminance was off by a factor of
100.
Since qv4l2 made the same mistake in reverse I never noticed this until
I tested with actual SMPTE-2084 video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In case of SSI0 playback, SSI1 capture, SSI0 might be shared for
clock output if clock master mode.
Current rsnd driver had been assumed that SSI clock contiguous
output which is needed for SSI parent needs SSICR::EN (SSI module
enable) bit.
But, this bit controls data input/output, not for clock.
Clock contiguous output needs SSICR : FORCE, SCKD, SWSD,
and SSIWSR : CONT. Not SSICR : EN.
Because of this wrong assumption, and insufficient control, on current
code, for example, if it starts SSI0(playback) -> SSI1(capture) order,
SSI0 SSICR::EN bit will temporarily be 0.
It causes playback side underrun error. This is bug.
We can reproduce this issue with SSI+SRC (without DVC), and capture
during playback operation.
This patch fixup current (wrong) assumption, and control SSICR::EN bit
correctly.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For example SSI0/SSI1 case, SSI1 can share pin with SSI0.
And then, SSI1 needs SSI0's clock.
This clock controlling is very picky and difficult to understand
in current code.
This patch adds new rsnd_ssi_can_output_clk() macro,
the code will be more understandable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it the same style as other functions
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As suggested in reviews the requirement of clocks in the 'sound' node
is dropped and instead a leaf clock is used to configure frequency
of the audio root clock PLL. This can work now after the clock tree
definitions have been updated to allow clock rate setting propagation
on the path from the I2S controller up to the EPLL.
This patch also lowers the CODEC master clock frequency so as
to not exceed the maximum allowed 60 MHz at maximum audio sampling
rates.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The on-chip SRAM of i.MX6S is only 128 KiB. 4 KiB of that are allocated
for suspend to RAM since commit df595746fa ("ARM: imx: add suspend in
ocram support for i.mx6q"). Reduce the requested IRAM size to 124 KiB to
avoid an allocation failure that causes the coda driver to not use the
SRAM at all.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
coda_command_sync calls coda_command_async, which writes the
bit_stream_param context variable into the BIT_STREAM_PARAM register,
overwriting the previously set value during coda_start_decoding. Instead
of writing to the register, set bit_stream_param to ensure that the
decoder sequence init command is executed with the escape flag set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While looking at a compiler warning, I noticed the use of
IS_ERR_OR_NULL, which is generally a sign of a bad API design
and should be avoided.
In this driver, this is fairly easy, we can simply stop storing
error pointers in persistent structures, and change the two
functions that might return either a NULL pointer or an error
code to consistently return error pointers when failing.
of_parse_subdev() now separates the error code and the pointer
it looks up, to clarify the interface. There are two cases
where this function originally returns 'NULL', and I have
changed that to '0' for success to keep the current behavior,
though returning an error would also make sense there.
Fixes: e130291212 ("[media] media: Add i.MX media core driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
