The chipid macro/variable and regmap_read function call is not needed
because the TPS65219_REG_TI_DEV_ID register value is not a consistent value
across TPS65219 PMIC config versions. Reading from the DEV_ID register
without a consistent value to compare it to isn't useful. There isn't a
way to verify the match data ID is the same ID read from the DEV_ID device
register. 0xF0 isn't a DEV_ID value consistent across TPS65219 NVM
configurations.
For TPS65215, there is a consistent value in bits 5-0 of the DEV_ID
register. However, there are other error checks in place within probe()
that apply to both PMICs rather than keeping this isolated check for one
PMIC.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20250206173725.386720-4-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
- TPS65214 is a Power Management IC with 3 Buck regulators and 2 LDOs.
- TPS65214 has 2 LDOS and 1 GPO, whereas TPS65219 has 4 LDOs and 2 GPOs.
- TPS65214's LDO1 maps to TPS65219's LDO3.
- A key difference between TPS65215 & TPS65214 are the LDO current and
voltage output ranges and the configurable options available.
- The remaining features for both devices are the same.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250206173725.386720-3-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
TPS65215 is a Power Management IC with 3 Buck regulators and 2 LDOs.
TPS65215 has 2 LDOS and 1 GPO, whereas TPS65219 has 4 LDOs and 2 GPOs. The
remaining features for both devices are the same.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250206173725.386720-2-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
Convert mcu-mpc8349emitx.txt to YAML and list the compatible strings
currently in use.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250126-ppcyaml-v1-4-50649f51c3dd@posteo.net
Signed-off-by: Lee Jones <lee@kernel.org>
The ACPI ID table is defined globally without an #ifdef check for CONFIG_ACPI,
so ACPI_PTR() makes no sense here. Also note, driver depends on ACPI anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250205122536.631252-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
LAN969x uses the AT91 USART IP so make it selectable for ARCH_LAN969X.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20250131171739.1044701-2-robert.marko@sartura.hr
Signed-off-by: Lee Jones <lee@kernel.org>
REGCACHE_NONE is the default type of the cache when not provided.
Drop unneeded explicit assignment to it.
Note, it's defined to 0, and if ever be redefined, it will break
literally a lot of the drivers, so it very unlikely to happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250129152828.1802315-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
REGCACHE_NONE is the default type of the cache when not provided.
Drop unneeded explicit assignment to it.
Note, it's defined to 0, and if ever be redefined, it will break
literally a lot of the drivers, so it very unlikely to happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250129152823.1802273-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
If offset end up being high enough, right hand expression in functions
like sm501_gpio_set() shifted left for that number of bits, may
not fit in int type.
Just in case, fix that by using BIT() both as an option safe from
overflow issues and to make this step look similar to other gpio
drivers.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: f61be273d3 ("sm501: add gpiolib support")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20250115171206.20308-1-n.zhandarovich@fintech.ru
Signed-off-by: Lee Jones <lee@kernel.org>
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114192538.911970-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for STM32MP25 SoC. Use newly introduced compatible, to handle
new features.
Identification and hardware configuration registers allow to read the
timer version and capabilities (counter width, number of channels...).
So, rework the probe to avoid touching ARR register by simply read the
counter width when available. This may avoid messing with a possibly
running timer.
Also add useful bit fields to stm32-timers header file.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250110091922.980627-3-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add a new stm32mp25 compatible to stm32-timer dt-bindings in order to
support the STM32MP25 SoC. Some features has been added or updated in
the stm32-timer timer such as:
- hardware configuration and identification registers to read the timer
version and capabilities (counter width, number of channels...)
- dithering mode (can be used to extend PWM resolution)
- input triggers list
- new counter modes
- various bit-field updates
- power-domains property
Timer trigger identifier can be up to 19 (from timer 20)
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20250110091922.980627-2-fabrice.gasnier@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add compatible string "fsl,imx94-flexcan" for the i.MX94 chip, which
is backward compatible with i.MX95. Set it to fall back to
"fsl,imx95-flexcan".
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250307190816.2971810-1-Frank.Li@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----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=MOcN
-----END PGP SIGNATURE-----
Merge tag 'leds-fixes-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED fix from Lee Jones:
- Fix NULL pointer in STMicroelectronics LED1202 LED support
* tag 'leds-fixes-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds:
leds: leds-st1202: Fix NULL pointer access on race condition
Biju Das <biju.das.jz@bp.renesas.com> says:
This patch series addresses 2 issues
1) Fix typo in pattern properties for R-Car V4M.
2) Fix page entries in the AFL list.
v2->v3:
* Collected tags.
* Dropped unused variables cfg and start from
rcar_canfd_configure_afl_rules().
* Link to v2: https://lore.kernel.org/all/20250220094516.126598-1-biju.das.jz@bp.renesas.com
v1->v2:
* Split fixes patches as separate series.
* Added Rb tag from Geert for binding patch.
* Added the tag Cc:stable@vger.kernel.org
Link: https://patch.msgid.link/20250307170330.173425-1-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There are a total of 96 AFL pages and each page has 16 entries with
registers CFDGAFLIDr, CFDGAFLMr, CFDGAFLP0r, CFDGAFLP1r holding
the rule entries (r = 0..15).
Currently, RCANFD_GAFL* macros use a start variable to find AFL entries,
which is incorrect as the testing on RZ/G3E shows ch1 and ch4
gets a start value of 0 and the register contents are overwritten.
Fix this issue by using rule_entry corresponding to the channel
to find the page entries in the AFL list.
Fixes: dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250307170330.173425-3-biju.das.jz@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 7fdaf8966a ("can: ucan: use strscpy() to instead of strncpy()")
unintentionally introduced a one byte out of bound read on strscpy()'s
source argument (which is kind of ironic knowing that strscpy() is meant
to be a more secure alternative :)).
Let's consider below buffers:
dest[len + 1]; /* will be NUL terminated */
src[len]; /* may not be NUL terminated */
When doing:
strncpy(dest, src, len);
dest[len] = '\0';
strncpy() will read up to len bytes from src.
On the other hand:
strscpy(dest, src, len + 1);
will read up to len + 1 bytes from src, that is to say, an out of bound
read of one byte will occur on src if it is not NUL terminated. Note
that the src[len] byte is never copied, but strscpy() still needs to
read it to check whether a truncation occurred or not.
This exact pattern happened in ucan.
The root cause is that the source is not NUL terminated. Instead of
doing a copy in a local buffer, directly NUL terminate it as soon as
usb_control_msg() returns. With this, the local firmware_str[] variable
can be removed.
On top of this do a couple refactors:
- ucan_ctl_payload->raw is only used for the firmware string, so
rename it to ucan_ctl_payload->fw_str and change its type from u8 to
char.
- ucan_device_request_in() is only used to retrieve the firmware
string, so rename it to ucan_get_fw_str() and refactor it to make it
directly handle all the string termination logic.
Reported-by: syzbot+d7d8c418e8317899e88c@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-can/67b323a4.050a0220.173698.002b.GAE@google.com/
Fixes: 7fdaf8966a ("can: ucan: use strscpy() to instead of strncpy()")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250218143515.627682-2-mailhol.vincent@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently the flexcan driver does only support adding PHYs by using the
"old" regulator bindings. Add support for CAN transceivers as a PHY. Add
the capability to ensure that the PHY is in operational state when the link
is set to an "up" state.
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://patch.msgid.link/20250312-flexcan-add-transceiver-caps-v4-2-29e89ae0225a@liebherr.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently the flexcan driver does only support adding PHYs by using the
"old" regulator bindings. Add support for CAN transceivers as a PHY.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://patch.msgid.link/20250312-flexcan-add-transceiver-caps-v4-1-29e89ae0225a@liebherr.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
edid-decode gained recently support to check that infoframes are
compliant and match the EDID the monitor exposes.
Since the HDMI helpers provide those infoframes in debugfs, it makes it
easy to check from userspace that the drivers (and helpers) behave
properly.
Let's document it.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20250312-drm-hdmi-state-docs-v2-2-6352a5d68d5b@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
cdns3-plat can know if power was lost across system-wide suspend.
Forward that information:
- Grab the lost_power bool from cdns_role_driver::resume(). Store it
into the power_lost field in struct xhci_plat_priv.
- xhci-plat will call xhci_resume() with that value (ORed to whether we
are in a hibernation restore).
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-9-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that xhci_resume() exposes a power_lost boolean argument, expose
that to all xhci-plat implementations. They are free to set it from
wherever they want:
- Their own resume() callback.
- The xhci_plat_priv::resume_quirk() callback.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-8-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous signature was:
int xhci_resume(struct xhci_hcd *xhci, pm_message_t msg);
Internally, it extracted two information out of the message:
- whether we are after hibernation: msg.event == PM_EVENT_RESTORE,
- whether this is an auto resume: msg.event == PM_EVENT_AUTO_RESUME.
First bulletpoint is somewhat wrong: driver wants to know if the device
did lose power, it doesn't care about hibernation per se. Knowing that,
refactor to ask upper layers the right questions: (1) "did we lose
power?" and, (2) "is this an auto resume?". Change the signature to:
int xhci_resume(struct xhci_hcd *xhci, bool power_lost,
bool is_auto_resume);
The goal is to allow some upper layers (cdns3-plat) to tell us when
power was lost after system-wise suspend.
Note that lost_power is ORed at the start of xhci_resume() to
xhci->quirks & XHCI_RESET_ON_RESUME || xhci->broken_suspend. It is
simpler to keep those checks inside of xhci_resume() instead of doing
them at each caller of xhci_resume().
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-7-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At runtime_resume(), read the W1 (Wrapper Register 1) register to detect
if an hardware reset occurred. If it did, run the hardware init sequence.
This callback will be called at system-wide resume. Previously, if a
reset occurred during suspend, we would crash. The wrapper config had
not been written, leading to invalid register accesses inside cdns3.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-6-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device probe function mixes management code and hardware
initialisation code. Extract the latter into an explicitly named
cdns_ti_reset_and_init_hw() function to clarify intent. It also will
allow easier transition to using runtime PM for triggering HW init.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-5-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cdns_role_driver->resume() callback takes a second boolean argument
named `hibernated` in its implementations. This is mistaken; the only
potential caller is:
int cdns_resume(struct cdns *cdns)
{
/* ... */
if (cdns->roles[cdns->role]->resume)
cdns->roles[cdns->role]->resume(cdns, cdns_power_is_lost(cdns));
return 0;
}
The argument can be true in cases outside of return from hibernation.
Reflect the true meaning by renaming both arguments to `lost_power`.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-3-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unify naming convention: use `is_auto_runtime` in xhci-tegra, to be in
phase with (future) drivers/usb/host/xhci.c.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-2-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compatible "marvell,armada3700-xhci" match data uses the
struct xhci_plat_priv::init_quirk() function pointer to add
XHCI_RESET_ON_RESUME as quirk on XHCI.
Instead, use the struct xhci_plat_priv::quirks field.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://lore.kernel.org/r/20250205-s2r-cdns-v7-1-13658a271c3c@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a revert of
commit 04fb365c45 ("usb: dwc3: replace %p with %pK")
When the formatting was changed from %p to %pK that was a security
improvement, as %p would leak raw pointer values to the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
On the other hand, restricted pointers ("%pK") were never meant to be used
through printk(). They can unintentionally still leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch back to regular %p again.
Link: https://lore.kernel.org/lkml/20250113171731-dc10e3c1-da64-4af0-b767-7c7070468023@linutronix.de/
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://lore.kernel.org/r/20250310-restricted-pointers-usb-v2-2-a7598e2d47d1@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a revert of
commit 2f964780c0 ("USB: core: replace %p with %pK").
When the formatting was changed from %p to %pK that was a security
improvement, as %p would leak raw pointer values to the kernel log.
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
On the other hand, restricted pointers ("%pK") were never meant to be used
through printk(). They can unintentionally still leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch back to regular %p again.
Link: https://lore.kernel.org/lkml/20250113171731-dc10e3c1-da64-4af0-b767-7c7070468023@linutronix.de/
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://lore.kernel.org/r/20250310-restricted-pointers-usb-v2-1-a7598e2d47d1@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable d->name, returned by devm_kasprintf(), could be NULL.
A pointer check is added to prevent potential NULL pointer dereference.
This is similar to the fix in commit 3027e7b15b
("ice: Fix some null pointer dereference issues in ice_ptp.c").
This issue is found by our static analysis tool
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Link: https://lore.kernel.org/r/20250311012705.1233829-1-chenyuan0y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It makes sense that ARRAY_SIZE(prop) should == ARRAY_SIZE(prop-names),
so allow that to happen with interrupts.
Fixes bogus warnings such as:
usb@c2f8800: interrupt-names: ['pwr_event', 'qusb2_phy', 'hs_phy_irq'] is too short
Fixes: 53c6d854be ("dt-bindings: usb: dwc3: Clean up hs_phy_irq in binding")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250308-topic-dt_bindings_fixes_usb-v2-1-3169a3394d5b@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A subtle error got introduced while manually fixing merge conflict in
tcpm.c for commit 85c4efbe60 ("Merge v6.12-rc6 into usb-next"). As a
result of this error, the next state is unconditionally set to
SNK_WAIT_CAPABILITIES_TIMEOUT while handling SNK_WAIT_CAPABILITIES state
in run_state_machine(...).
Fix this by setting new state of TCPM state machine to `upcoming_state`
(that is set to different values based on conditions).
Cc: stable@vger.kernel.org
Fixes: 85c4efbe60 ("Merge v6.12-rc6 into usb-next")
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250310-fix-snk-wait-timeout-v6-14-rc6-v1-1-5db14475798f@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lis3lv02d driver does not need to create a platform device, it only
did so because it was simple to do that in order to get a place in sysfs
to hang some device-specific attributes. Change it over to use the faux
device instead as this is NOT a real platform device, and it makes the
code even smaller than before.
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/2025021028-shortcake-stained-b0a8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tlclk driver does not need to create a platform device, it only did
so because it was simple to do that in order to get a place in sysfs to
hang some device-specific attributes. Change it over to use the faux
device instead as this is NOT a real platform device, and it makes the
code even smaller than before.
Cc: Mark Gross <markgross@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/2025021028-askew-smashing-4ff9@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dummy regulator driver does not need to create a platform device, it
only did so because it was simple to do. Change it over to use the
faux bus instead as this is NOT a real platform device, and it makes
the code even smaller than before.
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/2025021027-outclass-stress-59dd@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Count the pages used by pKVM for the guest stage-2 in memory stats under
secondary pagetable, similarly to what the VHE mode does.
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250313114038.1502357-4-vdonnefort@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
In order to account for memory dedicated to the stage-2 page-tables, use
a separated memcache when tearing down the VM. Meanwhile rename
reclaim_guest_pages to reflect the fact it only reclaim page-table
pages.
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250313114038.1502357-3-vdonnefort@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Add flags to kvm_hyp_memcache and propagate the latter to the allocation
and free callbacks. This will later allow to account for memory, based
on the memcache configuration.
Signed-off-by: Vincent Donnefort <vdonnefort@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250313114038.1502357-2-vdonnefort@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
A fix to resolve a timeout error during counter enable leading to a
false report of 'enable' state in stm32-lptimer-cnt. A fix to properly
intialize counter channels during probe to avoid operating under an
undefined state in microchip-tcb-capture.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSNN83d4NIlKPjon7a1SFbKvhIjKwUCZ8rBeAAKCRC1SFbKvhIj
K4VkAQD4z7j/DomyhavS17wBI5qk4Ihgo3uBFXnpRNRcsCinQgEAyZHPnizwpPBF
YVp9F3iOrs2tICHef5iRcDG13ZtavgA=
=l93F
-----END PGP SIGNATURE-----
Merge tag 'counter-fixes-for-6.14' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wbg/counter into char-misc-linus
William writes:
Counter fixes for 6.14
A fix to resolve a timeout error during counter enable leading to a
false report of 'enable' state in stm32-lptimer-cnt. A fix to properly
intialize counter channels during probe to avoid operating under an
undefined state in microchip-tcb-capture.
* tag 'counter-fixes-for-6.14' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wbg/counter:
counter: microchip-tcb-capture: Fix undefined counter channel state on probe
counter: stm32-lptimer-cnt: fix error handling when enabling
- Peter's change updates his email address.
- Kuhanh's change increases timeout for altera-cvp driver
- Arnd's change removes incorrect of_match_ptr
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-next branch).
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
-----BEGIN PGP SIGNATURE-----
iIkEABYIADEWIQSgSJpClIeaArXyudb8twOBpKCM2gUCZ8+SqRMceWlsdW4ueHVA
aW50ZWwuY29tAAoJEPy3A4GkoIzaxGMBAMMH2vqgAFXxVE7pd7sS8rIV8x/+QVSm
laJLfIMNjFzxAQC0gZ8OBX/NZ+7CRifTzGo6UOZMj4LGP7zaeTdXGTcyAQ==
=3lOl
-----END PGP SIGNATURE-----
Merge tag 'fpga-for-6.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-next
Xu writes:
FPGA Manager changes for 6.15-rc1
- Peter's change updates his email address.
- Kuhanh's change increases timeout for altera-cvp driver
- Arnd's change removes incorrect of_match_ptr
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-next branch).
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
* tag 'fpga-for-6.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: versal: remove incorrect of_match_ptr annotation
fpga: altera-cvp: Increase credit timeout
fpga: m10bmc-sec: update email address for Peter Colberg
========
- Remove unused mhi_device_get() and mhi_queue_dma() APIs.
- Add support for SA8775p MHI endpoint device with IP_SW0 channel.
- Fix the race between mhi_unprepare_from_transfer() and mhi_queue_buf().
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZ6VDKoFIy9ikWCeXVZ8R5v6RzvUFAmfTxYsACgkQVZ8R5v6R
zvUewgf/TYKTmhzkeV4KVJ8CLqVw2Ha1HJTJ/zYf2JmcfgapGW8fMktPSE/q38vJ
4p/GhrY+4eLAoFdMF5Utmo6xGSvvf81sPu7DYXNA1J1VQa7D5eHx4uKiwp9ctngE
vNNRZKEkdq7mo9Lz5opUNs/bDmll8KMjgUumGl3BIF6HUV6kZGC1Qhuc6ovfxAkP
CpCO7AvgUeIoE3Iw+kjuOlp5tcPxdvYMyGibs1m+FlxOnYQQrj9lUyVamVHaDJX3
m9xVFj+sK0k+xdcyG3+mBISpSI1aen3pezpqkpoUfOfZVF7A68jXr+ba/1wdmz1b
ydqa/aXTy1rXva/u+felsoj6SujjwA==
=p40V
-----END PGP SIGNATURE-----
Merge tag 'mhi-for-v6.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next
Manivannan writes:
MHI Host
========
- Remove unused mhi_device_get() and mhi_queue_dma() APIs.
- Add support for SA8775p MHI endpoint device with IP_SW0 channel.
- Fix the race between mhi_unprepare_from_transfer() and mhi_queue_buf().
* tag 'mhi-for-v6.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: host: Fix race between unprepare and queue_buf
bus: mhi: host: pci_generic: Add support for SA8775P endpoint
bus: mhi: host: Remove unused functions
