Karan Tilak Kumar <kartilak@cisco.com> says:
Hi Martin, reviewers,
This cover letter describes the feature: add support for Fabric
Discovery and Login Services (FDLS) to fnic driver.
This functionality is needed to support port channel RSCN (PC-RSCN)
handling and serves as a base to create FC-NVME initiators
(planned later), and eCPU handling (planned later).
It is used to discover the fabric and target ports associated with the
fabric. It will then login to the target ports that are zoned to it.
The driver uses the tport structure presented by FDLS.
Port channel RSCN is a Cisco vendor specific RSCN event. It is
applicable only to Cisco UCS fabrics.
In cases where the eCPU in the UCS VIC (Unified Computing Services
Virtual Interface Card) hangs, a fabric log out is sent to the fabric.
Upon successful log out from the fabric, the IO path is failed over to
a new path.
Generally from a feature perspective, the code is divided into adding
support for this functionality initially. Then, code has been added to
modify the IO path and interfaces. Finally, support for port channel
RSCN handling has been added.
Here are the headers of some of the salient patches:
o add headers and definitions for FDLS
o add support for fabric based solicited requests and responses
o add support for target based solicited requests and responses
o add support for unsolicited requests and responses
o add support for FDMI
o add support for FIP
o add functionality in fnic to support FDLS
o modify IO path to use FDLS and tport
o modify fnic interfaces to use FDLS
o add support to handle port channel RSCN
Even though the patches have been made into a series, some patches are
heavier than others. But, every effort has been made to keep the
purpose of each patch as a single-purpose, and to compile cleanly.
All the individual patches compile cleanly. The compiler used is GCC
13.3. Some function calls have been coded as placeholders with
appropriate comments to avoid compiler warnings.
This patchset has been tested as a whole. Therefore, the tested-by
fields have been added only to one patch in the set. I've refrained
from adding tested-by to most of the patches, so as to not mislead the
reviewer/reader.
A brief note on the unit tests:
o. Perform zone in zone out testing in a loop: remove a target
port from the zone, add it to the zone in a loop. 1000+ iterations
of this test have been successful.
o. Configure multipathing, and run link flaps on single link.
IOs drop briefly, but pick up as expected.
o. Configure multipathing, and run link flaps on two links, with a
30 second delay in between. IOs drop briefly, but pick up as expected.
o. Module load/unload test.
o. Repeat the above tests with 1 queue and 64 queues.
All tests were successful.
Please consider this patch series for the next merge window.
Link: https://lore.kernel.org/r/20241212020312.4786-1-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge series from Shengjiu Wang <shengjiu.wang@nxp.com>:
On i.MX943, the FIFO data address is changed and the bit width
of CICOSR is changed.
Add a new compatible string and update driver for these changes.
The yt2_1380_fc_serdev_probe() function calls devm_serdev_device_open()
before setting the client ops via serdev_device_set_client_ops(). This
ordering can trigger a NULL pointer dereference in the serdev controller's
receive_buf handler, as it assumes serdev->ops is valid when
SERPORT_ACTIVE is set.
This is similar to the issue fixed in commit 5e700b384e
("platform/chrome: cros_ec_uart: properly fix race condition") where
devm_serdev_device_open() was called before fully initializing the
device.
Fix the race by ensuring client ops are set before enabling the port via
devm_serdev_device_open().
Note, serdev_device_set_baudrate() and serdev_device_set_flow_control()
calls should be after the devm_serdev_device_open() call.
Fixes: b2ed33e8d4 ("platform/x86: Add lenovo-yoga-tab2-pro-1380-fastcharger driver")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250111180951.2277757-1-chenyuan0y@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The dell_uart_bl_serdev_probe() function calls devm_serdev_device_open()
before setting the client ops via serdev_device_set_client_ops(). This
ordering can trigger a NULL pointer dereference in the serdev controller's
receive_buf handler, as it assumes serdev->ops is valid when
SERPORT_ACTIVE is set.
This is similar to the issue fixed in commit 5e700b384e
("platform/chrome: cros_ec_uart: properly fix race condition") where
devm_serdev_device_open() was called before fully initializing the
device.
Fix the race by ensuring client ops are set before enabling the port via
devm_serdev_device_open().
Note, serdev_device_set_baudrate() and serdev_device_set_flow_control()
calls should be after the devm_serdev_device_open() call.
Fixes: 484bae9e4d ("platform/x86: Add new Dell UART backlight driver")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250111180118.2274516-1-chenyuan0y@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
msm is automagically upgrading normal commits to full modesets, and
that's a big no-no:
- for one this results in full on->off->on transitions on all these
crtc, at least if you're using the usual helpers. Which seems to be
the case, and is breaking uapi
- further even if the ctm change itself would not result in flicker,
this can hide modesets for other reasons. Which again breaks the
uapi
v2: I forgot the case of adding unrelated crtc state. Add that case
and link to the existing kerneldoc explainers. This has come up in an
irc discussion with Manasi and Ville about intel's bigjoiner mode.
Also cc everyone involved in the msm irc discussion, more people
joined after I sent out v1.
v3: Wording polish from Pekka and Thomas
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Pekka Paalanen <pekka.paalanen@collabora.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Simon Ser <contact@emersion.fr>
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Simona Vetter <simona.vetter@intel.com>
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20250108172417.160831-1-simona.vetter@ffwll.ch
This commit enables the cleaner shader feature for GFX12.0 and GFX12.0.1
GPUs. The cleaner shader is important for clearing GPU resources such as
Local Data Share (LDS), Vector General Purpose Registers (VGPRs), and
Scalar General Purpose Registers (SGPRs) between workloads.
- This feature ensures that GPU resources are reset between workloads,
preventing data leaks and ensuring accurate computation.
By enabling the cleaner shader, this update enhances the security and
reliability of GPU operations on GFX12.0 hardware.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark options only meant to be used for debugging as unsafe so that the
kernel is tainted when they are used.
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That is needed to enforce isolation between contexts.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We sometimes have people trying to use debugging options in production
environments.
Mark options only meant to be used for debugging as unsafe so that the
kernel is tainted when they are used.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <felix.kuehling@amd.com>
Acked-by: Simona Vetter <simona.vetter@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lets use the existing helper instead of peeking into the structure
directly.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable gfxoff with the compute workload on gfx12. This is a
workaround for the opencl test failure.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The device full name is embedded trace extension. There is no good fit
in generic names list for the embedded trace extension. ETE is abbreviation
of embedded trace extension and the number is the CPU number that ete is
associated. Change the pattern of the node name as it won't affect any
device tree node as of now.
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20250107090031.3319-2-quic_jinlmao@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
In the original change, rawmidi_info.tied_device showed -1 for the
unknown or untied device. But this would require the user-space to
check the protocol version and judge the value conditionally, which
is rather error-prone.
Instead, set the tied_device = 0 to be default as unknown, and
indicate the real device with the offset 1, for achieving more
backward compatibility.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Link: https://patch.msgid.link/20250114104711.19197-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a problem with bch_stripe that is going to take an on disk
format rev to fix - we can't access the block sector counts if the
checksum type is unknown.
Document it for now, there are a few other things to fix as well.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The transaction is going to abort, so there will be no cycle involving
this transaction anymore.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The function graph tracer now calculates the calltime internally and for
each instance. If there are two instances that are running function graph
tracer and are tracing the same functions, the timings of the length of
those functions may be slightly different:
# trace-cmd record -B foo -p function_graph -B bar -p function_graph sleep 5
# trace-cmd report
[..]
bar: sleep-981 [000] ...1. 1101.109027: funcgraph_entry: 0.764 us | mutex_unlock(); (ret=0xffff8abcc256c300)
foo: sleep-981 [000] ...1. 1101.109028: funcgraph_entry: 0.748 us | mutex_unlock(); (ret=0xffff8abcc256c300)
bar: sleep-981 [000] ..... 1101.109029: funcgraph_exit: 2.456 us | } (ret=0xffff8abcc256c300)
foo: sleep-981 [000] ..... 1101.109029: funcgraph_exit: 2.403 us | } (ret=0xffff8abcc256c300)
bar: sleep-981 [000] d..1. 1101.109031: funcgraph_entry: 0.844 us | fpregs_assert_state_consistent(); (ret=0x0)
foo: sleep-981 [000] d..1. 1101.109032: funcgraph_entry: 0.803 us | fpregs_assert_state_consistent(); (ret=0x0)
Link: https://lore.kernel.org/all/20250114101806.b2778cb01f34f5be9d23ad98@kernel.org/
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/20250114101202.02e7bc68@gandalf.local.home
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
When the cycle doesn't involve the initiator of the cycle detection,
we might choose a transaction that is not involved in the cycle to abort.
It shouldn't be that since it won't break the cycle, this patch
therefore chooses the transaction in the cycle to abort.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
This patch introduces a helper function called lock_graph_pop_from,
it pops the graph from i.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
If the transaction chose itself as a victim before and restarted, it
might request a no fail lock request this time. But it might be added to
others' lock graph and be chose as the victim again, it's no longer safe
without additional check. We can also convert the cycle detector to be
fully RCU-based to solve that unsoundness, but the latency added to trans_put
and additional memory required may not worth it.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
If the lock has been acquired and unlocked, we don't have to do clear
and wakeup again, though harmless since we hold the intent lock. Merge
the condition might be clearer.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
This reverts commit 62448afee7.
six_lock_tryupgrade fails only if there is an intent lock held,
it won't fail no matter how many read locks are held.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Changes to support DTR with spi-mem.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmeGgAIACgkQJNaLcl1U
h9CodQf9Eek9Usqn6GzjYI8MEAv5XfB0TjG/gleATAtc7Zk4R0Vwo4COnx2+5Fo/
03CV8yAt4Z0fjsD5mzWdnoiVNKCumpS+aFlzwVlOMq1KMYMH1AZAjqYeK9nHYpSn
U5lGse0C9DGrv2jb2KNA5yKGHL/ZquRyY4h0+CKG85jGpmpAWqBAcXaqXm02ts2Q
lTlymD0yefnatQ/0MrGj8bZF0q90Y7oTARDwMyh/MKMpPJslYI5AUT2USKT0qZsp
7sp9SpDE6gyoZy3q0sDXrmRKvMLpV5oLVN5amREnnokNeD9FAP8swDbNH48Fbrlm
4zE4CaHWv2mPSrcbBSJRZRNT/+Neqg==
=uA3v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmeGgF0ACgkQJNaLcl1U
h9Bv8Af7B7dNEcS10JtjACL/z0w87Zx3SXp0TIUl5K6k53n12hO8PUSptmu3ftdF
IK24jG41ju7LFUdL05XT9zMi9Z4HbcpJCQjVXXmZWNZGwgyUwhdKgSW6OgzwYLeM
qqeoZX4sPpbjLETw57GT0GU9hC7IMxyHUH/h6uNwFEbJi1Dt//Sh73nboEWYx5WO
CPlSHxFt4l1LjZFr5FMkoMdBFsCObF92bMou/xccb8bgVyfLye+KKLF8GaZ4pebk
hOW4nUcRux+XhiGFmqjyZ3KNssGoBOx8TF4TiQ3ik5lHBjB4i1SmRlkr/xwTFDvP
6f/GlhG5GwEVA6S7pGFqcj1614V0uw==
=IwJ4
-----END PGP SIGNATURE-----
spi-nand/spi-mem DTR support
Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:
Here is a (big) series supposed to bring DTR support in SPI-NAND.
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250111185400.183760-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
- Added a testcase to verify the multiroot force merge fini.
- Added a new field in_use to track the mm freed status.
v2:(Matthew)
- Add kunit_fail_current_test() when WARN_ON is true.
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Lin.Cao <lincao12@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241226070116.309290-2-Arunpravin.PaneerSelvam@amd.com
If buddy manager have more than one roots and each root have sub-block
need to be free. When drm_buddy_fini called, the first loop of
force_merge will merge and free all of the sub block of first root,
which offset is 0x0 and size is biggest(more than have of the mm size).
In subsequent force_merge rounds, if we use 0 as start and use remaining
mm size as end, the block of other roots will be skipped in
__force_merge function. It will cause the other roots can not be freed.
Solution: use roots' offset as the start could fix this issue.
Signed-off-by: Lin.Cao <lincao12@amd.com>
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241226070116.309290-1-Arunpravin.PaneerSelvam@amd.com
After commit e6204f39fe ("spi: amd: Drop redundant check"), clang warns (or
errors with CONFIG_WERROR=y):
drivers/spi/spi-amd.c:695:9: error: variable 'ret' is uninitialized when used here [-Werror,-Wuninitialized]
695 | return ret;
| ^~~
drivers/spi/spi-amd.c:673:9: note: initialize the variable 'ret' to silence this warning
673 | int ret;
| ^
| = 0
1 error generated.
ret is no longer set on anything other than the default switch path.
Replace ret with a direct return of 0 at the end of the function and
-EOPNOTSUPP in the default case to resolve the warning.
Fixes: e6204f39fe ("spi: amd: Drop redundant check")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501112315.ugYQ7Ce7-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250111-spi-amd-fix-uninitialized-ret-v1-1-c66ab9f6a23d@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The update of the residency values needs to be protected by a lock to
avoid multiple entrypoints, for example when multiple userspace clients
read the sysfs file. Other in-kernel clients are going to be added to
sample these values, making the problem worse. Protect those updates
with a raw_spinlock so it can be called by future integration with perf
pmu.
Suggested-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110173308.2412232-2-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Add a selftest creating three extents and then deleting two out of the
three extents.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Test creating a range of three RAID stripe-extents and then punch a hole
in the middle, deleting all of the middle extents and partially deleting
the "book ends".
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a selftest for punching a hole into a RAID stripe extent. The test
create an 1M extent and punches a 64k bytes long hole at offset of 32k from
the start of the extent.
Afterwards it verifies the start and length of both resulting new extents
"left" and "right" as well as the absence of the hole.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add a selftest for RAID stripe-tree deletion with a delete range spanning
two items, so that we're punching a hole into two adjacent RAID stripe
extents truncating the first and "moving" the second to the right.
The following diagram illustrates the operation:
|--- RAID Stripe Extent ---||--- RAID Stripe Extent ---|
|----- keep -----|--- drop ---|----- keep ----|
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The selftests for partially deleting the start or tail of RAID
stripe-extents split these extents in half.
This can hide errors in the calculation, so don't split the RAID
stripe-extents in half but delete the first or last 16K of the 64K
extents.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit 5e72aabc1f ("btrfs: return ENODATA in case RST lookup fails")
changed btrfs_get_raid_extent_offset()'s return value to ENODATA in case
the RAID stripe-tree lookup failed.
Adjust the test cases which check for absence of a given range to check
for ENODATA as return value in this case.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
If the stripe extent we want to delete starts before the range we want to
delete and ends after the range we want to delete we're punching a
hole in the stripe extent:
|--- RAID Stripe Extent ---|
| keep |--- drop ---| keep |
This means we need to a) truncate the existing item and b)
create a second item for the remaining range.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When a user requests the deletion of a range that spans multiple stripe
extents and btrfs_search_slot() returns us the second RAID stripe extent,
we need to pick the previous item and truncate it, if there's still a
range to delete left, move on to the next item.
The following diagram illustrates the operation:
|--- RAID Stripe Extent ---||--- RAID Stripe Extent ---|
|--- keep ---|--- drop ---|
While at it, comment the trivial case of a whole item delete as well.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Fix tail delete of RAID stripe-extents, if there is a range to be deleted
as well after the tail delete of the extent.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When deleting the front of a RAID stripe-extent the delete code
miscalculates the size on how much to pad the remaining extent part in the
front.
Fix the calculation so we're always having the sizes we expect.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When modifying a RAID stripe-extent, ASSERT() that the length of the new
RAID stripe-extent is always greater than 0.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Even if the RAID stripe-tree is not enabled in the filesystem,
do_free_extent_accounting() still calls into btrfs_delete_raid_extent().
Check if the extent in question is on a block-group that has a profile
which is used by RAID stripe-tree before attempting to delete a stripe
extent. Return early if it doesn't, otherwise we're doing a unnecessary
search.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
RAID stripe-tree is an incompatible feature not a read-only compatible, so
set the incompat flag not a compat_ro one in the selftest code.
Subsequent changes in btrfs_delete_raid_extent() will start checking for
this flag.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
