As the number of keymaps increases and is very unlikely to
reduce, this patch helps to reduce memory consumption by
declaring all keymaps as __initdata and copying right keymap
during DMI detection. On x86 this make the module size at
runtime going from 10616 to 9428: a bit more than 1kb saved.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It turns out that the keymaps in the wistron driver are almost the
same, the main difference being some keys which may not exist and
leds which might not be present. Therefore it's possible to write
a generic keymap which would allow the use of an unknown keyboard
with little drawbacks. The user can select it specifying the parameter
"keymap=generic".
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acerhk supports already a lot of laptops. Lets import its database so
that everyone can benefit of the work of Olaf Tauber. Only the "tm_new"
laptops were imported. "tm_old" laptops could be possible but requires
more testing and probably only few laptops are still alive. "dritek"
laptops should probably be imported into a different driver. Also compress
the keymaps by fitting each entry on an int. Most of the dmi matching was
written based on google searches, so it's rather prone to errors. That's
why I'm asking people to confirm it works.
Support to generate switch input events was added as some laptops indicate
lid open/close through this interface.
This adds the following hardware:
Acer TravelMate 370
Acer TravelMate 380
Acer TravelMate C300
Acer TravelMate C100
Acer TravelMate C110
Acer TravelMate 250
Acer TravelMate 350
Acer TravelMate 620
Acer TravelMate 630
Acer TravelMate 220
Acer TravelMate 230
Acer TravelMate 260
Acer TravelMate 280
Acer TravelMate 360
Acer TravelMate 2100
Acer TravelMate 2410
Acer Aspire 1500
Acer Aspire 1600
Acer Aspire 3020
Acer Aspire 5020
Medion MD 2900
Medion MD 40100
Medion MD 95400
Medion MD 96500
Fujitsu Siemens Amilo 7820
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are mice reporting to logitech's queries with model
of 0. Do not claim that these are Logitech mice.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Disable both keyboard and auxiliary interfaces before switching
to legacy mode to prevent atkbd from getting "empty" interrupts.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pete Zaitcev reports that with his touchpad, if he lifts the finger
and places it elsewhere, the pointer sometimes warps dramatically.
This happens because we don't store coordinates unless we detect a
touch so sometimes we have stale coordinates in queue (from where
the finger left the pad) and averaging makes cursor to jump across
the screen. The solution is to always store the latest coordinates.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Delete the never-compiled source file drivers/input/power.c, and
remove its entry from the corresponding Makefile, as there is no
Kconfig file that refers to the config option INPUT_POWER
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use printk_ratelimit() to protect ourselves from buggy drivers or
devices endlessly generating invalid events.
Suggested by Andrew Morton.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Encode synaptics model in psmouse->model so it will be
exported via sysfs as input_dev->id.version and become
visible for applications.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Using usb_unlink_urb can cause iforce_open to fail when called
soon after iforce_release. Also updated my email address and
replaced calls to printk() by dbg(), warn(), info(), err()...
Signed-off-by: Johann Deneux <johann.deneux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The naming convention in input handlers was very confusing -
client stuctures were called lists, regular lists were also
called lists making anyone looking at the code go mad.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- consolidate code for binding handlers to a device
- return error codes from handlers connect() methods back to input
core and log failures
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
(Reverted part which moved it from eh_abort_handler to eh_host_reset_handler)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
myri10ge: update driver version to 1.3.0-1.233
myri10ge: more Intel chipsets providing aligned PCIe completions
myri10ge: fix management of the firmware 4KB boundary crossing restriction
cxgb3 - missing CPL hanler and register setting.
cxgb3 - MAC watchdog update
cxgb3 - avoid deadlock with mac watchdog
skge: fix wake on lan
sky2: phy workarounds for Yukon EC-U A1
sky2: turn on clocks when doing resume
sky2: turn carrier off when down
skge: turn carrier off when down
[PATCH] bcm43xx: Fix PPC machine checks and match loopback gain specs
[PATCH] bcm43xx: Fix 802.11b/g scan limits to match regulatory reqs
[PATCH] zd1211rw: Fix E2P_PHY_REG patching
[PATCH] zd1211rw: Reject AL2230S devices
Noone should use kobj.name directly since it may contain garbage.
Objects with longer names have them stored in separately allocated
memory pointed to by kobj->k_name.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some situations we can receive the ORB status write before we
have received the ORB pointer write response. When this happens,
we assume that the fw_transaction is finished and free the ORB
struct containing the fw_transaction.
This fix make the status write logic only accept status writes
for ORBs where the initial ORB pointer write transaction finished.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Or the SAM status codes from the device sense data into the
command error code.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
the Nikon D80 camera will not work without an UNUSUAL_DEV entry embodied
in the attached patch (made against 2.6.20.3). Hope you find it helpful,
or if not, pass it along to someone who does.
From: Emil Larsson <emil@swip.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is one significant difference between the behavior of root hubs
(as embodied in host controller hardware) and external hubs: When a
remote-wakeup signal is received, an external hub sends an interrupt
message at the _end_ of the resume sequence but a root hub generates
and interrupt at the _beginning_ of the resume sequence. The host
system must poll for the end of the sequence.
When ehci-hcd was converted to interrupt-driven operation instead of
using polling, the remaining need for this particular poll was
overlooked. This patch (as894) fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bit setting was off by one.
Tested with RTC and GPIO_WKUP interrupts.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the Intel 5000 southbridge (aka Intel 6310/6311/6321ESB) PCIe ports
and the Intel E30x0 chipsets to the whitelist of aligned PCIe completion.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simpler way of dealing with the firmware 4KB boundary crossing
restriction for rx buffers. This fixes a variety of memory
corruption issues when using an "uncommon" MTU with a 16KB
page size.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove specific CPL handler.
Add missing CPL handler.
Add missing register setting when the interface is brought up.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The MAC watchdog was failing if the peer interface was brought down.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a deadlock when the interface s configured down and
the watchdog tack is sleeping on rtnl_lock.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to rework wake on lan code to setup properly and get activated
on shutdown (and suspend), not when ethtool is run.
This does not need to go to stable queue because wake on lan
was not even included in 2.6.20 (or earlier versions).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround Yukon EC-U wasn't comparing with correct
version and wasn't doing correct setup. Without it, 88e8056
throws all sorts of errors.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some of these chips are disabled until clock is enabled.
This fixes:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404107
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver needs to turn off carrier when down, otherwise it can
confuse bonding and bridging and looks like carrier is on immediately
when it is brought back up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some HID devices are looking on the unused bits in the HID reports they
receive. This is violating the specification, but we want to make those
devices work. Well-behaving devices are unaffected, as they don't care
about the unused bits.
If bitsused % 8 is 0 all bits in data[] get used and we don't need to
clear anything. Otherwise (bitsused % 8) bits of the last byte get used.
By shifting 1 for (bitsused % 8) bits and subtracting 1 we create a mask
consisting of (bitsused % 8) ones and remaining zeroes. By ANDing we
clear the upper unused bits.
Signed-off-by: Simon Budig <simon@budig.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds support for WiseGroup Quad Joypad (0x0925/0x8800). The
same quirks as for Dual Joypad (0x0925/0x8866) are needed.
Signed-off-by: Sam Liddicott <sam@liddicott.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for Logitech Force 3D Pro Joystick (0x046d/0xc286)
to hid-lgff driver.
Device ID reported by Richard Bolkey <rbolkey@cs.utexas.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On Dell W7658 keyboard, when BIOS sets NumLock LED on, it survives the
takeover by kernel and thus confuses users.
Eating of an increasibly scarce quirk bit is unfortunate. We do it for safety,
given the history of nervous input devices which crash if anything unusual
happens.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech MX3000 contains report descriptor which doesn't cover usages
above 0x28c, but emits such usages. Report descriptor needs fixing
in the very same way as with receivers shipped with S510 keyboards.
This patch also adds a few mappings for multimedia keys that S510 didn't
emit.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech S510 keyboard is shipped with USB receivers with various product
ids, all need their report descriptor to be fixed. This adds PID 0xc50c.
Reported by Christophe Colombier in kernel.org bugzilla #7352
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add HID_QUIRK_HIDDEV for the Belkin Flip USB KVM, which provides for software
control of switching via a HID class interface. It overloads three HID LED
usages, two of which aren't mapped in the ev_dev input subsection, and which it
doesn't make sense to map. In order to force the creation of a hiddev device
for controlling the Flip, this quirk flag is needed.
Signed-off-by: Daniel P. Engel <dengel@sourceharvest.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
