Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Fixed: 12bit precision is lost at suspend/resume
- Updated: use pm_dev_ops
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In S5PV210/S5PC110/EXYNOS4, ADCMUX channel selection uses ADCMUX
register, not ADCCON register. This patch corrects the behavior of
SAMSUNG-ADC for such CPUs.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch allows the Samsung ADC driver to enable VDD regulator
at probe and resume and to disable at exit and suspend.
In a platform where ADC's VDD regulator is not "always-on", this
control is required although this patch does not provide fine-grained
power control (turning on the regulator only when being accessed).
However, if VDD regulator ("vdd" for the adc device) is not provided,
the regulator control will not be activated because there are platforms
that do not provide regulator for ADC device.
arch_initcall has been modified to module_init in order to allow
regulators to be available at probe.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The PLL restore routine supports waiting pll locking. If PLL is
enabled in restoring sequence, it should wait until PLL is locked.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds save/restore values for Power Control Register and
Diagnostic Register for PM.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
We need to balance between set and check S5P_CENTRAL_SEQ_CONFIGURATION
register in syscore_ops suspend/resume function when failure in enter
suspend mode. Moved this register setting for PM for the purpose of balancing.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since early wakeup can be handled in pm so we don't need masking
interrupts of external GIC. When the early wakeup interrupt happens,
PMU(Power Management Unit) ignores WFI instruction. This means that
PC(Program Counter) passed without any changes. This patch can handle
that case by early wakeup interrupt.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
[kgene.kim@samsung.com: fixed return of exynos4_cpu_suspend()]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
PMU(Power Management Unit) configuraion for S2RAM(SLEEP) is removed
and using function which provided by PMU support code to configure
PMU register.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
EXYNOS4 supports 3 different system level power down mode by PMU (Power
Management Unit). Each power down mode need to configure many PMU registers
with different value. This patch supports function to configure PMU registers
with pre-defined values in PMU code. This function may be used by PM code and
AFTR/LPA support driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds spdif to the machine supported device list for
SMDKV310.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To insert the code for power on/off with pmu control to support hotplug in/out core1
As for hotplug.c, the codes for core1 to be hotplug in/out is inserted.
As for regs-pmu.h, S5P_CORE_LOCAL_PWR_EN is defined.
As for platsmp.c, the codes for core1 to be powered on is inserted.
Signed-off-by: JungHi Min <junghi.min@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds chained IRQ enter/exit functions to uart
interrupt handler in order to function correctly on primary
controllers with different methods of flow control.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
External GIC cannot support PPI (Private Peripheral Interrupt) for
ARM private timers. Thus MCT should be selected as clock event timers
by default.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
For full support of power modes, this patch adds implementation
external GIC on EXYNOS4.
External GIC of Exynos4 cannot support register banking so
several interrupt related code for CPU1 should be different
from that of CPU0.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since Samsung EXYNOS4210 cannot support register banking in GIC,
so needs to update CPU interface base address.
The 'gic_chip_data' is used for it, this patch moves gic_chip_data
structure declaraton to arch/arm/include/asm/hardware/gic.h to use
it.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
IRQ_MCT_L1 is connected directly to GIC in external GIC mapping,
while in internal GIC mapping, it is connected to GIC through
interrupt combiner. Therfore the affinity for mct1 event timer
interrupt should be changed through IRQ_MCT_L1.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
To support external GIC needs to update mapping of interrupt number.
This patch modifies it for external GIC and accordingly removes
the unused code.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds external GIC io memory mapping
to support external GIC on EXYNOS4.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds device definition to enable SATA on SMDKV310
Signed-off-by: Inderpal Singh <inderpal.s@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definitions to enable support for qt602240 touch screen
driver for Universal C210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definitions to enable support for MCS Touchkey driver
for Universal C210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definitions to enable support for s5p-fimc driver for
Universal C210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Basically, the SAMSUNG_DEV_PWM is required to use s5p-time.c for HRT.
Reported-by: Marek Szyprowski<m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch "ARM: SAMSUNG: Add support for pre-sleep/post-restore gpio
control" broke compilation on Exynos4 platform with power management
enabled. This patch adds missing stubs that fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a callback so that per-arch can do pre-sleep and post-resume
gpio configuration so that for the S3C64XX, the GPIO configuration
is restored before the sleep mode is cleared.
For the S3C64XX case, it means that the GPIOs get set back to normal
operation after the restore code puts the original configurations
back in after the
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Any interrupts based off either of the onboard VICs cannot be resumed
from any more as it seems set_irq_wake() is now checking the error code
returned from the low level handlers and not setting the wake-state on
the interrupt if this fails.
Ensure that we make the interrupts we can resume from available on the
VIC and then do a pre-sleep mask of all the VIC interrupts as the wakeup
is handled by a seperate block.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The struct clk definition for Samsung platforms is extended to include
a instance of struct clk_lookup and a device name. When clocks are
registered using s3c24xx_register_clock function, the dev_id, con_id
and clk members are initialized with information from the struct clk
instance and struct clk_lookup member is registered.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Bus number 4 doesn't exist in the mainline kernel. The device is
attached to bus number 3. (In the ChromeOS kernel, one of the I2C
busses is split in two with a mux, this pushing all later busses
to a higher bus number. In this case, 4 is the correct bus number
for the ADT7461).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DAP3 is used for a bunch of GPIOs. Not tri-stating the pins means audio
signals get sent out there, and this ends up resetting USB and breaking
SDHCI too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently using just long but this is not enough for the LPAE format
(64-bit entries).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the documented kernel entry requirements are not
explicit about whether the kernel should be entered in ARM or
Thumb, leading to an ambiguitity about how to enter Thumb-2
kernels. As a result, the kernel is reliant on the zImage
decompressor to enter the kernel proper in the correct instruction
set state.
This patch changes the boot entry protocol for head.S and Image to
be the same as for zImage: in all cases, the kernel is now entered
in ARM.
Documentation/arm/Booting is updated to reflect this new policy.
A different rule will be needed for Cortex-M class CPUs as and when
support for those lands in mainline, since these CPUs don't support
the ARM instruction set at all: a note is added to the effect that
the kernel must be entered in Thumb on such systems.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel space needs very little in the way of BTC maintanence as most
mappings which are created and destroyed are non-executable, and so
could never enter the instruction stream.
The case which does warrant BTC maintanence is when a module is loaded.
This creates a new executable mapping, but at that point the pages have
not been initialized with code and data, so at that point they contain
unpredictable information. Invalidating the BTC at this stage serves
little useful purpose.
Before we execute module code, we call flush_icache_range(), which deals
with the BTC maintanence requirements. This ensures that we have a BTC
maintanence operation before we execute code via the newly created
mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Video input mux settings for tvp7002 and imager inputs were swapped.
Comment was correct.
Tested on EVM with tvp7002 input.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: stable@kernel.org
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Kernel loadable module can use hard_smp_processor_id() if building with SMP
kernel. In order to make it work for UP kernels too, boot_cpuid_phys
symbol (which is what hard_smp_processor_id() macro resolves to
in non-SMP configuration) must be exported.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now we have the CFAR saved add it to the oops output.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
HFI creates interrupts each time a window is setup. This results in
a lot of messages in the kernel log buffer:
irq: irq 199007 on host null mapped to virtual irq 351
This box has over 3500 of them, causing more important kernel
messages to be overwritten. We can get at this information via
debugfs now so we may as well turn it into a pr_debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As a result of changes to Kconfig files, we no longer enable
the lockup and hung task detectors. Both are very light weight
and provide useful information in the event of a hang, so
reenable them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add mpt2sas driver to pseries and ppc64 defconfig.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
