The compactflash device on this platform is not usable simply because it
is never registered with the kernel. Fix that up.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch add platform_device_id which can control
PortA/PortB for FSI2-HDMI from platform data.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the option text to those which appear on the front of the
appropriate board user guides. This gives consistent board naming, and
makes it obvious which option is for which platform.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As no one seems to really know which configuration options tie up with
which boards, I thought I'd do some investigation and try to work it
out. After discussion with some folk in linaro, I think I have this
nailed.
The names are updated to use the name on the front of the appropriate
board user guide for the various baseboards, which I've taken to be
the official name for each board.
I haven't significantly updated the descriptions for the tiles as that
is even less clear - as far as I can see on ARMs website, there is no
Cortex-A9 tile for Realview EB - only ARM11MPCore, ARM1156T2F-S,
ARM1176TZF-S and Cortex-R4F. So exactly what this 'Multicore Cortex-A9
Tile' is...
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two section mismatch warnings in the platform SMP bringup code for
Realview and Versatile Express:
WARNING: arch/arm/mach-realview/built-in.o(.text+0x8ac): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
WARNING: arch/arm/mach-vexpress/built-in.o(.text+0x7b4): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for the family of Systems-on-Chip produced initially
by VIA and now its subsidiary WonderMedia that have recently become
widespread in lower-end Chinese ARM-based tablets and netbooks.
Support is included for both VT8500 and WM8505, selectable by a
configuration switch at kernel build time.
Included are basic machine initialization files, register and
interrupt definitions, support for the on-chip interrupt controller,
high-precision OS timer, GPIO lines, necessary macros for early debug,
pulse-width-modulated outputs control, as well as platform device
configurations for the specific drivers implemented elsewhere.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows a ROM-able zImage to be written to MMC and
for SuperH Mobile ARM to boot directly from the MMCIF
hardware block.
This is achieved by the MaskROM loading the first portion
of the image into MERAM and then jumping to it. This portion
contains loader code which copies the entire image to SDRAM
and jumps to it. From there the zImage boot code proceeds
as normal, uncompressing the image into its final location
and then jumping to it.
Cc: Magnus Damm <magnus.damm@gmail.com>
Russell, please consider merging this for 2.6.38.
This patch depends on:
* "mmc, sh: Move MMCIF_PROGRESS_* into sh_mmcif.h"
which will be merged though Paul Mundt's rmobile sh-2.6.
The absence of this patch will break the build if
the (new) CONFIG_ZBOOT_ROM_MMCIF option is set.
There are no subtle side-effects.
v2:
Addressed comments by Magnus Damm
* Fix copyright in vrl4.c
* Fix use of #define CONFIG_ZBOOT_ROM_MMCIF in mmcif-sh7372.c
* Initialise LED GPIO lines in head-ap4evb.txt instead of mmcif-sh7372.c
as this is considered board-specific.
v3:
Addressed comments made in person by Magnus Damm
* Move mmcif_loader to be earlier in the image and
reduce the number of blocks of boot program loaded by the MaskRom
from 40 to 8 accordingly.
* Move LED GPIO initialisation into mmcif_progress_init
- This leaves the partner jet script unbloated
Other
* inline mmcif_update_progress so it is a static inline in a header file
v4:
* Use htole16() and htole32() in v4rl.c to ensure
that the output is little endian
v5:
Addressed comments by Russell King
* Simplify assembly code
* Jump to code rather than an address <- bug fix
* Use (void __iomem *) as appropriate
Roll in mackerel support
* This was previously a separate patch, only because of the order
in which this code was developed
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the linker script uses 64 for cacheline size which isn't
optimal for all cases. Include asm/cache.h and use L1_CACHE_BYTES
instead as suggested by Sam Ravnborg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Currently percpu readmostly subsection may share cachelines with other
percpu subsections which may result in unnecessary cacheline bounce
and performance degradation.
This patch adds @cacheline parameter to PERCPU() and PERCPU_VADDR()
linker macros, makes each arch linker scripts specify its cacheline
size and use it to align percpu subsections.
This is based on Shaohua's x86 only patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Function _sr_lookup, defined in the same file, returns ERR_PTR not NULL in
an error case.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... return ERR_PTR(...); }
@@
identifier r.f, fld;
expression x;
statement S1,S2;
@@
x = f(...)
... when != IS_ERR(x)
(
if (IS_ERR(x) ||...) S1 else S2
|
*x->fld
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* msm-sdcc:
msm: 8x50: Add initial support for SDCC
mmc: msm_sdcc: Add gpio handling function to driver
drivers: mmc: msm: remove clock disable in probe
mmc: msm: fix dma usage not to use internal APIs
In arch/x86/kernel/dumpstack_64.c::dump_trace() we have this code:
...
if (!stack) {
unsigned long dummy;
stack = &dummy;
if (task && task != current)
stack = (unsigned long *)task->thread.sp;
}
bp = stack_frame(task, regs);
/*
* Print function call entries in all stacks, starting at the
* current stack address. If the stacks consist of nested
* exceptions
*/
tinfo = task_thread_info(task);
for (;;) {
char *id;
unsigned long *estack_end;
estack_end = in_exception_stack(cpu, (unsigned long)stack,
&used, &id);
...
You'll notice that we assign to 'stack' the address of the variable
'dummy' which is only in-scope inside the 'if (!stack)'. So when we later
access stack (at the end of the above, and assuming we did not take the
'if (task && task != current)' branch) we'll be using the address of a
variable that is no longer in scope. I believe this patch is the proper
fix, but I freely admit that I'm not 100% certain.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
LKML-Reference: <alpine.LNX.2.00.1101242232590.10252@swampdragon.chaosbits.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: DMA: clear interrupt status correctly
OMAP3: Devkit8000: Fix tps65930 pullup/pulldown configuration
arm: omap3: cm-t3517: minor comment fix
arm: omap3: cm-t3517: rtc fix
omap1: Fix sched_clock implementation when both MPU timer and 32K timer are used
omap1: Fix booting for 15xx and 730 with omap1_defconfig
omap1: Fix sched_clock for the MPU timer
OMAP: PRCM: remove duplicated headers
OMAP4: clockdomain: bypass unimplemented wake-up dependency functions on OMAP4
OMAP: counter_32k: init clocksource as part of machine timer init
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix time function double declaration with glibc
perf tools: Fix build by checking if extra warnings are supported
perf tools: Fix build when using gcc 3.4.6
perf tools: Add missing header, fixes build
perf tools: Fix 64 bit integer format strings
perf test: Fix build on older glibcs
perf: perf_event_exit_task_context: s/rcu_dereference/rcu_dereference_raw/
perf test: Use cpu_map->[cpu] when setting affinity
perf symbols: Fix annotation of thumb code
perf: Annotate cpuctx->ctx.mutex to avoid a lockdep splat
powerpc, perf: Fix frequency calculation for overflowing counters (FSL version)
perf: Fix perf_event_init_task()/perf_event_free_task() interaction
perf: Fix find_get_context() vs perf_event_exit_task() race
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix jump label with RO/NX module protection crash
x86, hotplug: Fix powersavings with offlined cores on AMD
x86, mcheck, therm_throt.c: Export symbol platform_thermal_notify to allow coretemp to handler intr
x86: Use asm-generic/cacheflush.h
x86: Update CPU cache attributes table descriptors
lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006. As such, it is a maintainence burden with no benefit.
This gets rid of two defconfigs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is completely board specific and therefore must be provided
on a per-board basis.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
adds rtc support for all Gemini SoC boards
nas4220b, rut1xx, wbd111, wbd222
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
_CLK_SET_RATE does not only handle the cpu clock but also other
clocks, so do not hardcode the HW_CLKCTRL_CPU register.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
reg | (1 << clk->enable_shift) always evaluates to true. Switch it
to & which makes much more sense
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
If we use jump table in module init, there are marked
as removed in __jump_table section after init is done.
But we already applied ro permissions on the module, so
we can't modify a read only section (crash in
remove_jump_label_module_init).
Make the __jump_table section rw.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Siarhei Liakh <sliakh.lkml@gmail.com>
Cc: Xuxian Jiang <jiang@cs.ncsu.edu>
Cc: James Morris <jmorris@namei.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@redhat.com>
Cc: Kees Cook <kees.cook@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4D3C3F20.7030203@free.fr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
`debug=mem' on Amiga has been broken for a while.
early_param() processing is done very/too early, i.e. before
amiga_identify() / amiga_chip_init(), causing amiga_savekmsg_setup() not
to find any Chip RAM.
As we don't plan to free this memory anyway, just steal it from the initial
Chip RAM memory block instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
It's a way too generic name for a global #define and conflicts with a variable
with the same name, causing build errors like:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c: In function ‘_si_clkctl_cc’:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected identifier or ‘(’ before ‘volatile’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected ‘)’ before ‘(’ token
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1421: error: incompatible types in assignment
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1422: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1423: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1424: error: invalid operands to binary |
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: incompatible type for argument 4 of ‘bcmsdh_reg_write’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1428: error: invalid operands to binary &
| make[8]: *** [drivers/staging/brcm80211/brcmfmac/../util/siutils.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
There's a small memory leak in
arch/x86/crypto/aesni-intel_glue.c::rfc4106_set_hash_subkey(). If the call
to kmalloc() fails and returns NULL then the memory allocated previously
by ablkcipher_request_alloc() is not freed when we leave the function.
I could have just added a call to ablkcipher_request_free() before we
return -ENOMEM, but that started to look too much like the code we
already had at the end of the function, so I chose instead to rework the
code a bit so that there are now a few labels at the end that we goto when
various allocations fail, so we don't have to repeat the same blocks of
code (this also reduces the object code size slightly).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some versions of gcc replace calls to strstr() with single-character
"needle" string parameters by calls to strchr() behind our back.
If strchr() is defined as an inline function, this causes linking errors
like
ERROR: "strchr" [drivers/target/target_core_mod.ko] undefined!
As m68k is the only architecture that has an inline strchr() and this
inline version is not an optimized asm version, uninline strchr() and use
the standard out-of-line C version in lib/string.c instead.
This also decreases the defconfig/allmodconfig kernel image sizes by a few
hundred bytes.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
ea53069231 made a CPU use monitor/mwait
when offline. This is not the optimal choice for AMD wrt to powersavings
and we'd prefer our cores to halt (i.e. enter C1) instead. For this, the
same selection whether to use monitor/mwait has to be used as when we
select the idle routine for the machine.
With this patch, offlining cores 1-5 on a X6 machine allows core0 to
boost again.
[ hpa: putting this in urgent since it is a (power) regression fix ]
Reported-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org # 37.x
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.hl>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1295534572-10730-1-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add a name field to the I/O resources for the UARTs on MSM
targets in preparation for updates to the msm_serial
driver. The driver assumed there is one I/O resource per
UART, which is not the case on all targets.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add the machine record, init code, and build support for
the MSM8960 RUMI3.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add the board file, Kconfig options, and Makefile options
needed to build for the MSM8960 Simulator target.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Clean up some of the conditionals in the Makefile in
preparation for adding build support for MSM8960.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Modify the macros in the MSM timer driver to support the
MSM8960 chip.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add the interrupt map for the Qualcomm MSM8960 chip. This
chip has an interrupt map that is different from previous
targets.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add the physical memory offset value for the Qualcomm
MSM8960 chip.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add the register address definitions for the basic hardware
blocks on the Qualcomm MSM8960 chip.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
The QGIC registers are mapped to the same virtual addresses across
targets, only the physical address changes. Move the BASE address out
of target-specific files, and add a SOC name to the base addresses.
Signed-off-by: David Brown <davidb@codeaurora.org>
Allow the timer register to be determined dynamically instead of at
compile time. Use common virtual addresses for the registers across
all MSM chips, and select the register mappings based on the detected
CPU.
Signed-off-by: David Brown <davidb@codeaurora.org>
