Prevent the long delay in io_check_error making NMI watchdog
timeout.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The spin_lock_debug/rcu_cpu_stall detector uses
trigger_all_cpu_backtrace() to dump cpu backtrace.
Therefore it is possible that trigger_all_cpu_backtrace()
could be called at the same time on different CPUs, which
triggers and 'unknown reason NMI' warning. The following case
illustrates the problem:
CPU1 CPU2 ... CPU N
trigger_all_cpu_backtrace()
set "backtrace_mask" to cpu mask
|
generate NMI interrupts generate NMI interrupts ...
\ | /
\ | /
The "backtrace_mask" will be cleaned by the first NMI interrupt
at nmi_watchdog_tick(), then the following NMI interrupts
generated by other cpus's arch_trigger_all_cpu_backtrace() will
be taken as unknown reason NMI interrupts.
This patch uses a test_and_set to avoid the problem, and stop
the arch_trigger_all_cpu_backtrace() from calling to avoid
dumping a double cpu backtrace info when there is already a
trigger_all_cpu_backtrace() in progress.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Reviewed-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Cc: fweisbec@gmail.com
LKML-Reference: <1294198689-15447-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Don Zickus <dzickus@redhat.com>
There are some paths that walk the die_chain with preemption on.
Make sure we are in an NMI call before we start doing anything.
This was triggered by do_general_protection calling notify_die
with DIE_GPF.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Found one x2apic pre-enabled system, x2apic_mode suddenly get
corrupted after register some cpus, when compiled
CONFIG_NR_CPUS=255 instead of 512.
It turns out that generic_processor_info() ==> phyid_set(apicid,
phys_cpu_present_map) causes the problem.
phys_cpu_present_map is sized by MAX_APICS bits, and pre-enabled
system some cpus have an apic id > 255.
The variable after phys_cpu_present_map may get corrupted
silently:
ffffffff828e8420 B phys_cpu_present_map
ffffffff828e8440 B apic_verbosity
ffffffff828e8444 B local_apic_timer_c2_ok
ffffffff828e8448 B disable_apic
ffffffff828e844c B x2apic_mode
ffffffff828e8450 B x2apic_disabled
ffffffff828e8454 B num_processors
...
Actually phys_cpu_present_map is referenced via apic id, instead
index. We should use MAX_LOCAL_APIC instead MAX_APICS.
For 64-bit it will be 32768 in all cases. BSS will increase by 4k bytes
on 64-bit:
text data bss dec filename
21696943 4193748 12787712 38678403 vmlinux.before
21696943 4193748 12791808 38682499 vmlinux.after
No change on 32bit.
Finally we can remove MAX_APCIS that was rather confusing.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4D23BD9C.3070102@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is not related to init_memory_mapping(), and init_memory_mapping() is
getting more bigger.
So make it as seperated function and call it from reserve_brk() and that is
point when _brk_end is concluded.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D1933E0.7090305@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When the seqfile /proc/cpuinfo gets accesses for each possible cpu
loops_per_jiffy gets recalculated. However its value is only needed
on first access.
In addition loops_per_jiffy should be recalculated when the machine
reports a capability change.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use get_online_cpus() instead of preempt_disable() to make sure cpus
don't go offline while accessing their per cpu data.
The preempt_disable() stuff is old code which was used before
get_online_cpus() was available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of messages that indicate if a cpu went online or offline.
There is nothing special about this anymore and these messages might
flood the kernel log buffer which makes debugging harder since more
important messages might be overwritten.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This enables the spinning mutex feature on s390 by removing
HAVE_DEFAULT_NO_SPIN_MUTEXES from arch/s390/Kconfig.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The spinning mutex implementation uses cpu_relax() in busy loops as a
compiler barrier. Depending on the architecture, cpu_relax() may do more
than needed in this specific mutex spin loops. On System z we also give
up the time slice of the virtual cpu in cpu_relax(), which prevents
effective spinning on the mutex.
This patch replaces cpu_relax() in the spinning mutex code with
arch_mutex_cpu_relax(), which can be defined by each architecture that
selects HAVE_ARCH_MUTEX_CPU_RELAX. The default is still cpu_relax(), so
this patch should not affect other architectures than System z for now.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290437256.7455.4.camel@thinkpad>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Call init_idle() which (re-)initializes the idle task structure before
it gets used on a new cpu.
That way we can also get rid of the odd preempt_enable_no_resched()
call we have in the cpu offline path within cpu_idle(). That call
prevented preempt count imbalances between cpu hotplug operations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Delay idle task creation until a cpu gets set online instead of
creating them for all possible cpus at system startup.
For one cpu system this should safe more than 1 MB.
On my debug system with lots of debug stuff enabled this saves 2 MB.
Same as on x86.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Normal I/O operations through the DASD device driver give only access
to the data fields of an ECKD device even for track based I/O.
This patch extends the DASD device driver to give access to whole
ECKD tracks including count, key and data fields.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a DASD device has been reserved by a Linux system, and later
this reservation is ‘stolen’ by a second system by means of an
unconditional reserve, then the first system receives a
notification about this fact. With this patch such an event can
be either ignored, as before, or it can be used to let the device
fail all I/O request, so that the device will not block anymore.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Until now machine checks for the swapper process of the IPL cpu are just
implicitly (and more or less accidently) enabled when the first time the
idle process goes into idle state and loads an enabled wait psw.
Before that machine checks are disabled.
So let's enable them explicitly in trap_init() so we have a well defined
time when machine checks are enabled.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the code in the 31 bit entry.S code as similar as possible to the
64 bit version in entry64.S. That makes it easier to add new code to
the first level interrupt handler that affects both 31 and 64 bit kernels.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support to accumulate the number of 64K-bytes blocks all paths
to a device at least support for a transport command.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch_needs_cpu() gets always executed on the current cpu. Therefore
the cpu parameter can be ignored it is possible to use __get_cpu_var()
instead of per_cpu() to access the per_cpu variable, which will
generate better code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a scan treshold for the qdio outbound queues. By setting the
threshold the driver can tell qdio after how much used SBALs qdio
should schedule the outbound tasklet that scans the queue for finished
SBALs. The threshold is specific by the drivers because a
Hipersockets device is much faster in utilizing outbound buffers than a
ZFCP or OSA device.
The default values after how many used SBALs the tasklet should run are:
OSA: > 31 SBALs
Hipersockets: > 7 SBALs
zfcp: > 55 SBALs
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the buffer for diagnose data is allocated in the open function
of the debugfs file and is released in the close function. This has the
drawback that a user (root) can pin that memory by not closing the file.
This patch moves the buffer allocation to the read function. The buffer is
automatically released after the buffer is copied to userspace.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of register/unregister_early_external_interrupt() and clean up
the code while at it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use an early init call to initialize pfault. That way it is possible to
use the register_external_interrupt() instead of the early variant.
No need to enable pfault any earlier since it has only effect if user
space processes are running.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for AP Bus I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for CTC I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for CLAW I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for LCS I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for VMUR I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for ccw based tape I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for 3270 I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for 3215 I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for DASD I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Count traditional qdio interrupts and adapter interrupts for qdio
in the interrupt statistics.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Up to now /proc/interrupts only has statistics for external and i/o
interrupts but doesn't split up them any further.
This patch adds a line for every single interrupt source so that it
is possible to easier tell what the machine is/was doing.
Part of the output now looks like this;
CPU0 CPU2 CPU4
EXT: 3898 4232 2305
I/O: 782 315 245
CLK: 1029 1964 727 [EXT] Clock Comparator
IPI: 2868 2267 1577 [EXT] Signal Processor
TMR: 0 0 0 [EXT] CPU Timer
TAL: 0 0 0 [EXT] Timing Alert
PFL: 0 0 0 [EXT] Pseudo Page Fault
[...]
NMI: 0 1 1 [NMI] Machine Checks
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let local_tick_enable/disable() reprogram the clock comparator so the
function names make semantically more sense.
Also that way the functions are more symmetric since normally each
local_tick_enable() call usually would have a subsequent call to
set_clock_comparator() anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the two functions to timex.h where they make more sense than in
hardirq.h.
No functional change.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add kprobes annotations to get the massive 'probe kernel.function("*") {}'
stress test working.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Restructure the kprobe breakpoint handler function. Add comments to
make it more comprehensible and add a sanity check for re-entering
kprobes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Register %r14 and %r15 are already stored in jprobe_saved_regs, no need
to store them a second time in jprobe_saved_r14 / jprobe_saved_r15.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 architecture can execute code on kmalloc/vmalloc memory.
No need for the __ARCH_WANT_KPROBES_INSN_SLOT detour.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace set_current_kprobe/reset_current_kprobe/save_previous_kprobe/
restore_previous_kprobe with a simpler scheme push_kprobe/pop_kprobe.
The mini kprobes stack can store up to two active kprobes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Determine instruction fixup details in resume_execution, no need to do
it beforehand. Remove fixup, ilen and reg from arch_specific_insn.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the definition of the helper structure ins_replace_args to the
only place where it is used and drop the old member as it is not needed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The saved interrupt mask and the saved control registers are only
relevant while single stepping is set up. A secondary kprobe while
kprobe single stepping is active may not occur. That makes is safe
to remove the save and restore of kprobe_saved_imask / kprobe_save_ctl
from save_previous_kprobe and restore_previous_kprobe.
Move all single step related code to two functions, enable_singlestep
and disable_singlestep.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove special case of a kprobe on a breakpoint while a relocated
instruction is single stepped. The only instruction that may cause
a fault while kprobe single stepping is active is the relocated
instruction. There is no kprobe on the instruction slot retrieved
with get_insn_slot().
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
