The IOP driver calls into the OSS driver to enable its IRQ. This undesirable coupling between drivers only exists because the OSS driver doesn't correctly handle all of its machspec IRQs.
Fix OSS handling of enable/disable for VIA1 IRQs (8 thru 15) which includes MAC_IRQ_ADB.
Back when I implemented pmac_zilog support I redefined IRQ_MAC_SCC incorrectly. Change this to a machspec IRQ so that it works on OSS.
Clean up the unused OSS audio IRQ and OSS_IRQLEV_* cruft that only confuses things.
Fix the OSS description in macints.c and remove an obsolete comment.
Don't enable the VIA1 irq before registering the handler.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Improve NuBus slot interrupt handling code and documentation. This patch fixes the NuBus NIC (mac8390) in my Quadra 700.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Enable via_alt_mapping on the Performa 588 and tidy up related documentation.
I'm betting that remapped IRQs work just fine on the Performa 580 series since it works on the LC 630 and the logic board part numbers are reputedly the same.
And the consensus seems to be that the Mac TV is essentially a Performa 550, not dissimilar to the Performa 520, so set the via_type accordingly.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move some forward declarations into header files and adjust includes.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
mac_irq_pending() has only one caller (mac_esp.c). Nothing tests for Baboon, PSC or OSS pending interrupts. Until that need arises, let's keep it simple and remove all the unused abstraction. Replace it with a routine to check for SCSI DRQ.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
mac_clear_irq() is dead code and has been dead for as long as I can recall. On certain Mac models, certain irqs can't be cleared this way. Outside of irq dispatch, this code appears be unusable without busy loops or worse, and for irq dispatch we duplicate the same logic. Remove mac_clear_irq() and supporting code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Revive the old mac_serial_print() routine as mac_early_print(). mac_serial_print() did not function because it did not use the right offsets for its stack arguments. Fix this and make compilation conditional on CONFIG_EARLY_PRINTK instead of the obscure MAC_SERIAL_DEBUG macro.
Give mac_early_print() a new string length parameter to fit the early console API.
Send output to the framebuffer as well as serial ports.
Change the line rate to 38400 baud to match the default for the real (pmac_zilog) serial console.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Added support for EARLY_PRINTK when running on an MVME16x board.
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Only define SERIAL_PORT_DFNS when CONFIG_ISA is defined. Otherwise the first
4 slots in the 8250 driver are unavailable on non-ISA machines.
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Sending a break on the SOC UARTs found in some MPC83xx/85xx/86xx
chips seems to cause a short lived IRQ storm (/proc/interrupts
typically shows somewhere between 300 and 1500 events). Unfortunately
this renders SysRQ over the serial console completely inoperable.
The suggested workaround in the errata is to read the Rx register,
wait one character period, and then read the Rx register again.
We achieve this by tracking the old LSR value, and on the subsequent
interrupt event after a break, we don't read LSR, instead we just
read the RBR again and return immediately.
The "fsl,ns16550" is used in the compatible field of the serial
device to mark UARTs known to have this issue.
Thanks to Scott Wood for providing the errata data which led to
a much cleaner fix.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce a symbol, EFI_LOADER_SIGNATURE instead of using the magic
strings, which also helps to reduce the amount of ifdeffery.
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1318848017-12301-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
commit 37ba7ab5e3 ("x86, boot: make kernel_alignment adjustable; new
bzImage fields") introduced some new fields into the bzImage header
but struct setup_header was not updated accordingly. Add the missing
'pref_address' and 'init_size' fields.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1318848017-12301-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
efi_call_phys_prelog() sets up a 1:1 mapping of the physical address
range in swapper_pg_dir. Instead of replacing then restoring entries
in swapper_pg_dir we should be using initial_page_table which already
contains the 1:1 mapping.
It's safe to blindly switch back to swapper_pg_dir in the epilog
because the physical EFI routines are only called before
efi_enter_virtual_mode(), e.g. before any user processes have been
forked. Therefore, we don't need to track which pgd was in %cr3 when
we entered the prelog.
The previous code actually contained a bug because it assumed that the
kernel was loaded at a physical address within the first 8MB of ram,
usually at 0x100000. However, this isn't the case with a
CONFIG_RELOCATABLE=y kernel which could have been loaded anywhere in
the physical address space.
Also delete the ancient (and bogus) comments about the page table
being restored after the lock is released. There is no locking.
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Darrent Hart <dvhart@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1323346250.3894.74.camel@mfleming-mobl1.ger.corp.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
While working on the upcoming SLES11 SP2, I ran into an issue with booting the
panic kernel on a kernel crash. In the first iteration I found out that the
initial register backing store gets overwritten with zeroes, causing a kernel
crash shortly afterwards.
Further investigation revealed that rsvd_region[] contains overlapping
entries: find_memmap_space() returns a pointer which lies between KERNEL_START
and _end. This is correct with the EFI memmap as patched by the kexec
purgatory code. That code removes vmlinux LOAD segments from the usable map,
but there is a pretty large hole between the gate section and the per-cpu
section.
This happens because reserve_memory() blindly marks [KERNEL_START, __end]
as reserved, even though there is a free block in the middle in the kexec
case because it noticed a large gap between sections and modified the
efi_memory_map to account for this.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Calling __pa() with an ioremap()ed address is invalid
x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked
x86/intel_mid: Kconfig select fix
x86/intel_mid: Fix the Kconfig for MID selection
The S3C64xx SoCs contain a set of gateable power domains which can be
enabled and disabled at runtime in order to save power. Use the generic
power domain code to implement support for these in software, enabling
runtime control of most domains:
- ETM (not supported in mainline).
- Domain G: 3D acceleration (no mainline support).
- Domain V: MFC (no mainline support).
- Domain I: JPEG and camera interface (no mainline support).
- Domain P: 2D acceleration, TV encoder and scaler (no mainline support)
- Domain S: Security (no mainline support).
- Domain F: LCD (driver already uses runtime PM), post processing and
rotation (no mainline support).
The IROM domain is marked as always enabled as we should arrange for it
to be enabled when we suspend which will need a bit more work.
Due to all the conditional device registration that the platform does
wrap s3c_pm_init() with s3c64xx_pm_init() which actually puts the device
into the power domain after the machines have registered, looking for
platform data to tell if the device was registered. Since currently only
Cragganmore actually sets up PM that is the only machine updated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Saves a tiny amount of code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If the DMA destination position has been asked before the
first actual data transfer has been done, the CDAC
register still contains 0 (it is initialized to 0 at
omsp_dma_start).
If CDAC == 0, return the programmed start address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the DMA source position has been asked before the
first actual data transfer has been done, the CSAC
register does not contain valid information.
We can identify this situation by checking the CDAC
register:
CDAC != 0 indicates that the DMA transfer on the channel has
been started already.
When CDAC == 0 we can not trust the CSAC value since it has
not been updated, and can contain random number.
Return the start address in case the DMA has not jet started.
Note: The CDAC register has been initialized to 0 at dma_start
time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for base-board MMC slot
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error message which appears
while intializing MMC1 on the AM3517 EVM base-board:
mmc0: host doesn't support card's voltages
mmc0: error -22 whilst initialising SD card
The ocr_mask, which enumerates the volatges supported by the
MMC card was not being indicated before, assuming that a separate
Vcc regulator maybe another controllable regulator driver would be
doing this. This patch statically specifies a subset of the voltages
supported by the MMC driver, which are provided by the current fixed
voltage regulator on AM3517 EVM.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Devkit8000 uses a TWL4030 pin for card detection.
Thats why the error:
_omap_mux_init_gpio: Could not set gpio192
occurs.
This patch checks that the pin is on OMAP before
calling omap_mux_init_gpio.
Signed-off-by: Thomas Weber <weber@corscience.de>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM35x MMC 2 controller has internal clock loopback setting which cannot
be utilized without this patch and thus SDIO devices connected to this
controller and depend on this setting will fail to initialize.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Declare support for keeping the power of the wlan chip
while suspended. this is needed for Wakeup-On-Wireless.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We override sys_iopl(), not stub_iopl(); the latter is a 64-bitism
that doesn't apply to i386 in the first place.
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
$(KBUILD_SRC) is not defined without O=, use $(srctree).
Reported-and-tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: use new generic {enable,disable}_percpu_irq() routines
drivers/net/ethernet/tile: use skb_frag_page() API
asm-generic/unistd.h: support new process_vm_{readv,write} syscalls
arch/tile: fix double-free bug in homecache_free_pages()
arch/tile: add a few #includes and an EXPORT to catch up with kernel changes.
With the 3.2-rc kernel, IOMMU 2M pages in KVM works. But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.
The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd. If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.
So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.
This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.
Reproduce like:
1. Add grub boot option: hugepagesz=1G hugepages=8
2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages
3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages
-net none -device pci-assign,host=07:00.1
kernel BUG at mm/swap.c:114!
invalid opcode: 0000 [#1] SMP
Call Trace:
put_page+0x15/0x37
kvm_release_pfn_clean+0x31/0x36
kvm_iommu_put_pages+0x94/0xb1
kvm_iommu_unmap_memslots+0x80/0xb6
kvm_assign_device+0xba/0x117
kvm_vm_ioctl_assigned_device+0x301/0xa47
kvm_vm_ioctl+0x36c/0x3a2
do_vfs_ioctl+0x49e/0x4e4
sys_ioctl+0x5a/0x7c
system_call_fastpath+0x16/0x1b
RIP put_compound_page+0xd4/0x168
Signed-off-by: Youquan Song <youquan.song@intel.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
CONFIG_PPC47x doesn't exist in Kconfig and no 476 processor calls this
function ppc44x_pin_tlb() as it has it's own ppc47x_pin_tlb().
This code is probably an artifact of the original 476 code that
shouldn't have made it upstream.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Needed if you want to use swiotlb, harmless otherwise.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.
Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Since commit 6571534 (plat-mxc: iomux-v3.h: implicitly enable
pull-up/down when that's desired) was in, the power button on imx51
babbage board stopped working because it's pulled up by mistake.
The patch removes the pull-up setting from the pad configuration for
that gpio to make the power button back to work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CC arch/arm/plat-mxc/cpufreq.o
arch/arm/plat-mxc/cpufreq.c:203: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:203: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:203: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
arch/arm/plat-mxc/cpufreq.c:203: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:204: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:204: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:204: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
arch/arm/plat-mxc/cpufreq.c:204: warning: function declaration isn't a prototype
arch/arm/plat-mxc/cpufreq.c:205: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-mxc/cpufreq.c:205: warning: data definition has no type or storage class
arch/arm/plat-mxc/cpufreq.c:205: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
arch/arm/plat-mxc/cpufreq.c:205: warning: function declaration isn't a prototype
make[1]: *** [arch/arm/plat-mxc/cpufreq.o] Error 1
make: *** [arch/arm/plat-mxc] Error 2
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.
On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:
BUG: unable to handle kernel paging request at f7f22280
IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
[...]
Call Trace:
[<c104f8ca>] ? page_is_ram+0x1a/0x40
[<c1025aff>] reserve_memtype+0xdf/0x2f0
[<c1024dc9>] set_memory_uc+0x49/0xa0
[<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
[<c19216d4>] start_kernel+0x291/0x2f2
[<c19211c7>] ? loglevel+0x1b/0x1b
[<c19210bf>] i386_start_kernel+0xbf/0xc8
A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().
Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,
https://bugzilla.redhat.com/show_bug.cgi?id=748516
Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds constraint checks to the numa_set_distance()
function.
When the check triggers (this should not happen normally) it
emits a warning and avoids a store to a negative index in
numa_distance[] array - i.e. avoids memory corruption.
Negative ids can be passed when the pxm-to-nids mapping is not
properly filled while parsing the SRAT.
Signed-off-by: Petr Holasek <pholasek@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Anton Arapov <anton@redhat.com>
Link: http://lkml.kernel.org/r/20111208121640.GA2229@dhcp-27-244.brq.redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The get_cpu_cap() external function prototype was declared twice
so lose one of them.
Clean up the header guard while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1322594083-14507-1-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
DPLL1 reprogramming to a different rate is actually blocked inside
omap1_select_table_rate(). However, it is already forced at boot, for
boards which boot at unusable clock rates, and this seems to work
correctly.
OTOH, we now have a fine, run time performed clock selection algorithm
implemented, which prevents less powerfull SoCs from being overclocked
unintentionally.
Allow reprogramming of dpll1 by default, and use it for switching to the
higest supported clock rate with all boards, including those already
booting at a usable rate of 60 MHz or above.
Created against linux-omap/master tip as of Thu Dec 1,
commit f83c2a8cbb59981722d1ab610c79adfd034a2667. Requires the just
submitted patch "ARM: OMAP1: Move dpll1 rates selection from config to
runtime" to prevent from unintentional overclocking. Tested on Amstrad
Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
