USB2.0 Device Controller (U2DC) which is found in Marvell PXA3xx.
U2DC supports both High and Full speed modes.
PXA320 and PXA300 U2DC supports only UTMI interface.
PXA310 U2DC supports only ULPI interface and has the OTG capability.
U2D Controller ULPI driver introduced in this patch supports only the
PXA310 USB Host via the ULPI.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Avoids a potential infinite loop.
It was observed once, during an EC hacking/debugging
session - not in regular operation.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: dilinger@queued.net
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel Medfield platform has a high speed UART device, which
could act as a early console. To enable early printk of HSU
console, simply add "earlyprintk=hsu" in kernel command line.
Currently we put the code in the early_printk_mrst.c as it is
also for Intel MID platforms like the mrst early console
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: greg@kroah.com
LKML-Reference: <1284361736-23011-5-git-send-email-feng.tang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel Moorestown platform has a spi-uart device(Maxim3110),
which connects to a Designware spi core controller. This patch
will add early console function based on it.
As it will be used long before Linux spi subsystem get
initialised, we simply directly manipulate the spi controller's
register to acheive the early console func. This is safe as it
will be disabled when devices subsytem get initialised.
To use it, user need enable CONFIG_X86_MRST_EARLY_PRINTK in
kenrel config and add "earlyprintk=mrst" in kernel command line.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: greg@kroah.com
LKML-Reference: <1284361736-23011-4-git-send-email-feng.tang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sometimes fixmap will be used to map an physical address which
is not PAGE align, so to use it we need first map it and then
add the address offset to the mapped fixed address. These 2 new
helpers are suggested by Ingo Molnar to make the process
simpler.
For a physicall address like "phys", a directly usable virtual
address can be get by
virt = (void *)set_fixmap_offset(fixed_idx, phys);
or
virt = (void *)set_fixmap_offset_nocache(fixed_idx, phys);
(depends on whether the physical address is cachable or not).
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: alan@linux.intel.com
Cc: greg@kroah.com
Cc: x86@kernel.org
LKML-Reference: <1284361736-23011-3-git-send-email-feng.tang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
An earlier patch fixed the hwpoison fault handling to encode the
huge page size in the fault code of the page fault handler.
This is needed to report this information in SIGBUS to user space.
This is a straight forward patch to pass this information
through to the signal handling in the x86 specific fault.c
Cc: x86@kernel.org
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: fengguang.wu@intel.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Fix typo in commit dbe3039 ("memblock/arm: Use memblock_region_is_memory()
for omap fb") - it should be memblock_is_region_memory().
Reported-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: ext Grazvydas Ignotas <notasas@gmail.com>
LKML-Reference: <4CABFADA.9020305@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Serial drivers call get_clock() very early, before platform bus
has been set up, this requires a special check to let them get
a proper clock. Without this patch, a serial console is broken
on S5PV310 and S5PC210 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: fix coding-style]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch adds header <linux/sched.h> into the below files for build with
CONFIG_PREEMPT_NONE.
arch/arm/mach-s5p6440/cpu.c
arch/arm/mach-s5p6442/cpu.c
arch/arm/mach-s5pc100/cpu.c
arch/arm/mach-s5pv210/cpu.c
Following is error message of in case of s5pv210_defconfig with CONFIG_PREEMPT_NONE.
arch/arm/mach-s5pv210/cpu.c:91: error: implicit declaration of function 'need_resched'
Signed-off-by: SeungChull Suh <sc.suh@samsung.com>
[kgene.kim@samsung.com: removed mach-s5p64x0/cpu.c]
[kgene.kim@samsung.com: added fix mach-s5p6440/cpu.c]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes following unused codes for removing build warnings.
arch/arm/plat-samsung/adc.c:438: warning: unused variable 'flags'
arch/arm/mach-s5pv210/clock.c:176: warning: 's5pv210_clk_ip4_ctrl' defined but not used
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The kernel decompression code parses the ELF header and then copies
the segment to the corresponding destination. Currently it uses slow
byte-copy code. This patch makes it use the string copy operations
instead.
In the test the copy performance can be improved very significantly after using
the string copy operation mechanism.
1. The copy time can be reduced from 150ms to 20ms on one Atom machine
2. The copy time can be reduced about 80% on another machine
The time is reduced from 7ms to 1.5ms when using 32-bit kernel.
The time is reduced from 10ms to 2ms when using 64-bit kernel.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
LKML-Reference: <1286502453-7043-1-git-send-email-yakui.zhao@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
A function in a header file needs to be explicitly marked "inline", or
gcc will complain if it is not used.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: <stable@kernel.org> v2.6.36
LKML-Reference: <1274295685-6774-3-git-send-email-jacob.jun.pan@linux.intel.com>
On 32-bit non-PAE system, cast to 'phys_addr_t' truncates value
before subtraction. Subtracting before cast produce same result
but remove following warnings from sparse:
arch/x86/include/asm/pgtable_types.h:255:38: warning: cast truncates bits from constant value (100000000 becomes 0)
arch/x86/include/asm/pgtable_types.h:270:38: warning: cast truncates bits from constant value (100000000 becomes 0)
arch/x86/include/asm/pgtable.h:127:32: warning: cast truncates bits from constant value (100000000 becomes 0)
arch/x86/include/asm/pgtable.h:132:32: warning: cast truncates bits from constant value (100000000 becomes 0)
arch/x86/include/asm/pgtable.h:344:31: warning: cast truncates bits from constant value (100000000 becomes 0)
64-bit or PAE machines will not be affected by this change.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
LKML-Reference: <1285770588-14065-1-git-send-email-namhyung@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This is called before early_irq_init() which will clobber any
registrations made too early. Move the calls to ia64_mca_late_init().
Signed-off-by: Tony Luck <tomy.luck@intel.com>
The speed and clock of the serial ports is retrieved from the device
tree in both the PowerPC legacy serial code and the Open Firmware serial
driver, therefore they need to handle the fact that the device tree is
always big endian, while the CPU may not be.
Also fix other device tree references in the legacy serial code.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
All platform data has to be made conditional on CONFIG_STEDMA40
or we can provide a simple dummy filter functions as to avoid
cluttering the code with other #ifdef:s.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove obsolete pre_transfer hook in stedma40_chan_cfg. The
intent of this hook is merely to handle burst size
compensation for ux500 variant MMCI. Remove obsolete stedma40_set_psize
since it is only called from pre_transfer. DMAEngine device_control
replaces the functionality of stedma40_set_psize.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the generic DMAEngine API has support for scatterlist to
scatterlist copying, the device_prep_slave_sg() portion of the
DMA_SLAVE API is no longer necessary and has been removed.
However, the device_control() portion of the DMA_SLAVE API is still
useful to control device specific parameters, such as externally
controlled DMA transfers and maximum burst length.
A special dma_ctrl_cmd has been added to enable externally controlled
DMA transfers. This is currently specific to the Freescale DMA
controller, but can easily be made generic when another user is found.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch add a LED class driver for LEDs found on the LaCie 2Big and
5Big Network v2 boards. The LEDs are wired to a CPLD and are controlled
through a GPIO extension bus.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Many Atmel SOC are embedding a MACB controller. This patch removes the long
dependency line for this Atmel MACB ethernet driver configuration entry.
The HAVE_NET_MACB configuration option is located in the net Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: David Miller <davem@davemloft.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
The simpler AT91x40 processors do not have the same power management
controller as the new AT91 devices. They do have a simpler power
controller module that we can use to disable the CPU clock at idle
time. Add code to support that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The MTD nand driver for Atmel chips is atmel_nand and not at91_nand anymore.
Change wrong configuration variables that were remaining.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Today the board use 2 machines id AT91SAM9G45EKES and AT91SAM9M10G45EK
now will use only AT91SAM9M10G45EK.
The other boards revision will be specified via system_rev.
for 9g45ekes, m10g45ekes and m10g45ek boards and revisions
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Add missing consts to the sys_execve() declaration which result in the
following error:
arch/sh/kernel/process_32.c:303: error: conflicting types for 'sys_execve'
/warthog/nfs/linux-2.6-fscache/arch/sh/include/asm/syscalls_32.h:24: error: previous declaration of 'sys_execve' was here
Signed-off-by: David Howells <dhowells@redhat.com>
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch. This renames local_*_hw() to hard_local_*() using the
following perl command:
perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`
and then fixing up asm/irqflags.h manually.
Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a missing dependency (mach/blackfin.h) to asm/irqflags.h so that
bfin_read_IMASK() can be used by inline functions.
Signed-off-by: David Howells <dhowells@redhat.com>
Split the BF532 machine type BFIN_*_FIO_FLAG() functions to their own header
file to avoid circular #include problems as these functions require IRQ flag
handling, which requires asm/blackfin.h, which otherwise requires the header
file that defines these functions.
For good measure, also get rid of the inclusion of asm/blackfin.h from
mach/cdefBF532.h (which is circular) and defBF532.h (which is included by
asm/blackfin.h before including this header).
Signed-off-by: David Howells <dhowells@redhat.com>
Split the PLL control code from the Blackfin machine-specific cdef headers so
that the irqflags functions can be renamed without incurring a header loop.
Signed-off-by: David Howells <dhowells@redhat.com>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Octeon: Place cnmips_cu2_setup in __init memory.
MIPS: Don't place cu2 notifiers in __cpuinitdata
MIPS: Calculate VMLINUZ_LOAD_ADDRESS based on the length of vmlinux.bin
MIPS: Alchemy: Resolve prom section mismatches
MIPS: Fix syscall 64 bit number comments.
MIPS: Hookup fanotify_init, fanotify_mark, and prlimit64 syscalls.
MIPS: TX49xx: Rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
MIPS: N32: Fix getdents64 syscall for n32
MIPS: Remove pr_<level> uses of KERN_<level>
MIPS: PNX8550: Sort out machine halt, restart and powerdown functions.
MIPS: GIC: Remove dependencies from Malta files.
MIPS: Kconfig: Fix and clarify kconfig help text for VSMP and SMTC.
MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.
MIPS: Audit: Fix hang in entry.S.
MIPS: Document why RELOC_HIDE is there.
MIPS: Octeon: Determine if helper needs to be built
MIPS: Use generic atomic64 for 32-bit kernels
MIPS: RM7000: Symbol should be static
MIPS: kspd: Adjust confusing if indentation
MIPS: Fix a typo.
SH-3 lacks an MMUCR_TI definition for global TLB flushes. As SH-3 parts
lack a split TLB, the same global flush behaviour is accomplished
through the flush bit, which just happens to be the same as on SH-4.
This fixes up the build for all SH-3 MMU parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: do not initialize PV timers on HVM if !xen_have_vector_callback
xen: do not set xenstored_ready before xenbus_probe on hvm
Configure the smc91x ethernet chip on the qsd8x50 SURF.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add gpiomux get and put calls to msmgpio request and free,
in order to allow gpio lines to be properly reference-counted
and power-managed.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Install a gpiolib driver supporting the on-chip gpios for
single-core MSMs in the 7x00 family, including 7x00A, 7x25, 7x27,
7x30, 8x50, and 8x50a.
As part of the ongoing effort to converge on a common code base,
this driver is based on the Google-Android msmgpio driver, whose
authors include Brian Swetland and Arve Hjønnevåg.
Cc: Arve Hjønnevåg <arve@android.com>
Cc: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Featurize gpiomux so that systems like 7x00 which do not wish to use it
do not have to be saddled with the configuration tables.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Now that all supported gpio_tlmm_config-using boards
are using gpiomux, remove the deprecated code.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Change the gpio-init code from deprecated gpio_tlmm_config
to the new gpiomux api.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add the 'gpiomux' api, which addresses the following shortcomings
of existing tlmm api:
- gpio power-collapse, which is managed by a peripheral processor on
other targets, must be managed by the application processor on the 8x60.
- The enable/disable flag of the legacy gpio_tlmm_config api
is not applicable on the 8x60, and causes confusion.
- The gpio 'direction' bits are meaningless for all func_sel
configurations except for generic-gpio mode (func_sel 0), in which
case the gpio_direction_* functions should be used. Having these
bits in the tlmm api leads to confusion and misuse of the gpiolib
api, and they have been removed in gpiomux.
- The functional api of the legacy system ran contrary to the typical
use-case, which is a single massive configuration at boot. Rather
than forcing hundreds of 'config' function calls, the new api
allows data to be configured with a single table.
gpiomux_get and gpiomux_put are meant to be called automatically
when gpio_request and gpio_free are called, giving automatic
gpiomux/tlmm control to those drivers/lines with simple
power profiles - in the simplest cases, an entry in the gpiomux table
and the correct usage of gpiolib is all that is required to get proper
gpio power control.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Masking in the ack callback fails to work with handle_percpu_irq and handle_edge_irq.
The interrupt stays disabled after the first invocation since percpu and edge irq do
not unmask an interrupt after handling it. For handle_level_irq masking in the ack
is redundant because ack is always called after mask in the mask_ack function.
Masking in the ack function is required only when __do_IRQ was used instead of flow
handlers, but using __do_IRQ has been deprecated.
Remove the masking of interrupt from the ack callback.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Fix a compile breakage, caused by my own careless copy-paste.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
