Add a sysdev for DBDMA PM.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use a sysdev to implement PM methods for the Au1000 interrupt controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Clean out stray unused board_reset() calls in pb1x boards, the PB1000 is
different from the rest and gets private methods.
(Cleanup after 32fd6901a6)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1085/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (92 commits)
powerpc: Remove unused 'protect4gb' boot parameter
powerpc: Build-in e1000e for pseries & ppc64_defconfig
powerpc/pseries: Make request_ras_irqs() available to other pseries code
powerpc/numa: Use ibm,architecture-vec-5 to detect form 1 affinity
powerpc/numa: Set a smaller value for RECLAIM_DISTANCE to enable zone reclaim
powerpc: Use smt_snooze_delay=-1 to always busy loop
powerpc: Remove check of ibm,smt-snooze-delay OF property
powerpc/kdump: Fix race in kdump shutdown
powerpc/kexec: Fix race in kexec shutdown
powerpc/kexec: Speedup kexec hash PTE tear down
powerpc/pseries: Add hcall to read 4 ptes at a time in real mode
powerpc: Use more accurate limit for first segment memory allocations
powerpc/kdump: Use chip->shutdown to disable IRQs
powerpc/kdump: CPUs assume the context of the oopsing CPU
powerpc/crashdump: Do not fail on NULL pointer dereferencing
powerpc/eeh: Fix oops when probing in early boot
powerpc/pci: Check devices status property when scanning OF tree
powerpc/vio: Switch VIO Bus PM to use generic helpers
powerpc: Avoid bad relocations in iSeries code
powerpc: Use common cpu_die (fixes SMP+SUSPEND build)
...
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
* 'dbg-early-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
echi-dbgp: Add kernel debugger support for the usb debug port
earlyprintk,vga,kdb: Fix \b and \r for earlyprintk=vga with kdb
kgdboc: Add ekgdboc for early use of the kernel debugger
x86,early dr regs,kgdb: Allow kernel debugger early dr register access
x86,kgdb: Implement early hardware breakpoint debugging
x86, kgdb, init: Add early and late debug states
x86, kgdb: early trap init for early debug
* 'kdb-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: (25 commits)
kdb,debug_core: Allow the debug core to receive a panic notification
MAINTAINERS: update kgdb, kdb, and debug_core info
debug_core,kdb: Allow the debug core to process a recursive debug entry
printk,kdb: capture printk() when in kdb shell
kgdboc,kdb: Allow kdb to work on a non open console port
kgdb: Add the ability to schedule a breakpoint via a tasklet
mips,kgdb: kdb low level trap catch and stack trace
powerpc,kgdb: Introduce low level trap catching
x86,kgdb: Add low level debug hook
kgdb: remove post_primary_code references
kgdb,docs: Update the kgdb docs to include kdb
kgdboc,keyboard: Keyboard driver for kdb with kgdb
kgdb: gdb "monitor" -> kdb passthrough
sparc,sunzilog: Add console polling support for sunzilog serial driver
sh,sh-sci: Use NO_POLL_CHAR in the SCIF polled console code
kgdb,8250,pl011: Return immediately from console poll
kgdb: core changes to support kdb
kdb: core for kgdb back end (2 of 2)
kdb: core for kgdb back end (1 of 2)
kgdb,blackfin: Add in kgdb_arch_set_pc for blackfin
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits)
omap4: Add support for i2c init
omap: Fix i2c platform init code for omap4
OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y
OMAP powerdomain, hwmod, omap_device: add some credits
OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains
OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate
OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains
OMAP: timers: Fix clock source names for OMAP4
OMAP4 clock: Support clk_set_parent
OMAP4: PRCM: Add offset defines for all CM registers
OMAP4: PRCM: Add offset defines for all PRM registers
OMAP4: PRCM: Remove duplicate definition of base addresses
OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention
OMAP4: CM: Remove non-functional registers in ES1.0
OMAP: hwmod: Replace WARN by pr_warning for clockdomain check
OMAP: hwmod: Rename hwmod name for the MPU
OMAP: hwmod: Do not exit the iteration if one clock init failed
OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value
OMAP: hwmod: Fix wrong pointer iteration in oh->slaves
...
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
Newer code in mm/page_alloc.c requires this function now in arches.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Decode the vast majority of insns that appear in the trace buffer to get a
better idea of what's going on at a glance.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Print out the faulting instruction so when people send traces as part of
bug reports, we have a better idea of what is going on.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that the split traps code has moved all the verbose output to the
trace.c file, we can unify all the CONFIG_DEBUG_VERBOSE handling. This
gets rid of much of the crappy ifdef forest and enables usage of normal
pr_xxx functions so checkpatch stops complaining.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current kernel/traps.c file has grown a bit unwieldy as more debugging
functionality has been added over time, so split it up into more logical
files. There should be no functional changes here, just minor whitespace
tweaking. This should make future extensions easier to manage.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch removes a custom GPIO wakeup API which allowed GPIOs to act
as wakeup sources, which are not configured as Interrupts.
This API is a leftover from the time before irq_wake was established.
From now on people must use enable_irq_wake(GPIO_IRQx) and the GPIO in
question needs to be configured as Interrupt.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These boards all have the GPIO VRSEL hooked up as an active high.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that there's a common header with everything unified, drop the defines
from the global namespace. Pollution sucks.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The empty_bad_page/empty_bad_page_table pages are unused, so punt them.
The zero_page is always allocated, so push it out to the bss to speed up
the booting process a bit and pack data nicer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
I believe support was disabled due to issues with earlier versions of
the board/processor. At worst, adding the ports back into the device
tree should result in enabling ports that don't work on older systems,
so the default should be to enable them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is started as swsusp_32.S modifications, but the amount of #ifdefs
made the whole file horribly unreadable, so let's put the support into
its own separate file.
The code should be relatively easy to modify to support 44x BookEs as
well, but since I don't have any 44x to test, let's confine the code to
FSL BookE. (The only FSL-specific part so far is 'flush_dcache_L1'.)
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Most of the MSCR bit assigments are different in e500mc versus
e500, and they are now write-one-to-clear.
Some e500mc machine check conditions are made recoverable (as long as
they aren't stuck on), most notably L1 instruction cache parity errors.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Get rid of the des_s390 specific key check module and use the generic DES
weak key check instead. Also use the generic DES header and remove the
weak key check in 3DES mode, as RFC2451 mentions that the DES weak keys
are not relevant for 3DES.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
des_s390 implements support for 3DES with a 128 bit key. This mode is probably
not used anywhere, less secure than 3DES with a 192 bit key and not
implemented in the generic des version. Removing this mode seems to be low risk
and will ease maintenance of the code.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'protect4gb' boot parameter was introduced to avoid allocating dma
space acrossing 4GB boundary in 2007 (the commit
569975591c).
In 2008, the IOMMU was fixed to use the boundary_mask parameter per
device properly. So 'protect4gb' workaround was removed (the
383af9525b). But somehow I messed the
'protect4gb' boot parameter that was used to enable the
workaround.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The e1000e device is becoming more common these days, so let's just
build it in for pseries & ppc64_defconfig.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At the moment only the RAS code uses event-sources interrupts (for EPOW
events and internal errors) so request_ras_irqs() (which actually requests
the event-sources interrupts) is found in ras.c and is static.
We want to be able to use event-sources interrupts in other pseries code,
so let's rename request_ras_irqs() to request_event_sources_irqs() and
move it to event_sources.c.
This will be used in an upcoming patch that adds support for IO Event
interrupts that come through as event sources.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I've been told that the architected way to determine we are in form 1
affinity mode is by reading the ibm,architecture-vec-5 property which
mirrors the layout of the fifth vector of the ibm,client-architecture
structure.
Eventually we may want to parse the ibm,architecture-vec-5 and create
FW_FEATURE_* bits.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed /proc/sys/vm/zone_reclaim_mode was 0 on a ppc64 NUMA box. It gets
enabled via this:
/*
* If another node is sufficiently far away then it is better
* to reclaim pages in a zone before going off node.
*/
if (distance > RECLAIM_DISTANCE)
zone_reclaim_mode = 1;
Since we use the default value of 20 for REMOTE_DISTANCE and 20 for
RECLAIM_DISTANCE it never kicks in.
The local to remote bandwidth ratios can be quite large on System p
machines so it makes sense for us to reclaim clean pagecache locally before
going off node.
The patch below sets a smaller value for RECLAIM_DISTANCE and thus enables
zone reclaim.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now if we want to busy loop and not give up any time to the hypervisor
we put a very large value into smt_snooze_delay. This is sometimes useful
when running a single partition and you want to avoid any latencies due
to the hypervisor or CPU power state transitions. While this works, it's a bit
ugly - how big a number is enough now we have NO_HZ and can be idle for a very
long time.
The patch below makes smt_snooze_delay signed, and a negative value means loop
forever:
echo -1 > /sys/devices/system/cpu/cpu0/smt_snooze_delay
This change shouldn't affect the existing userspace tools (eg ppc64_cpu), but
I'm cc-ing Nathan just to be sure.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I'm not sure why we have code for parsing an ibm,smt-snooze-delay OF
property. Since we have a smt-snooze-delay= boot option and we can
also set it at runtime via sysfs, it should be safe to get rid of
this code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we are crashing, the crashing/primary CPU IPIs the secondaries to
turn off IRQs, go into real mode and wait in kexec_wait. While this
is happening, the primary tears down all the MMU maps. Unfortunately
the primary doesn't check to make sure the secondaries have entered
real mode before doing this.
On PHYP machines, the secondaries can take a long time shutting down
the IRQ controller as RTAS calls are need. These RTAS calls need to
be serialised which resilts in the secondaries contending in
lock_rtas() and hence taking a long time to shut down.
We've hit this on large POWER7 machines, where some secondaries are
still waiting in lock_rtas(), when the primary tears down the HPTEs.
This patch makes sure all secondaries are in real mode before the
primary tears down the MMU. It uses the new kexec_state entry in the
paca. It times out if the secondaries don't reach real mode after
10sec.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In kexec_prepare_cpus, the primary CPU IPIs the secondary CPUs to
kexec_smp_down(). kexec_smp_down() calls kexec_smp_wait() which sets
the hw_cpu_id() to -1. The primary does this while leaving IRQs on
which means the primary can take a timer interrupt which can lead to
the IPIing one of the secondary CPUs (say, for a scheduler re-balance)
but since the secondary CPU now has a hw_cpu_id = -1, we IPI CPU
-1... Kaboom!
We are hitting this case regularly on POWER7 machines.
There is also a second race, where the primary will tear down the MMU
mappings before knowing the secondaries have entered real mode.
Also, the secondaries are clearing out any pending IPIs before
guaranteeing that no more will be received.
This changes kexec_prepare_cpus() so that we turn off IRQs in the
primary CPU much earlier. It adds a paca flag to say that the
secondaries have entered the kexec_smp_down() IPI and turned off IRQs,
rather than overloading hw_cpu_id with -1. This new paca flag is
again used to in indicate when the secondaries has entered real mode.
It also ensures that all CPUs have their IRQs off before we clear out
any pending IPI requests (in kexec_cpu_down()) to ensure there are no
trailing IPIs left unacknowledged.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently for kexec the PTE tear down on 1TB segment systems normally
requires 3 hcalls for each PTE removal. On a machine with 32GB of
memory it can take around a minute to remove all the PTEs.
This optimises the path so that we only remove PTEs that are valid.
It also uses the read 4 PTEs at once HCALL. For the common case where
a PTEs is invalid in a 1TB segment, this turns the 3 HCALLs per PTE
down to 1 HCALL per 4 PTEs.
This gives an > 10x speedup in kexec times on PHYP, taking a 32GB
machine from around 1 minute down to a few seconds.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds plpar_pte_read_4_raw() which can be used read 4 PTEs from
PHYP at a time, while in real mode.
It also creates a new hcall9 which can be used in real mode. It's the
same as plpar_hcall9 but minus the tracing hcall statistics which may
require variables outside the RMO.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Author: Milton Miller <miltonm@bga.com>
On large machines we are running out of room below 256MB. In some cases we
only need to ensure the allocation is in the first segment, which may be
256MB or 1TB.
Add slb0_limit and use it to specify the upper limit for the irqstack and
emergency stacks.
On a large ppc64 box, this fixes a panic at boot when the crashkernel=
option is specified (previously we would run out of memory below 256MB).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I saw this in a kdump kernel:
IOMMU table initialized, virtual merging enabled
Interrupt 155954 (real) is invalid, disabling it.
Interrupt 155953 (real) is invalid, disabling it.
ie we took some spurious interrupts. default_machine_crash_shutdown tries
to disable all interrupt sources but uses chip->disable which maps to
the default action of:
static void default_disable(unsigned int irq)
{
}
If we use chip->shutdown, then we actually mask the IRQ:
static void default_shutdown(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
desc->chip->mask(irq);
desc->status |= IRQ_MASKED;
}
Not sure why we don't implement a ->disable action for xics.c, or why
default_disable doesn't mask the interrupt.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We wrap the crash_shutdown_handles[] calls with longjmp/setjmp, so if any
of them fault we can recover. The problem is we add a hook to the debugger
fault handler hook which calls longjmp unconditionally.
This first part of kdump is run before we marshall the other CPUs, so there
is a very good chance some CPU on the box is going to page fault. And when
it does it hits the longjmp code and assumes the context of the oopsing CPU.
The machine gets very confused when it has 10 CPUs all with the same stack,
all thinking they have the same CPU id. I get even more confused trying
to debug it.
The patch below adds crash_shutdown_cpu and uses it to specify which cpu is
in the protected region. Since it can only be -1 or the oopsing CPU, we don't
need to use memory barriers since it is only valid on the local CPU - no other
CPU will ever see a value that matches it's local CPU id.
Eventually we should switch the order and marshall all CPUs before doing the
crash_shutdown_handles[] calls, but that is a bigger fix.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we take an EEH error early enough, we oops:
Call Trace:
[c000000010483770] [c000000000013ee4] .show_stack+0xd8/0x218 (unreliable)
[c000000010483850] [c000000000658940] .dump_stack+0x28/0x3c
[c0000000104838d0] [c000000000057a68] .eeh_dn_check_failure+0x2b8/0x304
[c000000010483990] [c0000000000259c8] .rtas_read_config+0x120/0x168
[c000000010483a40] [c000000000025af4] .rtas_pci_read_config+0xe4/0x124
[c000000010483af0] [c00000000037af18] .pci_bus_read_config_word+0xac/0x104
[c000000010483bc0] [c0000000008fec98] .pcibios_allocate_resources+0x7c/0x220
[c000000010483c90] [c0000000008feed8] .pcibios_resource_survey+0x9c/0x418
[c000000010483d80] [c0000000008fea10] .pcibios_init+0xbc/0xf4
[c000000010483e20] [c000000000009844] .do_one_initcall+0x98/0x1d8
[c000000010483ed0] [c0000000008f0560] .kernel_init+0x228/0x2e8
[c000000010483f90] [c000000000031a08] .kernel_thread+0x54/0x70
EEH: Detected PCI bus error on device <null>
EEH: This PCI device has failed 1 times in the last hour:
EEH: location=U78A5.001.WIH8464-P1 driver= pci addr=0001:00:01.0
EEH: of node=/pci@800000020000209/usb@1
EEH: PCI device/vendor: 00351033
EEH: PCI cmd/status register: 12100146
Unable to handle kernel paging request for data at address 0x00000468
Oops: Kernel access of bad area, sig: 11 [#1]
....
NIP [c000000000057610] .rtas_set_slot_reset+0x38/0x10c
LR [c000000000058724] .eeh_reset_device+0x5c/0x124
Call Trace:
[c00000000bc6bd00] [c00000000005a0e0] .pcibios_remove_pci_devices+0x7c/0xb0 (unreliable)
[c00000000bc6bd90] [c000000000058724] .eeh_reset_device+0x5c/0x124
[c00000000bc6be40] [c0000000000589c0] .handle_eeh_events+0x1d4/0x39c
[c00000000bc6bf00] [c000000000059124] .eeh_event_handler+0xf0/0x188
[c00000000bc6bf90] [c000000000031a08] .kernel_thread+0x54/0x70
We called rtas_set_slot_reset while scanning the bus and before the pci_dn
to pcidev mapping has been created. Since we only need the pcidev to work
out the type of reset and that only gets set after the module for the
device loads, lets just do a hot reset if the pcidev is NULL.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We ran into an issue where it looks like we're not properly ignoring a
pci device with a non-good status property when we walk the device tree
and instanciate the Linux side PCI devices.
However, the EEH init code does look for the property and disables EEH
on these devices. This leaves us in an inconsistent where we are poking
at a supposedly bad piece of hardware and RTAS will block our config
cycles because EEH isn't enabled anyway.
Signed-of-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Switch to use the generic power management helpers.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Subrata Modak reported that building a CONFIG_RELOCATABLE kernel with
CONFIG_ISERIES enabled gives the following warnings:
WARNING: 4 bad relocations
c00000000007216e R_PPC64_ADDR16_HIGHEST __ksymtab+0x00000000009dcec8
c000000000072172 R_PPC64_ADDR16_HIGHER __ksymtab+0x00000000009dcec8
c00000000007217a R_PPC64_ADDR16_HI __ksymtab+0x00000000009dcec8
c00000000007217e R_PPC64_ADDR16_LO __ksymtab+0x00000000009dcec8
The reason is that decrementer_iSeries_masked is using
LOAD_REG_IMMEDIATE to get the address of a kernel symbol, which
creates relocations that aren't handled by the kernel relocator code.
Instead of reading the tb_ticks_per_jiffy variable, we can just set
the decrementer to its maximum value (0x7fffffff) and that will work
just as well. In fact timer_interrupt sets the decrementer to that
value initially anyway, and we are sure to get into timer_interrupt
once interrupts are reenabled because we store 1 to the decrementer
interrupt flag in the lppaca (LPPACADECRINT(r12) here).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Configuring a powerpc 32 bit kernel for both SMP and SUSPEND turns on
CPU_HOTPLUG to enable disable_nonboot_cpus to be called by the common
suspend code. Previously the definition of cpu_die for ppc32 was in
the powermac platform code, causing it to be undefined if that platform
as not selected.
arch/powerpc/kernel/built-in.o: In function 'cpu_idle':
arch/powerpc/kernel/idle.c:98: undefined reference to 'cpu_die'
Move the code from setup_64 to smp.c and rename the power mac
versions to their specific names.
Note that this does not setup the cpu_die pointers in either
smp_ops (request a given cpu die) or ppc_md (make this cpu die),
for other platforms but there are generic versions in smp.c.
Reported-by: Matt Sealey <matt@genesi-usa.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc strncmp implementation does not correctly handle a zero
length, despite the claim in 0119536cd3
(Add hand-coded assembly strcmp).
Additionally, all the length arguments are size_t, not int, so use
PPC_LCMPI and eq instead of cmpwi and le throughout.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There appear to be Pegasos systems which have the rtas-event-scan
RTAS tokens, but on which the event scan always fails. They also
have an event-scan-rate property containing 0, which means call
event scan 0 times per minute.
So interpret a scan rate of 0 to mean don't scan at all. This fixes
the problem on the Pegasos machines and makes sense as well.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
