arch/arm/plat-omap/gpio.c: In function '_omap_gpio_init':
arch/arm/plat-omap/gpio.c:1492: error: 'omap_mpuio_device' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When I switched sparc64 over to the generic helpers for
smp_call_function(), I didn't convert the dinky call_lock
we had.
Use ipi_call_lock() and ipi_call_unlock().
Signed-off-by: David S. Miller <davem@davemloft.net>
The device nodes that sit above 'esp' and 'le' on SBUS lack a 'ranges'
property, but we should pass the translation up to the parent node so
that the SBUS level ranges get applied.
Based upon a bug report from Robert Reif.
Signed-off-by: David S. Miller <davem@davemloft.net>
Larry Finger reported at http://lkml.org/lkml/2008/9/1/90:
An ancient laptop of mine started throwing errors from b43legacy when
I started using 2.6.27 on it. This has been bisected to commit bfc0f59
"x86: merge tsc calibration".
The unification of the TSC code adopted mostly the 64bit code, which
prefers PMTIMER/HPET over the PIT calibration.
Larrys system has an AMD K6 CPU. Such systems are known to have
PMTIMER incarnations which run at double speed. This results in a
miscalibration of the TSC by factor 0.5. So the resulting calibrated
CPU/TSC speed is half of the real CPU speed, which means that the TSC
based delay loop will run half the time it should run. That might
explain why the b43legacy driver went berserk.
On the other hand we know about systems, where the PIT based
calibration results in random crap due to heavy SMI/SMM
disturbance. On those systems the PMTIMER/HPET based calibration logic
with SMI detection shows better results.
According to Alok also virtualized systems suffer from the PIT
calibration method.
The solution is to use a more wreckage aware aproach than the current
either/or decision.
1) reimplement the retry loop which was dropped from the 32bit code
during the merge. It repeats the calibration and selects the lowest
frequency value as this is probably the closest estimate to the real
frequency
2) Monitor the delta of the TSC values in the delay loop which waits
for the PIT counter to reach zero. If the maximum value is
significantly different from the minimum, then we have a pretty safe
indicator that the loop was disturbed by an SMI.
3) keep the pmtimer/hpet reference as a backup solution for systems
where the SMI disturbance is a permanent point of failure for PIT
based calibration
4) do the loop iteration for both methods, record the lowest value and
decide after all iterations finished.
5) Set a clear preference to PIT based calibration when the result
makes sense.
The implementation does the reference calibration based on
HPET/PMTIMER around the delay, which is necessary for the PIT anyway,
but keeps separate TSC values to ensure the "independency" of the
resulting calibration values.
Tested on various 32bit/64bit machines including Geode 266Mhz, AMD K6
(affected machine with a double speed pmtimer which I grabbed out of
the dump), Pentium class machines and AMD/Intel 64 bit boxen.
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix operator precedence bug in atari_keyb_init, which caused a failure on CT60
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A parisc allmodconfig build produces this:
arch/parisc/hpux/fs.c:107: error: 'buffer' undeclared (first use in this function)
Introduced by commit da574983de ("[PATCH]
fix hpux_getdents()").
Helge Dille also reported this in bugzilla 11461:
http://bugzilla.kernel.org/show_bug.cgi?id=11461
and he posted an identical patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: setup_valid_addr_bitmap_from_pavail() should be __init
sparc: Fix resource flags for PCI children in OF device tree.
sparc32: Implement smp_call_function_single().
Breaking lines due to some imaginary problem with a long line length is
often stupid and wrong, but never more so when it splits a string that
is printed out into multiple lines. This really ended up making it much
harder to find where some error strings were printed out, because a
simple 'grep' didn't work.
I'm sure there is tons more of this particular idiocy hiding in other
places, but this particular case hit me once more last week. So fix it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The declaration of total_memory removed. Now including <mm/mmu_decl.h>
instead. Since total_memory is a phys_addr_t which is 64-bit on 44x and
is_power_of_2() works with u32 so I just inlined (size & (size-1)) != 0
instead.
Also this patch fixes default initialization: res->end should be 0x7fffffff
not 0x80000000.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch moves some attributes out from the platform data into the
dynamically created nand device. This results into a cleaner interface
and allows to use constant pxa3xx_nand_flash definitions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch marks some attributes as 'const' which are set only once and
never be modified by the driver. There are some changes in parameter
list and variable declarations too which mark them as 'const'.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 'flash' and 'num_flash' attributes to the platform data.
There was added code in the driver to iterate across these attributes in the
detect-flash routine. This is done similarly to the existing method
which uses a 'builtin_flash_types' field.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves the exported datastructures from the pxa3xx_nand.c driver
into the <mach/pxa3xx_nand.h> header. This is a plain movement without
any modification of the attributes.
This is the first one of a set of patches which:
* allows to specify used NAND flash in the platform code and allows to turn
off the old way to specify NAND characteristics in the driver. This way did
not worked well as these characteristics depend on the platform and can not be
derived from NAND id alone.
E.g. some NAND chips share the same ID (e.g. K9K8G08U0A and K9NBG08U5A) but
have different timings (which are written in the common driver currently and
must be modified there).
* adds 'const' annotations at various places
Further patches will be sent to the mtd-list.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allow PXA IRQs to be numbered starting at 16, leaving 0 to 15 for the
ISA IRQs, if needed.
This patch depends on RMK's PXA_HAVE_BOARD_IRQS patch.
Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>
Acked-by: Russel King <linux@arm.linux.org.uk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the other assembly functions do not seem to save the frame
pointer onto the stack, this patch changes the csum_partial_copy_*
functions to behave in the same way.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The post-index immediate value is optional if it is 0 and this patch
removes it. The reason is to allow such instructions to compile to
Thumb-2 where only pre-indexed LDRT/STRT instructions are allowed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The last strnebt instruction has a post-index of 1 but the address
register is set to 0 in the next instruction, so no need for
post-indexing.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This declaration specifies the "function" type and size for various
assembly functions, mainly needed for generating the correct branch
instructions in Thumb-2.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a config option (CONFIG_VMSPLIT_*) to allow choosing
between 3:1, 2:2 and 1:3 user:kernel memory splits.
Tested-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CONFIG_DEBUG_BUGVERBOSE is not set, we get warnings such as:
arch/arm/mm/ioremap.c: In function ‘remap_area_pte’:
arch/arm/mm/ioremap.c:67: warning: control reaches end of non-void function
mm/bootmem.c: In function ‘mark_bootmem’:
mm/bootmem.c:321: warning: control reaches end of non-void function
fs/dcache.c: In function ‘d_materialise_unique’:
fs/dcache.c:1875: warning: control reaches end of non-void function
fs/nfs/client.c: In function ‘nfs_sockaddr_match_ipaddr’:
fs/nfs/client.c:251: warning: control reaches end of non-void function
block/cfq-iosched.c: In function ‘cfq_async_queue_prio’:
block/cfq-iosched.c:1501: warning: control reaches end of non-void function
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linux/ARM currently doesn't support robust or PI futexes.
The problem is that the kernel wants to perform certain ops
(cmpxchg, set, add, or, andn, xor) atomically on user-space
addresses, and ARM's futex.h doesn't support that.
This patch adds that support, but only for uniprocessor machines.
For UP it's enough to disable preemption to ensure mutual exclusion
with other software agents (futexes don't need to care about other
hardware agents, fortunately).
This patch is based on one posted by Khem Raj on 2007-08-01
<http://marc.info/?l=linux-arm-kernel&m=118599407413016&w=2>.
(That patch is included in the -RT kernel patches.)
My changes since that version include:
* corrected implementation of FUTEX_OP_ANDN (must complement oparg)
* added missing memory clobber to futex_atomic_cmpxchg_inatomic()
* removed spinlock because it's unnecessary for UP and insufficient
for SMP, instead the code is restricted to UP and relies on the
fact that pagefault_disable() also disables preemption
* coding style cleanups
Tested on ARMv5 XScales with the glibc-2.6 nptl test suite.
Tested-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in commit 796969104c,
and because of commit b03a5b7559,
the direct calling of kprobe_trap_handler() can be removed.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Oprofile kernel support for ARMv7.
Tested on OMAP3430 and OMAP3530 chipsets (Cortex-A8).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than pollute asm/cacheflush.h with the cache type definitions,
move them to asm/cachetype.h, and include this new header where
necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add asm/cputype.h, moving functions and definitions from asm/system.h
there. Convert all users of 'processor_id' to the more efficient
read_cpuid_id() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The value stored into the SDRAMC LPR register should be the current
value of the register with the Self-refresh value set in the lower bit
field.
The bug involved only the Self-refresh value being written to the
register, thus over writing any low-power ram settings.
Signed-off-by: Humphrey Bucknell <hbucknell@saitek.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
When using the Java Extension Module hardware, a Java stack underflow or
overflow trap may cause the system to enter an infinite exception loop.
Although there's no kernel support for the Java hardware yet, we need to
be able to recover from this situation and keep the system running.
This patch adds code to detect and fixup this situation in the critical
exception handler and terminate the faulting process. We may have to
rethink how to handle this more gracefully when the necessary kernel
support for hardware-accelerated Java is added.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This mirrors the of_device_id[] changes done in
fd098316ef ("sparc: Annotate
of_device_id arrays with const or __initdata.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Three main things:
1) Make prober an arch initcall instead of using hard-coded invocation
from paging_init()
2) Shrink table size, the fpu ident stuff was never used.
3) Use named struct initialized in table.
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing some easy cleanups on the sparc code I noticed that the
CONFIG_SUN4 code seems to be worse than the rest - there were some
"I don't know how it should work, but the current code definitely cannot
work." places.
And while I have seen people running Linux on machines like a
SPARCstation 5 a few years ago I don't recall having seen sun4
machines, even less ones running Linux.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is now limited to just doing the basic clock board and FHC
chip initialization and registering the platform devices for the
per-board LEDs, which are driven by the new LEDS_STARFIRE driver.
The IRQ register handling is already confined purely to the device
tree code.
Signed-off-by: David S. Miller <davem@davemloft.net>