This makes the sam440ep.dts dts-v1 compliant.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.
It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch add a check to the PPC4xx PCIe driver to detect if the port
is disabled via the device-tree. This is needed for the AMCC Canyonlands
board which has an option to either select 2 PCIe ports or 1 PCIe port
and one SATA port. The SATA port and the 1st PCIe port pins are multiplexed
so we can't start both drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The "ndfc-chip" device doesn't need any resources. All resources
are handled by the "ndfc-nand" device. Registering the same memory
resource twice causes "cat /proc/iomem" to go into an infinite loop
displaying NDFC memory addresses.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add support for the NOR flash found on the AMCC Taishan Board
and enable MTD support in the defconfig.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This reverts commit acb0142bf0.
AMCC has indicated that the PPC 460GT does have FPU support. This
revert enables the FPU for those chips again.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Without simpleImage% in the BOOT_TARGETS list, it is impossible to
build any of the simpleImages.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Allows us to dump PCI space before any kernel changes have been made.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce 'struct pm_ops' and 'struct pm_ext_ops' ('ext' meaning
'extended') representing suspend and hibernation operations for bus
types, device classes, device types and device drivers.
Modify the PM core to use 'struct pm_ops' and 'struct pm_ext_ops'
objects, if defined, instead of the ->suspend(), ->resume(),
->suspend_late(), and ->resume_early() callbacks (the old callbacks
will be considered as legacy and gradually phased out).
The main purpose of doing this is to separate suspend (aka S2RAM and
standby) callbacks from hibernation callbacks in such a way that the
new callbacks won't take arguments and the semantics of each of them
will be clearly specified. This has been requested for multiple
times by many people, including Linus himself, and the reason is that
within the current scheme if ->resume() is called, for example, it's
difficult to say why it's been called (ie. is it a resume from RAM or
from hibernation or a suspend/hibernation failure etc.?).
The second purpose is to make the suspend/hibernation callbacks more
flexible so that device drivers can handle more than they can within
the current scheme. For example, some drivers may need to prevent
new children of the device from being registered before their
->suspend() callbacks are executed or they may want to carry out some
operations requiring the availability of some other devices, not
directly bound via the parent-child relationship, in order to prepare
for the execution of ->suspend(), etc.
Ultimately, we'd like to stop using the freezing of tasks for suspend
and therefore the drivers' suspend/hibernation code will have to take
care of the handling of the user space during suspend/hibernation.
That, in turn, would be difficult within the current scheme, without
the new ->prepare() and ->complete() callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Contention for scarce PCI memory resources has been growing
due to an increasing number of PCI slots in large multi-node
systems. The kernel currently attempts by default to
allocate memory for all PCI expansion ROMs so there has
also been an increasing number of PCI memory allocation
failures seen on these systems. This occurs because the
BIOS either (1) provides insufficient PCI memory resource
for all the expansion ROMs or (2) provides adequate PCI
memory resource for expansion ROMs but provides the
space in kernel unexpected BIOS assigned P2P non-prefetch
windows.
The resulting PCI memory allocation failures may be benign
when related to memory requests for expansion ROMs themselves
but in some cases they can occur when attempting to allocate
space for more critical BARs. This can happen when a successful
expansion ROM allocation request consumes memory resource
that was intended for a non-ROM BAR. We have seen this
happen during PCI hotplug of an adapter that contains a
P2P bridge where successful memory allocation for an
expansion ROM BAR on device behind the bridge consumed
memory that was intended for a non-ROM BAR on the P2P bridge.
In all cases the allocation failure messages can be very
confusing for users.
This patch provides a new 'pci=norom' kernel boot parameter
that can be used to disable the default PCI expansion ROM memory
resource allocation. This provides a way to avoid the above
described issues on systems that do not contain PCI devices
for which drivers or user-level applications depend on the
default PCI expansion ROM memory resource allocation behavior.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is very trivial patch. We're transitioning to the cpm_muram_*
calls. That's it.
Less trivial changes:
- BD_SC_* defines were defined in the cpm.h and qe.h, so to avoid redefines
we remove BD_SC from the qe.h and use cpm.h along with cpm_muram_*
prototypes;
- qe_muram_dump was unused and thus removed;
- added some code to the cpm_common.c to support legacy QE bindings
(data-only node name).
- For convenience, define qe_* calls to cpm_*. So drivers need not to be
changed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to access QE GPIOs via Linux GPIO API.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- split and export __par_io_config_pin() out of par_io_config_pin(), so we
could use the prefixed version with GPIO LIB API;
- rename struct port_regs to qe_pio_regs, and place it into qe.h;
- rename #define NUM_OF_PINS to QE_PIO_PINS, and place it into qe.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a function to the qe_lib to setup QE USB clocks routing.
To setup clocks safely, cmxgcr register needs locking, so I just reused
ucc_lock since it was used only to protect cmxgcr.
The idea behind placing clocks routing functions into the qe_lib is that
later we'll hopefully switch to the generic Linux Clock API, thus, for
example, FHCI driver may be used for QE and CPM chips without nasty #ifdefs.
This patch also fixes QE_USB_RESTART_TX command definition in the qe.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
GTM stands for General-purpose Timers Module and able to generate
timer{1,2,3,4} interrupts. These timers are used by the drivers that
need time precise interrupts (like for USB transactions scheduling for
the Freescale USB Host controller as found in some QE and CPM chips),
or these timers could be used as wakeup events from the CPU deep-sleep
mode.
Things unimplemented:
1. Cascaded (32 bit) timers (1-2, 3-4).
This is straightforward to implement when needed, two timers should
be marked as "requested" and configured as appropriate.
2. Super-cascaded (64 bit) timers (1-2-3-4).
This is also straightforward to implement when needed, all timers
should be marked as "requested" and configured as appropriate.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds local bus nodes for Flash and CAN to the DTS file
of the TQM8560 module (tqm8560.dts).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) flash
memory and therefore a modified memory map is required and setup by
the board loader. This patch adds an appropriate DTS file.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.
If not, ethernet will not work:
e0024520:03 not found
eth1: Could not attach to PHY
IP-Config: Failed to open eth1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
more unification. Should cause no change in functionality.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpuid(0x05) provides extended information about MWAIT in EDX when bit
0 of ECX is set. Bit 4-7 of EDX determine whether MWAIT is supported
for C1. C1E enabled CPUs have these bits set to 0.
Based on an earlier patch from Andi Kleen.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simplify code: no need to do a cpuid(1) again. The cpuinfo structure
has all necessary information already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the "MSR_K8_ENABLE_C1E" MSR to INT_PENDING_MSG, which is the
name in the data sheet as well. Move the C1E mask to the header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
default_idle is selected in cpu_idle(), when no other idle routine is
selected. Select it in select_idle_routine() when mwait is not
selected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All the maintained platforms are now in arch/powerpc, so the old
arch/ppc stuff can now go away.
Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: John Linn <john.linn@xilinx.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently arch/x86/kernel/pci-dma.c always adds __GFP_NORETRY
to the allocation flags, because it wants to be reasonably
sure not to deadlock when calling alloc_pages().
But really that should only be done in two cases:
- when allocating memory in the lower 16 MB DMA zone.
If there's no free memory there, waiting or OOM killing is of no use
- when optimistically trying an allocation in the DMA32 zone
when dma_mask < DMA_32BIT_MASK hoping that the allocation
happens to fall within the limits of the dma_mask
Also blindly adding __GFP_NORETRY to the the gfp variable might
not be a good idea since we then also use it when calling
dma_ops->alloc_coherent(). Clearing it might also not be a
good idea, dma_alloc_coherent()'s caller might have set it
on purpose. The gfp variable should not be clobbered.
[ mingo@elte.hu: converted to delta patch ontop of previous version. ]
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
need to call early_reserve_e820() to preallocate mptable for 32bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
a multi-socket test-system with 3 or 4 ioapics, when 4 dualcore cpus or
2 quadcore cpus installed, needs to switch to bigsmp or physflat.
CPU apic id is [4,11] instead of [0,7], and we need to check max apic
id instead of cpu numbers.
also add check for 32 bit when acpi is not compiled in or acpi=off.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
don't assume we can use RAM near the end of every node.
Esp systems that have few memory and they could have
kva address and kva RAM all below max_low_pfn.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now we are using register_e820_active_regions() instead of
add_active_range() directly. So end_pfn could be different between the
value in early_node_map to node_end_pfn.
So we need to make shrink_active_range() smarter.
shrink_active_range() is a generic MM function in mm/page_alloc.c but
it is only used on 32-bit x86. Should we move it back to some file in
arch/x86?
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The first argument to __ctl_store() should be the array to store
stuff in, not just the first element of that array. With the
current code in __cpu_up(), mainline GCC dies with an internal
compiler error. I didn't diagnose that further, but just fixed
the kernel bug.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
If a memory range is supposed to be added to the 1:1 mapping and it
ends just below the maximum supported physical address it won't
succeed. This is because a test doesn't consider that the end address
is 1 smaller than start + size.
Fix the comparison.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of !64BIT kernel we end up with a zero sized mem_section array.
This happens because NR_MEM_SECTIONS is smaller than SECTIONS_PER_ROOT
but we have:
#define NR_SECTION_ROOTS (NR_MEM_SECTIONS / SECTIONS_PER_ROOT)
and
struct mem_section *mem_section[NR_SECTION_ROOTS];
So fix this by selecting SPARSEMEM_STATIC which makes sure
that SECTIONS_PER_ROOT is 1.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin serial driver: fix up tty core set_ldisc API change breakage bug
Blackfin arch: protect only the SPI bus controller with CONFIG_SPI_BFIN
Blackfin arch: fixup warnings with the new cplb saved values
Blackfin Serial Driver: Clean up BF54x macro in blackfin UART driver.
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] ehea: Remove dependency on MEMORY_HOTPLUG
[POWERPC] Make walk_memory_resource available with MEMORY_HOTPLUG=n
[POWERPC] Use dev_set_name in pci_64.c
[POWERPC] Fix incorrect enabling of VMX when building signal or user context
[POWERPC] boot/Makefile CONFIG_ variable fixes
Update the defconfig for the Freescale MPC8610 HPCD board. Enable module
support. Disable support for all NICs except for the on-board ULI526x.
Enable support for the Freescale DIU driver. Increase the maximum zone order
to 12, so that the DIU driver can allocate physically-contiguous 5MB buffers.
Enable SYSV IPC and OSS plugin support, which are needed for some OSS apps.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>