This is prerequisite for enabling the sub-device node.
The control handler is now initialized in driver's probe callback
in order to allow the user space access controls before the device
power is enabled with s_power. This is needed due to s_power being
currently called only by the host driver.
It also adds the subdev internal operations, only open() for now
for the TRY format initialization.
Acked-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_ctrl_handler_setup() may fail so check its return value when
restoring controls after device is powered on. While at it simplify
the m5mols_restore_function() a bit.
Acked-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the v4l2_device notifications id to S5P_FIMC_TX_END_NOTIFY.
Moreover, when frame capture fails, send an 'end of frame' notification
with size set to 0 to let the host driver return a buffer back to the
user and prevent applications waiting forever on DQBUF.
The notification is needed only for the s5p-fimc driver.
Acked-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improve the single frame capture set up sequence. Since there is
no need to re-enable the interrupts in each capture sequence, unmask
the required interrupts once at the device initialization time.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The M-5MOLS internal controller's initialization time depends on the
hardware and firmware revision. Currently the driver just waits for
worst case time period, after applying the voltage supplies, for
the device to be ready. The M-5MOLS supports "System initialization"
interrupt which is triggered after the controller finished booting.
So use this interrupt to optimize the initialization sequence.
After the voltage supplies are applied the I2C communication will
fail, until the internal controller initializes to Flash Writer
state. For the period when the I2C is not accessible use the
isp_ready flag to suppress the error logs.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to keep this in the drivers' private data structure,
an on the stack variable is enough. Also simplify a bit the ISP state
switching function.
Acked-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The work struct based interrupt handling is not flexible enough
as the M-5MOLS control sequence involves I2C access sequences
before and after an interrupt is generated. A single waitqueue is
enough for the job so remove the work struct based code.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make m5mols_busy_wait function jiffies based rather than relying
on some fixed number of I2C read iterations while busy waiting
for the device to execute a request. With fixed number of iterations
we may be getting different wait times, depending on the I2C speed.
In some conditions we have to wait even if the I2C communications
fails, in those cases M5MOLS_I2C_RDY_WAIT_MASK should be passed
as the mask argument to m5mols_busy_wait().
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The redundant definitions of the m5mols I2C register addresses within
the pages (categories) are removed. In place of symbolic definitions
plain numbers are used which simplifies the code and eases identifying
the registers in the documentation.
Also make the m5mols_busy() function accept I2C_REG() value as a register
address, like all other functions, rather than using the category and
command values.
Acked-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Exynos SoCs the FIMC IP allows to configure globally the alpha
component of all pixels for V4L2_PIX_FMT_RGB32, V4L2_PIX_FMT_RGB555
and V4L2_PIX_FMT_RGB444 image formats. This patch adds a v4l2 control
in order to let the applications control the alpha component value.
The alpha value range depends on the pixel format, for RGB32 it's
0..255 (8-bits), for RGB555 - 0..1 (1-bit) and for RGB444 - 0..15
(4-bits). The v4l2 control range is always 0..255 and the alpha
component data width is determined by currently set format on the
V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE buffer queue. The applications
need to match the alpha channel value range and the pixel format
since the driver will clamp the alpha component. Depending on
fourcc the valid alpha bits are:
- V4L2_PIX_FMT_RGB555 [0]
- V4L2_PIX_FMT_RGB444 [3:0]
- V4L2_PIX_FMT_RGB32 [7:0]
When switching to a pixel format with smaller alpha component width
the currently set alpha value will be clamped to maximum value valid
for current format. When switching to a format with wider alpha the
alpha value remains unchanged.
The variant description data structure is extended with a new entry
so an additional control is created only where really supported by
the hardware.
V4L2_PIX_FMT_RGB555 and V4L2_PIX_FMT_RGB444 formats are only valid
for V4L2_BUF_TYPE_VIDEO_CAPTURE buffer queue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_ALPHA_COMPONENT control is intended for the video capture
or memory-to-memory devices that are capable of setting up the per-pixel
alpha component to some arbitrary value. It allows to set the alpha
component for all pixels to an arbitrary value.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linux 3.2-rc7
* tag 'v3.2-rc7': (1304 commits)
Linux 3.2-rc7
netfilter: xt_connbytes: handle negation correctly
Btrfs: call d_instantiate after all ops are setup
Btrfs: fix worker lock misuse in find_worker
net: relax rcvbuf limits
rps: fix insufficient bounds checking in store_rps_dev_flow_table_cnt()
net: introduce DST_NOPEER dst flag
mqprio: Avoid panic if no options are provided
bridge: provide a mtu() method for fake_dst_ops
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
sparc64: Fix MSIQ HV call ordering in pci_sun4v_msiq_build_irq().
pata_of_platform: Add missing CONFIG_OF_IRQ dependency.
ipv4: using prefetch requires including prefetch.h
VFS: Fix race between CPU hotplug and lglocks
vfs: __read_cache_page should use gfp argument rather than GFP_KERNEL
USB: Fix usb/isp1760 build on sparc
net: Add a flow_cache_flush_deferred function
...
Conflicts:
drivers/media/common/tuners/tda18218.c
drivers/media/video/omap3isp/ispccdc.c
drivers/staging/media/as102/as102_drv.h
When runtime power management is enabled put the Samsung keypad driver
into suspend mode with wakeups disabled whenever the device is open but
a key is not actually been pressed. As well as saving a trivial amount of
power this will support the use of SoC wide idle modes which put the entire
device into a retention mode and use explicit wakeup sources to exit.
Since not all of the interrupt controllers used with the driver support
set_irq_wake() (though they all do the right thing) and there's a nasty
WARN() when we disable wake after failing to enable it keep track of the
current wake status from runtime PM and only disable wake if we managed
to enable it; I'm not entirely sure why this doesn't affect the existing
uses of the API in the driver.
System suspend is unaffected as the driver core will runtime resume any
suspended devices prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
drivers/input/keyboard/samsung-keypad.c
This adds a simple device tree binding to the tegra keyboard controller.
Also, mark the default keymap as __devinitdata since it is not referenced
after boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert mc13892-regulator driver to use devm_kzalloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We still don't use rdrand in /dev/random, which just seems stupid. We
accept the *cycle*counter* as a random input, but we don't accept
rdrand? That's just broken.
Sure, people can do things in user space (write to /dev/random, use
rdrand in addition to /dev/random themselves etc etc), but that
*still* seems to be a particularly stupid reason for saying "we
shouldn't bother to try to do better in /dev/random".
And even if somebody really doesn't trust rdrand as a source of random
bytes, it seems singularly stupid to trust the cycle counter *more*.
So I'd suggest the attached patch. I'm not going to even bother
arguing that we should add more bits to the entropy estimate, because
that's not the point - I don't care if /dev/random fills up slowly or
not, I think it's just stupid to not use the bits we can get from
rdrand and mix them into the strong randomness pool.
Link: http://lkml.kernel.org/r/CA%2B55aFwn59N1=m651QAyTy-1gO1noGbK18zwKDwvwqnravA84A@mail.gmail.com
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.
Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 & vicam
cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael S. Tsirkin also noticed that we could run the refill work
multiple CPUs: if we kick off a refill on one CPU and then on another,
they would both manipulate the queue at the same time (they use
napi_disable to avoid racing against the receive handler itself).
Tejun points out that this is what the WQ_NON_REENTRANT flag is for,
and that there is a convenient system kthread we can use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin noticed that we could run the refill work after
ndo_close, which can re-enable napi - we don't disable it until
virtnet_remove. This is clearly wrong, so move the workqueue control
to ndo_open and ndo_stop (aka. virtnet_open and virtnet_close).
One subtle point: virtnet_probe() could simply fail if it couldn't
allocate a receive buffer, but that's less polite in virtnet_open() so
we schedule a refill as we do in the normal receive path if we run out
of memory.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment VFs can only operate in Eth mode.
In addition we don't want the VF to attempt link sensing,
so we block this option as well.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mc13783-regulator driver to use devm_kzalloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixing wrong register offset which is used to retrieve the number of buttons
attached to the hardware.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In the case of create_regulator() fails, goto the error path immediately.
It does not make sense to update rdev->open_count if create_regulator fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is hdmi display support for exynos drm driver.
There is already v4l2 based exynos hdmi driver in drivers/media/video/s5p-tv
and some low level code is already in s5p-tv and even headers for register
define are almost same. but in this patch, we decide not to consider separated
common code with s5p-tv.
Exynos HDMI is composed of 5 blocks, mixer, vp, hdmi, hdmiphy and ddc.
1. mixer. The piece of hardware responsible for mixing and blending multiple
data inputs before passing it to an output device. The mixer is capable of
handling up to three image layers. One is the output of VP. Other two are
images in RGB format. The blending factor, and layers' priority are controlled
by mixer's registers. The output is passed to HDMI.
2. vp (video processor). It is used for processing of NV12/NV21 data. An image
stored in RAM is accessed by DMA. The output in YCbCr444 format is send to
mixer.
3. hdmi. The piece of HW responsible for generation of HDMI packets. It takes
pixel data from mixer and transforms it into data frames. The output is send
to HDMIPHY interface.
4. hdmiphy. Physical interface for HDMI. Its duties are sending HDMI packets to
HDMI connector. Basically, it contains a PLL that produces source clock for
mixer, vp and hdmi.
5. ddc (display data channel). It is dedicated i2c channel to exchange display
information as edid with display monitor.
With plane support, exynos hdmi driver fully supports two mixer layes and vp
layer. Also vp layer supports multi buffer plane pixel formats having non
contigus memory spaces.
In exynos drm driver, common drm_hdmi driver to interface with drm framework
has opertion pointers for mixer and hdmi. this drm_hdmi driver is registered as
sub driver of exynos_drm. hdmi has hdmiphy and ddc i2c clients and controls
them. mixer controls all overlay layers in both mixer and vp.
Vblank interrupts for hdmi are handled by mixer internally because drm
framework cannot support multiple irq id. And pipe number is used to check
which display device irq happens.
History
v2: this version
- drm plane feature support to handle overlay layers.
- multi buffer plane pixel format support for vp layer.
- vp layer support
RFCv1: original
- at https://lkml.org/lkml/2011/11/4/164
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
some platform could be entering to sleep after short time once lcd panel off
but before that vblank could be off by vblank off delay feature. at that time,
vblank doesn't have the pair between vblank_get/put. so this path makes vblank
off delay to have enough.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
These formats(NV12M, NV12MT and YUV420M) have non contiguous multi
planes, so each plane uses different buffer. The exynos drm should
support multi buffer for them.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The fbdev fb and the user fb is created from same function -
exynos_drm_fb_create, but this function creates not only drm framebuffer
but buffer of fbdev. Remove it because it complicates codes and use
exynos_drm_gem_create() than exynos_drm_buf_create() to create buffer of
fbdev, it give better consistency of codes and more clear
implementation.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
exynos_drm_gem_create function created gem object with gem handle but it
can be called externally without gem handle creation through this patch.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Make a fake mmap offset only when it needs.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This cleans codes of exynos gem - indents and order function and so on.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
On extensive NFS boots on a mx6qsabrelite board it was noted that "FEC: MDIO read timeout" were occuring,
which caused failure on loading the FEC driver.
The original FEC_MII_TIMEOUT was set to 1 ms, which is too low when passed to the usecs_to_jiffies macro.
On ARM one jiffy is 10ms, so use a timeout of 30ms, which corresponds to 3 jiffies.
After running extensive NFS boots, the MDIO timeouts do not occur anymore with this change.
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 40d3e0f (clk: provide prepare/unprepare functions) provides
the config option HAVE_CLK_PREPARE for platforms that have
prepare/unprepare implementation to select. This patch adds the option
into drivers/clk/Kconfig, so that it can be actually selected.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
The patch converts mxs-auart driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
The patch converts flexcan driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
The patch converts mxs-mmc driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The patch converts mxs-dma driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
It's for migrating to generic clk framework API.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
* drivers/rtc-sa1100:
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
Since the regmap of rtc on sa1100, pxa and mmp Marvell soc families are
almost the same, so re-arch the rtc-sa1100 to support them.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In rtc generic interface of setting alarm, it will check the alarm time
value valid or not, so rtc_periodic_alarm is redundant, remove it.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>