Sun, Yunying reported the following failure on Denverton micro-server:
EDAC DEBUG: pnd2_init:
EDAC DEBUG: pnd2_probe:
EDAC DEBUG: dnv_rd_reg: Read b_cr_tolud_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_lo_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_hi_pci=00000000_00000004
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region0_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region1_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_base_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_mask_mchbar=00000000_00000000
EDAC pnd2: Failed to register device with error -19.
On Denverton micro-server, the presence of the P2SB bridge PCI device is
enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When
'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac
EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the
pnd2_edac EDAC driver failed to get BAR then reported the above failure.
Therefor, store the presence state of P2SB PCI device before unhiding it
for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There seems to be no need for separate ones since all users include both
files anyhow. Merge them because include/linux/i2c is to be deprecated.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c driver can run into driver dependency issues if its loaded
before a clock driver it depends on. Therefore, EPROBE_DEFER may be
returned by devm_clk_get and should be returned in probe to allow the
kernel to reprobe the driver at a later time. This patch allows the error
value returned by devm_clk_get to be passed through and not overwritten.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT7622. Compare to MT8173 i2c controller,
MT7622 limits message numbers to 255, and does not support 4GB
DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Cherry Trail Whiskey Cove PMIC's IRQ line is attached to one of
the GPIOs of the Cherry Trail SoC. The CHT GPIO controller sometimes
fails to deliver IRQs (seen when there is an IRQ storm on another pin).
This commit works around this by reducing the long timeout which was
a poor attempt to workaround this from 3s to 30ms and after that
manually checking the status register for transfer completion by
calling the threaded IRQ handler directly.
This is safe todo as the entire threaded IRQ handler is protected
by a mutex.
Note 30ms should be more then long enough, at 100KHz any smbus single
byte transaction should be finished in 4ms.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Testing has shown that writing 1 to clear the read-complete irq does
not work until the data register has been read first.
This commit fixes the driver to read the data register first, halving the
amount of interrupts in most cases since we mostly read on this i2c bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although unlikely without locking the smbux_xfer function may miss
the nack flag and further fixes in this patch-set add some more
complex constructions which need protection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If i2c_mux_alloc() fails then we'd have a NULL dereference here.
Fixes: c4aee3e1b0 ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
24xx BMCs have larger clock divider granularity which can cause problems
when trying to set them as 25xx clock dividers; this adds clock setting
code specific to 24xx.
This also fixes a potential issue where clock dividers were rounded down
instead of up.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-i2c@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No platform (at least no upstreamed platform) has ever used this
platform_data. Just drop it and simplify the code.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.
This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.
Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Support for the i2c controller on rv1108 soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Check for i2c_algorithm and i2c_adapter_quirks structures that are only
stored in the algo and quirks fields of an i2c_adapter structure
correspondingly. These fields are declared const, so i2c_algorithm and
i2c_adapter_quirks structures that have this property can be declared
as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for designware)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix loop preventing some platforms from waking up via the power
button in s2idle.
intel-vbtn:
- match power button on press rather than release
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZhjtgAAoJEKbMaAwKp3647u4IALEnsRt10hj2ognbpQUPxqzB
uwjlQ7ukqwWVbpgElQ6q2hKUFHNnk2CGuzIEjvRKpme0UpsSPUQRPZGeUGDmvC3l
cOxNSmyTJkmeCEU9G7yj1NrcaOEFQ9iRLrZmSRnYBSWBgjzYdpfC/xog2y8mVkgO
FQAU2ul9Ph5eXEOTQBw56LtzsraJtBdV76aKESuJEAw3h0E8svhLeV43caVic/Go
Yv9aRZRkj/5oQHwXe+GC5K4dFdWFYZ9iGLQFHgcICRACcUq7p0ysVvf8YMVQplyR
Xm2j8Dq1ierId5g90p5fznIM4BeBnIM2Iclkk4dPaIrP3Fogd9eq1gvxQKvWgpY=
=IOnZ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.
The problem happens because:
- press power button:
- system emits 0xc0 (power press), event ignored
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- set wakeup_mode to true
- system goes to s2idle
- press power button
- system emits 0xc0 (power press), wakeup_mode is true,
system wakes
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- system goes to s2idle again
To avoid this situation, process the presses (which matches what
intel-hid does too).
Verified on an Dell XPS 9365
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
-----BEGIN PGP SIGNATURE-----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=wQ04
-----END PGP SIGNATURE-----
Merge tag 'media/v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"This series is larger than I would like to submit for -rc4. My
original intent were to sent it to either -rc2 or -rc3. Unfortunately,
due to my vacations, I got a lot of pending stuff after my return, and
had to do some biz trips, with prevented me to send this earlier.
Several fixes:
- some fixes at atomisp staging driver
- several gcc 7 warning fixes
- cleanup media SVG files, in order to fix PDF build on some distros
- fix random Kconfig build of venus driver
- some fixes for the venus driver
- some changes from semaphone to mutex in ngene's driver
- some locking fixes at dib0700 driver
- several fixes on ngene's driver and frontends to make it properly
support some new boards added on Kernel 4.13
- some fixes to CEC drivers
- omap_vout: vrfb: convert to dmaengine
- docs-rst: document EBUSY for VIDIOC_S_FMT
Please notice that the big diffstat changes here are at the SVG files.
Visually, the images look the same, but the file size is now a lot
smaller than before, and they don't use some XML tags that would cause
them to be badly parsed by some ImageMagick versions, or to require a
lot of memory by TeTex, with would break PDF output on some
distributions"
* tag 'media/v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (68 commits)
media: atomisp2: array underflow in imx_enum_frame_size()
media: atomisp2: array underflow in ap1302_enum_frame_size()
media: atomisp2: Array underflow in atomisp_enum_input()
media: platform: davinci: drop VPFE_CMD_S_CCDC_RAW_PARAMS
media: platform: davinci: return -EINVAL for VPFE_CMD_S_CCDC_RAW_PARAMS ioctl
media: venus: don't abuse dma_alloc for non-DMA allocations
media: venus: hfi: fix error handling in hfi_sys_init_done()
media: venus: fix compile-test build on non-qcom ARM platform
media: venus: mark PM functions as __maybe_unused
media: cec-notifier: small improvements
media: pulse8-cec: persistent_config should be off by default
media: cec: cec_transmit_attempt_done: ignore CEC_TX_STATUS_MAX_RETRIES
media: staging: atomisp: array underflow in ioctl
media: lirc: LIRC_GET_REC_RESOLUTION should return microseconds
media: svg: avoid too long lines
media: svg files: simplify files
media: selection.svg: simplify the SVG file
media: vimc: set id_table for platform drivers
media: staging: atomisp: disable warnings with cc-disable-warning
media: davinci: variable 'common' set but not used
...
- LP87565: set the proper output level for direction_output.
- stm32: fix the kernel build by selecting the hierarchical
irqdomain symbol properly - this happens to be done in the
pin control framework but whatever, it had dependencies to
GPIO so we need to apply it here.
- Select the hierarchical IRQ domain also for Xgene.
- Fix wakeups to work on MXC.
- Fix up the device tree binding on Exar that went astray,
also add the right bindings.
- Fix the unwanted events for edges from the library.
- Fix the unbalanced chanined IRQ on the Tegra.
-----BEGIN PGP SIGNATURE-----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=0ZOK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- LP87565: set the proper output level for direction_output.
- stm32: fix the kernel build by selecting the hierarchical irqdomain
symbol properly - this happens to be done in the pin control
framework but whatever, it had dependencies to GPIO so we need to
apply it here.
- Select the hierarchical IRQ domain also for Xgene.
- Fix wakeups to work on MXC.
- Fix up the device tree binding on Exar that went astray, also add the
right bindings.
- Fix the unwanted events for edges from the library.
- Fix the unbalanced chanined IRQ on the Tegra.
* tag 'gpio-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra: fix unbalanced chained_irq_enter/exit
gpiolib: skip unwanted events, don't convert them to opposite edge
gpio: exar: Use correct property prefix and document bindings
gpio: gpio-mxc: Fix: higher 16 GPIOs usable as wake source
gpio: xgene-sb: select IRQ_DOMAIN_HIERARCHY
pinctrl: stm32: select IRQ_DOMAIN_HIERARCHY instead of depends on
gpio: lp87565: Set proper output level and direction for direction_output
MAINTAINERS: Add entry for Whiskey Cove PMIC GPIO driver
sci_clk_get() API was pretty broken and nobody noticed. There were some
CPUfreq crashes on C.H.I.P devices because we failed to propagate rates
up the clk tree. Also, the Intel Atom PMC clk driver needs to mark a clk
critical if the firmware has it enabled already so that audio doesn't get
killed on Baytrail. Gemini devices have a dead serial console because
the reset control usage in the serial driver assume one method of reset
that gemini doesn't support (this will be fixed in the next version in
the reset framework so this is the small fix for -rc series). Finally
we have two rate calculation fixes, one for Exynos and one for Meson SoCs,
that fix rate inconsistencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=/JMb
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of critical fixes for changes introduce this merge window.
- The TI sci_clk_get() API was pretty broken and nobody noticed.
- There were some CPUfreq crashes on C.H.I.P devices because we
failed to propagate rates up the clk tree.
- Also, the Intel Atom PMC clk driver needs to mark a clk critical if
the firmware has it enabled already so that audio doesn't get
killed on Baytrail.
- Gemini devices have a dead serial console because the reset control
usage in the serial driver assume one method of reset that gemini
doesn't support (this will be fixed in the next version in the
reset framework so this is the small fix for -rc series).
- Finally we have two rate calculation fixes, one for Exynos and one
for Meson SoCs, that fix rate inconsistencies"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: keystone: sci-clk: Fix sci_clk_get
clk: meson: mpll: fix mpll0 fractional part ignored
clk: samsung: exynos5420: The EPLL rate table corrections
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
clk: x86: Do not gate clocks enabled by the firmware
clk: gemini: Fix reset regression
This comes a bit later than I planned, and as a consequence is a larger
than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic Meson,
Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple randconfig
build fixes. This includes making the CONFIG_MTD_XIP option compile again,
which had been broken for many years and probably has not been missed, but
it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards
to work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a2dO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
Pull sparc fixes from David Miller:
- block interrupts properly across the entire MMU context change (both
the hw MMU context change and the TSB table change) so that we don't
get a perf event interrupt in the middle. From Rob Gardner.
- be sure to register hugepages early enough, from Nitin Gupta.
- UltraSPARC-III user copy exception handling would return garbage for
the copied length in some circumstances.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix exception handling in UltraSPARC-III memcpy.
sbus: Convert to using %pOF instead of full_name
sparc: defconfig: Cleanup from old Kconfig options
sparc64: Register hugepages during arch init
sparc64: Prevent perf from running during super critical sections
Now we hit the usual ASoC-fix-flood in the middle of release.
Most of changes are trivial and device-specific, while one significant
change is the fix for unbalanced of_graph_*() refcounts. This
involved with the change in the graph API itself that had been a bit
messy.
-----BEGIN PGP SIGNATURE-----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=k+0o
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Now we hit the usual ASoC-fix-flood in the middle of release.
Most of the changes are trivial and device-specific, while one
significant change is the fix for unbalanced of_graph_*() refcounts.
This involved a change in the graph API itself that had been a bit
messy"
* tag 'sound-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix speaker output from VAIO VPCL14M1R
device property: Fix usecount for of_graph_get_port_parent()
ASoC: rt5665: fix wrong register for bclk ratio control
ASoC: Intel: Use MCLK instead of BLCK as the sysclock for RT5514 codec on kabylake platform
ASoC: Intel: Enabling ASRC for RT5663 codec on kabylake platform
ASoC: codecs: msm8916-analog: fix DIG_CLK_CTL_RXD3_CLK_EN define
ASoC: Intel: Skylake: Fix missing sentinels in sst_acpi_mach
ASoC: sh: hac: add missing "int ret"
ASoC: samsung: odroid: Fix EPLL frequency values
ASoC: sgtl5000: Use snd_soc_kcontrol_codec()
ASoC: rt5665: fix GPIO6 pin function define
ASoC: ux500: Restore platform DAI assignments
ASoC: fix pcm-creation regression
ASoC: do not close shared backend dailink
ASoC: pxa: SND_PXA2XX_SOC should depend on HAS_DMA
ASoC: Intel: Skylake: Fix default dma_buffer_size
ASoC: rt5663: Update the HW default values based on the shipping version
ASoC: imx-ssi: add check on platform_get_irq return value
Including:
- Fix a scheduling-while-atomic bug in the AMD IOMMU driver. It
was found after the checker was enabled earlier.
- A fix for the virtual APIC code in the AMD IOMMU driver which
delivers device interrupts directly into KVM guests for
assigned devices.
- Fixes for the recently merged lock-less page-table code for
ARM. The redundant TLB syncs got reverted and locks added
again around the TLB sync code.
- Fix for error handling in arm_smmu_add_device()
- Address sanitization fix for arm io-pgtable code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Z9oV
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- fix a scheduling-while-atomic bug in the AMD IOMMU driver. It was
found after the checker was enabled earlier.
- a fix for the virtual APIC code in the AMD IOMMU driver which
delivers device interrupts directly into KVM guests for assigned
devices.
- fixes for the recently merged lock-less page-table code for ARM. The
redundant TLB syncs got reverted and locks added again around the TLB
sync code.
- fix for error handling in arm_smmu_add_device()
- address sanitization fix for arm io-pgtable code
* tag 'iommu-fixes-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix schedule-while-atomic BUG in initialization code
iommu/amd: Enable ga_log_intr when enabling guest_mode
iommu/io-pgtable: Sanitise map/unmap addresses
iommu/arm-smmu: Fix the error path in arm_smmu_add_device
Revert "iommu/io-pgtable: Avoid redundant TLB syncs"
iommu/mtk: Avoid redundant TLB syncs locally
iommu/arm-smmu: Reintroduce locking around TLB sync operations
- Fix NULL pointer dereference for block I/O during hotplug
MMC host:
- sdhci-of-at91: Fix card detect for non-removable cards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VpnQ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of mmc fixes intended for v4.13-rc4.
MMC core:
- Fix NULL pointer dereference for block I/O during hotplug
MMC host:
- sdhci-of-at91: Fix card detect for non-removable cards"
* tag 'mmc-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: bypass the queue even if usage is present for hotplug
mmc: sdhci-of-at91: force card detect value for non removable devices
-----BEGIN PGP SIGNATURE-----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=nQKg
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.13-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Either my email ate everything or everyone is on holidays, either way
all I can find is some lonely AMD fixes"
[ Europe might be on vacation, and the Pacific NW is too hot for work. ]
* tag 'drm-fixes-for-v4.13-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: Use list_del_init in amdgpu_mn_unregister
drm/amdgpu: Fix undue fallthroughs in golden registers initialization
drm/amdgpu: fix header on gfx9 clear state
When resuming, set up registers that have been lost in the sleep state.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Just a few small fixes for 4.13.
* 'drm-fixes-4.13' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Use list_del_init in amdgpu_mn_unregister
drm/amdgpu: Fix undue fallthroughs in golden registers initialization
drm/amdgpu: fix header on gfx9 clear state
- Fix a device ID of Hisilicon Hip07/08 in the ACPI APD (AMD SoC)
driver (Hanjun Guo).
- Fix list corruption (introduced during the 4.11 cycle) in the ACPI
LPSS (Intel SoC) driver (Hans de Goede).
- Fix PCC mailbox handling code crash during initialization when
PCCT is not present and PCC channel 0 is requested (Hoan Tran).
- Fix a WDAT watchdog initialization issue causing platform device
creation to fail due to partially overlapping address ranges in
resources (Ryan Kennedy).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ZD/q
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two issues in the ACPI SoC drivers (Intel LPSS and AMD APD),
a crash in the PCC mailbox initialization code and a WDAT watchdog
initialization failure.
Specifics:
- Fix a device ID of Hisilicon Hip07/08 in the ACPI APD (AMD SoC)
driver (Hanjun Guo).
- Fix list corruption (introduced during the 4.11 cycle) in the ACPI
LPSS (Intel SoC) driver (Hans de Goede).
- Fix PCC mailbox handling code crash during initialization when PCCT
is not present and PCC channel 0 is requested (Hoan Tran).
- Fix a WDAT watchdog initialization issue causing platform device
creation to fail due to partially overlapping address ranges in
resources (Ryan Kennedy)"
* tag 'acpi-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: APD: Fix HID for Hisilicon Hip07/08
mailbox: pcc: Fix crash when request PCC channel 0
ACPI / watchdog: Fix init failure with overlapping register regions
ACPI / LPSS: Only call pwm_add_table() for the first PWM controller
- Fix the handling of the scaling_cur_freq cpufreq policy attribute
on x86 systems with the MPERF/APERF registers present to make it
behave more as expected after recent changes (Rafael Wysocki).
- Drop a leftover callback from the intel_pstate driver which also
prevents the cpuinfo_cur_freq cpufreq policy attribute from being
incorrectly exposed when intel_pstate works in the active mode
(Rafael Wysocki).
- Add a missing piece describing the cpuinfo_cur_freq policy
attribute to cpufreq documentation (Rafael Wysocki).
- Fix up a recently added part of the Thunderbolt driver to avoid
aborting system suspends if its mailbox commands time out (Rafael
Wysocki).
- Update device runtime PM framework documentation to reflect the
current behavior of the code (Johan Hovold).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=j2UJ
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq issues, one introduced recently and one related
to recent changes, fix cpufreq documentation, fix up recently added
code in the Thunderbolt driver and update runtime PM framework
documentation.
Specifics:
- Fix the handling of the scaling_cur_freq cpufreq policy attribute
on x86 systems with the MPERF/APERF registers present to make it
behave more as expected after recent changes (Rafael Wysocki).
- Drop a leftover callback from the intel_pstate driver which also
prevents the cpuinfo_cur_freq cpufreq policy attribute from being
incorrectly exposed when intel_pstate works in the active mode
(Rafael Wysocki).
- Add a missing piece describing the cpuinfo_cur_freq policy
attribute to cpufreq documentation (Rafael Wysocki).
- Fix up a recently added part of the Thunderbolt driver to avoid
aborting system suspends if its mailbox commands time out (Rafael
Wysocki).
- Update device runtime PM framework documentation to reflect the
current behavior of the code (Johan Hovold)"
* tag 'pm-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thunderbolt: icm: Ignore mailbox errors in icm_suspend()
cpufreq: x86: Make scaling_cur_freq behave more as expected
PM / runtime: Document new pm_runtime_set_suspended() constraint
cpufreq: docs: Add missing cpuinfo_cur_freq description
cpufreq: intel_pstate: Drop ->get from intel_pstate structure
The commit 304419d8a7 ("mmc: core: Allocate per-request data using the
block layer core") refactored mechanism of queue handling caused
mmc_init_request() can be called just after mmc_cleanup_queue() caused null
pointer dereference.
Another commit bbdc74dc19 ("mmc: block: Prevent new req entering queue
after its cleanup") tried to fix the problem. However it actually miss one
corner case.
We could still reproduce the issue mentioned with these steps:
(1) insert a SD card and mount it
(2) hotplug it, so it will leave md->usage still be counted
(3) reboot the system which will sync data and umount the card
[Unable to handle kernel NULL pointer dereference at virtual address
00000000
[user pgtable: 4k pages, 48-bit VAs, pgd = ffff80007bab3000
[[0000000000000000] *pgd=000000007a828003, *pud=0000000078dce003,
*pmd=000000007aab6003, *pte=0000000000000000
[Internal error: Oops: 96000007 [#1] PREEMPT SMP
[Modules linked in:
[CPU: 3 PID: 3507 Comm: umount Tainted: G W
4.13.0-rc1-next-20170720-00012-g9d9bf45 #33
[Hardware name: Firefly-RK3399 Board (DT)
[task: ffff80007a1de200 task.stack: ffff80007a01c000
[PC is at mmc_init_request+0x14/0xc4
[LR is at alloc_request_size+0x4c/0x74
[pc : [<ffff0000087d7150>] lr : [<ffff000008378fe0>] pstate: 600001c5
[sp : ffff80007a01f8f0
....
[[<ffff0000087d7150>] mmc_init_request+0x14/0xc4
[[<ffff000008378fe0>] alloc_request_size+0x4c/0x74
[[<ffff00000817ac28>] mempool_create_node+0xb8/0x17c
[[<ffff00000837aadc>] blk_init_rl+0x9c/0x120
[[<ffff000008396580>] blkg_alloc+0x110/0x234
[[<ffff000008396ac8>] blkg_create+0x424/0x468
[[<ffff00000839877c>] blkg_lookup_create+0xd8/0x14c
[[<ffff0000083796bc>] generic_make_request_checks+0x368/0x3b0
[[<ffff00000837b050>] generic_make_request+0x1c/0x240
So mmc_blk_put wouldn't calling blk_cleanup_queue which actually the
QUEUE_FLAG_DYING and QUEUE_FLAG_BYPASS should stay. Block core expect
blk_queue_bypass_{start, end} internally to bypass/drain the queue before
actually dying the queue, so it didn't expose API to set the queue bypass.
I think we should set QUEUE_FLAG_BYPASS whenever queue is removed, although
the md->usage is still counted, as no dispatch queue could be found then.
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the block layer core")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the device is non removable, the card detect signal is often used
for another purpose i.e. muxed to another SoC peripheral or used as a
GPIO. It could lead to wrong behaviors depending the default value of
this signal if not muxed to the SDHCI controller.
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>