Info about new measurements are cached in the iint for performance. When
the inode is flushed from cache, the associated iint is flushed as well.
Subsequent access to the inode will cause the inode to be re-measured and
will attempt to add a duplicate entry to the measurement list.
This patch frees the duplicate measurement memory, fixing a memory leak.
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Cc: stable@vger.kernel.org
This fixes a build break attempting to build a Tegra20-only kernel
without device tree enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that Tegra20 and Tegra30 device tree board files are separate,
MACH_TEGRA_DT (which enables the Tegra20 device tree board file) should
depend on Tegra20 support being enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
tegra_init_clock() is written to call tegra2_init_clocks(), which only
exists if Tegra20 support is enabled. This breaks the build of a
Tegra30-only kernel.
tegra_init_clock() isn't actually used any more; tegra20_init_early()
calls tegra2_init_clocks() directly. So, just delete this function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
tegra30_pinmux_init() is called from the pinmux's probe() function, and
hence should be __devinit not __init.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
tegra20_pinmux_init() is called from the pinmux's probe() function, and
hence should be __devinit not __init.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently, the Tegra pinmux is initialized at different times when booting
with and without device tree:
Without device tree:
1) Pinmux and GPIO drivers are registered.
2) Pinmux is configured.
3) All other drivers are registered.
With device tree:
1) All drivers are registered and probed, including pinmux and GPIO.
2) Pinmux is configured.
This change modifies board-pinmux.c to detect pinmux and GPIO driver
registration using bus notifiers. This allows pinmux configuration to
happen immediately after the pinmux driver is probed, irrespective of
whether the pinmux driver is manually registered by board-pinmux.c, or
if it's instantiated during device tree parsing.
To support this with device tree, the pinmux init functions must be
called prior to instantiating devices from device tree, so that the
notifiers are set up before-hand.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This moves the implementation of *_pinmux_init() into a single location.
The board-specific pinmux data is left in each board's own file. This
will allow future changes that set up the pinmux in a more complex
fashion to do so without duplicating that code in each board's pinmux
file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pin group PTA does not support function RSVD3. However, the current
pinmux driver doesn't check this when setting RSVD functions, and ends
up writing 3 to the HW register. 3 is actually represented by function
GMI, so update the pinmux table to request that instead in order to
obtain the same register programming without requesting invalid
configurations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rather than modifying seaboard_pinmux[] using ventana_pinmux[], split
seaboard_pinmux[] into common_pinmux[] and seaboard_pinmux[], and then
actually apply common_pinmux[] always, followed by the appopriate one
of seaboard_pinmux[] or ventana_pinmux[].
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Some of the entries in ventana_pinmux[] are identical to what's already in
seaboard_pinmux[]. Remove the overrides from the Ventana table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Harmony pinmux table is already set up to mux the PCIe signals onto
the appropriate pin groups. Don't manually fiddle with the pinmux in the
Harmony PCIe setup code.
Merge note: This will have a merge conflict with Peter De Schrijver's
"arm/tegra: prepare pinmux code for multiple tegra variants" due to
context. When merging the two, make sure to also remove the include
of <mach/pinmux-tegra20.h> that his patch added, since it's no longer
needed after this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The pinctrl device name is included in the pinctrl map table, and used
as a parameter to pin_config_*() functions. Hence, it must be the same
for non-DT and DT kernels. Add AUXDATA to cause this.
The GPIO device name will be used by the pinmux/GPIO initialization code
in a later patch, and needs to stay constant.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Seaboard and Ventana share some GPIOs, but others are different. Split the
GPIO table into common, seaboard-specific, and ventana-specific tables, so
that only the correct ones are enabled for each board. Add a few missing
audio-related GPIOs for Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update the defconfig for tegra due to the addition of tegra30 and rename
of t20/t30 options.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This brings all the GPIO key definitions from board-seaboard.c into
tegra-seaboard.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ADT7461 is a temperature monitoring IC. One is present on the DVC
I2C bus on Seaboard.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update the device tree to indicate which I2C controller is the DVC
controller. AUXDATA needs to be updated too, since the compatible
value changed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
One of the Tegra I2C blocks is inside the DVC (Digital Voltage Controller)
block. This block is identical to the rest of the I2C blocks, except that
it only supports master mode, it has registers moved around, and it needs
some extra init to get it into I2C mode. The register moves are handled
by i2c_readl and i2c_writel
This patch adds a new compatible value for controllers of this "DVC"
type; I figured that this approach was reasonable, as opposed to adding
an is-dvc property under the existing compatible value, since the HW
truly is different.
v2: Call of_device_is_compatible() to determine is_dvc, instead of storing
the flag in tegra_i2c_of_match[]'s .data field.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver is parameterized in two ways:
a) Platform data, which supplies the set of GPIOs used by the driver.
These GPIOs can now be parsed out of device tree.
b) Machine-specific DAPM route arrays embedded into the ASoC machine
driver itself. Historically, the driver picks the appropriate array
to use using machine_is_*(). The driver now requires this array to
be parsed from device tree when instantiated through device tree,
using the core ASoC support for this parsing.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_audio_routing(), a utility function that can
parses a simple DAPM route table from device tree.The machine driver
specifies the DT property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_card_name(), a utility function that sets a
card's name from device tree. The machine driver specifies the DT
property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The module desciption says this is ASoC alc5621/2/3 driver.
Make the naming consistent with the reset of the code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 49920bc (dmaengine: add new enum dma_transfer_direction)
changes the type of parameter 'direction' of device_prep_dma_cyclic
from dma_data_direction to dma_transfer_direction.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to export s3c_pcm_dai after multi-component patch.
Thus remove export of s3c_pcm_dai and make it static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At this stage only Toshiba AC100/Dynabook supported.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
You didn't mean this to be a bool.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When SDIO runtime PM was originally introduced, we immediately faced
two regressions with two different chipsets, and in response decided
not to enable it by default.
With the recent work on the 8686 we hoped we found all the gotchas,
so 08da834 did make sense (at least experimentally).
Unfortunately we now see that some setups out there still refuse to
work when SDIO runtime PM is enabled by default (see
http://www.spinics.net/lists/linux-mmc/msg11161.html), and obviously
we can't live with these kind of regressions.
This reverts commit 08da834a24.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Drop the "state" argument from sdhci_suspend_host. Its only user is the
PCI glue; this allows to move all SDHCI glues to use dev_pm_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Correct sense on freectxts increment and decrement
RDMA/cma: Verify private data length
IB/mlx4: Fix shutdown crash accessing a non-existent bitmap
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - fix touchpad not working after S2R on Vostro V13
Input: cma3000_d0x - fix signedness bug in cma3000_thread_irq()
Input: wacom - add product id used by Samsung Slate 7
This documents the fields added to security_file_mmap() that were
introduced in ed03218951.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <jmorris@namei.org>
The current implementation just ignore any NULL string inserted in a
multiple strings property.
In some cases we can have a property with a fix number of strings but
not necessarily used, like for example in a list of valid pinmux modes.
prop = "uart_rx", "uart_tx", "", "", "safe_mode";
Do no skip NULL string and take them into account in
of_property_read_string_index and of_property_count_strings.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
We are currently using 'cavium', 'cortina' and 'st', add them to the
list of known prefixes.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Adds the device id needed for the USB Ethernet Adapter delivered by
ASUS with their Zenbook.
Signed-off-by: Aurelien Jacobs <aurel@gnuage.org>
Acked-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Runtime DC calibration was previously conditional. Remove this
behaviour, as new devices support runtime DC calibration,
while older devices ignore the runtime DC calibration request.
This patch addresses low TX throughput issues seen with the 6205.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
instead of doing all the work in IWL_TM_CMD_APP2DEV_GET_DEVICE_ID, just use
the information from bus_get_hw_id()
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
