On OMAP4 SOC, intecronnects has many write buffers in the async bridges
and they need to be drained before CPU enters into standby state.
Patch 'OMAP4: PM: Add CPUX OFF mode support' added CPU PM support
but OMAP errata i688 (Async Bridge Corruption) needs to be taken
care to avoid issues like system freeze, CPU deadlocks, random
crashes with register accesses, synchronisation loss on initiators
operating on both interconnect port simultaneously.
As per the errata, if a data is stalled inside asynchronous bridge
because of back pressure, it may be accepted multiple times, creating
pointer misalignment that will corrupt next transfers on that data
path until next reset of the system (No recovery procedure once
the issue is hit, the path remains consistently broken).
Async bridge can be found on path between MPU to EMIF and
MPU to L3 interconnect. This situation can happen only when the
idle is initiated by a Master Request Disconnection (which is
trigged by software when executing WFI on CPU).
The work-around for this errata needs all the initiators
connected through async bridge must ensure that data path
is properly drained before issuing WFI. This condition will be
met if one Strongly ordered access is performed to the
target right before executing the WFI. In MPU case, L3 T2ASYNC
FIFO and DDR T2ASYNC FIFO needs to be drained. IO barrier ensure
that there is no synchronisation loss on initiators operating
on both interconnect port simultaneously.
Thanks to Russell for a tip to conver assembly function to
C fuction there by reducing 40 odd lines of code from the patch.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the MPUSS OSWR (Open Switch Retention) support. The MPUSS
OSWR configuration is as below.
- CPUx L1 and logic lost, MPUSS logic lost, L2 memory is retained
OMAP4460 onwards, MPUSS power domain doesn't support OFF state any more
anymore just like CORE power domain. The deepest state supported is OSWR.
On OMAP4430 secure devices too, MPUSS off mode can't be used because of
a bug which alters Ducati and Tesla states. Hence MPUSS off mode as an
independent state isn't supported on OMAP44XX devices.
Ofcourse when MPUSS power domain transitions to OSWR along
with device off mode, it eventually hits off state since memory
contents are lost.
Hence the MPUSS off mode independent state is not attempted without
device off mode. All the necessary infrastructure code for MPUSS
off mode is in place as part of this series.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
When MPUSS hits off-mode, L2 cache is lost. This patch adds L2X0
necessary maintenance operations and context restoration in the
low power code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add WakeupGen and secure GIC low power support to save and restore
it's registers. WakeupGen Registers are saved to pre-defined SAR RAM layout
and the restore is automatically done by hardware(ROM code) while coming
out of MPUSS OSWR or Device off state. Secure GIC is saved using secure
API and restored by hardware like WakeupGen.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With OMAP4 suspend, idle and hotplug series, we no longer need
do_wfi() macro.
Remove the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds MPUSS(MPU Sub System) power domain
CSWR(Close Switch Retention) support to system wide suspend.
For MPUSS power domain to hit retention(CSWR or OSWR), both
CPU0 and CPU1 power domains need to be in OFF or DORMANT state,
since CPU power domain CSWR is not supported by hardware
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Default arch_idle() isn't good enough for OMAP4 because of aync bridge errata
and necessity of NOPs post WFI to avoid speculative prefetch aborts.
Hence Use OMAP4 custom omap_do_wfi() hook for default idle.
Later in the series, async bridge errata work-around patch updates the
omap_do_wfi() with necessary interconnects barriers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The SGI(Software Generated Interrupts) are not wakeup capable from
low power states. This is known limitation on OMAP4 and needs to be
worked around by using software forced clockdomain wake-up. CPU0 forces
the CPU1 clockdomain to software force wakeup.
More details can be found in OMAP4430 TRM - Version J
Section :
4.3.4.2 Power States of CPU0 and CPU1
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Program non-boot CPUs to hit lowest supported power state
when it is off-lined using cpu hotplug framework.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the __INIT from omap_secondary_startup() so that it can
be re-used for CPU hotplug.
While at this, remove the un-used AUXBOOT register reference.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds the CPU0 and CPU1 off mode support. CPUX close switch
retention (CSWR) is not supported by hardware design.
The CPUx OFF mode isn't supported on OMAP4430 ES1.0
CPUx sleep code is common for hotplug, suspend and CPUilde.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP WakeupGen is the interrupt controller extension used along
with ARM GIC to wake the CPU out from low power states on
external interrupts.
The WakeupGen unit is responsible for generating the wakeup event
from the incoming interrupts and enable bits. It is implemented
in the MPU always ON power domain. During normal operation,
WakeupGen delivers the external interrupts directly to the GIC.
WakeupGen specification has one restriction as per Veyron version 1.6.
It is SW responsibility to program interrupt enabling/disabling
coherently in the GIC and in the WakeupGen enable registers. That is, a
given interrupt for a given CPU is either enable at both GIC and WakeupGen,
or disable at both, but no mix. That's the reason the WakeupGen is
implemented as an extension of GIC.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Allocate the memory to save secure ram context which needs
to be done when MPU is hitting OFF mode.
The ROM code expects a physical address to this memory
and hence use memblock APIs to reserve this memory as part
of .reserve() callback. Maximum size as per secure RAM requirements
is allocated.
To keep omap1 build working, omap-secure.h file is created
under plat-omap directory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP secure/emulation devices, certain APIs are exported by secure
code. Add an infrastructure so that relevant operations on secure
devices can be implemented using it.
While at this, rename omap44xx-smc.S to omap-smc.S since the common APIs
can be used on other OMAP's too.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Initialise hardware supervised mode for all clockdomains if it's
supported. Initiate sleep transition for other clockdomains,
if they are not being used.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4430 ES1.0, Power Management features are not supported.
Avoid omap4_pm_init() on ES1.0 silicon so that we can continue
to use same kernel binary to boot on all OMAP4 silicons.
The ES1.0 boot failure with OMAP4 PM series was because of
the clockdomain initialisation code. Hardware supervised
clockdomain mode isn't functional for all clockdomains
on OMAP4430 ES1.0 silicon so avoid the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As per OMAP4430 TRM, the dynamic dependency between MPUSS -> EMIF
and MPUSS -> L4PER/L3_* and DUCATI -> L3_* clockdomains is enable
by default. Refer register CM_MPU_DYNAMICDEP description for details.
But these dynamic dependencies doesn't work as expected. The hardware
recommendation is to enable static dependencies for above clockdomains.
Without this, system locks up or randomly crashes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SAR RAM support on OMAP4430. SAR RAM used to save
and restore the HW context in low power modes.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch exports APIs to get base address for GIC
distributor, CPU interface, SCU and PL310 L2 Cache which
are used in OMAP4 PM code.
This was suggested by Kevin Hilman <khilman@ti.com> during
OMAP4 PM code review.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 L2X0 initialisation code uses BUG_ON() for the ioremap()
failure scenarios.
Use WARN_ON() instead and allow graceful function exits.
This was suggsted by Kevin Hilman <khilman@ti.com> during
OMAP4 PM code review.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The delaylog mode has been the default for a long time, and the nodelaylog
option has been scheduled for removal in Linux 3.3. Remove it and code
only used by it now that we have opened the 3.3 window.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Now that all early memory information is in memblock when enabled, we
can implement reverse free area iterator and use it to implement NUMA
aware allocator which is then wrapped for simpler variants instead of
the confusing and inefficient mending of information in separate NUMA
aware allocator.
Implement for_each_free_mem_range_reverse(), use it to reimplement
memblock_find_in_range_node() which in turn is used by all allocators.
The visible allocator interface is inconsistent and can probably use
some cleanup too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Now all ARCH_POPULATES_NODE_MAP archs select HAVE_MEBLOCK_NODE_MAP -
there's no user of early_node_map[] left. Kill early_node_map[] and
replace ARCH_POPULATES_NODE_MAP with HAVE_MEMBLOCK_NODE_MAP. Also,
relocate for_each_mem_pfn_range() and helper from mm.h to memblock.h
as page_alloc.c would no longer host an alternative implementation.
This change is ultimately one to one mapping and shouldn't cause any
observable difference; however, after the recent changes, there are
some functions which now would fit memblock.c better than page_alloc.c
and dependency on HAVE_MEMBLOCK_NODE_MAP instead of HAVE_MEMBLOCK
doesn't make much sense on some of them. Further cleanups for
functions inside HAVE_MEMBLOCK_NODE_MAP in mm.h would be nice.
-v2: Fix compile bug introduced by mis-spelling
CONFIG_HAVE_MEMBLOCK_NODE_MAP to CONFIG_MEMBLOCK_HAVE_NODE_MAP in
mmzone.h. Reported by Stephen Rothwell.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
score used early_node_map[] just to prime free_area_init_nodes(). Now
memblock can be used for the same purpose and early_node_map[] is
scheduled to be dropped. Use memblock instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
s390 used early_node_map[] just to prime free_area_init_nodes(). Now
memblock can be used for the same purpose and early_node_map[] is
scheduled to be dropped. Use memblock instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
mips used early_node_map[] just to prime free_area_init_nodes(). Now
memblock can be used for the same purpose and early_node_map[] is
scheduled to be dropped. Use memblock instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: linux-mips@linux-mips.org
ia64 used early_node_map[] just to prime free_area_init_nodes(). Now
memblock can be used for the same purpose and early_node_map[] is
scheduled to be dropped. Use memblock instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
sh doesn't access early_node_map[] directly and enabling
HAVE_MEMBLOCK_NODE_MAP is trivial - replacing add_active_range() calls
with memblock_set_node() and selecting HAVE_MEMBLOCK_NODE_MAP is
enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
sparc doesn't access early_node_map[] directly and enabling
HAVE_MEMBLOCK_NODE_MAP is trivial - replacing add_active_range() calls
with memblock_set_node() and selecting HAVE_MEMBLOCK_NODE_MAP is
enough.
-v2: Use select in Kconfig instead as suggested by Sam Ravnborg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: sparclinux@vger.kernel.org
powerpc doesn't access early_node_map[] directly and enabling
HAVE_MEMBLOCK_NODE_MAP is trivial - replacing add_active_range() calls
with memblock_set_node() and selecting HAVE_MEMBLOCK_NODE_MAP is
enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Implement memblock_add_node() which can add a new memblock memory
region with specific node ID.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
The only function of memblock_analyze() is now allowing resize of
memblock region arrays. Rename it to memblock_allow_resize() and
update its users.
* The following users remain the same other than renaming.
arm/mm/init.c::arm_memblock_init()
microblaze/kernel/prom.c::early_init_devtree()
powerpc/kernel/prom.c::early_init_devtree()
openrisc/kernel/prom.c::early_init_devtree()
sh/mm/init.c::paging_init()
sparc/mm/init_64.c::paging_init()
unicore32/mm/init.c::uc32_memblock_init()
* In the following users, analyze was used to update total size which
is no longer necessary.
powerpc/kernel/machine_kexec.c::reserve_crashkernel()
powerpc/kernel/prom.c::early_init_devtree()
powerpc/mm/init_32.c::MMU_init()
powerpc/mm/tlb_nohash.c::__early_init_mmu()
powerpc/platforms/ps3/mm.c::ps3_mm_add_memory()
powerpc/platforms/embedded6xx/wii.c::wii_memory_fixups()
sh/kernel/machine_kexec.c::reserve_crashkernel()
* x86/kernel/e820.c::memblock_x86_fill() was directly setting
memblock_can_resize before populating memblock and calling analyze
afterwards. Call memblock_allow_resize() before start populating.
memblock_can_resize is now static inside memblock.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Total size of memory regions was calculated by memblock_analyze()
requiring explicitly calling the function between operations which can
change memory regions and possible users of total size, which is
cumbersome and fragile.
This patch makes each memblock_type track total size automatically
with minor modifications to memblock manipulation functions and remove
requirements on calling memblock_analyze(). [__]memblock_dump_all()
now also dumps the total size of reserved regions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
* early_init_devtree(): Total memory size is aligned to PAGE_SIZE;
however, alignment isn't enforced if memory_limit is explicitly
specified. Simplify the logic and always apply PAGE_SIZE alignment.
* MMU_init(): memblock regions is truncated by directly modifying
memblock.memory.cnt. This is incomplete (reserved array is not
truncated) and unnecessarily low level hindering further memblock
improvments. Use memblock_enforce_memory_limit() instead.
* wii_memory_fixups(): Unnecessarily low level direct manipulation of
memblock regions. The same result can be achieved using properly
abstracted operations. Reimplement using memblock API.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
With recent updates, the basic memblock operations are robust enough
that there's no reason for memblock_enfore_memory_limit() to directly
manipulate memblock region arrays. Reimplement it using
__memblock_remove().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Allow memblock users to specify range where @base + @size overflows
and automatically cap it at maximum. This makes the interface more
robust and specifying till-the-end-of-memory easier.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
__memblock_remove()'s open coded region manipulation can be trivially
replaced with memblock_islate_range(). This increases code sharing
and eases improving region tracking.
This pulls memblock_isolate_range() out of HAVE_MEMBLOCK_NODE_MAP.
Make it use memblock_get_region_node() instead of assuming rgn->nid is
available.
-v2: Fixed build failure on !HAVE_MEMBLOCK_NODE_MAP caused by direct
rgn->nid access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
memblock_set_node() operates in three steps - break regions crossing
boundaries, set nid and merge back regions. This patch separates the
first part into a separate function - memblock_isolate_range(), which
breaks regions crossing range boundaries and returns range index range
for regions properly contained in the specified memory range.
This doesn't introduce any behavior change and will be used to further
unify region handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
memblock_init() initializes arrays for regions and memblock itself;
however, all these can be done with struct initializers and
memblock_init() can be removed. This patch kills memblock_init() and
initializes memblock with struct initializer.
The only difference is that the first dummy entries don't have .nid
set to MAX_NUMNODES initially. This doesn't cause any behavior
difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
memblock no longer depends on having one more entry at the end during
addition making the sentinel entries at the end of region arrays not
too useful. Remove the sentinels. This eases further updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Add __memblock_dump_all() which dumps memblock configuration whether
memblock_debug is enabled or not.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Make memblock_double_array(), __memblock_alloc_base() and
memblock_alloc_nid() use memblock_reserve() instead of calling
memblock_add_region() with reserved array directly. This eases
debugging and updates to memblock_add_region().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
memblock_{add|remove|free|reserve}() return either 0 or -errno but had
long as return type. Chage it to int. Also, drop 'extern' from all
prototypes in memblock.h - they are unnecessary and used
inconsistently (especially if mm.h is included in the picture).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
24aa07882b (memblock, x86: Replace memblock_x86_reserve/free_range()
with generic ones) removed arch/x86/include/asm/memblock.h and dropped
its inclusion from include/linux/memblock.h which breaks other
architectures which depended on the generic memblock.h pulling in the
arch specific one.
However, the proper fix isn't adding back the asm inclusion. memblock
doesn't have any arch dependent part and doesn't need arch specific
header file and asm/memblock.h files are either practically empty or
contain mostly unrelated arch specific stuff.
* In microblaze, sh, powerpc, sparc and openrisc, asm/memblock.h is
either empty or just contains unused MEMBLOCK_DBG() macro. Remove
them.
* In arm and unicore32, asm/memblock.h contains arch specific stuff.
Include it directly from its users. It might be a good idea to
rename the header file to avoid confusion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
The EHCI USB controller of the Cell Super Companion Chip used in the PS3
will stop the root hub after all root hub ports are suspended. When in
this condition the ehci-hcd handshake routine will return -ETIMEDOUT and
the USB runtime suspend sequence will fail. The STS_HLT bit will not be
set, so inspection of the frame index is used to test for the condition.
Add a new routine handshake_for_broken_root_hub() that is called after
an unsuccessful -ETIMEDOUT handshake. On PS3 handshake_for_broken_root_hub()
will test for the condition, and if found will return success to allow the
USB suspend to complete. For all other platforms
handshake_for_broken_root_hub() will return -ETIMEDOUT
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
PS3 EHCI HC errata fix 316 - The PS3 EHCI HC will reset its
internal INSNREGXX setup regs back to the chip default values
on Host Controller Reset (CMD_RESET) or Light Host Controller
Reset (CMD_LRESET). The work-around for this is for the HC
driver to re-initialise these regs when ever the HC is reset.
Adds a new helper routine ps3_ehci_setup_insnreg() which is
called from ps3_ehci_hc_reset().
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Remove the ehci_reset() call done in the ehci_run() routine of the
USB EHCI host controller driver and add an ehci_reset() call to the
probe processing of all EHCI platform drivers that do not already call
ehci_reset().
The call to ehci_reset() from ehci_run() was problematic for several
platform drivers, and unnecessary for others. This change moves the
decision to call ehci_reset() at driver startup to the platform
driver code.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
