netdev_queue_release() should be called even if CONFIG_XPS=n
to properly release device reference.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f07d960df3 (tcp: avoid frag allocation for small frames)
breaked assumption in tcp stack that skb is either linear (skb->data_len
== 0), or fully fragged (skb->data_len == skb->len)
tcp_trim_head() made this assumption, we must fix it.
Thanks to Vijay for providing a very detailed explanation.
Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality for avoiding orphaning SKB too early.
The original skb is stashed away and the original destructor is called
from the hi-jacked flow-on callback. If CAIF interface goes down and a
hi-jacked SKB exists, the original skb->destructor is restored.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control is implemented by inspecting the qdisc queue length
in order to detect potential overflow on the TX queue. When a threshold
is reached flow-off is sent upwards in the CAIF stack. At the same time
the skb->destructor is hi-jacked by orphaning the SKB and the original
destructor is replaced with a "flow-on" callback. When the "hi-jacked"
SKB is consumed the queue should be empty, and the "flow-on" callback
is called and xon is sent upwards in the CAIF stack.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCM 1.0 does not support anything but Ethernet framing, hence
CAIF payload will be put into Ethernet frames.
Discovery is based on fixed USB vendor 0x04cc (ST-Ericsson),
product-id 0x230f (NCM). In this variant only CAIF payload is sent over
the NCM interface.
The CAIF stack (cfusbl.c) will when USB interface register first check if
we got a CDC NCM USB interface with the right VID, PID.
It will then read the device's Ethernet address and create a 'template'
Ethernet TX header, using a broadcast address as the destination address,
and EthType 0x88b5 (802.1 Local Experimental - vendor specific).
A protocol handler for 0x88b5 is setup for reception of CAIF frames from
the CDC NCM USB interface.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EthType 0x88b5.
This Ethertype value is available for public use for prototype and
vendor-specific protocol development,as defined in Amendment 802a
to IEEE Std 802.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the below build break by including common.h
arch/arm/mach-omap2/cpuidle34xx.c: In function 'omap3_enter_idle':
arch/arm/mach-omap2/cpuidle34xx.c:117: error: implicit declaration of function 'omap_irq_pending'
make[1]: *** [arch/arm/mach-omap2/cpuidle34xx.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the build break by adding the necessary irq functions to
common header.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reduce the number of dst_get_neighbour_noref() calls within a single
call chain. Primarily by passing the neighbour pointer down to the
helper functions.
Handle dst_get_neighbour_noref() returning NULL in ipoib_start_xmit()
by incrementing the dropped counter and freeing the packet. We don't
want it to fall through into the ARP/RARP/multicast handling, since
that should only happen when skb_dst() is NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
Three pieces of code do the same thing, create a l2t entry and then
import this information into the c4iw_ep object.
Create a helper function and call it from these 3 locations instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
This way we consolidate the RCU locking down into the place where it
actually matters, and also we can make the code handle
dst_get_neighbour_noref() returning NULL properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPV4 should do exactly what the IPV6 code does here, which is
use the neighbour obtained via the dst entry.
And now that the two code paths do the same thing, use a common
helper function to perform the operation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Roland Dreier <roland@purestorage.com>
To reflect the fact that a refrence is not obtained to the
resulting neighbour entry.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Roland Dreier <roland@purestorage.com>
It's not always true that the device_node of regulator can be found
at dev->of_node at the time when of_get_regulator_init_data() is being
called, because in some cases the regulator nodes in device tree do
not have 'struct device' behind them until regulator_dev gets created
for it by core function regulator_register().
The patch adds device_node as a new parameter to
of_get_regulator_init_data(), so that caller can pass in the node of
regulator directly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise there is no way in the bindings to configure a fixed voltage
via software. It seems reasonable to assume that if the binding explicitly
specifies a voltage we want to actually use that voltage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I get this compile failure on parisc:
drivers/pci/ats.c: In function 'ats_alloc_one':
drivers/pci/ats.c:29: error: implicit declaration of function 'kzalloc'
drivers/pci/ats.c:29: warning: assignment makes pointer from integer without a cast
drivers/pci/ats.c: In function 'ats_free_one':
drivers/pci/ats.c:45: error: implicit declaration of function 'kfree'
Because ats.c is missing linux/slab.h as an include. This patch fixes it
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All the PCI BARs of a device are enabled when the device is enabled
using pci_enable_device(). This unnecessarily enables SRIOV BARs of the
device.
On some platforms, which do not support SRIOV as yet, the
pci_enable_device() fails to enable the device if its SRIOV BARs are not
allocated resources correctly.
The following patch fixes the above problem. The SRIOV BARs are now
enabled when IOV capability of the device is enabled in sriov_enable().
NOTE: Note, there is subtle change in the pci_enable_device() API. Any
driver that depends on SRIOV BARS to be enabled in pci_enable_device()
can fail.
The patch has been touch tested on power and x86 platform.
Tested-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the set_ftrace_filter is cleared by writing just whitespace to
it, then the filter hash refcounts will be decremented but not
updated. This causes two bugs:
1) No functions will be enabled for tracing when they all should be
2) If the users clears the set_ftrace_filter twice, it will crash ftrace:
------------[ cut here ]------------
WARNING: at /home/rostedt/work/git/linux-trace.git/kernel/trace/ftrace.c:1384 __ftrace_hash_rec_update.part.27+0x157/0x1a7()
Modules linked in:
Pid: 2330, comm: bash Not tainted 3.1.0-test+ #32
Call Trace:
[<ffffffff81051828>] warn_slowpath_common+0x83/0x9b
[<ffffffff8105185a>] warn_slowpath_null+0x1a/0x1c
[<ffffffff810ba362>] __ftrace_hash_rec_update.part.27+0x157/0x1a7
[<ffffffff810ba6e8>] ? ftrace_regex_release+0xa7/0x10f
[<ffffffff8111bdfe>] ? kfree+0xe5/0x115
[<ffffffff810ba51e>] ftrace_hash_move+0x2e/0x151
[<ffffffff810ba6fb>] ftrace_regex_release+0xba/0x10f
[<ffffffff8112e49a>] fput+0xfd/0x1c2
[<ffffffff8112b54c>] filp_close+0x6d/0x78
[<ffffffff8113a92d>] sys_dup3+0x197/0x1c1
[<ffffffff8113a9a6>] sys_dup2+0x4f/0x54
[<ffffffff8150cac2>] system_call_fastpath+0x16/0x1b
---[ end trace 77a3a7ee73794a02 ]---
Link: http://lkml.kernel.org/r/20111101141420.GA4918@debian
Reported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
A update is made to the sched:sched_switch event that adds some
logic to the first parameter of the __print_flags() that shows the
state of tasks. This change cause perf to fail parsing the flags.
A simple fix is needed to have the parser be able to process ops
within the argument.
Cc: stable@vger.kernel.org
Reported-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If cpu A calls jump_label_inc() just after atomic_add_return() is
called by cpu B, atomic_inc_not_zero() will return value greater then
zero and jump_label_inc() will return to a caller before jump_label_update()
finishes its job on cpu B.
Link: http://lkml.kernel.org/r/20111018175551.GH17571@redhat.com
Cc: stable@vger.kernel.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
A forced undef of a config value was used for testing and was
accidently left in during the final commit. This causes x86 to
run slower than needed while running function tracing as well
as causes the function graph selftest to fail when DYNMAIC_FTRACE
is not set. This is because the code in MCOUNT expects the ftrace
code to be processed with the config value set that happened to
be forced not set.
The forced config option was left in by:
commit 6331c28c96
ftrace: Fix dynamic selftest failure on some archs
Link: http://lkml.kernel.org/r/20111102150255.GA6973@debian
Cc: stable@vger.kernel.org
Reported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Though not all events have field 'prev_pid', it was allowed to do this:
# echo 'prev_pid == 100' > events/sched/filter
but commit 75b8e98263 (tracing/filter: Swap
entire filter of events) broke it without any reason.
Link: http://lkml.kernel.org/r/4EAF46CF.8040408@cn.fujitsu.com
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Fix a bug introduced by e9dbfae5, which prevents event_subsystem from
ever being released.
Ref_count was added to keep track of subsystem users, not for counting
events. Subsystem is created with ref_count = 1, so there is no need to
increment it for every event, we have nr_events for that. Fix this by
touching ref_count only when we actually have a new user -
subsystem_open().
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Link: http://lkml.kernel.org/r/1320052062-7846-1-git-send-email-idryomov@gmail.com
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
More consistency cleanups. Drop the _OFF, separate and indent
CTRL/CAP/STATUS bit definitions. This helped find the previous
mis-use of bit 0 in the PASID capability register.
Reviewed-by: Joerg Roedel <joerg.roedel@amd.com>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PASID ECN indicates bit 0 is reserved in the capability register.
Switch pci_enable_pasid() to error if PASID is already enabled and
don't expose enable as a feature in pci_pasid_features().
Reviewed-by: Joerg Roedel <joerg.roedel@amd.com>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I traced a nasty kexec on panic boot failure to the fact that we had
screaming msi interrupts and we were not disabling the msi messages at
kernel startup. The booting kernel had not enabled those interupts so
was not prepared to handle them.
I can see no reason why we would ever want to leave the msi interrupts
enabled at boot if something else has enabled those interrupts. The pci
spec specifies that msi interrupts should be off by default. Drivers
are expected to enable the msi interrupts if they want to use them. Our
interrupt handling code reprograms the interrupt handlers at boot and
will not be be able to do anything useful with an unexpected interrupt.
This patch applies cleanly all of the way back to 2.6.32 where I noticed
the problem.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Modify pci_acpi_wake_dev() to avoid resuming PME-capable devices
whose PME Status bits are not set, which may happen currently if
several devices are associated with the same wakeup GPE and all
of them are notified whenever at least one of them signals PME.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the kernel has requested control of the SHPC native hotplug
feature for a given root bridge, the acpiphp driver should not try
to handle that root bridge and it should leave it to shpchp.
Failing to do so causes problems to happen if shpchp is loaded
and unloaded before loading acpiphp (ACPI-based hotplug won't work
in that case anyway).
To address this issue make find_root_bridges() ignore PCI root
bridges with SHPC native hotplug enabled and make add_bridge()
return error code if SHPC native hotplug is enabled for the given
root bridge. This causes acpiphp to refuse to load if SHPC native
hotplug is enabled for all root bridges and to refuse binding to
the root bridges with SHPC native hotplug enabled.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in pciehp as a result.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix improper workqueue cleanup.
In the current pciehp, pcied_cleanup() calls destroy_workqueue()
before calling pcie_port_service_unregister(). This causes kernel oops
because flush_workqueue() is called in the pcie_port_service_unregister()
code path after the workqueue was destroyed. So pcied_cleanup() must call
pcie_port_service_unregister() first before calling destroy_workqueue().
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Right now we forcibly clear ASPM state on all devices if the BIOS indicates
that the feature isn't supported. Based on the Microsoft presentation
"PCI Express In Depth for Windows Vista and Beyond", I'm starting to think
that this may be an error. The implication is that unless the platform
grants full control via _OSC, Windows will not touch any PCIe features -
including ASPM. In that case clearing ASPM state would be an error unless
the platform has granted us that control.
This patch reworks the ASPM disabling code such that the actual clearing
of state is triggered by a successful handoff of PCIe control to the OS.
The general ASPM code undergoes some changes in order to ensure that the
ability to clear the bits isn't overridden by ASPM having already been
disabled. Further, this theoretically now allows for situations where
only a subset of PCIe roots hand over control, leaving the others in the
BIOS state.
It's difficult to know for sure that this is the right thing to do -
there's zero public documentation on the interaction between all of these
components. But enough vendors enable ASPM on platforms and then set this
bit that it seems likely that they're expecting the OS to leave them alone.
Measured to save around 5W on an idle Thinkpad X220.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These are extended capabilities, rename and move to proper
group for consistency.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds a per-pci-device subdirectory in sysfs called:
/sys/bus/pci/devices/<device>/msi_irqs
This sub-directory exports the set of msi vectors allocated by a given
pci device, by creating a numbered sub-directory for each vector beneath
msi_irqs. For each vector various attributes can be exported.
Currently the only attribute is called mode, which tracks the
operational mode of that vector (msi vs. msix)
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If ipv4_valdiate_peer() fails during a cached entry lookup,
we'll NULL derer since the loop iterator assumes rth is not
NULL.
Letting this be handled as a failure is just bogus, so just make it
not fail. If we have trouble getting a non-NULL neighbour for the
redirected gateway, just restore the original gateway and continue.
The very next use of this cached route will try again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Satellite C670-10V generates notifications for hotkeys but does
not support HCI_SYSTEM_EVENT. As a result when a hotkey is pressed
it gets stuck in an infinite loop in toshiba_acpi_notify. To fix
this, detect whether or not HCI_SYSTEM_EVENT is supported up-front
and don't try to read system events if it isn't supported. In
addition, limit the number of retries when reading HCI_SYSTEM_EVENT
fails so that this loop cannot run unbounded.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Otherwise timing is inaccurate, resulting in devices which depend on it,
like omap-keypad, broken.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix:
Section mismatch in reference from the function
ir_dev_scope_init() to the function
.init.text:dmar_dev_scope_init() The function
ir_dev_scope_init() references the function __init dmar_dev_scope_init().
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Youquan Song <youquan.song@intel.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Link: http://lkml.kernel.org/r/20111026161507.GB10103@swordfish
Signed-off-by: Ingo Molnar <mingo@elte.hu>
dmar_parse_rmrr_atsr_dev() calls rmrr_parse_dev() and
atsr_parse_dev() which are both marked as __init.
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
Section mismatch in reference from the function
dmar_parse_rmrr_atsr_dev() to the function
.init.text:dmar_parse_dev_scope() The function
dmar_parse_rmrr_atsr_dev() references the function __init
dmar_parse_dev_scope().
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Link: http://lkml.kernel.org/r/20111026154539.GA10103@swordfish
Signed-off-by: Ingo Molnar <mingo@elte.hu>
