NR_BUILTIN_GPIO is both defined in arch-pxa and arch-mmp. Now replace it
with PXA_NR_BUILTIN_GPIO and MMP_NR_BUILTIN_GPIO.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Use cpuid to recognize the gpio number and type. CPU_PXA26x is the
special case since we can't identify it by cpuid.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to define gpio_to_irq() and irq_to_gpio() for potential name
confliction since multiple architecture will be built together.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
GPIO0 and GPIO1 are linked to unique interrupt line in PXA series,
others are linked to another interrupt line. All GPIO are linked to one
interrupt line in MMP series.
Since gpio driver is shared between PXA series and MMP series, define
GPIO0 and GPIO1 as chained interrupt chip. So we can move out gpio code
from irq.c to gpio-pxa.c.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Avoid potential naming confliction since multiple architecture will be built
in a single kernel.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Commit ["62016250 lockdep: Add improved subclass caching"] tries to
improve performance (expecially to reduce the cost of rq->lock)
when using lockdep, but it fails due to lockdep_init_map() in
which ->class_cache is cleared. The typical caller is
lock_set_subclass(), after that class will not be cached anymore.
This patch tries to achive the goal of commit 62016250 by always
setting ->class_cache in register_lock_class().
=== Score comparison of benchmarks ===
for i in `seq 1 10`; do ./perf bench -f simple sched messaging; done
before: min: 0.604, max: 0.660, avg: 0.622
after: min: 0.414, max: 0.473, avg: 0.427
for i in `seq 1 10`; do ./perf bench -f simple sched messaging -g 40; done
before: min: 2.347, max: 2.421, avg: 2.391
after: min: 1.652, max: 1.699, avg: 1.671
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111109080714.GC8124@zhy
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Switch to local_irq_ ops so that the irq state is properly tracked
(raw_local_irq_* isn't tracked by lockdep, causing confusion).
Possible now that commit dd4e5d3ac4 ("lockdep: Fix
trace_[soft,hard]irqs_[on,off]() recursion") cured the reason we
needed the raw_ ops.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The raw_lock_irq_{save,restore}() already implies a
non-preemptibility.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
zap_locks() is used by printk() in a last ditch effort to get data
out, clearly we cannot trust lock state after this so make it disable
lock debugging.
Also don't treat printk recursion through lockdep as a normal
recursion bug but try hard to get the lockdep splat out.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-kqxwmo4xz37e1s8w0xopvr0q@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch solves the following problem:
Now some samples may be lost due to throttling. The number of samples is
restricted by sysctl_perf_event_sample_rate/HZ. A trace event is
divided on some samples according to event's period. I don't sure, that
we should generate more than one sample on each trace event. I think the
better way to use SAMPLE_PERIOD.
E.g.: I want to trace when a process sleeps. I created a process, which
sleeps for 1ms and for 4ms. perf got 100 events in both cases.
swapper 0 [000] 1141.371830: sched_stat_sleep: comm=foo pid=1801 delay=1386750 [ns]
swapper 0 [000] 1141.369444: sched_stat_sleep: comm=foo pid=1801 delay=4499585 [ns]
In the first case a kernel want to send 4499585 events and
in the second case it wants to send 1386750 events.
perf-reports shows that process sleeps in both places equal time. It's
bug.
With this patch kernel generates one event on each "sleep" and the time
slice is saved in the field "period". Perf knows how handle it.
Signed-off-by: Andrew Vagin <avagin@openvz.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1320670457-2633428-3-git-send-email-avagin@openvz.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Split the callchain code from the perf events core into
a new kernel/events/callchain.c file.
This simplifies a bit the big core.c
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
[keep ctx recursion handling inline and use internal headers]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1318778104-17152-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It appears that stop_machine_text_poke() wants to be called on all CPUs,
like it's done from text_poke_smp(). Fix text_poke_smp_batch() to do
this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Jason Baron <jbaron@redhat.com>
Link: http://lkml.kernel.org/r/1319702072-32676-1-git-send-email-rabin@rab.in
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the core offcore support is fixed up (thanks Stephane) and we
have sane generic events utilizing them, re-enable the raw access to
the feature as well.
Note that it doesn't matter if you use event 0x1b7 or 0x1bb to specify
an offcore event, either one works and neither guarantees you'll end
up on a particular offcore MSR.
Based on original patch from: Vince Weaver <vweaver1@eecs.utk.edu>.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Vince Weaver <vweaver1@eecs.utk.edu>.
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1108031200390.703@cl320.eecs.utk.edu
Signed-off-by: Ingo Molnar <mingo@elte.hu>
People (Linus) objected to using -ENOSPC to signal not having enough
resources on the PMU to satisfy the request. Use -EINVAL.
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-xv8geaz2zpbjhlx0svmpp28n@git.kernel.org
[ merged to newer kernel, fixed up MIPS impact ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do not set task_ctx pointer during sched_in if there are no
events associated with the context. Otherwise if during task
execution total number of events in the system will become zero
perf_event_context_sched_out() will not be called and cpuctx->task_ctx
will be left with a stale value.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111023171033.GI17571@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Masami spotted that we always try to decode the instruction stream as
64bit instructions when running a 64bit kernel, this doesn't work for
ia32-compat proglets.
Use TIF_IA32 to detect if we need to use the 32bit instruction
decoder.
Reported-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: stable@kernel.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In UP systems, the idle task is initialized using the init_task
structure from which the command name is taken (currently "swapper").
In SMP systems, one idle task per CPU is forked by the worker thread
from which the task structure is copied. The command name is, therefore,
"kworker/0:0" or "kworker/0:1", if not updated. Since such update was
lacking, all idle tasks in SMP systems were incorrectly named. This
longtime bug was not discovered immediately, because there is no /proc/0
entry - the bug only becomes apparent when tracing is enabled.
This patch sets the command name of the idle tasks in SMP systems to the
name that is used in the INIT_TASK structure suffixed by a slash and the
number of the CPU.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111026211708.768925506@osadl.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Normally the RT bandwidth scheme will share bandwidth across the
entire root_domain. However sometimes its convenient to disable this
sharing for debug purposes. Provide a simple feature switch to this
end.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The return-value convention for these functions varies depending on
whether they're interruptible or can timeout. It can be a little
confusing--document it.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111006192246.GB28026@fieldses.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Every time I have to stare at this function I need to completely
reverse engineer its workings, about time I write a comment
explaining the thing.
Collected bits and pieces from previous changelogs, mostly:
4be9daaa1b83378269a5
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1318518057.27731.2.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make sure that all cpus in a book on a z10 appear as book siblings
and not as core siblings. This fixes some performance regressions that
appeared after the book scheduling domain got introduced.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MSA3 and MSA4 instructions are only available under CONFIG_64BIT.
Bail out before using any of these instructions if the kernel is
running in 31 bit mode.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In ESA mode STCKF is not defined even if the facility bit is enabled.
To prevent an illegal operation we must also check if we run a 64 bit kernel.
To make the check perform well add the STCKF bit to the machine flags.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the kernel is started in kdump mode, zfcpdump should not be
initialized because both dump methods can't be used at the same time.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setup timer for processing messages in request queue, if sending an AP
message returns with reason code AP_RESPONSE_RESET_IN_PROGRESS.
Signed-off-by: Holger Dengler <hd@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kdump infrastructure is built on top of kexec. Therefore
CONFIG_KEXEC has to be enabled when CONFIG_CRASH_DUMP is selected.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
'readelf -n' on the s390 vmlinux file generates lots of warnings about
corrupt notes. The reason is that the 'NOTE' program header has incorrect
file and memory sizes. The problem is that the section following the
NOTES section do not switch to a different phdr and they get added to
the NOTE program section. Add a dummy entry to the linker script that
switches to the data phdr before the start of the RODATA section.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ignore completion interrupts if the initial interrupt hasn't been
received and the addressed task is not running. This case can only
happen if leftover (pending) completion interrupt gets delivered
which wasn't removed with the PFAULT CANCEL operation during cpu
hotplug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The pgste_update_all / pgste_update_young and pgste_set_pte need to
check if the pte entry contains a valid page address before the storage
key can be accessed. In addition pgste_set_pte needs to set the access
key and fetch protection bit of the new pte entry, not the old entry.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no Kconfig symbol named SPI_MASTER_OF. The select statement for
that symbol is a nop. Drop it.
While we're touching that Kconfig entry also drop a superfluous
dependency on SPI (this entry is wrapped in "if SPI" / "endif").
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I assumed all PCI buses had a bridge, but playing with qemu recently, I
discovered vgaarb bug where it wasn't detecting both devices shared a bridge
at the root level.
Don't check for NULL, if two buses have a NULL bridge, assume they share the
root bus.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is no Kconfig symbol named USB_GADGET_S3C_HSOTG_PIO. The select
statement for that symbol is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 27641c3f (drm/vblank: Add support for precise vblank
timestamping) adds preempt_disable()/enable() around a spin locked
section with the comments:
* Disable preemption, so vblank_time_lock is held as short as
* possible, even under a kernel with PREEMPT_RT patches.
/* Disable preemption while holding vblank_time_lock. Do
* it explicitely to guard against PREEMPT_RT kernel.
Just that this has never been tested on a RT kernel which would have
granted that nonsense with a might_sleep() warning because
dev->vblank_time_lock is converted to a "sleeping" spinlock on RT.
So this is activly wrong on RT and superflous on mainline. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 8dc7a9c84 ("blackfin: Add export.h to files using
EXPORT_SYMBOL/THIS_MODULE") inserted some of the include statements into
sections protected by an unrelated #if CONFIG_... statement. This can cause,
depending on the configuration used, warnings like this one:
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: data definition has no type or storage class
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/blackfin/mach-bf537/boards/stamp.c:2940: warning: parameter names (without types) in function declaration
This patch fixes it by moving the includes out of the #if protected sections.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
The serial TX IRQ is not simply (RX IRQ + 1) on some Blackfin chips,
so move the values to the platform resources.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
Since 952c5ca1 (fsl_pq_mdio: Clean up tbi address configuration) .probe returns
-EBUSY when the "tbi-phy" node is missing. Fix this.
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3ceca74966 added a TOS attribute.
Unfortunately TOS and TCLASS are both present in a dual-stack v6 socket,
furthermore they can have different values. As such one cannot in a
sane way expose both through a single attribute.
Signed-off-by: Maciej Żenczyowski <maze@google.com>
CC: Murali Raja <muralira@google.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds listen only mode to the mscan controller.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checking for valid magic values (needed for stability in the event
corrupted packets are received) and remove some other unneeded checks.
Also, fix flagging device as WWAN (Bugzilla bug #39952).
Signed-off-by: Mark Kamichoff <prox@prolixium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le mercredi 09 novembre 2011 à 16:21 -0500, David Miller a écrit :
> From: David Miller <davem@davemloft.net>
> Date: Wed, 09 Nov 2011 16:16:44 -0500 (EST)
>
> > From: Eric Dumazet <eric.dumazet@gmail.com>
> > Date: Wed, 09 Nov 2011 12:14:09 +0100
> >
> >> unres_qlen is the number of frames we are able to queue per unresolved
> >> neighbour. Its default value (3) was never changed and is responsible
> >> for strange drops, especially if IP fragments are used, or multiple
> >> sessions start in parallel. Even a single tcp flow can hit this limit.
> > ...
> >
> > Ok, I've applied this, let's see what happens :-)
>
> Early answer, build fails.
>
> Please test build this patch with DECNET enabled and resubmit. The
> decnet neigh layer still refers to the removed ->queue_len member.
>
> Thanks.
Ouch, this was fixed on one machine yesterday, but not the other one I
used this morning, sorry.
[PATCH V5 net-next] neigh: new unresolved queue limits
unres_qlen is the number of frames we are able to queue per unresolved
neighbour. Its default value (3) was never changed and is responsible
for strange drops, especially if IP fragments are used, or multiple
sessions start in parallel. Even a single tcp flow can hit this limit.
$ arp -d 192.168.20.108 ; ping -c 2 -s 8000 192.168.20.108
PING 192.168.20.108 (192.168.20.108) 8000(8028) bytes of data.
8008 bytes from 192.168.20.108: icmp_seq=2 ttl=64 time=0.322 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
More changes to the recent code to support control of forwarding
database via netlink.
* Support NTF_USE like neighbour table
* Validate state bits from application
* Only send notifications (and change bits) if new entry is
different.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
