CC [M] drivers/net/wireless/b43/pio.o
drivers/net/wireless/b43/pio.c: In function ‘pio_rx_frame’:
drivers/net/wireless/b43/pio.c:614:6: warning: ‘macstat’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't know yet when to restore it, implement just reading. We found
out what for are that PHY ops by comparing HT with N code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Comparison of the HT and N code has shown similarities in the ops
performed after b43_mac_phy_clock_set. That way we understood what is
happening in the HT-PHY code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I will suck out stuff to userspace to start the regulatory
revampamp, this work will be permissively licensed.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add uapsd_queues and max_sp fields to ieee80211_sta.
These fields might be needed by low-level drivers in
order to configure the AP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new NL80211_ATTR_STA_WME nested attribute that contains
wme params needed by the low-level driver (uapsd_queues and
max_sp).
Add these params to the station_parameters struct as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating as a P2P GO, we receive some P2P action frames where the
BSSID is set to the peer MAC address. Specifically, this occurs for
invitation responses. These are valid action frames and they should be
passed up.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the aggregation is formed till the aggregation limit
is reached and the rate lookup is done for the first frame alone.
But there can be a legacy rated frames in tid queue. This patch
limits the subframe addition based on presence of legacy rate and
sends the legacy rated frames as unaggregated one.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When associating to an AP, the station might miss the first EAP
packet that the AP sends due to a race condition between the association
success procedure and the rx flow in mac80211.
In such cases, the packet might fall in ieee80211_rx_h_check due to
the fact that the relevant rx->sta wasn't allocated yet.
Allocation of the relevant station info struct before actually
sending the association request and setting it with a new
dummy_sta flag solve this problem.
The station will accept only EAP packets from the AP while it
is in the pre-association/dummy state.
This dummy station entry is not seen by normal sta_info_get()
calls, only by sta_info_get_bss_rx().
The driver is not notified for the first insertion of the
dummy station. The driver is notified only after the association
is complete and the dummy flag is removed from the station entry.
That way, all the rest of the code flow should be untouched by
this change.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divided the sta_info_insert_rcu function to 3 mini-functions:
sta_info_insert_check - the initial checks done when inserting
a new station
sta_info_insert_ibss - the function that handles the station
addition for IBSS interfaces
sta_info_insert_non_ibss - the function that handles the station
addition in other cases
The outer API was not changed.
The refactoring was done for better usage of the different
stages in the station addition in new scenarios added
in the next commit.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have module param called use_pio which is much easier to use.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since a v1 of the mesh gate series was accidentally applied, this patch
contains the changes in v2.
These are:
- automatically make mesh gate a root node.
- use TU_TO_EXP_TIME macro.
- initialize timer instead of checking for NULL timer function.
- cleanups.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for Starr Labs USB MIDI devices such as the Z7S, which are
based on an FTDI serial UART chip.
Based on a patch by Daniel Mack.
Signed-off-by: Kristian Amlie <kristian@amlie.name>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The omap_iommu_set_isr() was still using the mutex functions
but the iommu_lock was converted to a spin_lock. Fix that
up.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The dark space calculation should be 64 bit type-casted, when
assigning to tmp64 (similar to how total_free is calculated).
Overflow will occur for very large flashes.
Signed-off-by: srimugunthan <srimugunthan.dhandapani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Prepend 'omap_' to OMAP's 'struct iommu' and exposed API, to prevent
namespace pollution and generally to improve readability of the code
that still uses the driver directly.
Update the users as needed as well.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Remove unused public APIs from OMAP's iommu driver.
IOMMU functionality should be exposed only via the generic IOMMU API;
this way drivers stay generic, and different IOMMU drivers
don't need to duplicate similar functionalities.
The rest of the API still exposed by OMAP's iommu will be evaluated
and eventually either added to the generic IOMMU API (if relevant),
or completely removed.
The intention is that OMAP's iommu driver will eventually not expose
any public API.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Remove unused functionality from OMAP's iovmm module.
The intention is to eventually completely replace iovmm with the
generic DMA-API, so new code that'd need this iovmm functionality
will have to extend the DMA-API instead.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Use PREFETCH_IOTLB to control the content of the called function,
instead of inlining it in the code.
This improves readability of the code, and also prevents an "unused
function" warning to show up when PREFETCH_IOTLB isn't set.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Stop exporting functions that are used only within the iommu
driver itself.
Eventually OMAP's iommu driver should only expose API via the generic
IOMMU framework.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Move OMAP's iommu drivers to the dedicated iommu drivers folder.
While OMAP's iovmm (virtual memory manager) driver does not strictly
belong to the iommu drivers folder, move it there as well, because
it's by no means OMAP-specific (in concept. technically it is still
coupled with OMAP's iommu).
Eventually, iovmm will be completely replaced with the generic,
iommu-based, dma-mapping API.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Migrate OMAP's iommu driver to the generic IOMMU API, so users can stay
generic, and any generic IOMMU functionality can be developed once
in the generic framework.
Migrate omap's iovmm (virtual memory manager) to the generic IOMMU API,
and adapt omap3isp as needed, so the latter won't break.
The plan is to eventually remove iovmm completely by replacing it
with the (upcoming) IOMMU-based DMA-API.
Tested on OMAP3 (with omap3isp) and OMAP4 (with rpmsg/remoteproc).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
These were present to be able to compile this file on different
SoCs. They are not needed anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This can make the l2 cache work at early time which
will benefit the boot up time.
Tested on i.mx31pdk board, test result shows:
Before: arch_initcall(mxc_init_l2x0);
[ 0.558755] console [ttymxc0] enabled
After: early_initcall(mxc_init_l2x0);
[ 0.555716] console [ttymxc0] enabled
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Update to use generic function for displaying silicon revision
Tested on my mx53 loco board:
CPU identified as i.MX53, silicon rev 2.0
Test on my mx51 babbage board:
CPU identified as i.MX51, silicon rev 3.0
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
update to use generic function for displaying silicon revision
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Update to use generic function for displaying silicon revision
Tested on mx31pdk board as print the following information:
CPU identified as i.MX31, silicon rev 2.0
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Silicon revision is useful information to have during kernel boot.
Print the MX27 silicon revision.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Silicon revision is useful information to have during kernel boot.
Print the MX25 silicon revision.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently each i.MX processor has its own function for displaying the silicon
revision.
Introduce a generic function for this purpose, so that all i.MX processors can
reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
After merging the staging tree, today's linux-next build (x86_64
allmodconfig) failed like this:
drivers/staging/rtl8192e/rtl_core.c:2917:2: error: unknown field 'ndo_set_multicast_list' specified in initializer
Caused by commit 94a799425e ("From: wlanfae <wlanfae@realtek.com>" -
really "[PATCH 1/8] rtl8192e: Import new version of driver from realtek"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
This bug causes the IECSR register clear failure. In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared. So the related ISR may be called persistently.
The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous rtc-s3c had two issues related with its IRQ.
1. Users cannot open rtc multiple times because an open operation
calls request_irq on the same IRQ. (e.g., two user processes wants to
open and read RTC time from rtc-s3c at the same time)
2. If alarm is set and no one has the rtc opened with filesystem
(either the alarm is set by kernel/boot-loader or user set an alarm and
closed rtc dev file), the pending bit is not cleared and no further
interrupt is invoked. When the alarm is used by the system itself such
as a resume from suspend-to-RAM or other Low-power modes/idle, this is
a critical issue.
This patch mitigates these issues by calling request_irq at probe and
free_irq at remove.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lots of people expect module.h to just "be there" without
any #include effort. But we are crushing that. So fix those
files in staging relying on implicit module.h presence.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function obviously never worked, it was a cut-and-paste from the
probe() function. Rewrite it to do what it is supposed to do at least
in theory. As to if it works yet, well, it's not worse than it was
before, so this can't hurt.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves some functions around to remove a forward declaration.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not needed, so just inline the two lines.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not needed, so just inline the two lines.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
bd2802_unregister_led_classdev() should unregister all registered
instances of led_classdev class that had registered by
bd2802_register_led_classdev().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kim Kyuwon <q1.kim@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following build errors:
drivers/tty/serial/8250_early.c:160: error: 'BASE_BAUD' undeclared (first use in this function): 1 errors in 1 logs
drivers/tty/serial/8250_early.c:37:24: error: asm/serial.h: No such file or directory: 1 errors in 1 logs
I am not sure if (1843200 / 16) is suitable for cris, but most other
arch's define it as this value.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>