When receiving the first RX interrupt before the internal call
to napi_schedule_prep is successful the RX interrupt gets disabled
and is never enabled again as the poll function never gets executed.
Signed-off-by: Michael Thalmeier <Michael.Thalmeier@sigmatek.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coefficients to convert chip register values to voltage/current have been
slightly changed in revision B of the chip datasheet. Update driver coefficients
to match the coefficients in the datasheet.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
The registers and descriptors bits are identical to the pre-8168
8169 chipsets : {RxDesc / TxDesc}.opts2 can only contain VLAN information.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes obsolete code in the initialisation/creation of
slcan devices.
It follows the suggested cleanups from Ilya Matvejchikov in
drivers/net/slip.c that where recently applied to net-next-2.6:
- slip: remove dead code within the slip initialization
- slip: remove redundant check slip_devs for NULL
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5f77898de1 does not completely
fix the problem of handling allocations with irqs disabled.. The
below patch on top of it fixes the problem completely.
Based on review by "Ivan Vecera" <ivecera@redhat.com>..
"
Small note, the root of the problem was that non-atomic allocation was requested with IRQs disabled. Your patch description does not contain wwhy were the IRQs disabled.
The function bnad_mbox_irq_alloc incorrectly uses 'flags' var for two different things, 1) to save current CPU flags and 2) for request_irq
call.
First the spin_lock_irqsave disables the IRQs and saves _all_ CPU flags (including one that enables/disables interrupts) to 'flags'. Then the 'flags' is overwritten by 0 or 0x80 (IRQF_SHARED). Finally the spin_unlock_irqrestore should restore saved flags, but these flags are now either 0x00 or 0x80. The interrupt bit value in flags register on x86 arch is 0x100.
This means that the interrupt bit is zero (IRQs disabled) after spin_unlock_irqrestore so the request_irq function is called with disabled interrupts.
"
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WM8983 is a low power, high quality stereo CODEC
designed for portable multimedia applications. Highly flexible
analogue mixing functions enable new application features,
combining hi-fi quality audio with voice communication.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change explicit references to CONFIG_NFS_V4_1 to implicit ones
Get rid of the unnecessary defines in backchannel_rqst.c and
bc_svc.c: the Makefile takes care of those dependency.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Use nfs_pageio_reset_read_mds and nfs_pageio_reset_write_mds instead of
completely reinitialising the struct nfs_pageio_descriptor.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
...and ensure that we recoalese to take into account differences in
differences in block sizes when falling back to write through the MDS.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
...and ensure that we recoalese to take into account differences in
block sizes when falling back to read through the MDS.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If an attempt to do pNFS fails, and we have to fall back to writing through
the MDS, then we may want to re-coalesce the requests that we already have
since the block size for the MDS read/writes may be different to that of
the DS read/writes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Instead of looking up the rsize and wsize, the routines that generate the
RPC requests should really be using the pg_bsize, since that is what we
use when deciding whether or not to coalesce write requests...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Other files using dma.h may fail to compile as follows:
In file included from sound/soc/mxs/mxs-pcm.h:22,
from sound/soc/mxs/mxs-saif.h:112,
from sound/soc/mxs/mxs-sgtl5000.c:34:
arch/arm/mach-mxs/include/mach/dma.h:16: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbh':
arch/arm/mach-mxs/include/mach/dma.h:18: error: dereferencing pointer to incomplete type
arch/arm/mach-mxs/include/mach/dma.h: At top level:
arch/arm/mach-mxs/include/mach/dma.h:21: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbx':
arch/arm/mach-mxs/include/mach/dma.h:23: error: dereferencing pointer to incomplete type
make[3]: *** [sound/soc/mxs/mxs-sgtl5000.o] Error 1
make[2]: *** [sound/soc/mxs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
It seems it's better for dma.h to include dmaengine.h himself.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If both the RTS pad and CTS pad definitions setup
IOMUXC_UARTn_IPP_UART_RTS_MUX_SELECT_INPUT, then
the order of setup will matter. We don't want that.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If both the RXD pad and TXD pad definitions setup
IOMUXC_UARTn_IPP_UART_RXD_MUX_SELECT_INPUT, then
the order of setup will matter. We don't want that.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
__gfs2_free_data and __gfs2_free_meta are almost identical, and
can be trivially combined.
[This is as per Eric's original patch minus gfs2_free_data() which had
no callers left and plus the conversion of the bmap.c calls to these
functions. All in all, a nice clean up]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This adds S_NOSEC support to GFS2. We set/reset the flag either when
a user calls setattr or when we have just regained the glock
from another node. The flag is only set if there are no xattrs
on the inode and there is no suid bit set.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
This patch is a performance improvement for GFS2 in a clustered
environment. It makes the glock hold time self-adjusting.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch adds a cache for the hash table to the directory code
in order to help simplify the way in which the hash table is
accessed. This is intended to be a first step towards introducing
some performance improvements in the directory code.
There are two follow ups that I'm hoping to see fairly shortly. One
is to simplify the hash table reading code now that we always read the
complete hash table, whether we want one entry or all of them. The
other is to introduce readahead on the heads of the hash chains
which are referred to from the table.
The hash table is a maximum of 128k in size, so it is not worth trying
to read it in small chunks.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The I2C controller requires the SION bit to be set on SDA and SCL pins.
This is missing on some pad definitions for the I2C function.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
BugLink: https://bugs.launchpad.net/bugs/774895
The original reporter states that his volume keys do not change the
desired Master and PCM mixer elements together, so apply the hp+mute led
quirk for his PCI SSID.
Reported-by: Jeffrey Finkelstein
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Include the device id in the bus-id to give userspace a way to open
the correct "cardN" when there are multiple device instances.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
handle_signal()->set_fs() has a nice comment which explains what
set_fs() is, but it doesn't explain why it is needed and why it
depends on CONFIG_X86_64.
Afaics, the history of this confusion is:
1. I guess today nobody can explain why it was needed
in arch/i386/kernel/signal.c, perhaps it was always
wrong. This predates 2.4.0 kernel.
2. then it was copy-and-past'ed to the new x86_64 arch.
3. then it was removed from i386 (but not from x86_64)
by b93b6ca3 "i386: remove unnecessary code".
4. then it was reintroduced under CONFIG_X86_64 when x86
unified i386 and x86_64, because the patch above didn't
touch x86_64.
Remove it. ->addr_limit should be correct. Even if it was possible
that it is wrong, it is too late to fix it after setup_rt_frame().
Linus commented in:
http://lkml.kernel.org/r/alpine.LFD.0.999.0707170902570.19166@woody.linux-foundation.org
... about the equivalent bit from i386:
Heh. I think it's entirely historical.
Please realize that the whole reason that function is called "set_fs()" is
that it literally used to set the %fs segment register, not
"->addr_limit".
So I think the "set_fs(USER_DS)" is there _only_ to match the other
regs->xds = __USER_DS;
regs->xes = __USER_DS;
regs->xss = __USER_DS;
regs->xcs = __USER_CS;
things, and never mattered. And now it matters even less, and has been
copied to all other architectures where it is just totally insane.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710164424.GA20261@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
1. do_signal() looks at TS_RESTORE_SIGMASK and calculates the
mask which should be stored in the signal frame, then it
passes "oldset" to the callees, down to setup_rt_frame().
This is ugly, setup_rt_frame() can do this itself and nobody
else needs this sigset_t. Move this code into setup_rt_frame.
2. do_signal() also clears TS_RESTORE_SIGMASK if handle_signal()
succeeds.
We can move this to setup_rt_frame() as well, this avoids the
unnecessary checks and makes the logic more clear.
3. use set_current_blocked() instead of sigprocmask(SIG_SETMASK),
sigprocmask() should be avoided.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710182203.GA27979@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
sys_sigsuspend() and sys_sigreturn() change ->blocked directly.
This is not correct, see the changelog in e6fa16ab
"signal: sigprocmask() should do retarget_shared_pending()"
Change them to use set_current_blocked().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710192727.GA31759@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
sys32_sigsuspend() and sys32_*sigreturn() change ->blocked directly.
This is not correct, see the changelog in e6fa16ab
"signal: sigprocmask() should do retarget_shared_pending()"
Change them to use set_current_blocked().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710192724.GA31755@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
caam now supports encrypt and decrypt
for aes, des and 3des
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Job descriptors only contain header and seq pointers.
Other commands are stored in separate shared descriptors
for encrypt, decrypt and givencrypt, stored as arrays
in caam_ctx.
This requires additional macros to create math commands
to calculate assoclen and cryptlen.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam_ctx.key_phys to key_dma
caam_alg_template supports multiple algorithm types
listed in union, which requires cases for
different types in function caam_alg_alloc
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
"aead_authenc" and "ipsec_esp" changed to "aead,"
except for function "ipsec_esp," which is changed
to "init_aead_job."
Variable name of aead_request structures changed
to "req" and name of aead_givcrypt_request structure
changed to "areq"
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto/ablkcipher.c's setkey() has already checked against the min, max
key sizes before it calls here, and all max_keysize assignments in the
algorithm template array do not exceed TALITOS_MAX_KEY_SIZE.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
IRQ done notification is always set. Remove its explicit
assignment from the hot path by including it in the
descriptor header template assignment in talitos_cra_init.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Assign single target channel per tfm in talitos_cra_init instead of
performing channel scheduling dynamically during the encryption request.
This changes the talitos_submit interface to accept a new channel
number argument. Without this, rapid bursts of misc. sized requests
could make it possible for IPsec packets to be encrypted out-of-order,
which would result in packet drops due to sequence numbers falling
outside the anti-reply window on a peer gateway.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enabling function tracer to trace all functions, then load a module and
then disable function tracing will cause ftrace to fail.
This can also happen by enabling function tracing on the command line:
ftrace=function
and during boot up, modules are loaded, then you disable function tracing
with 'echo nop > current_tracer' you will trigger a bug in ftrace that
will shut itself down.
The reason is, the new ftrace code keeps ref counts of all ftrace_ops that
are registered for tracing. When one or more ftrace_ops are registered,
all the records that represent the functions that the ftrace_ops will
trace have a ref count incremented. If this ref count is not zero,
when the code modification runs, that function will be enabled for tracing.
If the ref count is zero, that function will be disabled from tracing.
To make sure the accounting was working, FTRACE_WARN_ON()s were added
to updating of the ref counts.
If the ref count hits its max (> 2^30 ftrace_ops added), or if
the ref count goes below zero, a FTRACE_WARN_ON() is triggered which
disables all modification of code.
Since it is common for ftrace_ops to trace all functions in the kernel,
instead of creating > 20,000 hash items for the ftrace_ops, the hash
count is just set to zero, and it represents that the ftrace_ops is
to trace all functions. This is where the issues arrise.
If you enable function tracing to trace all functions, and then add
a module, the modules function records do not get the ref count updated.
When the function tracer is disabled, all function records ref counts
are subtracted. Since the modules never had their ref counts incremented,
they go below zero and the FTRACE_WARN_ON() is triggered.
The solution to this is rather simple. When modules are loaded, and
their functions are added to the the ftrace pool, look to see if any
ftrace_ops are registered that trace all functions. And for those,
update the ref count for the module function records.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>