The dynamic algorithm, while now working, doesn't have good
performance in 40G mode.
One part of this patch addresses the high CPU utilization of some small
streaming workloads that the driver should reduce CPU in.
It also changes the minimum ITR that the dynamic algorithm
will settle on, causing our minimum latency to go from 12us
to about 14us, when using adaptive mode.
It also changes the BULK interrupt rate to allow maximum throughput
on a 40Gb connection with a single thread of transmit, clamping
interrupt rate to 8000 for TX makes single thread traffic go too
slow.
The new ULTRA bulk setting is introduced and is used
when the Rx packet rate on this queue exceeds 40000 packets per
second. This value of 40000 was chosen because the automatic tuning
of minimum ITR=20us means that a single queue can't quite achieve
that many packets per second from a round-robin test.
Change-ID: Icce8faa128688ca5fd2c4229bdd9726877a92ea2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was using a value expressed in 2us increments
for the divisor to figure out our bytes/usec values.
Fix the usecs variable to contain a value in microseconds.
Change-ID: I5c20493103c295d6f201947bb908add7040b7c41
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves a multi-line register setting into a function
which simplifies reading the flow of the enable function.
This also fixes a bug where the enable function was enabling
the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx.
Change-ID: Ie308f9d0d48540204590cb9d7a5a7b1196f959bb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VF driver is unable to communicate with the PF, it just gives
up and never tries again. Aside from the obvious character flaw that
this shows, it's also a lousy user experience.
When PF communications fail, wait five seconds, and try again. And
again. Don't give up, little VF driver! Your prince will come!
Change-ID: Ia1378a39879883563b8faffce819f375821f9585
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The DPAD RGB output can be driven by both DU0 and DU1 on R8A7791. Mark
the DU0 connection as possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver requires OF support, add a dependency in Kconfig and remove
the platform_device_id table that isn't used anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The i40e_intr and i40e/i40evf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acquire NVM, before issuing an AQ read nvm command for X722.
We need to acquire the NVM before issuing an AQ read to the NVM
otherwise we will get EBUSY from the FW. Also release when done.
This fixes the two X722 issues with respect to eeprom checksum verify
and reading NVM version info.
With this patch in place, i40e driver will provide basic support
for X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The defines from the RSS enabling call were mistakenly
missed in the patches to the i40e which should have been
to i40evf as well.
This is a follow up to (commit ed921559886dd40528) "fix
32 bit build warnings".
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a spinlock which is to be used for synchronizing
access to VSI's MAC filter list.
This patch also synchronizes execution of other codepaths which are
accessing VSI's MAC filter list with execution of
service_task:sync_vsi_filters.
In function i40e_add_vsi, copied out LAA MAC address instead of cloning
MAC filter entry because only MAC address is needed to remove MAC VLAN
filter from FW/HW.
Change-ID: I0e10ac7c715d44aa994239642aa4d57c998573a2
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need to check sampling output fields for events without
perf_event_attr::sample_type field set.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1444992092-17897-51-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding data arg to cpu_map__build_map callback, so we could pass data
along to the callback. It'll be needed in following patches to retrieve
topology info from perf.data.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1444992092-17897-41-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We'll need to call it from perf stat in the stat_script patchkit
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1444992092-17897-40-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding AGGR_UNSET mode, so we could distinguish unset aggr_mode in
following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1444992092-17897-30-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It's used as the perf_evsel::priv data, so the name suits better. Also
we'll need the perf_stat name free for more generic struct.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Kan Liang <kan.liang@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1444992092-17897-29-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
fncpy() requires that the source and the destination are both 8-byte
aligned.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: d94e688cae ("ARM: at91/pm: move the copying the sram function to the sram initialization phase")
Cc: <stable@vger.kernel.org> # 4.1+
We have to exclude memory locations <= PAGE_SIZE from
the condition and let the kernel mode fault path catch it.
Otherwise a kernel NULL pointer exception will be reported
as a kernel user space access.
Fixes: d2313084e2 (um: Catch unprotected user memory access)
Signed-off-by: Richard Weinberger <richard@nod.at>
If UML is executing a helper program it is using
waitpid() with the __WCLONE flag to wait for the program
as the helper is executed from a clone()'ed thread.
While using __WCLONE is perfectly fine for clone()'ed
childs it won't detect terminated childs if the helper
has issued an execve().
We have to use __WALL to wait for both clone()'ed and
regular childs to detect the termination before and
after an execve().
Reported-and-tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
modify_ldt() was declared as an external symbol. Despite the man
page for this syscall telling that there is no wrapper in glibc,
since version 2.1 there actually is, so linking to the glibc
works.
Since modify_ldt() is not a POSIX interface, other libc
implementations do not always provide a wrapper function.
Even glibc headers do not provide a corresponding declaration.
So go the recommended way to call this using syscall().
Signed-off-by: Hans-Werner Hilse <hwhilse@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Commit 30b11ee9a (um: Remove copy&paste code from init.h)
uncovered an issue wrt. out-of-tree builds.
For out-of-tree builds, we must not rely on relative paths.
Before 30b11ee9a it worked by chance as no host code included
generated header files.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Implement an ARM delay timer to be used for udelay() on Armada 37x
platforms. This allows us to skip the delay loop calibration at boot,
saving 180ms on the boot time of the kernel (which is around 10%).
It also means that udelay() will be unaffected by CPU frequency changes
when cpufreq is enabled on these platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PWM fan control is only available with DPM. There is no non-DPM
support on amdgpu, so we should never get a crash here because
the sysfs nodes would never be created in the first place. Add the
check just in case to be on the safe side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The AT91 SDHCI device has been introduced with Atmel SAMA5D2 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Flexcom device has been introduced with Atmel SAMA5D2 SoC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Capitalize 'usage' to make it consistent with all the other 'Usage' in
the codes, e.g., usage_builtin.
Signed-off-by: Yunlong Song <yunlong.song@huawei.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Sriram Raghunathan <sriram.r@nokia.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1444894792-2338-3-git-send-email-yunlong.song@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This driver also supports adau1328, thus add adau1328 to ad193x_spi_id.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the driver to use unfied device property API instead of OF one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pdev member is not used anywhere, thus remove it. Moreover struct
dw_spi_pci becomes an equivalent of struct dw_spi and therefore remove entire
struct dw_spi_pci.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper disables SPI controller and sets clock to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx_threshold and rx_threshold variables are not used anywhere. Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point to have a separate variable for speed in ->transfer_one().
While here, remove !chip->clk_div from a condition since it is assigned
simultaneously with chip->speed_hz. We can do this safely because
a) transfer speed can't be higher than max_freq and therefore chip->clk_div
can be 0 only when chip->speed_hz is 0, and
b) transfer speed can't be 0, otherwise we will get division by zero
exception.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry over spi->bits_per_word and Co from ->setup() in
struct chip_data since ->transfer_one() will anyway take the transfer
parameters from struct spi_transfer. This is since SPI core validates both
bits_per_word transfer parameter and defaults to spi->bits_per_word in case
that per transfer parameter is not set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we recalculate cr0 each time we start a transfer the chip_data->cr0
becomes redundant. Remove it and related pieces.
This is a follow up to commit 0ed36990a9 (spi: dw: Remove needless if
statements).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name of the master device is set during registrationg which happens after
we issue the error message. Change it to plain struct device * to see which
device registration failed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the SKL I2S machine driver using Realtek ALC286S codec
in I2S mode.
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use resource managed API then we can remove snd_dmaengine_pcm_unregister()
and snd_soc_unregister_component() calls in .probe error path and .remove.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
So right now we output this text:
memcpy: Benchmark for memcpy() functions
memset: Benchmark for memset() functions
all: Test all memory access benchmarks
But the right verb to use with benchmarks is to 'run' them, not 'test'
them.
So change this (and all similar texts) to:
memcpy: Benchmark for memcpy() functions
memset: Benchmark for memset() functions
all: Run all memory access benchmarks
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1445241870-24854-15-git-send-email-mingo@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So right now there's a somewhat inconsistent mess of the benchmarking
code and options sometimes calling benchmarked functions 'functions',
sometimes calling them 'routines'.
Name them 'functions' consistently.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1445241870-24854-14-git-send-email-mingo@kernel.org
[ Updated perf-bench man page, pointed out by David Ahern ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We have three benchmarking subsystems that specify some sort of 'number
of loops' parameter - but all of them do it inconsistently:
numa: -l/--nr_loops
sched messaging: -l/--loops
mem memset/memcpy: -i/--iterations
Harmonize them to -l/--nr_loops by picking the numa variant - which is
also the most likely one to have existing scripting which we don't want
to break.
Plus improve the parameter help texts to indicate the default value for
the nr_loops variable to keep users from guessing ...
Also propagate the naming to internal variables.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1445241870-24854-13-git-send-email-mingo@kernel.org
[ Let the harmonisation reach the perf-bench man page as well ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reorder functions a bit, so that we synchronize the layout of the
memcpy() and memset() portions of the code.
This improves the code, especially after we'll add an strlcpy() variant
as well.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1445241870-24854-12-git-send-email-mingo@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
