The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Device Tree binding has been updated, update the PHY
library phy_interface_t and phy_modes to support the "internal" PHY
interface type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of Ethernet MACs have internal Ethernet PHYs and the internal
wiring makes it so that this knowledge needs to be available using the
standard 'phy-mode' property.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides some updates to the mlx5 core and netdevice drivers.
Three patches from Tariq, Introduces page reuse mechanism in non-Striding
RQ RX datapath, we allow the the RX descriptor to reuse its allocated page
as much as it could, until the page is fully consumed. RX page reuse
reduces the stress on page allocator and improves RX performance especially
with high speeds (100Gb/s).
Next four patches of the series from Or allows to offload tc flower matching
on ttl/hoplimit and header re-write of hoplimit.
The rest of the series from Yotam and Or enhances mlx5 to support FW flashing
through the mlxfw module, in a similar manner done by the mlxsw driver.
Currently, only ethtool based flashing is implemented, where both Eth and IB ports
are supported.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZTR2/AAoJEEg/ir3gV/o+HHkH/jA8uoIQgsIKP8+D6ppwChCm
pcNpNWi5eWjBwRbeDKqTVRtmKEapFf2bjhWaegsybr7oGhzyh+t6nvCEiJVoKLpd
gmcSKy7nY2PSepuMEg7bqlfj5caS3b0Nlz5sqPdclOXKYDVLytvcelOvr9OnqdAT
JqxWkJMhEpLSgFniuvIyc1uJq9j6ARW7SYWx/dKp+gTDI2KCwQ3DinsrZ+RPh42F
rxLFhGkcFuQ5cIr3QIdCM+pbr6LlAf2Fvz1Y791BARZg0XZp149C0c4smieEjU9M
ya9CWlbSvnsYZcSMXtUO8ETnrtvrEfcEM0MpZo8l4y28eWih/Ib5BiHevQG3wHA=
=L44M
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-06-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-06-23
This series provides some updates to the mlx5 core and netdevice drivers.
Three patches from Tariq, Introduces page reuse mechanism in non-Striding
RQ RX datapath, we allow the the RX descriptor to reuse its allocated page
as much as it could, until the page is fully consumed. RX page reuse
reduces the stress on page allocator and improves RX performance especially
with high speeds (100Gb/s).
Next four patches of the series from Or allows to offload tc flower matching
on ttl/hoplimit and header re-write of hoplimit.
The rest of the series from Yotam and Or enhances mlx5 to support FW flashing
through the mlxfw module, in a similar manner done by the mlxsw driver.
Currently, only ethtool based flashing is implemented, where both Eth and IB ports
are supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Buffer group mappings can be obtained using FW_PARAMs cmd for newer FW.
Since some of the bg_maps are obtained in atomic context, created another
t4_query_params_ns(), that wont sleep when awaiting mbox cmd completion.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using t4_get_mps_bg_map() for both t4_get_port_stats()
to determine which MPS Buffer Groups to report statistics on for a given
Port, and also for t4_sge_alloc_rxq() to provide a TP Ingress Channel
Congestion Map. For T4/T5 these are actually the same values (because they
are ~somewhat~ related), but for T6 they should return different values
(T6 has Port 0 associated with MPS Buffer Group 0 (with MPS Buffer Group 1
silently cascading off) and Port 1 is associated with MPS Buffer Group 2
(with 3 cascading off)).
Based on the original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The copy_to_user() function returns the number of bytes remaining but we
want to return -EFAULT here.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-06-23
1) Use memdup_user to spmlify xfrm_user_policy.
From Geliang Tang.
2) Make xfrm_dev_register static to silence a sparse warning.
From Wei Yongjun.
3) Use crypto_memneq to check the ICV in the AH protocol.
From Sabrina Dubroca.
4) Remove some unused variables in esp6.
From Stephen Hemminger.
5) Extend XFRM MIGRATE to allow to change the UDP encapsulation port.
From Antony Antony.
6) Include the UDP encapsulation port to km_migrate announcements.
From Antony Antony.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Netanel Belgazal says:
====================
net: update ena ethernet driver to version 1.2.0
This patchset contains some new features/improvements that were added
to the ENA driver to increase its robustness and are based on
experience of wide ENA deployment.
Change log:
V2:
* Remove patch that add inline to C-file static function (contradict coding style).
* Remove patch that moves MTU parameter validation in ena_change_mtu() instead of
using the network stack.
* Use upper_32_bits()/lower_32_bits() instead of casting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rx drop counter is reported by the device in the keep-alive
event.
update the driver's counter with the device counter.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ena_com_mem_addr_set(), use the above functions to split dma address
to the lower 32 bits and the higher 16 bits.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver tries to allocate msix vectors as the number of the
negotiated io queues. (with another msix vector for management).
If pci_alloc_irq_vectors() fails, the driver aborts the probe
and the ENA network device is never brought up.
With this patch, the driver's logic will reduce the number of IO
queues to the number of allocated msix vectors (minus one for management)
instead of failing probe().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA driver post Rx buffers through the Rx submission queue
for the ENA device to fill them with receive packets.
Each Rx buffer is marked with req_id in the Rx descriptor.
Newer ENA devices could consume the posted Rx buffer in out of order,
and as result the corresponding Rx completion queue will have Rx
completion descriptors with non contiguous req_id(s)
In this change the driver holds two rings.
The first ring (called free_rx_ids) is a mapping ring.
It holds all the unused request ids.
The values in this ring are from 0 to ring_size -1.
When the driver wants to allocate a new Rx buffer it uses the head of
free_rx_ids and uses it's value as the index for rx_buffer_info ring.
The req_id is also written to the Rx descriptor
Upon Rx completion,
The driver took the req_id from the completion descriptor and uses it
as index in rx_buffer_info.
The req_id is then return to the free_rx_ids ring.
This patch also adds statistics to inform when the driver receive out
of range or unused req_id.
Note:
free_rx_ids is only accessible from the napi handler, so no locking is
required
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each device reset, log to the device what is the cause
the reset occur.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using:
memset(ptr, 0x0, sizeof(struct ...))
use:
memset(ptr, 0x0, sizeor(*ptr))
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, ENA device can update the ena driver about
the desired timeout values:
These values are part of the "hardware hints" which are transmitted
to the driver as Asynchronous event through ENA async
event notification queue.
In case the ENA device does not support this capability,
the driver will use its own default values.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KASAN reports out-of-bound access in proc_dostring() coming from
proc_tcp_available_ulp() because in case TCP ULP list is empty
the buffer allocated for the response will not have anything
printed into it. Set the first byte to zero to avoid strlen()
going out-of-bounds.
Fixes: 734942cc4e ("tcp: ULP infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 31fd85816d ("bpf: permits narrower load from bpf program
context fields") permits narrower load for certain ctx fields.
The commit however will already generate a masking even if
the prog-specific ctx conversion produces the result with
narrower size.
For example, for __sk_buff->protocol, the ctx conversion
loads the data into register with 2-byte load.
A narrower 2-byte load should not generate masking.
For __sk_buff->vlan_present, the conversion function
set the result as either 0 or 1, essentially a byte.
The narrower 2-byte or 1-byte load should not generate masking.
To avoid unnecessary masking, prog-specific *_is_valid_access
now passes converted_op_size back to verifier, which indicates
the valid data width after perceived future conversion.
Based on this information, verifier is able to avoid
unnecessary marking.
Since we want more information back from prog-specific
*_is_valid_access checking, all of them are packed into
one data structure for more clarity.
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions dwmac4_dma_init_rx_chan, dwmac4_dma_init_tx_chan and
dwmac4_dma_init_channel do not need to be in global scope, so them
static.
Cleans up sparse warnings:
"symbol 'dwmac4_dma_init_rx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_tx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_channel' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
xdp: offload mode
While we discuss the representors.. :)
This set adds XDP flag for forcing offload and a attachment mode
for reporting to user space that program has been offloaded. The
nfp driver is modified to make use of the new flags, but also to
adhere to the DRV_MODE flag which should disable the HW offload.
The intended driver behaviour is:
DRV mode offload
no flags yes attempted
DRV_MODE yes no
HW_MODE no yes
Where 'yes' means required, and error will be returned if setup fails.
'Attempted' means the offload will only happen automatically if HW is
capable and offloading the program will cause no change in system
behaviour (e.g. maps don't have to bound).
Thanks to loading the program both to the driver and HW by default we
can fallback to the driver mode without disruption in case user replaces
the program with one which cannot be offloaded later.
Note that the NFP driver currently claims XDP offload support but
lacks most basic features like direct packet access.
Only change compared to the RFC is fixing the double bpf_prog_put()
which Daniel has spotted (patch 5).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of just added XDP_ATTACHED_HW.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the XDP_ATTACHED_* values to include offloaded mode.
Let drivers report whether program is installed in the driver
or the HW by changing the prog_attached field from bool to
u8 (type of the netlink attribute).
Exploit the fact that the value of XDP_ATTACHED_DRV is 1,
therefore since all drivers currently assign the mode with
double negation:
mode = !!xdp_prog;
no drivers have to be modified.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the XDP_FLAGS_HW_MODE. When it's set install the program
on the NIC and skip enabling XDP in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xdp_prog member of the adapter's data path structure is used
for XDP in driver mode. In case a XDP program is loaded with in
HW-only mode, we need to store it somewhere else. Add a new XDP
prog pointer in the main structure and use that when we need to
know whether any XDP program is loaded, not only a driver mode
one. Only release our reference on adapter free instead of
immediately after netdev unregister to allow offload to be disabled
first.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRV_MODE means that user space wants the program to be run in
the driver. Do not try to offload. Only offload if no mode
flags have been specified.
Remember what the mode is when the program is installed and refuse
new setup requests if there is already a program loaded in a
different mode. This should leave it open for us to implement
simultaneous loading of two programs - one in the drv path and
another to the NIC later.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of XDP offload flags move the driver setup into
a function. Otherwise the number of conditions in one function
would make it slightly hard to follow. The offload handler may
now be called with NULL prog, even if no offload is currently
active, but that's fine, offload code can handle that.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an installation-time flag for requesting that the program
be installed only if it can be offloaded to HW.
Internally new command for ndo_xdp is added, this way we avoid
putting checks into drivers since they all return -EINVAL on
an unknown command.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass XDP flags to the xdp ndo. This will allow drivers to look
at the mode flags and make decisions about offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael reported an UDP breakage caused by the commit b65ac44674
("udp: try to avoid 2 cache miss on dequeue").
The function __first_packet_length() can update the checksum bits
of the pending skb, making the scratched area out-of-sync, and
setting skb->csum, if the skb was previously in need of checksum
validation.
On later recvmsg() for such skb, checksum validation will be
invoked again - due to the wrong udp_skb_csum_unnecessary()
value - and will fail, causing the valid skb to be dropped.
This change addresses the issue refreshing the scratch area in
__first_packet_length() after the possible checksum update.
Fixes: b65ac44674 ("udp: try to avoid 2 cache miss on dequeue")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to TX through a monitor interface, the
conditions in iwl_mvm_tx_skb_non_sta() don't match
and the frame tries to go out from an usued TXQ.
Add a check for monitor iface, and use the AUX queue
in such a case.
In non-DQA mode the frame is sent through the
static-allocated queues anyway, so the problem is
in DQA mode only.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware crashes, the transmit queues can't make
any progress. This is why we stop the counter that monitor
the transmit queues' activity.
The call that notifies the error to the op_mode may take
a bit of time, so stop the timer of the transmit queues
earlier.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver prints "L1 Enabled - LTR Enabled" all the time as dev_info,
which is just useless noise in most cases. Convert this to
IWL_DEBUG_POWER() so we don't pollute the log unnecessarily but still
can get this info on demand.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's sometimes hard to find out which HW address the iwlwifi device is
using, for instance when reading crouded sniffer logs. To make it
easier, print out an info level message with the HW address as soon as
we know it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API allows flushing queues based on station ID and TID in A000
devices. One reason for using this is that tfd_queue_mask is only good
for 32 queues, which is not enough for A000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get an ASSERT, the fw_dump_desc pointer points to
iwl_mvm_dump_desc_assert which can't be freed since it is
a global. We still need to NULL'ify the pointer when we
call iwl_mvm_free_fw_dump_desc otherwise we will hit
int iwl_mvm_fw_dbg_collect_desc(struct iwl_mvm *mvm,
const struct iwl_mvm_dump_desc *desc,
const struct iwl_fw_dbg_trigger_tlv *trigger)
{
<snip>
if (WARN_ON(mvm->fw_dump_desc))
iwl_mvm_free_fw_dump_desc(mvm);
Fixes: b6eaa45aa1 ("iwlwifi: mvm: add the cause of the firmware dump in the dump")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When updating the mac context after association,
assoc_beacon_arrive_time is not being set, which causes the FW to
set a wrong TSF to the MAC.
Fix this by setting the assoc_beacon_arrive_time when updating the
mac context after association.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing ever checks the return value of iwl_pcie_apm_stop_master(),
so there's no point in it having one - make it return void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we need to move the scheduler write pointer by
steps of 0x40, 0x80 or 0xc0, the scheduler gets stuck.
This leads to hardware error interrupts with status:
0x5A5A5A5A or alike.
In order to work around this, detect in the transport
layer that we are going to hit this case and tell iwlmvm
to increment the sequence number of the packets. This
allows to keep the requirement that the WiFi sequence
number is in sync with the index in the scheduler Tx queue
and it also allows to avoid the problematic sequence.
This means that from time to time, we will start a queue
from ssn + 1, but that shouldn't be a problem since we
don't switch to new queues for AMPDU now that we have
DQA which allows to keep the same queue while toggling
the AMPDU state.
This bug has been fixed on 9000 devices and up.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A TID may not have traffic but still have a BA agreement
active (or being setup / torn down) since a BA agreement
can be triggered by a debugfs hook.
Just avoid to consider such a TID as inactive to make the
logic safer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the hardware is stuck, we can't read any of the memory we need to
dump it, so we end up printing only 0xa5a5a5a5, which is useless.
To solve this, poke the hardware by triggering a reset and re-enabling
the clocks if we detect a HW error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we started using threaded irqs, all the opmode calls were changed
to be called with local_bh disabled. The reason for this was it was
that mac80211 needs that. When we are handling FW errors, mac80211 is
not involved, so we don't need it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In BSS mode in the disconnection flow, mac80211 removes
the AP station before the vif is set to unassociated.
Our firmware wants it the other way around: first set
the vif as unassociated, and then remove the AP station.
In order to bridge between those two different behaviors,
iwlmvm doesn't remove the station from the firmware when
mac80211 removes it, but only after the vif is set to
unassociated. The implementation is in
iwl_mvm_bss_info_changed_station:
if (assoc state was modified && mvmvif->ap_sta_id is VALID
&& assoc state is now UNASSC)
remove_the_station_from_the_firmware()
During the recovery flow, mac80211 re-adds the AP station
and then reconfigures the vif. Since the vif is not
associated, and then, we enter the if above (which was
intended to be taken in the disconnection flow only) and
remove the station we just added. This defeats the
recovery flow.
Fix this by not removing the AP station in this flow if
we are in recovery flow.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
