This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the dump operation aware of changes on radio list and corresponding
inconsistent dumps. Changed variable name for better understanding.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[compress ternary operator]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a NL_ERR_MSG in case of creating a radio by a netlink message to give
clear output to the creating process instead of creating only a debug
message in kernel log. The same function is used for the creation while
module load, so keep the old message, although it should never be thrown
while load, because the module controls all mac addresses.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[remove message, add missing braces]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If simulation needs predictable permanent mac addresses of hwsim wireless
phy, this patch add the ability to create a new radio with a user defined
permanent mac address. Allowed mac addresses needs to be locally
administrated mac addresses (as also the former fixed 42:* and 02:* were).
To do not break the operation with legacy software using hwsim, the new
address is set twice. The problem here is, the netlink call backs use
wiphy->addresses[1] as identification of a radio and not the proposed
permanent address (wiphy->addresses[0]). This design decision is not
documented in the kernel repo, therefore this patch simply reproduces this,
but with the same address.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[make pointer const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wait for a response from the VNIC server before exiting after setting
the MAC address. The resolves an issue with bonding a VNIC client in
ALB or TLB modes. The bonding driver was changing the MAC address more
rapidly than the device could respond, causing the following errors.
"bond0: the hw address of slave eth2 is in use by the bond;
couldn't find a slave with a free hw address to give it
(this should not have happened)"
If the function waits until the change is finalized, these errors are
avoided.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle HRESP error by doing a SW reset of RX and TX and
re-initializing the descriptors, RX and TX queue pointers.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On TTC table creation, the indirection TIRs should be used instead of
the inner indirection TIRs.
Fixes: 1ae1df3a11 ("net/mlx5e: Refactor RSS related objects and code")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Shalom Lagziel <shaloml@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compared to ixgbe and other previous Intel drivers the i40e and i40evf
drivers actually reserve 2 additional descriptors in maybe_stop_tx for
cache line alignment. We need to update DESC_NEEDED to reflect this as
otherwise we are more likely to return TX_BUSY which will cause issues with
things like xmit_more.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to cancel any pending work that might update driver coalesce
settings when taking down an interface.
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.
For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:
'skb->len == 1600' from the first fragment
size = lstatus & BD_LENGTH_MASK; # 1602
size -= ETH_FCS_LEN; # 1598
size -= skb->len; # -2
Since the size is unsigned, it wraps around and causes a BUG later in
the packet handling, as shown below:
kernel BUG at ./include/linux/skbuff.h:2068!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c021ec60] skb_pull+0x24/0x44
LR [c01e2fbc] gfar_clean_rx_ring+0x498/0x690
Call Trace:
[df7edeb0] [c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable)
[df7edf20] [c01e33a8] gfar_poll_rx_sq+0x3c/0x9c
[df7edf40] [c023352c] net_rx_action+0x21c/0x274
[df7edf90] [c0329000] __do_softirq+0xd8/0x240
[df7edff0] [c000c108] call_do_irq+0x24/0x3c
[c0597e90] [c00041dc] do_IRQ+0x64/0xc4
[c0597eb0] [c000d920] ret_from_except+0x0/0x18
--- interrupt: 501 at arch_cpu_idle+0x24/0x5c
Change the size to a signed integer and then trim off any part of the
FCS that was received prior to the last fragment.
Fixes: 6c389fc931 ("gianfar: fix size of scatter-gathered frames")
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't stop device before reset owner, this means we could try to
serve any virtqueue kick before reset dev->worker. This will result a
warn since the work was pending at llist during owner resetting. Fix
this by stopping device during owner reset.
Reported-by: syzbot+eb17c6162478cc50632c@syzkaller.appspotmail.com
Fixes: 3a4d5c94e9 ("vhost_net: a kernel-level virtio server")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was found that ethtool provides unexisting module name while
it queries the specified network device for associated driver
information. Then user tries to unload that module by provided
module name and fails.
This happens because ethtool reads value of DRV_NAME macro,
while module name is defined at the driver's Makefile.
This patch is to correct Cavium CN88xx Thunder NIC driver names
(DRV_NAME macro) 'thunder-nicvf' to 'nicvf' and 'thunder-nic'
to 'nicpf', sync bgx and xcv driver names accordingly to their
module names.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockless access to __ptr_ring_full is only legal if ring is
never resized, otherwise it might cause use-after free errors.
Simply drop the lockless test, we'll drop the packet
a bit later when produce fails.
Fixes: 362899b8 ("macvtap: switch to use skb array")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
mt76
* validate CCMP PN from received frames to avoid replay attacks
qtnfmac
* support 64-bit network stats
* report more hardware information to kernel log and some via ethtool
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaa1x7AAoJEG4XJFUm622bdc8H/3JSWFnXlkrQvjZzL1NWR0Hn
vUYou/W04mgzYtXIcscNL3otDa9TGwLW6Sr5wP0MDH/TGU9zXoEZxBxnYy4zq4np
7ZP7M6VsOzOhlNNsTcNAiMGyObtIT4btrfKlmp2yvf3Sra7nHNJJmprFeuyH3f02
vk5ZQWjMcEAe0afBGPcHrzndoAvVqIHHOAbM/w694n/8cdT8edcQeQ8rwlFO6ENU
db9yqkr4RvjWv9oJwa2us6d0lolJDk8ATWhDTyZL40X9yk84XR7E0jMdN5LQ/CJj
CCCMWsDYjUpEDUJVmwLdXzGavgo43QAs9a+O+z7MDJ4uwqYkZh3rzQZay+dYLKk=
=D4LX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
mt76
* validate CCMP PN from received frames to avoid replay attacks
qtnfmac
* support 64-bit network stats
* report more hardware information to kernel log and some via ethtool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_default_channel_want_txqs() is only used in efx.c, while
efx_ptp_want_txqs() and efx_ptp_channel_type (a struct) are only used
in ptp.c. In all cases these symbols should be static.
Fixes: 2935e3c382 ("sfc: on 8000 series use TX queues for TX timestamps")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[ecree@solarflare.com: rewrote commit message]
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-26
This series contains updates to i40e and i40evf.
Michal updates the driver to pass critical errors from the firmware to
the caller.
Patryk fixes an issue of creating multiple identical filters with the
same location, by simply moving the functions so that we remove the
existing filter and then add the new filter.
Paweł adds back in the ability to turn off offloads when VLAN is set for
the VF driver. Fixed an issue where the number of TC queue pairs was
exceeding MSI-X vectors count, causing messages about invalid TC mapping
and wrong selected Tx queue.
Alex cleans up the i40e/i40evf_set_itr_per_queue() by dropping all the
unneeded pointer chases. Puts to use the reg_idx value, which was going
unused, so that we can avoid having to compute the vector every time
throughout the driver.
Upasana enable the driver to display LLDP information on the vSphere Web
Client by exposing DCB parameters.
Alice converts our flags from 32 to 64 bit size, since we have added
more flags.
Dave implements a private ethtool flag to disable the processing of LLDP
packets by the firmware, so that the firmware will not consume LLDPDU
and cause them to be sent up the stack.
Alan adds a mechanism for detecting/storing the flag for processing of
LLDP packets by the firmware, so that its current state is persistent
across reboots/reloads of the driver.
Avinash fixes kdump with i40e due to resource constraints. We were
enabling VMDq and iWARP when we just have a single CPU, which was
starving kdump for the lack of IRQs.
Jake adds support to program the fragmented IPv4 input set PCTYPE.
Fixed the reported masks to properly report that the entire field is
masked, since we had accidentally swapped the mask values for the IPv4
addresses with the L4 port numbers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-01-26
This series contains updates to ixgbe and ixgbevf.
Emil updates ixgbevf to match ixgbe functionality, starting with the
consolidating of functions that represent logical steps in the receive
process so we can later update them more easily. Updated ixgbevf to
only synchronize the length of the frame, which will typically be the
MTU or smaller. Updated the VF driver to use the length of the packet
instead of the DD status bit to determine if a new descriptor is ready
to be processed, which saves on reads and we can save time on
initialization. Added support for DMA_ATTR_SKIP_CPU_SYNC/WEAK_ORDERING
to help improve performance on some platforms. Updated the VF driver to
do bulk updates of the page reference count instead of just incrementing
it by one reference at a time. Updated the VF driver to only go through
the region of the receive ring that was designated to be cleaned up,
rather than process the entire ring.
Colin Ian King adds the use of ARRAY_SIZE() on various arrays.
Miroslav Lichvar fixes an issue where ethtool was reporting timestamping
filters unsupported for X550, which is incorrect.
Paul adds support for reporting 5G link speed for some devices.
Dan Carpenter fixes a typo where && was used when it should have been
||.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The "return 0" instruction follows other return instruction
and it makes it impossible to execute, hence remove it.
Fixes: 00fc0c51e3 ("rocker: Change world_ops API and implementation to be switchdev independant")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch suppresses the message about invalid TC mapping and wrong
selected TX queue. The root cause of this bug was setting too many
TC queue pairs on huge multiprocessor machines. When quantity of the
TC queue pairs is exceeding MSI-X vectors count then TX queue number
can be selected beyond actual TX queues amount.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The drivers for i40e and i40evf had a reg_idx value stored in the q_vector
that was going completely unused. I can only assume this was copied over
from ixgbe and nobody knew how to use it.
I'm going to make use of the value to avoid having to compute the vector
and thus the register index for multiple paths throughout the drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 36777d9fa2 ("i40e: check current configured input set when
adding ntuple filters") some code was added to report the input set
mask for a given filter when reporting it to the user.
This code is necessary so that the reported filter correctly displays
that it is or is not masking certain fields.
Unfortunately the code was incorrect. Development error accidentally
swapped the mask values for the IPv4 addresses with the L4 port numbers.
The port numbers are only 16bits wide while IPv4 addresses are 32 bits.
Unfortunately we assigned only 16 bits to the IPv4 address masks.
Additionally we assigned 32bit value 0xFFFFFFF to the TCP port numbers.
This second part does not matter as the value would be truncated to
16bits regardless, but it is unnecessary.
Fix the reported masks to properly report that the entire field is
masked.
Fixes: 36777d9fa2 ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our hardware does not allow situations where two filters might conflict
when matching. Essentially hardware only programs one filter for each
set of matching criteria. We don't support filters with overlapping
input sets, because each flow type can only use a single input set.
Additionally, different flow types will never have overlapping matches,
because of how the hardware parses the flow type before checking
matching criteria.
For this reason, we do not need or use the location number when
programming filters to hardware.
In order to avoid confusing scenarios with filters that match the same
criteria but program the flow to different queues, do not allow multiple
filters that match identical criteria to be programmed.
This ensures that we avoid odd scenarios when deleting filters, and when
programming new filters that match the same criteria.
Instead, users that wish to update the criteria for a filter must use
the same location id, or must delete all the matching filters first.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
kdump fails in the system when used in conjunction with Ethernet driver
X722/X710. This is mainly because when we are resource constrained i.e.
when we have just one online_cpus, we are enabling VMDq and iWARP. It
doesn't make sense to enable them with just one CPU and starve kdump
for lack of IRQs.
So don't enable VMDq or iWARP when we just have a single CPU.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using ethtool --set-priv-flags disable-fw-lldp <on/off> is persistent
across reboots/reloads so we need some mechanism in the driver to detect
if it's on or off on init so we can set the ethtool private flag
appropriately. Without this, every time the driver is reloaded the flag
will default to off regardless of whether it's on or off in FW.
We detect this by first attempting to program DCB and if AQ fails
returning I40E_AQ_RC_EPERM, we know that LLDP is disabled in FW.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement the private flag disable-fw-lldp for ethtool
to disable the processing of LLDP packets by the FW.
This will stop the FW from consuming LLDPDU and cause
them to be sent up the stack.
The FW is also being configured to apply a default DCB
configuration on link up.
Toggling the value of this flag will also cause a PF reset.
Disabling FW DCB will also disable DCBx.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As we have added more flags, we need to now use more
bits and have over flooded the 32 bit size. So
make it 64.
Also change all the existing bits to unsigned long long
bits.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables driver to display LLDP information on the vSphere Web
Client with Intel adapters (X710, XL710) and Distributed Virtual Switch.
Signed-off-by: Upasana Menon <upasana.menon@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the i40e/i40evf_set_itr_per_queue function by
dropping all the unneeded pointer chases. Instead we can just pull out the
pointers for the Tx and Rx rings and use them throughout the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds back the capability to turn off offloads when VF has
VLAN set. The commit 0a3b4f702f ("i40evf: enable support for VF VLAN
tag stripping control") adds the i40evf_set_features function and
changes the 'turn off' flow for offloads. This patch adds that
capability back by moving checking the VLAN option for VF to the
next statement.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reorders i40e_add_del_fdir and i40e_update_ethtool_fdir_entry
calls so that we first remove an already existing filter (inside
i40e_update_ethtool_fdir_entry using i40e_add_del_fdir) and then
we add a new one with i40e_add_del_fdir.
After applying this patch, creating multiple identical filters (with
the same location) one after another doesn't revert their behavior
but behaves correctly.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FW has the ability to return a critical error on every AQ command.
When this critical error occurs then we need to send the correct response
to the caller.
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 2de6aa3a66 ("ixgbe: Add support for padding packet")
Uses RXDCTL.RLPML to limit the maximum frame size on Rx when using
build_skb. Unfortunately that register does not work on 82599.
Added an explicit check to avoid setting this register on 82599 MAC.
Extended the comment related to the setting of RXDCTL.RLPML to better
explain its purpose.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"offset" can't be both 0x0 and 0xFFFF so presumably || was intended
instead of &&. That matches with how this check is done in other
functions.
Fixes: 73834aec71 ("ixgbe: extend firmware version support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since 5G link speed is supported by some devices, add reporting of 5G link
speed.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current code enables on X550 timestamping of all packets for any
filter, which means ethtool should not report any PTP-specific filters
as unsupported.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ARRAY_SIZE macro on array buf to determine size of the array.
Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the ARRAY_SIZE macro on various arrays to determine
size of the arrays. Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of the Tx rings we need to only clear the Tx buffer_info when
we are resetting the rings. Ideally we do this when we configure the ring
to bring it back up instead of when we are taking it down in order to avoid
dirtying pages we don't need to.
In addition we don't need to clear the Tx descriptor ring since we will
fully repopulate it when we begin transmitting frames and next_to_watch can
be cleared to prevent the ring from being cleaned beyond that point instead
of needing to touch anything in the Tx descriptor ring.
Finally with these changes we can avoid having to reset the skb member of
the Tx buffer_info structure in the cleanup path since the skb will always
be associated with the first buffer which has next_to_watch set.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) The per-network-namespace loopback device, and thus its namespace,
can have its teardown deferred for a long time if a kernel created
TCP socket closes and the namespace is exiting meanwhile. The kernel
keeps trying to finish the close sequence until it times out (which
takes quite some time).
Fix this by forcing the socket closed in this situation, from Dan
Streetman.
2) Fix regression where we're trying to invoke the update_pmtu method
on route types (in this case metadata tunnel routes) that don't
implement the dst_ops method. Fix from Nicolas Dichtel.
3) Fix long standing memory corruption issues in r8169 driver by
performing the chip statistics DMA programming more correctly. From
Francois Romieu.
4) Handle local broadcast sends over VRF routes properly, from David
Ahern.
5) Don't refire the DCCP CCID2 timer endlessly, otherwise the socket
can never be released. From Alexey Kodanev.
6) Set poll flags properly in VSOCK protocol layer, from Stefan
Hajnoczi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
VSOCK: set POLLOUT | POLLWRNORM for TCP_CLOSING
dccp: don't restart ccid2_hc_tx_rto_expire() if sk in closed state
net: vrf: Add support for sends to local broadcast address
r8169: fix memory corruption on retrieval of hardware statistics.
net: don't call update_pmtu unconditionally
net: tcp: close sock if net namespace is exiting
-----BEGIN PGP SIGNATURE-----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=r4NK
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.15-rc10-2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A fairly urgent nouveau regression fix for broken irqs across
suspend/resume came in. This was broken before but a patch in 4.15 has
made it much more obviously broken and now s/r fails a lot more often.
The fix removes freeing the irq across s/r which never should have
been done anyways.
Also two vc4 fixes for a NULL deference and some misrendering /
flickering on screen"
* tag 'drm-fixes-for-v4.15-rc10-2' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: Move irq setup/teardown to pci ctor/dtor
drm/vc4: Fix NULL pointer dereference in vc4_save_hang_state()
drm/vc4: Flush the caches before the bin jobs, as well.
Fallback to backdoor register access to collect dumps if firmware
is crashed. Fixes TID, SGE Queue Context, and MPS TCAM dump collection.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only contact firmware if it's alive _AND_ if use_bd (use backdoor
access) is not set when issuing FW_LDST_CMD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware reports error, reset FW_OK flag.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like PF, if the int_gl_idx of VF does not be set, the default
interrupt coalesce index of VF is 0. But it should be GL1 for TX
queues and GL0 for RX queues.
This patch adds the int_gl_idx setup for VF.
Fixes: 200ecda42598 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool_ops.get/set_coalesce support to VF.
Since PF and VF share the same get/set_coalesce interface,
we only need to set hns3_get/set_coalesce to the ethtool_ops
when supporting get/set_coalesce for VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlpq+ZkTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9mFcB/wPSu30a664/+wjUvXM7Zdw4ko/PRdS
deSRnjGj3epkHRyGJkdGSuPx9iGg3pqR8poMCZZmFUG+kGBmEcGQX+eyaR41zIUz
iyEgZSufYDjsW47eGBsNE01xQjoL1jcF9JM7NHmRrw4+2YF75cGE3BOGcmcV6Hjc
O5HDIpLmbeMHI4NcujgD4UG/VPnZQw3+oN9eyYUEbY5Aa2XQyW76DIJ3SyKsHQz0
K/s0uxAGo+Ap7xuoBUJpx6BBYoHYM171DTgXfH9pUB0MwqyDCq3hAyYGR+UEdIXb
IDhIcN/l5wFU8VICjYmSKgKyjjHqlixgoki2snmJxVWu0KeVl5LJ1Edv
=7jiC
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.16-20180126' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2018-01-26
this is a pull request for net-next/master consisting of 3 patches.
The first two patches target the CAN documentation. The first is by me
and fixes pointer to location of fsl,mpc5200-mscan node in the mpc5200
documentation. The second patch is by Robert Schwebel and it converts
the plain ASCII documentation to restructured text.
The third patch is by Fabrizio Castro add the r8a774[35] support to the
rcar_can dt-bindings documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>